Test Report

FCC ID: 2ARWA-BS1301

Test Report

Download: PDF

FCCID_4276402

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ARWA-BS1301 Report No.: LCS181115066AEA

FCC TEST REPORT
FOR
Dongguan King Yuk Supply Chain Company Limited
Wireless Charging with Bluetooth Speaker
Test Model: BS1301
Additional Model No.: DocknRoll

Prepared for : Dongguan King Yuk Supply Chain Company Limited
Floor 4th, Ao Bei Road No.9, Yantian Village, Fenggang Town,
Address :
Dongguan, Guangdong, China

Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd.
1/F., Xingyuan Industrial Park, Tongda Road, Bao’an Avenue,
Address :
Bao’an District, Shenzhen, Guangdong, China
Tel : (+86)755-82591330
Fax : (+86)755-82591332
Web : www.LCS-cert.com
Mail : webmaster@LCS-cert.com

Date of receipt of test sample : November 21, 2018
Number of tested samples : 1
Serial number : Prototype
Date of Test : November 21, 2018 ~ April 29, 2019
Date of Report : April 29, 2019

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 1 of 19

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ARWA-BS1301 Report No.: LCS181115066AEA

FCC -- TEST REPORT

April 29, 2019
Test Report No. : LCS181115066AEA Date of issue

Test Model........................ : BS1301

EUT.................................... : Wireless Charging with Bluetooth Speaker

Applicant........................... : Dongguan King Yuk Supply Chain Company Limited
Floor 4th, Ao Bei Road No.9, Yantian Village, Fenggang Town,
Address.............................. :
Dongguan, Guangdong, China
Telephone.......................... : /
Fax..................................... : /

Manufacturer..................... : Dongguan King Yuk Supply Chain Company Limited
Floor 4th, Ao Bei Road No.9, Yantian Village, Fenggang Town,
Address.............................. :
Dongguan, Guangdong, China
Telephone.......................... : /
Fax..................................... : /

Factory.............................. : Dongguan King Yuk Supply Chain Company Limited
Floor 4th, Ao Bei Road No.9, Yantian Village, Fenggang Town,
Address.............................. :
Dongguan, Guangdong, China
Telephone.......................... : /
Fax..................................... : /

Test Result Positive

The test report merely corresponds to the test sample.
It is not permitted to copy extracts of these test result without the written permission of the test laboratory.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 3 of 19

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ARWA-BS1301 Report No.: LCS181115066AEA

Revision History
Revision Issue Date Revisions Revised By
000 April 29, 2019 Initial Issue Gavin Liang

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 4 of 19

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ARWA-BS1301 Report No.: LCS181115066AEA

TABLE OF CONTENTS

1. GENERAL INFORMATION................................................................................................................. 6
1.1 Description of Device (EUT) ........................................................................................................................6
1.2 Support equipment List ................................................................................................................................6
1.3 External I/O Cable ........................................................................................................................................6
1.4 Description of Test Facility ..........................................................................................................................6
1.5 Statement of the Measurement Uncertainty .............................................................................................7
1.6 Measurement Uncertainty ...........................................................................................................................7
1.7 Description of Test Modes ...........................................................................................................................7
2. TEST METHODOLOGY ...................................................................................................................... 8
2.1 EUT Configuration ........................................................................................................................................8
2.2 EUT Exercise .................................................................................................................................................8
2.3 General Test Procedures.............................................................................................................................8
2.3.1 Conducted Emissions ...............................................................................................................................8
2.3.2 Radiated Emissions ..................................................................................................................................8
3. SYSTEM TEST CONFIGURATION ................................................................................................... 9
3.1 Justification ....................................................................................................................................................9
3.2 EUT Exercise Software ................................................................................................................................9
3.3 Special Accessories .....................................................................................................................................9
3.4 Block Diagram/Schematics .........................................................................................................................9
3.5 Equipment Modifications ..............................................................................................................................9
3.6 Test Setup ......................................................................................................................................................9
4. SUMMARY OF TEST EQUIPMENT ................................................................................................ 10
5. SUMMARY OF TEST RESULT........................................................................................................ 11
6. POWER LINE CONDUCTED MEASUREMENT ........................................................................... 12
7. RADIATED EMISSION MEASUREMENT ...................................................................................... 14
8. PHOTOGRAPHS OF TEST SETUP................................................................................................ 19
9. EXTERNAL PHOTOGRAPHS OF THE EUT................................................................................. 19
10. INTERNAL PHOTOGRAPHS OF THE EUT................................................................................ 19

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 5 of 19

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ARWA-BS1301 Report No.: LCS181115066AEA

1. GENERAL INFORMATION

1.1 Description of Device (EUT)

EUT : Wireless Charging with Bluetooth Speaker
Test Model : BS1301
Additional Model No. : DocknRoll
PCB board, structure and internal of these model(s) are the
Model Declaration :
same, Only the model name is different for these models.
Wireless Charger Input: DC 5V 2A or DC 9V 1.67A
Power Supply :
Output: 5V 1A or 9V 1.1A
Hardware Version : A6
Software Version : A2
WPT
Operating Frequency : 110 KHz – 205 KHz
Modulation Type : CW (Continuous Wave)
Antenna Type : Coil Antenna

1.2 Support equipment List

Manufacturer Description Model Serial Number Certificate
Apple Mobile Phone iPhone 8 Plus -- FCC ID
ShenZhen HuaJin
AC Adapter HJ-FC016K7-US -- FCC sDoC
Electronics CO.,LTD.
Dongguan King Yuk Wireless Charging
Supply Chain with Bluetooth BS1301 -- FCC ID
Company Limited Speaker

1.3 External I/O Cable

I/O Port Description Quantity Cable
USB Port 2 1m
AUX Port 1 1m

1.4 Description of Test Facility
FCC Registration Number. is 254912.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 6 of 19

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ARWA-BS1301 Report No.: LCS181115066AEA

Industry Canada Registration Number. is 9642A-1.
ESMD Registration Number. is ARCB0108.
UL Registration Number. is 100571-492.
TUV SUD Registration Number. is SCN1081.
TUV RH Registration Number. is UA 50296516-001
NVLAP Registration Code is 600167-0
The 3m-Semi anechoic test site fulfils CISPR 16-1-4 according to ANSI C63.4:2014 and CISPR
16-1-4:2010 SVSWR requirement for radiated emission above 1GHz.
1.5 Statement of the Measurement Uncertainty
The data and results referenced in this document are true and accurate. The reader is cautioned that
there may be errors within the calibration limits of the equipment and facilities. The measurement
uncertainty was calculated for all measurements listed in this test report acc. To CISPR 16 – 4
“Specification for radio disturbance and immunity measuring apparatus and methods – Part 4:
Uncertainty in EMC Measurements” and is documented in the LCS quality system acc. To DIN EN
ISO/IEC 17025. Furthermore, component and process variability of devices similar to that tested may
result in additional deviation. The manufacturer has the sole responsibility of continued compliance of
the device.

1.6 Measurement Uncertainty
Test Item Frequency Range Uncertainty Note
9KHz~30MHz 3.10dB (1)
30MHz~200MHz 2.96dB (1)
Radiation Uncertainty : 200MHz~1000MHz 3.10dB (1)
1GHz~26.5GHz 3.80dB (1)
26.5GHz~40GHz 3.90dB (1)
Conduction Uncertainty : 150kHz~30MHz 1.63dB (1)
Power disturbance : 30MHz~300MHz 1.60dB (1)

(1). This uncertainty represents an expanded uncertainty expressed at approximately the 95%
confidence level using a coverage factor of k=2.

1.7 Description of Test Modes
Equipment under test was operated during the measurement under the following conditions:
Charging mode
Modulation Type: CW (Continuous Wave)

Test Modes:
Mode 1 AC/DC Adapter + EUT + Bluetooth Speaker + Mobile Phone (Battery Status: <1%) Record
Mode 2 AC/DC Adapter + EUT + Bluetooth Speaker + Mobile Phone (Battery Status: <50%) Pre-tested
Mode 3 AC/DC Adapter + EUT + Bluetooth Speaker + Mobile Phone (Battery Status: 100%) Pre-tested
Mode 4 AC/DC Adapter + EUT + Mobile Phone (Battery Status: <1%) Pre-tested
Mode 5 AC/DC Adapter + EUT + Mobile Phone (Battery Status: <50%) Pre-tested
Mode 6 AC/DC Adapter + EUT + Mobile Phone (Battery Status: 100%) Pre-tested
Note: All test modes were pre-tested, but we only recorded the worst case in this report.
For AC conducted emission, pre-test at both AC 120V/60Hz and AC 240V/50Hz, recorded worst case;

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 7 of 19

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ARWA-BS1301 Report No.: LCS181115066AEA

2. TEST METHODOLOGY
The tests documented in this report were performed in accordance with MP-5, and FCC CFR PART 18.

2.1 EUT Configuration
The EUT configuration for testing is installed on RF field strength measurement to meet the
Commissions requirement and operating in a manner that intends to maximize its emission
characteristics in a continuous normal application.

2.2 EUT Exercise
The EUT was operated in the charging and compunction mode to fix the TX frequency that was for the
purpose of the measurements.
According to its specifications, the EUT must comply with the requirements of the Section 18.305 and
18.307 under the FCC Rules Part 18.

2.3 General Test Procedures

2.3.1 Conducted Emissions
The EUT is placed on the turntable, which is 0.8 m above ground plane. According to the requirements
in FCC MP-5 for Conducted emissions from the EUT measured in the frequency range between 0.15
MHz and 30MHz using Quasi-peak and average detector modes.

2.3.2 Radiated Emissions
The EUT is placed on a turn table, which is 0.8 m above ground plane. The turntable shall rotate 360
degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving
antenna, which varied from 1m to 4m to find out the highest emission. And also, each emission was to
be maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to
find out the maximum emissions, exploratory radiated emission measurements were made according to
the requirements in FCC MP-5 for radiated emission.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 8 of 19

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ARWA-BS1301 Report No.: LCS181115066AEA

3. SYSTEM TEST CONFIGURATION

3.1 Justification
The system was configured for testing in a normal condition.

3.2 EUT Exercise Software
N/A.

3.3 Special Accessories
N/A.

3.4 Block Diagram/Schematics
Please refer to the related document.

3.5 Equipment Modifications
Shenzhen LCS Compliance Testing Laboratory Ltd. has not done any modification on the EUT.

3.6 Test Setup
Please refer to the test setup photo.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 9 of 19

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ARWA-BS1301 Report No.: LCS181115066AEA

5. SUMMARY OF TEST RESULT

FCC Rule Temperature Power source
Test Item C NC NA NP Remark
No. conditions conditions
Radiated
§18.305 (b) Nominal Nominal -/-
Emission
AC conducted
§18.307 (a) Nominal Nominal -/-
emission

Remark: The measurement uncertainty is not included in the test result.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 11 of 19

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ARWA-BS1301 Report No.: LCS181115066AEA

7.3. EUT Configuration on Measurement
The following equipment are installed on Radiated Emission Measurement to meet the commission
requirements and operating regulations in a manner which tends to maximize its emission
characteristics in normal application.

7.4. Operating Condition of EUT
(1) Setup the EUT as shown in Section 4.1.
(2) Let the EUT work in worst test mode (Mode 1) and measure it.

7.5. Measuring Setting
The following table is the setting of spectrum analyzer and receiver.

Receiver Parameter Setting
Attenuation Auto
Start ~ Stop Frequency 9kHz~150kHz / RB 200Hz for QP/Average
Start ~ Stop Frequency 150kHz~30MHz / RB 9kHz for QP/Average
Start ~ Stop Frequency 30MHz~1000MHz / RB 100kHz for QP

7.6. Test Procedure

1) Sequence of testing 9 kHz to 30 MHz
Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or described
by manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 0.8 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions.
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.
Premeasurement:
--- The turntable rotates from 0°to 315°using 45°steps.
--- The antenna height is 0.8 meter.
--- At each turntable position the analyzer sweeps with peak detection to find the maximum of all
emissions
Final measurement:
--- Identified emissions during the premeasurement the software maximizes by rotating the turntable
position (0°to 360°) and by rotating the elevation axes (0°to 360°).
--- The final measurement will be done in the position (turntable and elevation) causing the highest
emissions with QPK detector.
--- The final levels, frequency, measuring time, bandwidth, turntable position, correction factor, margin
to the limit and limit will be recorded. Also a plot with the graph of the premeasurement and the limit will
be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 15 of 19

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ARWA-BS1301 Report No.: LCS181115066AEA

2) Sequence of testing 30 MHz to 1 GHz
Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or described
by manufacturer.
--- If the EUT is a tabletop system, a table with 0.8 m height is used, which is placed on the ground
plane.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.
Premeasurement:
--- The turntable rotates from 0°to 315°using 45°steps.
--- The antenna is polarized vertical and horizontal.
--- The antenna height changes from 1 to 3 meter.
--- At each turntable position, antenna polarization and height the analyzer sweeps three times in peak
to find the maximum of all emissions.
Final measurement:
--- The final measurement will be performed with minimum the six highest peaks.
--- According to the maximum antenna and turntable positions of premeasurement the software
maximize the peaks by changing turntable position (± 45°) and antenna movement between 1 and 4
meter.
--- The final measurement will be done with QP detector with an EMI receiver.
--- The final levels, frequency, measuring time, bandwidth, antenna height, antenna polarization,
turntable angle, correction factor, margin to the limit and limit will be recorded. Also a plot with the graph
of the premeasurement with marked maximum final measurements and the limit will be stored.

7.7. Test Results

PASS.

Only report the worst test data (Mode 1) in test report;

The test data please refer to following page:

Temperature 24.3℃ Humidity 57%
Test Engineer AKING JIN Configurations WPT

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 16 of 19

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2ARWA-BS1301 Report No.: LCS181115066AEA

8. PHOTOGRAPHS OF TEST SETUP

Please refer to separated files for Test Setup Photos of the EUT.

9. EXTERNAL PHOTOGRAPHS OF THE EUT

Please refer to separated files for External Photos of the EUT.

10. INTERNAL PHOTOGRAPHS OF THE EUT

Please refer to separated files for Internal Photos of the EUT.

-------------THE END OF REPORT-------------

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 19 of 19

Document Created: 2019-05-09 17:35:37
Document Modified: 2019-05-09 17:35:37

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC