User Manual

FCC ID: 2ARPWWSA5TR

Users Manual

Download: PDF
FCCID_4239245

transmitter, and plug other end into the (c) 5V 1A power supply, and plug into an120V Application 2: WSA—5TR with a Powered/Active Surround Speaker (Or the AC outlet Receiver — with Powered/Active Subwoofer, or Powered/Active Surround loudspeakers with their own amplifier) Speakers Receiver — with Powered/Active Subwoofer, or Powered/Active Surround Speakers Application 1: WSA—5TR Wireless Receiver with a Powered/Active Subwoofer Option A: connecting with 2 channels stereo amplifier + Passive Speaker — Connecting with 2 channels stereo amplifier + Passive Speaker — Use the supplied (d) stereo RCA cable to connect the (b) WSA—5TR wireless receiver L + R output to your 2 channels stereo amplifier audio RCA line In, the amplifier should be connected with passive speaker via conventional speaker wiring 0 0 @ USB 5V @flmlfl? RCA cable USB cable J power adapter @«<m»V | or Camins The WSA—5TR 5.8G wireless set transmits full frequency audio and can be used for full— LFE IN frequency active speakers) — O \ T Option B: connecting with Powered/Active Surround Speaker — Use the supplied (d) powek 4 Aubpio ouTPut stereo RCA cable to connect the (b) WSA—5TR wireless receiver L+R output to your pair RX of powered/active speaker‘s audio RCA line In. Place the subwoofer at its intended location (refer to your subwoofer owner‘s manual), and using the supplied (d) RCA cable to connect the (b) WSA—5TR wireless receiver LINE IN poms ‘ audio output to your subwoofer audio input. If you‘re using a different sub that only has a single LFE input, connect the same color L @CU:fl]]D:E—\ RCA cable RCA that you used for yourAV Receivers SUB / LFE out, and leave the other unplugged : @Cl»— on the WSA—5TR audio output and subwoofer audio input €


Set up the Transmitter and Receiver Pairing the Transmitter and Receiver Transmitter— with an AV Receiver/Surround Processor, or 2 Channels Pre—Amp have a **For the best audio signal quality results, please ensure that there are no obstacles to line level subwoofer output labeled Subwoofer Pre Out, Sub Out, SW Out..etc install within 50~100 feet operation distance between the transmitter and receiver/ Application 1: WSA—5TR with an 5.1/7.1 AV Receiver or Surround Processor speakers with line—of—sight (no walls or solid barriers) *The transmitter and receiver are automatically paired and synced as the factory with blue LED on solid when powered on 1@_. @_- T—__—I 3 L_—S R le L/Mono CA cab Aubto ouTPut 1 @ USB 5V *Successful pairing will be indicated by a steady blue light on the transmitter and receiver. USB cable power adapter *The transmitter and receiver have a pairing button on the back panel with 45 channel auto selection, if you experience any interference, or the flashing light indicates the units Step 1 — Use the supplied (d) RCA cable to connect the Subwoofer Pre—Out or LFE are not paired. Simply press and hold the M button on both units for 5 seconds, both will output of your AV receiver and to the (a) WSA—5TR wireless transmitter Audio Input. blink a few times then turn solid blue when they are successfully paired. You can leave right RCA plug unconnected if you are connecting to a subwoofer as FCC STATEMENT mono signal 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: Step 2 — Plug supplied (e) USB A to Micro B cable into "POWER" on the (a) WRA—5TR (1) This device may not cause harmful interference, and transmitter, and plug other end into the (c) 5V 1A power supply, and plug into an120V (2) This device must accept any interference received, including interference that may cause undesired AC outlet operation. Application 2: WSA—5TR Wireless Transmitter with a 2 Channel Stereo Pre—Amplifier: 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment. RECEIVER/PREAMP LINE LEVEL OUTPUTS NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, ::::: pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against "HB orn + harmful interference in a residential installation. “ ~O This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the USB 5V USB cable power adapter equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Step 1 — Use the supplied (d) RCA cable to connector the 2 channel stereo pre— Increase the separation between the equipment and receiver. amplifier‘s L/R line level Pre—Outs to (a) WSA—5TR wireless transmitter L/R input Connect the equipment into an outlet on a circuiit different from that to which the receiver is connected. *Leave right RCA plug unconnected ifyou have a mono source Consult the dealer or an experienced radio/TV technician for help. Step 2 — Plug supplied (e) USB A to Micro B cable into "POWER" on the (a) WRA—5TR


Document Created: 2018-10-26 10:48:56
Document Modified: 2018-10-26 10:48:56
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC