FCC_ID_Report

FCC ID: 2AROV-GPMB10

Test Report

Download: PDF
FCCID_4189829

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 FCC 47 CFR PART 15 SUBPART C TEST REPORT FOR GRENOPLUS IMATE ALL IN ONE DOCKING STATION (60W) Model : GP-MB10 Issued to GRENO TECHNOLOGY (HK) CO., LTD ROOM 603, 6/F,HANG PONT COMMERCIAL BUILDING, 31 TONKIN STREET,CHEUNG SHA WAN, KOWLOON HONGKONG Issued by WH Technology Corp. Open Site No.120, Ln. 5, Hudong St., Xizhi Dist., New Taipei City 221, Taiwan (R.O.C.) EMC Xizhi Office 7F., No.262, Sec. 3, Datong Rd., Xizhi Dist., New Test and Lab Taipei City 221, Taiwan (R.O.C.) Site Tel.: +886-7729-7707 Fax: +886-2- 8648-1311 Note: This test refers exclusively to the test presented test model and sample. This report shall not be reproduced except in full, without the written approval of WH Technology Corp.. This document may be altered or revised by WH Technology Corp.. Personnel only, and shall be noted in the revision section of the document. Page 1/21

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 1. GENERAL INFORMATION..................................................................................................................................3 2. REPORT OF MEASUREMENTS AND EXAMINATIONS............................................................................... 4 2.1 LIST OF MEASUREMENTS AND EXAMINATIONS....................................................................................................4 3. TEST CONFIGURATION OF EQUIPMENT UNDER TEST............................................................................5 3.1 DESCRIPTION OF THE TESTED SAMPLES............................................................................................ 5 3.3 TEST MODE AND TEST SOFTWARE......................................................................................................... 5 3.4 TEST METHODOLOGY & GENERAL TEST PROCEDURES..................................................................6 4. TEST AND MEASUREMENT EQUIPMENT....................................................................................................... 8 4.1 CALIBRATION................................................................................................................................................... 8 4.2 EQUIPMENT...................................................................................................................................................... 8 5. ANTENNA REQUIREMENTS............................................................................................................................. 10 5.1 STANDARD APPLICABLE............................................................................................................................ 10 5.2 ANTENNA CONSTRUCTION AND DIRECTIONAL GAIN....................................................................... 10 6. TEST OF CONDUCTED EMISSION..................................................................................................................11 6.1 TEST LIMIT...................................................................................................................................................... 11 6.2 TEST PROCEDURES.................................................................................................................................... 11 6.3 TYPICAL TEST SETUP................................................................................................................................. 12 6.4 TEST RESULT AND DATA........................................................................................................................... 13 7. TEST OF RADIATED EMISSION...................................................................................................................... 15 7.1 TEST LIMIT......................................................................................................................................................... 15 7.2 TEST PROCEDURES............................................................................................................................................. 15 7.3 TYPICAL TEST SETUP......................................................................................................................................... 16 7.4 TEST RESULT AND DATA (9KHZ ~ 30MHZ)...................................................................................................... 17 7.5 TEST RESULT AND DATA (30MHZ ~ 1GHZ, WORST EMISSIONS FOUND)...........................................................19 8. RESTRICTED BANDS OF OPERATION.......................................................................................................... 21 8.1 LABELING REQUIREMENT...................................................................................................................................21 Page 2/21

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 1. GENERAL INFORMATION Applicant : GRENO TECHNOLOGY (HK) CO., LTD Address : ROOM 603, 6/F,HANG PONT COMMERCIAL BUILDING, 31 TONKIN STREET,CHEUNG SHA WAN, KOWLOON HONGKONG Manufacturer : GRENO TECHNOLOGY (HK) CO., LTD Address : ROOM 603, 6/F,HANG PONT COMMERCIAL BUILDING, 31 TONKIN STREET,CHEUNG SHA WAN, KOWLOON HONGKONG Factory : Stiger International Trade Investment Co.,Ltd Address : 2 Building, Standard Garden, Taishi Industrial Zone, Dongyong Town, Nansha District Guangzhou, Guangdong, P.R.China EUT : Grenoplus iMate All in One Docking Station (60w) Model Name : GP-MB10 FCC ID : 2AROV-GPMB10 Trade Name : iMate Model : N/A Differences Is here with confirmed to comply with the requirements set out in the FCC Rules and Regulations Part 15 Subpart C and the measurement procedures were according to ANSI C63.10-2013. The said equipment in the configuration described in this report shows the maximum emission levels emanating FCC part 15 Subpart C Receipt Date : 11/01/2018 Final Test Date :12/30/2018 Tested By: Reviewed by: Nov. 01, 2018 Dec. 30, 2018 (Date) Bing Chang/ Engineer (Date) Bell Wei / Manager Designation Number: TW2954 Page 3/21

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 2. REPORT OF MEASUREMENTS AND EXAMINATIONS 2.1 LIST OF MEASUREMENTS AND EXAMINATIONS FCC Rule Item Result 15.207 Conducted Emission PASS 15.205 Radiated Emission PASS 15.209 15.203 Antenna Requirement PASS Page 4/21

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 3. TEST CONFIGURATION OF EQUIPMENT UNDER TEST 3.1 DESCRIPTION OF THE TESTED SAMPLES Test Model : GP-MB10 Input : AC 100-240V 1.8A (Max) Output C1 : DC 20V/2A,15V/2A,9V/2A & 5.2V/2A(Max)(PD) Output C2 : DC 9V/1A & 5.2V/2.4A(Max)(PD) USB 2.0 & 3.0 : 5.2V/2.4A (Max) Wireless Dongles : 500mA Output C1 & 2 : ThunderBolt 10Gb/s USB 2.0 : 480Mbps USB 3.0 : 5Gb/s High Definition MI : 4K 30Hz SD Card : 104Mbp/s Operate : 110KHz-200KHz Frequency Antenna Type : Coil Antenna Antenna gain : 0dBi 3.2 TEST MODE AND TEST SOFTWARE a. During testing, the interface cables and equipment positions were varied according to ANSI C63.10-2013. b. The complete test system included Notebook and EUT for RF test. c. only the worst case was recorded in this report Page 5/21

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 3.3 TEST METHODOLOGY & GENERAL TEST PROCEDURES All testing as described bellowed were performed in accordance with ANSI C63.10:2013 and FCC CFR 47 Part 15 Subpart C . Conducted Emissions The EUT is placed on a wood table, which is at 0.8 m above ground plane acceding to clause 15.207 and requirements of ANSI C63.10:2013. Conducted emissions from the EUT measured in the frequency range between 0.15 MHz and 30MHz are using CISPR Quasi-Peak / Average detectors. Radiated Emissions The EUT is a placed on a turn table, which is 0.8 m above ground plane. The turntable was rotated through 360 degrees to determine the position of maximum emission level. The EUT is placed at 3m away from the receiving antenna, which varied from 1m to 4m to find out the highest emission. Each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 1)Putting the EUT on the platform and turning on the EUT (on/off button on the bottom of the EUT). 2)Setting test channel described as “Channel setting and operating condition”, and testing channel by channel. 3)For the maximum output power measurement, we followed the method of measurement ANSI C63.10. 4)For the spurious emission test based on ANSI C63.10, at the frequency where below 1GHz used quasi-peak detector mode; where above 1GHz used the peak and average detector mode. IF the peak value may be under average limit, the average mode will not be performed. 3.4 MEASUREMENT UNCERTAINTY Measurement Item Uncertainty Radiated emission ±4.11dB Peak Output Power(conducted) ±1.38dB Peak Output Power(Radiated) ±1.70dB Power Spectral Density ±1.39dB Radiated emission(3m) ±4.11dB Radiated emission(10m) ±3.89dB Page 6/21

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 3.5 DESCRIPTION OF THE SUPPORT EQUIPMENTS Setup Diagram See test photographs attached in appendix 1 for the actual connections between EUT and support equipment. Support Equipment Peripherals Devices: Description Manufacturer Model No. Serial No. Laptop DELL Latutude 3379 F3M13F2 iWatch Apple Watch 3 FH7W260JJ5X4 Phone HUAWEI Mate10 BLA-AL00 TV SONY KDL-32W600D 2047973 Adapter SONY ACDP-04S03 149345210157413 SD Card Kingston U1 C10 N/A USB flash disk Kingston DTSE9EG2 N/A USB flash disk Kingston DTSE9EG2 N/A Type C Line : Unshielded ,Detachable, 0.2m Type C Line : Unshielded ,Detachable, 1.5m HDMI Line : Shielded ,Detachable, 1.8m Note: All the above equipment /cable were placed in worse case position to maximize emission signals during emission test Grounding: Grounding was in accordance with the manufacturer’s requirement and conditions for the intended use. Page 7/21

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 4. TEST AND MEASUREMENT EQUIPMENT 4.1 CALIBRATION The measuring equipment utilized to perform the tests documented in the report has been calibrated once a year or in accordance with the manufacturer ’ s recommendations, and is traceable to recognized national standards. 4.2 EQUIPMENT The following list contains measurement equipment used for testing. The equipment conforms to the requirement of CISPR 16-1, ANSI C63.2 and. Other required standards. Calibration of all test and measurement, including any accessories that may effect such calibration, is checked frequently to ensure the accuracy. Adjustments are made and correction factors are applied in accordance with the instructions contained in the respective. Page 8/21

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 TABLELIST OF TEST AND MEASUREMENT EQUIPMENT Next Cal. Instrument Manufacturer Model No. S/N Date EMI Receiver R&S ESHS10 830223/008 2019/06/05 Rolf Heine LISN NNB-2/16z 98062 2019/06/10 Hochfrequenztechnik 8-Wire ISN CAT5-8158- ISN Schwarzbeck 2019/09/20 CAT5 0094 RF Cable N/A N/A EMI-3 2019/10/18 MCTD2786 BLB16M040 Bilog antenna(30M-1G) ETC 2019/05/17 B 04/JB-5-004 Double Ridged Guide Horn DRH15N020 ETC MCTD 1209 2019/11/10 antenna(1G-18G) 09 Horn antenna (18G-26G) com-power AH-826 81000 2019/08/15 LOOP Antenna (Below 30M) com-power AL-130 17117 2019/10/03 Pre amplifier (30M-1G) EMC INSTRUMENT EMC9135 980334 2019/05/02 EMC05184 980108&AT Microwave Preamplifier (1G-18G) EMC INSTRUMENT 2019/10/22 5 -18001 JS4-180026 Pre amplifier (18G~26G) MITEQ 808329 2019/08/08 00-30-5A ESVS30 EMI Test Receiver R&S (20M-1000 826006/002 2019/11/10 MHz) N male on end of both RF Cable (open site) EMCI 30m 2019/10/18 sides (EMI4) HARBOUT LL142MI(4 RF CABLE (1~26G) NA 2019/04/16 INDUSTRIES M+4M) HARBOUT LL142MI(7 RF CABLE (1~26G) NA 2019/08/08 INDUSTRIES M) Spectrum (9K--7GHz) R&S FSP7 830180/006 2019/04/13 Spectrum (9K--40GHz) AGILENT 8564EC 4046A0032 2019/03/01 e3 AUDIX N/A N/A N/A SINGAL GENTERATOR 3619U0042 HP 8648A N/A (100k-1GHz) 6 Power Meter ANRITSU ML2487 6K00001574 2019/08/08 *CALIBRATION INTERVAL OF INSTRUMENTS LISTED ABOVE IS ONE YEAR Page 9/21

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 5. ANTENNA REQUIREMENTS 5.1 STANDARD APPLICABLE According to the FCC Part 15 Paragraph 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. 5.2 ANTENNA CONSTRUCTION AND DIRECTIONAL GAIN WPC Antenna Type : Coil Antenna Antenna Gain : 0 dBi Page 10/21

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 6. TEST OF CONDUCTED EMISSION 6.1 TEST LIMIT Conducted Emissions were measured from 150 kHz to 30 MHz with a bandwidth of 9 KHz on the 120 VAC power and return leads of the EUT according to the methods defined in ANSI C63.10-2013 The EUT was placed on a nonmetallic stand in a shielded room 0.8 meters above the ground plane as shown in section 2.2. The interface cables and equipment positioning were varied within limits of reasonable applications to determine the position produced maximum conducted emissions. The setup of EUT is according with per ANSI C63.10-2013 measurement procedure.The specification used was with the FCC Part 15.207 limits *Decreases with the logarithm of the frequency. 6.2 TEST PROCEDURES a. The EUT was placed 0.4 meter from the conducting wall of the shielding room was kept at least 80 centimeters from any other grounded conducting surface. b. Connect EUT to the power mains through a line impedance stabilization network (LISN). c. All the support units are connecting to the other LISN. d. The LISN provides 50 ohm coupling impedance for the measuring instrument. e. The FCC states that a 50 ohm, 50 micro-Henry LISN should be used. f. Both sides of AC line were checked for maximum conducted interference. g. The frequency range from 150 kHz to 30 MHz was searched. h. Set the test-receiver system to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. Page 11/21

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 6.3 TYPICAL TEST SETUP Page 12/21

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 6.4 TEST RESULT AND DATA M/N : GP-MB10 Test Voltage: AC 120V/60Hz Test Date : Nov. 06, 2018 Phase: L1 Temperature: 20℃ Relative Humidity: 54% Pressure: 101.0KPa Test by: Bing PD Charging to Laptop+Charging to Phone+HDMI Playing to TV+USB 3.0 data Test Mode: transmission+USB 2.0 data transmission+SD Card data transmission +Wireless Charging to iWatch Page 13/21

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 M/N : GP-MB10 Test Voltage: AC 120V/60Hz Test Date : May 29, 2018 Phase: Neutral Temperature: 20℃ Relative Humidity: 54% Pressure: 101.0KPa Test by: Bing PD Charging to Laptop+Charging to Phone+HDMI Playing to TV+USB 3.0 data Test Mode: transmission+USB 2.0 data transmission+SD Card data transmission +Wireless Charging to iWatch Page 14/21

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 7. TEST OF RADIATED EMISSION 7.1 TEST LIMIT In any 100kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20dB below that in the 100kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement. If the transmitter measurement is based on the maximum conducted output power, the attenuation required under this paragraph shall be 30dB instead of 20dB. In addition, radiated emissions which fall in section 15.205(a) the restricted bands must also comply with the radiated emission limit specified in section 15.209(a). 7.2 TEST PROCEDURES a. The EUT was placed on a rotatable table top 0.8 meter above ground. b. The EUT was set 3 meters from the interference receiving antenna which was mounted on the top of a variable height antenna tower. c. The table was rotated 360 degrees to determine the position of the highest radiation. d. The antenna is a broadband antenna and its height is varied between one meter and four meters above ground to find the maximum value of the field strength both horizontal polarization and vertical polarization of the antenna are set to make the measurement. e. For each suspected emission the EUT was arranged to its worst case and then tune the antenna tower (from 1 M to 4 M) and turn table (from 0 degree to 360 degrees) to find the maximum reading. f. Set the test-receiver system to Peak or CISPR quasi-peak Detect Function and specified bandwidth with Maximum Hold Mode. g. If the emission level of the EUT in peak mode was 3 dB lower than the limit specified, then testing will be stopped and peak values of EUT will be reported, Page 15/21

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 otherwise, the emissions which do not have 3 dB margin will be repeated one by one using the quasi-peak method and reported. h. For testing above 1GHz, the emission level of the EUT in peak mode was 20dB lower thanaverage limit (that means the emission level in peak mode also complies with the limit in average mode), then testing will be stopped and peak values of EUT will be reported, otherwise, the emissions will be measured in average mode again and reported. i. “ Cone of radiation ” has been considered to be 3dB bandwidth of the measurement antenna. 7.3 TYPICAL TEST SETUP Radiated Emission Test Set-Up, Frequency Below 30MHz Radiated Emission Test Set-Up, Frequency 30MHz-1000MHz Page 16/21

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 7.4 TEST RESULT AND DATA (9KHZ ~ 30MHZ) M/N : GP-MB10 Test Voltage: AC 120V/60Hz Test Date : Nov. 08, 2018 Phase: Vertical Temperature: 20℃ Relative Humidity: 54% Pressure: 101.0KPa Test by: Bing PD Charging to Laptop+Charging to Phone+HDMI Playing to TV+USB 3.0 data Test Mode: transmission+USB 2.0 data transmission+SD Card data transmission +Wireless Charging to iWatch Page 17/21

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 M/N : GP-MB10 Test Voltage: AC 120V/60Hz Test Date : Nov. 08, 2018 Phase: Vertical Temperature: 20℃ Relative Humidity: 54% Pressure: 101.0KPa Test by: Bing PD Charging to Laptop+Charging to Phone+HDMI Playing to TV+USB 3.0 data Test Mode: transmission+USB 2.0 data transmission+SD Card data transmission +Wireless Charging to iWatch Page 18/21

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 7.5 TEST RESULT AND DATA (30MHZ ~ 1GHZ, WORST EMISSIONS FOUND) M/N : GP-MB10 Test Voltage: AC 120V/60Hz Test Date : Nov. 08, 2018 Phase: Vertical Temperature: 20℃ Relative Humidity: 54% Pressure: 101.0KPa Test by: Bing PD Charging to Laptop+Charging to Phone+HDMI Playing to TV+USB 3.0 data Test Mode: transmission+USB 2.0 data transmission+SD Card data transmission +Wireless Charging to iWatch Page 19/21

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 M/N : GP-MB10 Test Voltage: AC 120V/60Hz Test Date : Nov. 08, 2018 Phase: Horizontal Temperature: 20℃ Relative Humidity: 54% Pressure: 101.0KPa Test by: Bing PD Charging to Laptop+Charging to Phone+HDMI Playing to TV+USB 3.0 data Test Mode: transmission+USB 2.0 data transmission+SD Card data transmission +Wireless Charging to iWatch Page 20/21

Date of Issue: January 23, 2019 WH Technology Corp. Report No. : WH-FCC-R18112104 FCC ID. : 2AROV-GPMB10 8. RESTRICTED BANDS OF OPERATION Only spurious emissions are permitted in any of the frequency bands listed below: **: Until February 1, 1999, this restricted band shall be 0.490-0.510 MHz 8.1 LABELING REQUIREMENT The device shall bear the following statement in a conspicuous location on the device: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. --END--- Page 21/21


Document Created: 2019-01-23 13:08:33
Document Modified: 2019-01-23 13:08:33
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC