2AS2S-DM563U0_User-Manual

FCC ID: 2AS2S-DM563U0

Users Manual

Download: PDF
FCCID_4257620

DM563U0 User Reference Guide Document Ref. Number: RKH-02900009 Version: V1.0.1

DMS63U0 Build Revision Version Modified Modifier Approver Date Department Hardware V1.0.0 Initial Version XIXXT Robo 2018—12—27 Development Improve power source & Hardware V1.0.1 operating temperature xIXT Robo 2019—03—15 Development threshold I| P a ge COrE WAV

DM563U0 Table of Contents Build Revision ..................................................................................................................................... I 1. Product Introduction ................................................................................................................. 1 1.1 Overview ................................................................................................................................. 1 1.2 Product Specification .............................................................................................................. 1 1.3 Application Block Diagram ...................................................................................................... 2 2. RF Parameters ........................................................................................................................... 3 3. PCB design and packaging ............................................................................................................. 4 II | P a g e

1. Product Introduction 1.1Overview DM563U0O is a Wifi dedicated module based on QUALCOMM QCA9563+0CA9880 with 128MB DDR2 RAM & 16MB SPI Flash. It complies with IEEE802.11a/n/ac wireless network protocol. €0000—9€0 §14 BEncdus 1.2Product Specification Table 1 Product Specifications CPU Model QCA9563+0CA9880 RAM 128MB DDR2 Flash 16M SPI Input Voltage 3.3V DC Operating —25C~+55°C Temperature Operating mt 5%—95% (Non—Condensing) 1 | Pa ge COrE WAV

DM563U0 1.3Application Block Diagram 2|Page

DM563U0 2. RF Parameters DM563U0 supports all modulation modes and rates under 802.11a/n/ac. The transmission parameters are shown in Operation Description, and the receiver parameters are shown in below table. 1 Receiver Sensitivity Parameter Table Receiver Sensitivity Modulation Data Rates (dbm) 6Mbps -94 9Mbps -94 12Mbps -92 5GHz 18Mbps -91 802.11a 24Mbps -90 36Mbps -86 48Mbps -83 54Mbps -80 MCS0 -93 MCS1 -90 MCS2 -87 5GHz MCS3 -83 802.11n/ac MCS4 -80 VHT20 MCS5 -77 MCS6 -74 MCS7 -73 MCS8 -71 MCS0 -90 MCS1 -88 MCS2 -85 MCS3 -82 5GHz MCS4 -80 802.11n/ac MCS5 -75 VHT40 MCS6 -73 MCS7 -73 MCS8 -70 MCS9 -68 MCS0 -89 5GHz MCS1 -87 802.11ac MCS2 -85 VHT80 MCS3 -83 MCS4 -80 3|Page

DMS63U0 MCSS5 MCS6 MCS7 MCS8 MCS9 Note: 1) Tolerance of £2dbm 3. PCB design and packaging 4 | P a ge COrE WAV

DM563U0 Federal Communications Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  Reorient or relocate the receiving antenna.  Increase the separation between the equipment and receiver.  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.  Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. 5|Page

DM563U0 RF exposure warning This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This product may not be collocated or operated in conjunction with any other antenna or transmitter This equipment must be installed and operated in accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be collocated or operating in conjunction with any other antenna or transmitter. OEM Integration Instructions： This device is intended only for OEM integrators under the following conditions: The module can be used to installation in other host. The antenna must be installed such that 20 cm is maintained between the antenna and users, and the transmitter module may not be co-located with any other transmit or antenna. The module shall be only used with the integral antenna(s) that has been originally tested and certified with this module. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirement with this module installed (for example, digital device emission, PC peripheral requirements, etc.) IMPORTANT NOTE： In the event that these conditions cannot be met (for example certain laptop configuration or co-location with another transmitter), then the FCC authorization for this module in combination with the host equipment is no longer considered valid and the FCC ID of the module cannot be used on the final product. In these and 6|Page

DM563U0 circumstance, the OEM integrator will be responsible for re-evaluating. The end product (including the transmitter) and obtaining a separate FCC authorization. The final end product must be labeled in a visible area with the following: “Contains Transmitter Module FCC ID: 2AS2S-DM563U0 or Contains FCC ID: 2AS2S-DM563U0”. Antenna Specification: Antenna Frequency Tx Max Antenna CDD Directional Gain (dBi) Type Band (MHz) Paths Gain (dBi) For Power For PSD External 5150 ~ 5250 3 2.5 2.5 7.27 Antenna 5725 ~ 5850 Note: 1. 802.11a support single transmission only. 2. The EUT supports Cyclic Delay Diversity (CDD) technology and doesn’t support Beam-forming technology, and CDD signals are correlated. 7|Page


Document Created: 2019-04-30 07:50:52
Document Modified: 2019-04-30 07:50:52
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC