Test reports

FCC ID: 2AS8H-HP3090

Test Report

Download: PDF
FCCID_4319697

Page 1 of 24 Report No.: HK1905201074-E FCC RADIO TEST REPORT FCC ID: 2AS8H-HP3090 Product： Wireless TV Headphones Trade Name： RCA Model Name： HP3090 Report No.： HK1905201074-E Prepared for Number One Commerce Co., LTD Room 1635, 16/F., Metro Centre 2, 21 Lam Hing Street, Kowloon Bay, Hong Kong, China Prepared by Shenzhen HUAK Testing Technology Co., Ltd. 1F, B2 Building, Junfeng Zhongcheng Zhizao Innovation Park, Heping Community, Fuhai Street, Bao'an District, Shenzhen, China

Page 2 of 24 Report No.: HK1905201074-E TEST RESULT CERTIFICATION Applicant’s name ................. : Number One Commerce Co., LTD Room 1635, 16/F., Metro Centre 2, 21 Lam Hing Street, Address .................................. : Kowloon Bay, Hong Kong, China Manufacture's Name ............ : Number One Commerce Co., LTD Room 1635, 16/F., Metro Centre 2, 21 Lam Hing Street, Address .................................. : Kowloon Bay, Hong Kong, China Product description Product name ........................... : Wireless TV Headphones Trade Mark ............................. : RCA Model and/or type reference : HP3090 FCC Rules and Regulations Part 15 Subpart C Section 15.249 Standards .............................. : ANSI C63.10: 2013 This device described above has been tested by Shenzhen HUAK Testing Technology Co., Ltd., and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of UNI, this document may be altered or revised by Shenzhen HUAK Testing Technology Co., Ltd., personnel only, and shall be noted in the revision of the document. Date of Test ............................................: Date (s) of performance of tests..............: May 22, 2019 – May 28, 2019 Date of Issue ...........................................: May 29, 2019 Test Result ...............................................: Pass Testing Engineer : (Gary Qian) Technical Manager : (Eden Hu) Authorized Signatory : (Jason Zhou)

Page 3 of 24 Report No.: HK1905201074-E Table of Contents Page 1 TEST SUMMARY 4 2 GENERAL INFORMATION 5 2.1 GENERAL DESCRIPTION OF EUT 5 2.2 Carrier Frequency of Channels 6 2.3 Operation of EUT during testing 6 2.4 DESCRIPTION OF TEST SETUP 6 2.5 MEASUREMENT INSTRUMENTS LIST 7 3 CONDUCTED EMISSION TEST 8 3.1 Test Limit 8 3.2 Test Setup 8 3.3 Test Procedure 8 3.4 Test Result 8 4 RADIATED EMISSION TEST 11 4.1 Test Limit 11 4.2 Test Setup 12 4.3 Test Procedure 14 4.4 Test Result 14 5 OCCUPIED BANDWIDTH TEST 19 5.1 Test Setup 19 5.2 Rules and specifications 19 5.3 Test Procedure 19 5.4 Test Result 20 6 ANTENNA REQUIREMENT 22 7 PHOTOGRAPH OF TEST 23 7.1 Radiated Emission 23 7.2 Conducted Emission 24

Page 4 of 24 Report No.: HK1905201074-E 1 TEST SUMMARY 1.1 TEST PROCEDURES AND RESULTS DESCRIPTION OF TEST RESULT AC Power Line Conducted Emission COMPLIANT Field Strength of Fundamental COMPLIANT Spurious Emissions COMPLIANT Band Edge COMPLIANT 20dB Occupied Bandwidth COMPLIANT Antenna requirement COMPLIANT 1.2 TEST FACILITY Test Firm : Shenzhen HUAK Testing Technology Co., Ltd. Address : 1/F., Building B2, Junfeng Zhongcheng Zhizao Innovation Park, Heping Community, Fuhai Street, Bao'an District, Shenzhen, Guangdong, China The testing quality ability of our laboratory meet with "Quality Law of People's Republic of China" Clause 19.The testing quality system of our laboratory meets with ISO/IEC-17025 requirements, which is approved by CNAS. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: CNAS-LAB Code: L9589 The EMC Laboratory has been assessed and in compliance with CNAS-CL01 accreditation criteria for testing Laboratories (identical to ISO/IEC 17025:2017 General Requirements) for the Competence of testing Laboratories. Designation Number: CN1229 Test Firm Registration Number: 616276 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. 1.3 MEASUREMENT UNCERTAINTY Measurement Uncertainty Conducted Emission Expanded Uncertainty = 2.23dB, k=2 Radiated emission expanded uncertainty(9kHz-30MHz) = 3.08dB, k=2 Radiated emission expanded uncertainty(30MHz-1000MHz) = 4.42dB, k=2 Radiated emission expanded uncertainty(Above 1GHz) = 4.06dB, k=2

Page 5 of 24 Report No.: HK1905201074-E 2 GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF EUT Equipment Wireless TV Headphones Trade Mark RCA Model Name HP3090 Serial Model / Model Difference / FCC ID 2AS8H-HP3090 Antenna Type PCB Antenna Antenna Gain 0dBi Operation frequency 912MHz, 912.5MHz, 913MHz Number of Channels 3CH Modulation Type ASK Battery N/A Power Source DC 5V 0.55A From AC Adapter Model:YLJXA-T05055 Adapter Information Input:AC100-240, 50/60Hz, 0.5A MAX Output:DC5V 0.55A

Page 6 of 24 Report No.: HK1905201074-E 2.2 Carrier Frequency of Channels Operation Frequency each of channel Channel Frequency 01 912MHz 02 912.5MHz 03 913MHz 2.3 Operation of EUT during testing Operating Mode The mode is used: Transmitting mode 2.4 DESCRIPTION OF TEST SETUP Operation of Radiated Emission EUT during testing: EUT Headphones AC 120V, 60Hz AC Adapter Operation of EUT during Conducted testing: EUT Headphones AC 120V, 60Hz AC Adapter Operation of EUT during Above1GHz Radiation testing: EUT AC 120V, 60Hz AC Adapter Table for auxiliary equipment: Equipment Description Manufacturer Model Calibration Due Date Headphones RCA HP3090 N/A

Page 7 of 24 Report No.: HK1905201074-E 2.5 MEASUREMENT INSTRUMENTS LIST Item Equipment Manufacturer Model No. Serial No. Calibrated until CONDUCTED EMISSIONS TEST 1 LISN R&S ENV216 HKE-002 2019.12.27 2 LISN R&S ENV216 HKE-029 2019.12.27 3 EMI Test Receiver R&S ESCI-7 HKE-010 2019.12.27 RADIATED EMISSION TEST 1 Broadband antenna Schwarzbeck VULB 9163 HKE-012 201912.27 2 Horn antenna Schwarzbeck 9120D HKE-013 2019.12.27 3 Receiver R&S ESCI 7 HKE-010 2019.12.27 4 Position controller Taiwan MF MF7802 HKE-011 201912.27 5 Preamplifier EMCI EMC051845SE HKE-015 2019.12.27 6 Preamplifier Agilent 83051A HKE-016 2019.12.27 7 High pass filter unit Tonscend JS0806-F HKE-055 2019.12.27 8 Spectrum analyzer Agilent N9020A HKE-048 2019.12.27 9 Spectrum analyzer Agilent N9020A HKE-048 2019.12.27 10 Signal generator Agilent 83630A HKE-028 2019.12.27 11 Signal generator Agilent N5182A HKE-029 2019.12.27 RF automatic control 12 Tonscend JS0806-2 HKE-060 2019.12.27 unit 13 Power meter Agilent E4419B HKE-085 2019.12.27

Page 8 of 24 Report No.: HK1905201074-E 3 CONDUCTED EMISSION TEST 3.1 Test Limit For unintentional device, according to § 15.107(a) Line Conducted Emission Limits is as following Maximum RF Line Voltage(dBV) Frequency CLASS A CLASS B (MHz) Q.P. Ave. Q.P. Ave. 0.15~0.50 79 66 66~56* 56~46* 0.50~5.00 73 60 56 46 5.00~30.0 73 60 60 50 * Decreasing linearly with the logarithm of the frequency For intentional device, according to §15.207(a) Line Conducted Emission Limit is same as above table. 3.2 Test Setup 3.3 Test Procedure 1. The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. A wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.10. 2. Support equipment, if needed, was placed as per ANSI C63.10. 3. All I/O cables were positioned to simulate typical actual usage as per ANSI C63.10. 4. If a EUT received DC power from the USB Port of Notebook PC, the PC’s adapter received AC120V/60Hz power through a Line Impedance Stabilization Network (LISN) which supplied power source and was grounded to the ground plane. 5. All support equipments received AC power from a second LISN, if any. 6. The EUT test program was started. Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver. 7. Analyzer/Receiver scanned from 150 KHz to 30MHz for emissions in each of the test modes. 3.4 Test Result Pass All the test modes completed for test. only the worst result of of AC120V/60Hz (High Channel ) was reported as below:

Page 9 of 24 Report No.: HK1905201074-E Test Specification: Line Remark: Transd = Cable lose + Antenna factor - Pre-amplifier; Margin = Limit – Level

Page 10 of 24 Report No.: HK1905201074-E Test Specification: Neutral Remark: Transd = Cable lose + Antenna factor - Pre-amplifier; Margin = Limit – Level

Page 11 of 24 Report No.: HK1905201074-E 4 RADIATED EMISSION TEST 4.1 Test Limit 1. Limit (Field strength of the fundamental signal): Frequency Limit(dBuV/m@3m) Remark 94.00 Average Value 902MHz-928MHz 114.00 Peak Value 2. Limit (Spurious Emissions): Frequency Limit(dBuV/m@3m) Remark 0.009-0.490 2400/F(KHz) Quasi-peak Value 0.490-1.705 24000/F(KHz) Quasi-peak Value 1.705-30 30 Quasi-peak Value 30MHz-88MHz 40.0 Quasi-peak Value 88MHz-216MHz 43.5 Quasi-peak Value 216MHz-960MHz 46.0 Quasi-peak Value 960MHz-1GHz 54.0 Quasi-peak Value 54.0 Average Value Above 1GHz 74.0 Peak Value 3. Limit (Band edge): Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in Section 15.209, whichever is the lesser attenuation.

Page 12 of 24 Report No.: HK1905201074-E 4.2 Test Setup 1. Radiated Emission Test-Up Frequency Below 30MHz 2. Radiated Emission Test-Up Frequency 30MHz~1GHz

Page 13 of 24 Report No.: HK1905201074-E 3. Radiated Emission Test-Up Frequency Above 1GHz 4. Receiver Setup: Frequency Detector RBW VBW Remark 9kHz- 150kHz Quasi-peak 200Hz 1kHz Quasi-peak Value 150kHz-30MHz Quasi-peak 9kHz 30kHz Quasi-peak Value 30MHz-1GHz Quasi-peak 120kHz 300kHz Quasi-peak Value Peak 1MHz 3MHz Peak Value Above 1GHz Peak 1MHz 10Hz Average Value

Page 14 of 24 Report No.: HK1905201074-E 4.3 Test Procedure 1. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter chamber in below 1GHz, 1.5m above the ground in above 1GHz. The table was rotated 360 degrees to determine the position of the highest radiation. 2. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. 3. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. 4. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. 5. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. 6. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. 4.4 Test Result Field Strength of Fundamental: Limits Frequency Emission PK/AV Ant. Pol. PK/AV Margin (dB) (MHz) (dBuV/m) (dBuV/m) 912 93.18(PK) H 114/94 -20.82 912 82.22(AV) H 114/94 -11.78 912.5 95.17(PK) H 114/94 -18.83 912.5 86.28(AV) H 114/94 -7.72 913 96.39(PK) H 114/94 -17.61 913 82.37(AV) H 114/94 -11.63 912 95.98(PK) V 114/94 -18.02 912 83.29(AV) V 114/94 -10.71 912.5 94.17(PK) V 114/94 -19.83 912.5 83.18(AV) V 114/94 -10.82 913 96.22(PK) V 114/94 -17.78 913 85.44(AV) V 114/94 -8.56 Spurious Emissions: For 9 kHz-30MHz Test Results: Note: The emission levels are 20 dB below the limit value, which are not reported. It is deemed to comply with the requirement.

Page 15 of 24 Report No.: HK1905201074-E For 30MHz-1GHz Test Results: Temperature: 22℃ Relative Humidity: 46% Test Date: May 27, 2019 Pressure: 1010hPa Test Voltage: DC 5V from adapter Polarization: Horizontal AC 120V, 60Hz Test Mode: Transmitting mode Remark: Absolute Level = Reading Level + Factor, Margin = Absolute Level – Limit Factor = Ant. Factor + Cable Loss – Pre-amplifier

Page 16 of 24 Report No.: HK1905201074-E Temperature: 22℃ Relative Humidity: 46% Test Date: May 27, 2019 Pressure: 1010hPa Test Voltage: DC 5V from adapter Polarization: Vertical AC 120V, 60Hz Test Mode: Transmitting mode Remark: Absolute Level = Reading Level + Factor, Margin = Absolute Level – Limit Factor = Ant. Factor + Cable Loss – Pre-amplifier

Page 17 of 24 Report No.: HK1905201074-E For Above 1GHz Test Results: PK AV Correction Emission Level Frequency Peak limit AV limit Margin Ant. Pol. Reading Reading Factor Peak AV (MHz) (dBμV/m) (dBμV/m) Peak(dB) (dBμV) (dBμV) (dB/m) (dBμV/m) (dBμV/m) 1824 H --- -4.34 47.11 --- 74.00 54.00 -22.55 2736 H --- -0.59 51.87 --- 74.00 54.00 -21.54 1830 V --- -4.22 52.11 --- 74.00 54.00 -17.67 2736 V --- -0.56 51.65 --- 74.00 54.00 -21.79 1825 H --- -4.18 47.38 --- 74.00 54.00 -22.44 2737.5 H --- -0.54 52.18 --- 74.00 54.00 -21.28 1825 V --- -4.34 53.44 --- 74.00 54.00 -16.22 2737.5 V --- -0.59 51.38 --- 74.00 54.00 -22.03 1826 H --- -4.22 47.29 --- 74.00 54.00 -22.49 2739 H --- -0.56 50.43 --- 74.00 54.00 -23.01 1826 V --- -4.18 52.11 --- 74.00 54.00 -17.71 2739 V --- -0.54 50.36 --- 74.00 54.00 -23.1 Note: 1. Emission Level = Peak Reading + Correction Factor; Correction Factor = Antenna Factor + Cable loss – Pre-amplifier 2. Margin = Emission - Limit 3. The emission levels of other frequencies are very lower than the limit and not show in test report. 4. Measurements were conducted from 1 GHz to the 10th harmonic of highest fundamental frequency. 5. Data of measurement shown “---“ in the above table mean that the reading of emissions is attenuated more than 20dB below the limits or the field strength is too small to be measured.

Page 18 of 24 Report No.: HK1905201074-E Band Edge Requirement: 912MHz PK AV Correction Emission Level Frequency Peak limit AV limit Margin Ant. Pol. Reading Reading Factor Peak AV (MHz) (dBμV/m) (dBμV/m) Peak(dB) (dBμV) (dBμV) (dB/m) (dBμV/m) (dBμV/m) 902 H 56.44 --- -3.9 52.54 --- 74 --- -21.46 928 H 56.46 --- -3.6 52.86 --- 74 --- -21.14 902 V 55.27 --- -3.7 51.57 --- 74 --- -22.43 928 V 52.56 --- -4.2 48.36 --- 74 --- -25.64 913MHz PK AV Correction Emission Level Frequency Peak limit AV limit Margin Ant. Pol. Reading Reading Factor Peak AV (MHz) (dBμV/m) (dBμV/m) Peak(dB) (dBμV) (dBμV) (dB/m) (dBμV/m) (dBμV/m) 902 H 56.09 --- -3.9 52.19 --- 74 --- -21.81 928 H 54.23 --- -3.6 50.63 --- 74 --- -23.37 902 V 52.87 --- -3.7 49.17 --- 74 --- -24.83 928 V 53.34 --- -4.2 49.14 --- 74 --- -24.86 Note: 1. Emission Level = Peak Reading + Correction Factor; Correction Factor = Antenna Factor + Cable loss – Pre-amplifier 2. Margin = Emission - Limit 3. The emission levels of other frequencies are very lower than the limit and not show in test report. 4. Measurements were conducted from 1 GHz to the 10th harmonic of highest fundamental frequency. 5. Data of measurement shown “---“ in the above table mean that the reading of emissions is attenuated more than 20dB below the limits or the field strength is too small to be measured.

Page 19 of 24 Report No.: HK1905201074-E 5 OCCUPIED BANDWIDTH TEST 5.1 Test Setup 5.2 Rules and specifications CFR 47 Part 15.215(c) ANSI C63.10: 2013 5.3 Test Procedure 1. According to the follow Test-setup, keep the relative position between the artificial antenna and the EUT. 2. Set to the maximum power setting and enable the EUT transmit continuously. 3. Use the following spectrum analyzer settings for 20dB Bandwidth measurement. Span = approximately 2 to 3 times the 20 dB bandwidth, centered on a hopping channel; RBW≥1% of the 20dB bandwidth; VBW≥RBW; Sweep = auto; Detector function = peak; Trace = max hold. 4. Measure and record the results in the test report.

Page 20 of 24 Report No.: HK1905201074-E 5.4 Test Result PASS 20dB Bandwidth Mode Frequency(MHz) Limit (kHz) Conclusion (KHz) TX 912 276.1 / PASS TX 912.5 268.9 / PASS TX 913 268.7 / PASS 912Mhz 912.5Mhz

Page 21 of 24 Report No.: HK1905201074-E 913Mhz

Page 22 of 24 Report No.: HK1905201074-E 6 ANTENNA REQUIREMENT Standard Applicable: For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. Antenna Connected Construction The antenna used in this product is a PCB Internal, The directional gains of antenna used for transmitting is 0dBi. ANTENNA

Page 23 of 24 Report No.: HK1905201074-E 7 PHOTOGRAPH OF TEST 7.1 Radiated Emission

Page 24 of 24 Report No.: HK1905201074-E 7.2 Conducted Emission ***End of Report***


Document Created: 2019-06-14 18:21:20
Document Modified: 2019-06-14 18:21:20
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC