Test report

FCC ID: 2ASBE-DEV00106

Test Report

Download: PDF
FCCID_4196702

Report No.: ATE20190037 Page 1 of 22 APPLICATION CERTIFICATION FCC Part 15C On Behalf of Ectosense NV Airpatch Charger Model No.: DEV00106 FCC ID: 2ASBE-DEV00106 Prepared for : Ectosense NV Address : Bosbessenlaan 19a, Rotselaar, 3110 Belgium Prepared by : Shenzhen Accurate Technology Co., Ltd. Address : 1/F., Building A, Changyuan New Material Port, Science & Industry Park, Nanshan District, Shenzhen, Guangdong, P.R. China Tel: +86-755-26503290 Fax: +86-755-26503396 Report No. : ATE20190037 Date of Test : January 14-January 16, 2019 Date of Report : January 18, 2019 FCC ID: 2ASBE-DEV00106 Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20190037 Page 2 of 22 TABLE OF CONTENTS Description Page Test Report Declaration 1. TEST RESULTS SUMMARY ......................................................................................................... 4 2. GENERAL INFORMATION .......................................................................................................... 5 2.1. Description of Device (EUT)....................................................................................................................5 2.2. Test Mode .................................................................................................................................................5 2.3. Special Accessory and Auxiliary Equipment ...........................................................................................5 2.4. Description of Test Facility ......................................................................................................................6 2.5. Measurement Uncertainty.........................................................................................................................6 3. MEASURING DEVICE AND TEST EQUIPMENT ..................................................................... 7 3.1. The Equipment Used to Measure Conducted Disturbance .......................................................................7 3.2. The Equipment Used to Measure Radiated Emission...............................................................................7 4. AC POWER LINE CONDUCTED MEASUREMENT................................................................. 8 4.1. Block Diagram of Test Setup....................................................................................................................8 4.2. AC Power Line Conducted Emission Measurement Limits .....................................................................8 4.3. Configuration of EUT on Measurement ...................................................................................................8 4.4. Operating Condition of EUT ....................................................................................................................8 4.5. Measurement Procedure ...........................................................................................................................9 4.6. Data Sample..............................................................................................................................................9 4.7. Measurement Results................................................................................................................................9 5. RADIATED EMISSION MEASUREMENT................................................................................ 14 5.1. Block Diagram of Test............................................................................................................................14 5.2. Radiated Emission Limit ........................................................................................................................15 5.3. EUT Configuration on Measurement .....................................................................................................15 5.4. Operating Condition of EUT ..................................................................................................................15 5.5. Measurement Procedure .........................................................................................................................15 5.6. Data Sample............................................................................................................................................16 5.7. Measurement Result ...............................................................................................................................16 6. ANTENNA REQUIREMENT........................................................................................................ 22 6.1. The Requirement ....................................................................................................................................22 6.2. Antenna Construction .............................................................................................................................22 FCC ID: 2ASBE-DEV00106 Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20190037 Page 3 of 22 Test Report Declaration Applicant : Ectosense NV Address : Bosbessenlaan 19a, Rotselaar, 3110 Belgium Manufacturer : Ectosense NV Address : Bosbessenlaan 19a, Rotselaar, 3110 Belgium Product : Airpatch Charger Model No. : DEV00106 Trade Mark : NightOwl Measurement Procedure Used: FCC CFR47 Part 18 Subpart C Section 18.305 and 18.307 ANSI C63.10: 2013 The device described above is tested by Shenzhen Accurate Technology Co., Ltd. to determine the maximum emission levels emanating from the device. The maximum emission levels are compared to the FCC Part 18 Subpart C limits both radiated and conducted emissions. The measurement results are contained in this test report and Shenzhen Accurate Technology Co., Ltd. is assumed full responsibility for the accuracy and completeness of these measurements. Also, this report shows that the Equipment Under Test (EUT) is to be technically compliant with the FCC requirements. This report applies to above tested sample only. This report shall not be reproduced in part without written approval of Shenzhen Accurate Technology Co., Ltd. Date of Test : January 14-January 16, 2019 Date of Report : January 18, 2019 Prepared by : (Star Yang, Engineer) Approved & Authorized Signer : (Sean Liu, Manager) FCC ID: 2ASBE-DEV00106 Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20190037 Page 4 of 22 1. TEST RESULTS SUMMARY Test Items Test Standard Test Results AC Power Line Conducted Emission FCC Part 18.307(b) Pass Radiated Emission FCC Part 18.305(b) Pass FCC ID: 2ASBE-DEV00106 Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20190037 Page 5 of 22 2. GENERAL INFORMATION 2.1.Description of Device (EUT) Product : Airpatch Charger Model No. : DEV00106 Frequency : 110-205KHz Modulation Type : ASK Type of Antenna : Induction coil AC Adapter Rating : Model: SWN6-5-NH-I38 Input: 100-240Vac, 0.6-0.3A, 50-60Hz Output: 5V 1.2A 2.2.Test Mode Test Item EMI Test Modes Conducted Emission Max. Power Output Radiated Emission Max. Power Output 2.3.Special Accessory and Auxiliary Equipment Description Manufacturer Model S/N Airpatch Sensor Ectosense NV DEV00093 N/A Note: Wireless charger load is provided by manufacturer FCC ID: 2ASBE-DEV00106 Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20190037 Page 6 of 22 2.4.Description of Test Facility EMC Lab : Recognition of accreditation by Federal Communications Commission (FCC) The Designation Number is CN1189 The Registration Number is 708358 Listed by Innovation, Science and Economic Development Canada (ISEDC) The Registration Number is 5077A-2 Accredited by China National Accreditation Service for Conformity Assessment (CNAS) The Registration Number is CNAS L3193 Accredited by American Association for Laboratory Accreditation (A2LA) The Certificate Number is 4297.01 Name of Firm : Shenzhen Accurate Technology Co., Ltd Site Location : 1/F., Building A, Changyuan New Material Port, Science & Industry Park, Nanshan District, Shenzhen, Guangdong, P.R. China 2.5.Measurement Uncertainty Conducted emission expanded uncertainty : U=2.23dB, k=2 Radiated emission expanded uncertainty : U=3.08dB, k=2 (9kHz-30MHz) Radiated emission expanded uncertainty : U=4.42dB, k=2 (30MHz-1000MHz) Radiated emission expanded uncertainty : U=4.06dB, k=2 (Above 1GHz) FCC ID: 2ASBE-DEV00106 Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20190037 Page 7 of 22 3. MEASURING DEVICE AND TEST EQUIPMENT 3.1. The Equipment Used to Measure Conducted Disturbance Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 1. Test Receiver Rohde & Schwarz ESCS30 100307 Jan.05, 2019 1 Year 2. L.I.S.N. Schwarzbeck NLSK8126 8126431 Jan.05, 2019 1 Year 3. Pulse Limiter Rohde & Schwarz ESH3-Z2 100305 Jan.05, 2019 1 Year 50Ω Coaxial Anritsu Corp MP59B 6200283936 Jan.05, 2019 1 Year 4. Switch 5. RF Coaxial Cable SUHNER N-2m No.2 Jan.05, 2019 1 Year 6. Measurement Software: ES-K1 V1.71 3.2. The Equipment Used to Measure Radiated Emission Item Equipment Manufacturer Model No. Serial No. Last Cal. Cal. Interval 1. Spectrum Analyzer Rohde&Schwarz FSV40 101495 Jan.05, 2019 1 Year 2. Test Receiver Rohde& Schwarz ESR 101817 Jan.05, 2019 1 Year 3. Bilog Antenna Schwarzbeck VULB9163 9163-323 Jan.05, 2019 1 Year 4. Loop Antenna Schwarzbeck FMZB1516 1516131 Jan.05, 2019 1 Year 5. Horn Antenna Schwarzbeck BBHA9120D 9120D-655 Jan.05, 2019 1 Year 6. Horn Antenna Schwarzbeck BBHA9170 9170-359 Jan.05, 2019 1 Year 7. RF Switching Compliance RSU-M2 38322 Jan.05, 2019 1 Year Unit+PreAMP Direction 8. Pre-Amplifier Agilent 8447D 294A10619 Jan.05, 2019 1 Year 9. Pre-Amplifier Rohde&Schwarz CBLU11835 3791 Jan.05, 2019 1 Year 40-01 10. 50 Coaxial Switch Anritsu Corp MP59B 6200506474 Jan.05, 2019 1 Year 11. RF Coaxial Cable RESENBERGER N-12m No.11 Jan.05, 2019 1 Year 12. RF Coaxial Cable RESENBERGER N-0.5m No.12 Jan.05, 2019 1 Year 13. RF Coaxial Cable SUHNER N-2m No.13 Jan.05, 2019 1 Year 14. RF Coaxial Cable SUHNER N-0.5m No.15 Jan.05, 2019 1 Year 15. RF Coaxial Cable SUHNER N-2m No.16 Jan.05, 2019 1 Year 16. RF Coaxial Cable RESENBERGER N-6m No.17 Jan.05, 2019 1 Year 17. Measurement Software: EZ_EMC V1.1.4.2 FCC ID: 2ASBE-DEV00106 Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20190037 Page 8 of 22 4. AC POWER LINE CONDUCTED MEASUREMENT 4.1.Block Diagram of Test Setup Test Receiver AC Mains L.I.S.N Adapter LOAD EUT 4.2.AC Power Line Conducted Emission Measurement Limits Frequency Limit dB(V) (MHz) Quasi-peak Level Average Level 0.15 - 0.50 66.0 – 56.0 * 56.0 – 46.0 * 0.50 - 5.00 56.0 46.0 5.00 - 30.00 60.0 50.0 NOTE1: The lower limit shall apply at the transition frequencies. NOTE2: The limit decreases linearly with the logarithm of the frequency in the range 0.15MHz to 0.50MHz. 4.3.Configuration of EUT on Measurement The equipments are installed on conducted emission measurement to meet the commission requirement and operating regulations in a manner, which tends to maximize its emission characteristics in a normal application. 4.4.Operating Condition of EUT 4.4.1. Setup the EUT and simulator as shown as Section 4.1. 4.4.2. Turn on the power of all equipment. 4.4.3. Let the EUT work in test mode and measure it. FCC ID: 2ASBE-DEV00106 Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20190037 Page 9 of 22 4.5.Measurement Procedure The EUT is put on the plane 0.8 m high above the ground by insulating support and is connected to the power mains through a line impedance stabilization network (L.I.S.N.). This provides a 50ohm coupling impedance for the EUT system. Please refer the block diagram of the test setup and photographs. Both sides of AC lines are checked to find out the maximum conducted emission. In order to find the maximum emission levels, the relative positions of equipment and all of the interface cables shall be changed according to ANSI C63.10: 2013 on Conducted Emission Measurement. The bandwidth of test receiver (R & S ESCS30) is set at 9kHz. The frequency range from 150kHz to 30MHz is checked. 4.6.Data Sample Frequency Transducer QuasiPeak Average QuasiPeak Average QuasiPeak Average Remark (MHz) value Level Level Limit Limit Margin Margin (Pass/Fail) (dB) (dBV) (dBV) (dBV) (dBV) (dB) (dB) X.XX 10.6 25.3 17.0 59.0 49.0 33.7 32.0 Pass Transducer value = Insertion loss of LISN + Cable Loss Result = Quasi-peak Level/Average Level + Transducer value Limit = Limit stated in standard Calculation Formula: Margin = Limit – Reading level value – Transducer value 4.7.Measurement Results Pass. The frequency range from 150kHz to 30MHz is checked. Emissions attenuated more than 20 dB below the permissible value are not reported. The spectral diagrams are attached as below. FCC ID: 2ASBE-DEV00106 Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20190037 Page 10 of 22 FCC ID: 2ASBE-DEV00106 Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20190037 Page 11 of 22 FCC ID: 2ASBE-DEV00106 Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20190037 Page 12 of 22 FCC ID: 2ASBE-DEV00106 Shenzhen Accurate Technology Co., Ltd

ACCURATE TECHNOLOGY CO.,LTD CONDUCTED EMISSION STANDARD FCC PART 18 C EUT: Airpatch Charger M/N:DEVOO106 Manufacturer: Ectosense NV Operating Condition: Max. Power Output Test Site: 1#¥Shielding Roon Operator: Frank Test Specification: L 120V/60Hz Comment: Report NO.:ATE20190037 Start of Test: 2019—1—14 / 10:02:;15MM SCAN TABLE: "V S9K—30MHz fin" Short Description: _SUB_STD_VTERMZ 1.70 Start Stop Step Detector Meas. 1 Transducer Frequency Frequency Width Time Bandw. 9.0 kiz 150.0 kHz 100.0 Hz QuasiPeak 1.0 s 200 Hz NSLKS126 2008 Average 150.0 kEz 30.0 MBz 5.0 kHz QuasiPeak 1.0 s 9 kEz NSLK8126 2008 Average Level [dBpV) g__ g!— ol _ sl— Sl— o 150k 200k 400k 600k_ 800k 1 t = & & 5 a 5 a & 5 = s = & 8 5 Frequency [H2] m m n m n y MEASUREMENT RESULT: "FP—1198—4_fin" 2019—1—14 10:05AM Frequency Level Transd Limit Margin Detector Line PE MEz dBuV ds dBuv dB 0.340018 39.20 10.6 59 20.0 P L1 GND 0. 670245 41.90 10.8 56 14.1 P L1 GND 0.941021 41.00 10.8 56 15.0 9P L1 GND 4.932760 41 .50 11.2 56 14.5 P L1 GND 5.300255 43.30 11.2 60 16.7 (gP L1 GND 17.766905 45 .20 11.4 60 14.8 P L1 GND MEASUREMENT RESULT: "F—1198—4fin2" 2019—1—14 10:05MM Frequency Level Transd Limit Margin Detector Line PE MEz dBuV dB dBuv dB 0. 341378 31.70 10. 6 49 17.5 AV L1 GND 0. 654382 33. 60 10.8 46 12.4 AV L1 GND 1.015172 32.60 10.8 46 13.4 AV L1 GND 4.992190 33.20 11.2 46 12.8 AV L1 GND 5.300255 34 .80 11.2 50 15.2 AV L1 GND 17.766905 39. 60 11.4 50 10.4 AV L1 GND

Report No.: ATE20190037 Page 14 of 22 5. RADIATED EMISSION MEASUREMENT 5.1.Block Diagram of Test 5.1.1.Block diagram of connection between the EUT and simulators AC Mains Adapter LOAD EUT 5.1.2.Block diagram of test setup (In chamber) FCC ID: 2ASBE-DEV00106 Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20190037 Page 15 of 22 5.2.Radiated Emission Limit Frequency Distance Field Strengths Limit MHz Meters V/m dBV/m 0.009-30 300 15 103.5 30-88 3 100 40.0 88-216 3 150 43.5 216-960 3 200 46.0 Above 960 3 500 54.0 Limit: 0.009-30MHz = 20log (15) +40log (300/3) dBV/m Distance Correction Factor=40log(test distance/specific distance) 5.3.EUT Configuration on Measurement The equipments are installed on Radiated Emission Measurement to meet the commission requirements and operating regulations in a manner which tends to maximize its emission characteristics in normal application. 5.4.Operating Condition of EUT 5.4.1. Setup the EUT and simulator as shown as Section 5.1. 5.4.2. Turn on the power of all equipment. 5.4.3. Let the EUT work in test mode and measure it. 5.5.Measurement Procedure The EUT and its simulators are placed on a turntable, which is 0.8 meter high above ground. The turntable can rotate 360 degrees to determine the position of the maximum emission level. EUT is set 3.0 meters away from the receiving antenna, which is mounted on an antenna tower. The antenna can be moved up and down between 1.0 meter and 4 meters to find out the maximum emission level. Broadband antenna (calibrated bilog antenna) is used as receiving antenna. Both horizontal and vertical polarizations of the antenna are set on measurement. In order to find the maximum emission levels, all of the interface cables must be manipulated according to ANSI C63.10: 2013 on radiated emission measurement. From 9kHz to 30MHz at distance 3m The EUT was rotated a full revolution in order to obtain the maximum value of the electric field intensity. The final level, expressed in dBuV/m, is arrived at by taking the reading from the EMI receiver(Level dBuV) and adding the antenna correction factor and cable loss factor(Factor dB) to it. This result then has to be compared with the relevant FCC limit.The resolution bandwidth during the measurement is as follows: 9kHz – 150kHz: ResBW: 200Hz 150kHz – 30MHz: ResBW: 9kHz FCC ID: 2ASBE-DEV00106 Shenzhen Accurate Technology Co., Ltd

Report No.: ATE20190037 Page 16 of 22 5.6.Data Sample Frequency( Reading Factor Result Limit Margin Remark MHz) (dBv) (dB/m) (dBv/m) (dBv/m) (dB) X.XX 49.83 -22.03 27.80 43.50 -15.70 QP Frequency(MHz) = Emission frequency in MHz Reading(dBv) = Uncorrected Analyzer/Receiver reading Factor (dB/m)= Antenna factor + Cable Loss – Amplifier gain Result(dBv/m) = Reading + Factor Limit (dBv/m)= Limit stated in standard Calculation Formula: Margin(dB) = Result (dBv/m)–Limit(dBv/m) Result(dBv/m)= Reading(dBv)+ Factor(dB/m) The “Margin” column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of -7dB means the emission is 7dB below the limit. 5.7.Measurement Result Pass. Note: 185KHz is fundamental frequency. Emissions attenuated more than 20 dB below the permissible value are not reported. The spectrum analyzer plots are attached as below. EUT test at X,Y,Z position, Measured at Antenna position 0 degree and 90 degree, only worse case is reported. FCC ID: 2ASBE-DEV00106 Shenzhen Accurate Technology Co., Ltd

ACCURATE TECHNOLOGY CO., LTD RADIATED EMISSION STANDARD FCC PART 18 C EUT: Airpatch Charger M/N:DEVOOLOG Manufacturer: Ectosense NV Operating Condition: Max. Power Output Test Site: 1#Shielding Room Operator: Frank Test Specification: AC 120¥/608z Comment: X Start of Test: 2019—1—16 / 18:02:02 SCAN TABLE: "LFRE(E) Fin" Short Description: _SUB_STD_VTERM2 1.70 Start Stop Step Detector Meas. IF Transducer Frequency Frequency Width Time Bandw. 9.0 kHz 150.0 kHz 100.0 Hz QuasiPeak 1 200 Hz 15168 150.0 kHz 30.0 MHz 5.0 kHz QuasiPeak 1 9 kHz 1516R Level [dBpV/m] 110 100 80 60 ao 20 k 20k— 30k 50k 70k 100k 200k 300k 500k 1M 2M 3M 4M 6M 10M 30M Frequency [H2] x x cuzs 37—15_fin ues 37—15_pre e 17M 18e Voltage AV MEASUREMENT RESULT: "FC—0037—15fin" 2019—1—16 10:48 Frequency Level Transd Limit Margin Det. Height Azimuth Polarization MEz Bu¥/m ds dbuV/m dB on deg 0.035000 40.10 20.1 103.5 63.4 QP 100.0 0.00 404 M D4 BX M 0.061000 28.20 20.1 103.5 75.3 QP 100.0 0.00 0.063000 35.70 20.1 103.5 67.8 P 100.0 0.00 0.090200 45.20 20.1 103.5 58.3 QP 100.0 0.00 0.150000 45.10 20.1 103.5 58.4 QP 100.0 0.00 0.185000 70.04 20.2 103.5 $5.5 9f 100 .0 0.00

ACCURATE TECHNOLOGY CO., LTD RADIATED EMISSION STANDARD FCC PART 18 C EUT: Airpatch Charger M/N: DEVO0106 Manufacturer: Ectosense NV Operating Condition: Max. Power Output Test Site: l#Shielding Room Operator: Frank Test Specification: AC 120V/60Hz2 Comment: 3 Start of Test: 2019—1—16 / 18102:02 SCAN TABLE: "LFRE(E) Fin" Short Description: _SUB_STD_VITERM2 1.70 Start Stop Step Detector Meas. IF Transducer Frequency Frequency Width Time Bandvw. 9.0 kHz 150.0 kHz 100.0 Hz QuasiPeak 1.0 s 200 Hz 15162 150.0 kHz 30.0 MHz 5.0 kBz QuasiPeak 1.0 s 9 kHz 15168 Lovel [dBpV/m] 110 100 80 60 40 20 10 Ok 20k 30k 50k 70k 100k 200k 300k 500k 1M 2M 3M 4M 6M 10M 30M Frequency [Hz] Voltage AV MEASUREMENT RESULT: "FC—0037—16_fin" 2019—1—16 10150 Frequency Level Transd Limit Margin Det. Eeight Azimuth Polarization MBz dBuV/m db dBuV/m dB cm deg 0.031400 38.40 29.1 103.5 65.1 oPf 100.0 0.00 Y 0.035000 39.60 20.1 103.5 §3.9 QP 100.0 0.00 ~v 63000 35.80 20.1 103.5 67.17 oP 100.0 0.00 x¥ 0.094400 34.10 20.1 103.5 68.8 Qr 100.0 0.00 % 0.150000 40.30 20.1 103.5 63.2 QP 100.0 0.00 °¥ 0.185000 67.90 20.2 103.5 35.6 QP 100.0 0.00— %

ACCURATE TECHNOLOGY CO., LTD RADIATED EMISSION STANDARD FCC PART 18 C EUT: Airpatch Charger M/N:DEVOO106 Manufacturer: Ectosense NV Operating Condition: Max. Power Output Test Site: 1#Shielding Room Operator: Frank Test Specification: AC 120v/608z Comment: 2 Start of Test: 2019—1—16 / 18102:07 SCAN TABLE: "LERE(E) Fin" Short Description: _SUB_STD_VTERMZ 1.70 Start Stop Step Detector Meas. IF Transducer Frequency Frequency Width Time Bandw. 9.0 kiz 150.0 kHz 100.0 Hz QuasiPeak 0 s 200 Hz 15168 150.0 kBz 30.0 MHz 5.0 k8z QuasiPeak 1.0 s 9 kBz 1516E Level [dBpV/im] 110 100 80 60 40 20 0 O 20k 30k 50k 70k 100k 200k 300k 500k 1M 2M 3M 4M 6M 10M 30M Frequency [Hz] x x iMes ues mm II34 Voltag a MEASUREMENT RESULT: "FR—0037—2_fin" 2019—1—16 10:51 Frequency Level Transd Limit Margin Det. Height Azimuth Polarization MHz dBuV/m dB dBuV/m dB cm deg 0.015600 43.40 20.1 103.5 60.1 QP 100.0 0.00 ba ba ty bu ba ba 0.031200 42.40 20.1 103.5 61.1 P 100.0 0.00 0.046600 48.40 20.1 103.5 55.1 QP 100.0 0.00 0.062200 45.20 20.1 103.5 58.3 QP 100.0 0.00 0.078600 42.30 20.1 103.5 61.2 QP 100.0 0.00 0.185000 68.70 20—2 103.5 34.8 QP 100.0 0.00

o ACCURATE TECHNOLOGY CO., LTD. Site: 1# Chamber F1,Bldg.A, Changyuan New Material Port Keyuan Rd, Tel:+86—0755—26503290 Science & Industry Park,Nanshan Shenzhen,P.R.China Fax:+86—0755—26503396 Job No.: STAR2018 #577 Polarization: Horizontal Standard: FCC Part 18C 3M Radiated Power Source: AC 120V/60Hz Test item: Radiation Test Date: 2019/01/16 Temp.( C)/Hum.(%) 25 C/55% Time: 17:15:22 EUT: Airpatch Charger Engineer Signature: star Mode: Max power output Distance: 3m Model: DEVO0106 Manufacturer: Ectosense NV Note: Report No.:ATE20190037 70.0 dBu¥/m limit1 : — limit2; — 60 50 40 30 20 10 0.0 ; } ; | ( ; 30.000 l‘[l 50 6O ?l] 80 éUU ;U[I 500 l%UU ;"U[l 1000.0 MHz No. (';/rlf-g) (5533'23) F(cai'ést;j" (dFéif/”/'fin (dém}m) w:erg)m petecter ETY 50377 Remork 1 777407| 4086 2754 i33z 40.00 |26.68) ap 200 301 2 sa3i31| di8ge 2746 1442 4350 |29.08) ap 200 4s 3 i2i8809] sa265 2749 256 4350 |—1834) ap 200 105 4 1447809 4976 2605 2171 4350 2170 ap 200 222 5 ris3616)| 4187 —24.05 1982 4350 2368 ap 200 256 6 si8go875s) 4119 —20.68 2051 46.00 25.49) ap 200 125

ACCURATE TECHNOLOGY CO., LTD. Site: 1# Chamber F1,Bldg.A,Changyuan New Material Port Keyuan Rd, Tel:+86—0755—26503290 Science & Industry Park, Nanshan Shenzhen,P.R.China Fax:+86—0755—26503306 Job No.: STAR2018 #578 Polarization: Vertical Standard: FCC Part 18C 3M Radiated Power Source: AC 120V/60Hz Test item: Radiation Test Date: 2019/01/16 Temp.(_ C)/Hum.(%) 25 C/55 % Time: 17:16:38 EUT: Airpatch Charger Engineer Signature: star Mode: Max power output Distance: 3m Model: DEVOO106 Manufacturer: Ectosense NV Note: Report No.:ATE20190037 70.0 dBu¥/m } Himit1: «—— Himit2: — n s 50 40 30 gg 52210032001 @E 0 BM L200 00@ 10000 20000d 0000000b ds 10 0.0 4 ] H H 1| 30.000 40 5o 60 70 80 300 400 500 600 700 1000.0 MHz Freq. Reading Factor Result Limit [Margin Height Degree No— (viHz) (dBuvim) (dB) (dBuvim)| (dBuvim)| (dBy °4*| (m) (deg) RP®* 1 62.3038) 44.13 —27.25 16.88 40.00 |—23.12] QP 100 68 2 97.0023) 4549 —27.66 17.83 43.50 |—25.67| QP 100 100 3 120.6118| 51.79 —27.46 24.33 43.50 |—19.17| QP 100 125 4 177.5179| 46.42 —26.26 20.16 43.50 |—23.34| QP 100 140 § 245.2606| 41.73 —23.67 18.06 46.00 |—27.94| QP 100 108 6 466.5230) 40.54 —16.81 23.73 46.00 |—22.27| QP 100 224

Report No.: ATE20190037 Page 22 of 22 6. ANTENNA REQUIREMENT 6.1.The Requirement According to Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. 6.2.Antenna Construction Device is equipped with permanent attached antenna, which isn’t displaced by other antenna. Therefore, the equipment complies with the antenna requirement of Section 15.203. Induction coil ***** End of Test Report ***** FCC ID: 2ASBE-DEV00106 Shenzhen Accurate Technology Co., Ltd


Document Created: 2019-03-11 18:46:12
Document Modified: 2019-03-11 18:46:12
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC