User Manual

FCC ID: 2ASK3SC-2095T

Users Manual

Download: PDF
FCCID_4303517

FCC Part 15 C Notice CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could AIR RACER™ 2.0 void the user’s authority to operate the equipment. Indoor / Outdoor Laser Battling Drones NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: • Reorient or relocate the receiving antenna. FPO • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This product is manufactured by AMAX Group 12645 Memorial Drive Suite F1 #388 Houston, TX 77024 Propel™ and Propel RC™ are the licensed trademarks of Rooftop Group LTD Singapore. 2008 All rights reserved. Visit us at www.propelrc.com Conforms to safety requirements of FCC. INSTRUCTION BOOKLET WARNING: Never leave product charging unattended for extended periods of time. Always disconnect the battery from charger immediately after the battery is fully charged. Please refer to enclosed safety instructions. PACKAGE CONTAINS: WARNING! CHOKING HAZARD - Small parts. Not suitable for children under 3 years. Made in China AIR RACER™ 2.0 2.4G Wireless Controller Spare Parts USB Charger Instruction Manual V 1.0 & Li-Poly Rechargeable Battery 13 Colors and styles may vary. ARTWORK NO. DESCRIPTION MDSER DESIGNER DATE IM 114 x 174MM Johnny 2019/05/22

TABLE OF CONTENTS FEATURES • 6 axis gyro keeps the AIR RACER™ 2.0 stable in all conditions. Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 • Push button 360˚aerial stunts. Remote Control Battery Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 • 2 speed settings for beginner to advanced quadrocopter pilots. Charging the Battle X’s Li-Poly Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 • Laser battle game with other AIR RACER™ 2.0 battling drones. AIR RACER™ 2.0 Battery Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 • On board 2.4Ghz digital spread spectrum allows up to 8 players to battle simultaneously. AIR RACER™ 2.0 Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 REMOTE CONTROL BATTERY INSTALLATION Remote Control Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 1. Unscrew the security screw and remove the battery cover from the back of the controller. 2. Install 3 “AA” alkaline batteries into the controller as Flight Preparation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 shown in diagram A. A Syncing Your AIR RACER™ 2.0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 3. Replace the battery cover and security it. AM3.LR6.SIZE AA DC1.5V Now You Are Ready To Fly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 4. Switch the controller power on you will see the indicator lights AM3.LR6.SIZE AA DC1.5V up and feel a vibration if the batteries were installed properly. AM3.LR6.SIZE AA DC1.5V Recognizing The Front & Rear of The AIR RACER™ 2.0 . . . . . . . . . . . . . . . . . . . . . . . . 5 Speed Select Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 CHARGING THE BATTLE X’S LI-POLY BATTERY 3 x “AA” Batteries (not included) Reverse Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 1. Pop out the battery from the drone battery compartment (see illustration B). 2. Next, insert the battery into the charger then connect the USB charger to your computer’s USB port (see diagram C ). Headless Mode Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Caution: Only use this charger with a computer USB port! Do not attempt to use other USB charging devices. Flight Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3. The red LED on the charger will light up and stays on till the battery is fully charged, then the LED will turn off. Flight Practice . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 (See diagram D). Note: If the red LED light is off, either the charging is complete or the USB plug or battery is not properly connected. Adjusting The Trim . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4. Average charging time is approximately 40 minutes. A fully charged drone can fly for Calibrating The AIR RACER™ 2.0. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 approximately 5-6 minutes depending on environment and user input. Note: If plug the USB cord in without connecting battery, the red LED light will keep flashing. Interactive Battle Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 How To Perform 360º Stunt Flips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 B C D Li-Poly Battery Troubleshooting Your AIR RACER™ 2.0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Replacing The Propeller Blades. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 The red LED on the charger lights off when Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 charging is complete Battery Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 IMPORTANT: ALWAYS REMEMBER TO UNPLUG YOUR CHARGING CORD WHEN NOT IN USE! Care and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Limited 90-Day Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 AIR RACER™ 2.0 BATTERY INSTALLATION 1. Slide the battery into the battery compartmetn as shown in illustraition E. FCC Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 2. Make sure the battery is fully inserted. Caution: The battery fits only one way! Do not force it. 3. Turn on the ON/OFF switch of the AIR RACER™ 2.0, the LED lights will start flashing if you install the battary properly. E F Thank you for purchasing the AIR RACER™ 2.0 2.4 Ghz High-Performance Stunt Drone. Please read this Power On/Off instruction booklet as it contains valuable information on how to properly fly and care for your AIR RACER™ 2.0. 1 2

AIR RACER™ 2.0 DIAGRAM WARNING Safety Guard DO NOT FLY YOUR AIR RACER™ 2.0 IN FOUL WEATHER! Rotor Blades FLIGHT PREPARATION • Verify that there are 3 “AA” batteries installed the remote control unit and the AIR RACER™ 2.0 battery has been fully charged. • Make sure to be in a large open space preferably a field or a park with an open radius of at least 200 feet. • Make sure to start your drone on a clean flat level surface before take-off. • IMPORTANT! Until you have experience in flying your AIR RACER™ 2.0, it is not advised to use in any rate of wind. Wait until a zero wind day or extremely light wind when learning how to fly. Replaceable Battery SYNCING YOUR AIR RACER™ 2.0 Important! When syncing your AIR RACER™ 2.0 with the controller always make sure that the drone is on a flat level surface and that your digital trim settings are in the center position. This insures that the 6 Axis gyro is properly programmed to respond to your trim settings. Your AIR RACER™ 2.0 Power On/Off utilizes an automatic 2.4G channel selection system that allows up to 8 people to fly side by side in the same wireless range with no interference. 1. Before starting, make sure that the power switch is off both on your controller and the AIR RACER™ 2.0. Infrared Receiver Make sure that there are no other 2.4G devices in the area. LED Light 2. Turn on your AIR RACER™ 2.0 and set it down on a flat level surface.The red and white LED lights of the drone should begin to flash repeatedly. Bottom View 3. Quickly turn ON the remote and you will notice that the red LED light on the face of the controller should light up and stay solid. The “Battle Indicator” will flash once then off . The lights on the drone will flash slower. CONTROLLER DIAGRAM 4. Push the left control stick all the way up until it stops and then pull it back all the way down to the bottom(see illustration below). You will hear 2 high-pitched beeps when pulling the throttle up and Blue Battle Indicator down. The lights on the drone should stop flashing and become solid. If the lights on both the drone and Power Indicator the controller have stopped flashing and become solid you have successfully synced your AIR RACER™ 2.0 Shoot button Stunt button and are ready to fly. If the lights on the controller or the drone are still flashing repeat steps 1-4 again. • TIP 1: try not to leave too much time between turning on the drone and the controller or your syncing window will time-out. Throttle Direction Control • TIP 2: Syncing your drone indoors or in the shade will make it easier to see the LED light indicators on both the controller and the drone. Low speed High speed Forward Trim Headless Mode Right Bank Trim OFF ON Backward Trim Calibrate Button Left Bank Trim Power On/Off move the control stick all the way the flashing red LED light will up and all the way down you become solid when you are 3 should hear a beep synced 4

FLIGHT CONTROL NOW YOU ARE READY TO FLY! If you have successfully synced your AIR RACER™ 2.0 to your controller as explained on page 4 you are now Below is a list of basic flight functions for your long-range remote to control the AIR RACER™ 2.0. While learning to fly your AIR RACER™ 2.0 it is best to start in a large space until you get used to the basic ready to fly. Before beginning to fly your drone you should familiarize yourself with how the controls work controls. As you master flying your AIR RACER™ 2.0 you can move to more advanced maneuvering so please carefully read and familiarize yourself with various control features explain in the next two pages. techniques. Practice makes perfect! Once again as a beginner pilot you should learn how to control your drone in a large open field or park on a day with zero or very light wind. Do not try to fly your AIR RACER™ 2.0 too high until you become a more H experience pilot. Move the left Throttle stick up to increase the propeller speed and the AIR RACER™ 2.0 will RECOGNIZING THE FRONT & REAR OF THE AIR RACER™ 2.0 accelerate and ascend. Even though the AIR RACER™ 2.0 has four rotors there is still a front or "forward" facing direction and Move the left Throttle stick down to decrease the "REAR" or backwards facing direction. The forward Front and forward facing direction of the AIR RACER™ propeller speed and the AIR RACER™ 2.0 will 2.0 is the side with two gray blades (see diagram G ). The rear and back of the Quadrocopter is the side with decelerate and descend (see diagram H). two black propellers (see diagram G). NOTE: The front of the Quadrocopter also displays WHITE LED light and the back of the Quadrocopter displays RED LED lights. While in the air, move the left Throttle stick left I FRONT and the AIR RACER™ 2.0 will rotate left. Move the left Throttle stick right and the AIR RACER™ 2.0 will rotate right (see diagram I). G J While in the air, move the right Direction Stick up and the AIR RACER™ 2.0 will move forward. REAR Move the right Direction Control down and the AIR RACER™ 2.0 will move backward (see diagram J). SPEED SELECT BUTTON The AIR RACER™ 2.0 has 2 speed settings; SLOW, and HIGH. The Default setting when you first turn on your AIR RACER™ 2.0 is the SLOW speed mode. To increase the speed simply press the Speed setting button (see remote diagram on pg 3) you will hear 2 beeps and the speed changed to HIGH speed. Speed settings can be set before flight or during the flight. While in the air, move the right Direction Control left K FRONT and the AIR RACER™ 2.0 will bank to the left. Move the right Direction Control right and the AIR HEADLESS MODE BUTTON RACER™ 2.0 will bank to the right (see diagram K). You can maintain orientation of your AIR RACER™ 2.0 during flight. REAR 1. Once the AIR RACER™ 2.0 is activated press the headless mode button (see controller on pg.3) to activate the internal compass. FLIGHT PRACTICE 2. The flying orientation is now locked to match the direction control lever. To master flying your aircraft try practicing the excersizes shown below. Start with simple vertical takeoffs, Note: Before switch to “headless Mode”,you need place the drone straight ahead right in front of you, landings, and left/right turning and rotating. Once those are mastered move on to square and cross Calibrate it first then press the headless mode button. maneuvers. Good luck and have fun! Fixed-point landing Square Pattern Maneuver Cross Pattern Maneuver 5 6

ADJUSTING THE TRIM CALIBRATING THE AIR RACER™ 2.0 NOTE: The AIR RACER™ 2.0 is already properly trimmed and calibrated right out of the box and should not NOTE: Your AIR RACER™ 2.0 comes pre-calibrated out of the box so you are ready to fly. require any trim adjustments before flying. Some more experienced pilots may want to adjust trim settings After several crashes and shock to your gyro sensors, you may notice that your drone is drifting and not for their style of flying. After several crashes you may need to adjust trim settings for the AIR RACER™ 2.0 holding its center position as well as it used to. to be more balanced. This most likely means that you need to recalibrate the 6 axis gyro. Please follow the simple instructions below. L 1. Place the AIR RACER™ 2.0 on a flat level surface. Forward/Backward Trim 2. Make sure the AIR RACER™ 2.0 is on and that the controller is synced (refer to syncing pg 4. ). Do not start • If your AIR RACER™ 2.0 drifts forward while in the the blades. Press the “calibrate button”. You will see the lights on the drone rapidly flash and stop. Once the air, push and release the BACKWARD TRIM button lights stop flashing you have completed your calibration and are ready to fly! repeatedly until the motion stops and proper flight is maintained (see diagram L). • If your AIR RACER™ 2.0 drifts backwards, push and TROUBLE SHOOTING: If you do not see the lights flash, turn off your controller take out the battery in the release the FORWARD TRIM button forward in Drone and Start again. Always make sure to put your battery in the copter first, then turn on your controller. the same manner until the problem is resolved. Push the left throttle stick up all the way and then pull back down all the way. When you hear the beep the AIR RACER™ 2.0 is synced to the controller and you are ready to calibrate. Bank Right/Left Trim M CALIBRATE BUTTON • If your AIR RACER™ 2.0 drifts left while in the air, push and release the RIGHT TRIM button repeatedly until the motion stops and proper flight is maintained (see diagram M). • If your AIR RACER™ 2.0 drifts right, push and release the LEFT TRIM button in the same manner until the problem is resolved. P INTERACTIVE BATTLE MODE Get ready for aerial combat missions with your friends (Note Requires additional AIR RACER™ 2.0). PREPARATION FOR MISSION: 1. Make sure all battling quadrocopters are fully charged, properly synced and ready to fly (refer to SYNCING YOUR AIR RACER™ 2.0). READY, AIM, FIRE! 1. While your AIR RACER™ 2.0’s in flight, aim the front side of your AIR RACER™ 2.0 to your opponent’s AIR RACER™ 2.0and press the SHOOT button on the top of your remote control (see diagram on pg 3). 2. If you score first hit, your opponent's remote control will vibrate one short time, the AIR RACER™ 2.0 will swing one time, in the mean time the indicator lights will flash one time. 3. If you score second hit, your opponent's remote control will vibrate two short times, the AIR RACER™ 2.0 will swing one time, in the mean time the indicator lights will flash two times. THREE STRIKES YOU'RE OUT! 4. On the third direct hit, your opponent's remote control will vibrate one long time, your opponent’s AIR RACER™ 2.0 indicator lights will flash three times and your opponent will not be able to control the quadrocopter. The quadrocopter will gradually descend to the ground. Mission accomplished! 5. Once the quadcopter fully stops, your opponent can pull the throttle all the way down to recover (reset) and will be ready for the next dogfight. 7 8

HOW TO PERFORM 360º STUNT FLIPS TROUBLESHOOTING YOUR AIR RACER™ 2.0 Performing 360º stunt flips with the AIR RACER™ 2.0 is as easy as 1-2-3: 1. Hover the AIR RACER™ 2.0 in still position making sure that you have at least 5 feet of clearance above PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION and below the quadrocopter,. 2. Press and release the 360˚ stunt button and you will enter the stunt flip mode the controller will start No Power 1. Power switched off 1. Switch the ON/OFF switch to ON beeping. (see diagram Q1). 2. Polarity is reversed 2. Make sure all batteries are installed 3. Determine which direction you want it to flip and quickly push the right control stick in the direction correctly (see diagram A on pg.2) you want to flip your AIR RACER™ 2.0 (see diagram Q2). You have 4 choices a) Forward flip, b) Backwards 3. Batteries may be low or in need of charging 3. Replace batteries flip, c) Right side flip, d) Left side flip. After stunt flip, it will automatically exit the stunt mode. 4. To exit the Stunt flip mode manually, simply Press and release the button again. The controller will stop 1. Remote is switched off 1. Switch the ON/OFF switch to ON beeping. Drone Not 2. battery power in remote is too weak 2.Connect the battery to AIR RACER™ 2.0 Responding 3. The remote is not properly synced 3. Re-sync the remote 4. Out of control range 4. Do not fly beyond 200 feet 360˚Stunt flip Button Q1 Q2 1. Rotor speed too slow 1. Push throttle lever forward Drone Won’t 2. Drone not fully charged 2. Recharge your AIR RACER™ 2.0 lift off 3. Obstruction of rotors 3. Check rotors for hair or other obstructions Drone Moving the throttle down too quickly Control the throttle slower, use auto land Decsends flying in high wind or bad weather feature, Do not fly in bad weather Too Fast REPLACING THE PROPELLER BLADES Your Battle X’s propeller system is a precision instrument that may need repair or replacement from time to time for optimal flight function. Crash landing at high-speed may cause damage to your Battle X’s propellers. 1. The AIR RACER™ 2.0 has four blades, two gray blades in the front, and two black blades in the back (see the diagram S). 2. When replacing the propeller blades, make sure to match both the color of the blade and the indication letter on the blade. 3. Replace the damaged blade with the correct blade. Front L R Gray Blade Front Left = L Gray Blade Front Right = R Black Blade Back Left = R Black Blade Back Right = L R L S 9 10

AIR RACER™ 2.0 WARNING: The AIR RACER™ 2.0 is designed for indoor & outdoor use. The Battle X’s blades revolve at high speeds and can cause damage to the user, spectators and animals. Stand away from the AIR RACER™ 2.0 to reduce the risk of getting into the flight path. Warn spectators that you will be flying your AIR RACER™ 2.0 so that they are aware of its position. Before flight, inspect the rotor blades to make sure that the blades are securely fastened to the AIR RACER™ 2.0. WARNING! Limited 90-Day Warranty NORTH AMERICA • Choking/Cutting Hazard. Small Parts/Sharp Rotor Blades. • Keep hands, hair and loose clothing away from the propeller when the power switch is turned to the AMAX Group USA warrants to the original consumer that this product is free from any ON position. electrical or mechanical defects for a period of 90 DAYS from the date of purchase. If any such • Turn off the transmitter and AIR RACER™ 2.0 power switches when not in use. • The included charger is built specifically for the AIR RACER™ 2.0 Li-Poly battery. Do not use it to charge defect is discovered within the warranty period, AMAX Group USA will repair or replace the any other battery. unit free of charge upon receipt of the unit, shipped postage prepaid and insured to our • New alkaline batteries are recommended for maximum performance. warranty center. The warranty covers normal consumer use and does not cover damage that • Parental supervision recommended when flying AIR RACER™ 2.0. occurs in shipment or failure that results from alterations, accident, misuse, abuse, neglect, wear and tear, inadequate maintenance, commercial use or unreasonable use of the unit. BATTERY WARNINGS Removal of any parts/components voids all warranties. This warranty does not cover cost of RECHARGEABLE BATTERY: repairs made or attempted outside by third-party individuals or companies. Any applicable This AIR RACER™ 2.0 uses a Li-Poly rechargeable battery. If battery no longer stays charged, dispose of implied warranties, including warranties of merchantability and fitness, are hereby limited to battery properly according to local disposal requirements. 90 DAYS from the date of purchase. Consequential or incidental damages resulting from a breach of any applicable express or implied warranties are hereby excluded. Some states do CONTROLLER BATTERIES: not allow limitations on the duration of implied warranties and do not allow exclusion of Remote control requires 3 “AA” batteries (not included). incidental or consequential damages, so the above limitations and exclusions in these Please read the important battery safety warning below. instances may not apply. • Do not mix alkaline, standard (carbon-zinc) and rechargeable batteries (Nickel Metal Hydride). • Do not mix old and new batteries. • Non-rechargeable batteries are not to be recharged. • Rechargeable batteries are to be removed from the item before being charged (if removable). REPAIR/REPLACE PRODUCT • Rechargeable batteries are only to be charged under adult supervision. If your product begins to malfunction or stop working, immediately email our warranty • Exhausted batteries should be removed immediately and must be recycled or disposed of properly center at the email listed below. If it is determined that a return is necessary, our warranty according to state or local government ordinances and regulations. department will issue you an RMA number/form and an address to the nearest return center • The supply terminals are not to be short-circuited. for shipping the product to. IMPORTANT NOTICE: We will reject all returns that are not • Only batteries of the same or equivalent type as recommended are to be used. accompanied by an issued RMA form and number so make sure to contact our warranty • Batteries are to be inserted with the correct polarity (see inside booklet for diagram). center before attempting to return your product! • Do not dispose batteries in a fire - batteries may leak or explode. PREPARATION FOR SHIPPING YOUR PRODUCT CARE AND MAINTENANCE Please repack your product in a durable box, preferably in the original carton, and send it • Always remove the batteries from the wireless remote control when it is not being used for an prepaid, and adequately insured. Include the RMA form that was issued by our warranty extended period of time. department along with your daytime telephone number and email address inside the • To clean, gently wipe the remote control and AIR RACER™ 2.0 with a clean damp cloth. shipping carton. If your warranty has expired, contact our warranty center for charged service. • Keep the toy away from direct heat or sunlight. For further information please send all inquiries to: customercare@amaxbrands.com • Do not submerge the toy into water. This can damage the unit beyond repair. • Parental guidance recommended when installing or replacing the batteries. IMPORTANT NOTICE! DO NOT ATTEMPT TO SHIP YOUR PRODUCT BACK WITHOUT FIRST CONTACTING OUR WARRANTY DEPARTMENT BY EMAIL AT: customercare@amaxbrands.com 11 12


Document Created: 2019-05-22 17:09:35
Document Modified: 2019-05-22 17:09:35
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC