Modular Approval Letter

FCC ID: 2ASEJ-ORROSWITCH01

Cover Letter(s)

Download: PDF
FCCID_4384307

                                          Edison Labs Inc. DBA Orro
                                         1875 S. Grant Street, Ste 620
                                            San Mateo, CA 94402




June 25, 2019

Federal Communications Commission
Office of Engineering and Technology
7435 Oakland Mills Road
Columbia, MD 21046

Subject: Limited Modular Approval Request

To whom it may concern:

This letter is to request Limited Modular Approval in accordance with FCC Rule Part 15.212(b) for the
certification request under FCC ID: 2ASEJ-ORROSWITCH01. This module is intended for integration
into devices constructed by the grantee.

Declaration of conditions.

    Y/N       15.212(a)(1) Condition


      Y       (i) The radio elements of the module have their own shielding. The physical crystal and tuning
              capacitors may be located external to the shielded radio elements


      Y       (ii) The module has buffered modulation/data inputs (if such inputs are provided) to ensure that
              the module will comply with part 15 requirements under conditions of excessive data rates or
              over-modulation.


      Y       (iii) The module has its own power supply regulation.


      Y       (iv) The module complies with the antenna and transmission system requirements of §§15.203,
              15.204(b) and 15.204(c). The antenna(s) are either permanently attached or employ a “unique”
              antenna coupler (at all connections between the module and the antenna, including the cable).


                                           Edison Labs Inc. DBA Orro
                                          1875 S. Grant Street, Ste 620
                                             San Mateo, CA 94402




      Y        (v) The module was tested in a stand-alone configuration, i.e., the module was not inside
               another device during testing for compliance with part 15 requirements. Unless the transmitter
               module will be battery powered, it complies with the AC line conducted requirements found in
               §15.207. AC or DC power lines and data input/output lines connected to the module do not
               contain ferrites, unless they will be marketed with the module (see §15.27(a)). The length of
               these lines was the length typical of actual use or, if that length is unknown, at least 10
               centimeters was used to insure that there is no coupling between the case of the module and
               supporting equipment. Any accessories, peripherals, or support equipment connected to the
               module during testing were unmodified and commercially available (see §15.31(i)).


      Y        (vi) The module is equipped with either a permanently affixed label or is capable of
               electronically displaying its FCC identification number.


      Y        (vii) The module complies with any specific rules or operating requirements that ordinarily
               apply to a complete transmitter and the applicant has provided adequate instructions along with
               the module to explain any such requirements.


      Y        (viii) The module complies with any applicable RF exposure requirements in its final
               configuration. The instructions provided with the module adequately explain any usage
               conditions or restrictions.




List of additional restrictions or conditions of use for this module.

 The antenna is not included on the module base. In accordance with KDB 996369, the approval
 becomes limited to hosts constructed according to manufacturer’s instructions.




Methods used to address restrictions to ensure compliance for all finished products.

 Module is for use in devices under direct control of the grantee.


                                         Edison Labs Inc. DBA Orro
                                        1875 S. Grant Street, Ste 620
                                           San Mateo, CA 94402




I acknowledge on behalf of the applicant that compliance of this module in all final configurations is the
responsibility of the applicant under the condition that the integrator follows all provided installation
instructions.



Sincerely,




Nima Banai
Head of Hardware Product
Edison Labs, Inc.
1875 S. Grant St.
Suite 620
San Mateo, CA 94402-9440
(415) 910-4296



Document Created: 2019-06-25 12:08:53
Document Modified: 2019-06-25 12:08:53

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC