Test Report

FCC ID: 2ARI2CK-KF-102

Test Report

Download: PDF
FCCID_4251342

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) FCC Part 15 Subpart B&C§15.247 Test Report Equipment Under Test CryptoKona S PLUS Model Name CryptoKona-KF102 Variant Model Name - Applicant KONA I Co., Ltd. Manufacturer KONA I Co., Ltd. Date of Test(s) 2019. 04. 01 ~ 2019. 04. 12 Date of Issue 2019. 04. 18 In the configuration tested, the EUT complied with the standards specified above. Issue to Issue by KONA I Co., Ltd. MOVON CORPORATION 4F, 3, Eunhaeng-ro, 498-2,Geumeo-ro, Pogok-eup, Yeongdeungpo-gu, Seoul, Republic Cheoin-gu, Yongin-si, of Korea Gyeonggi-do, Korea, 17030 Tel.:+81-2-2168-7650 Tel.: +82-31-338-8837 Fax:+81-2-2168-7650 Fax: +82-31-338-8847 Page : (1) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) Revision history Revision Date of issue Description Revised by 1 Apr 15, 2019 Initial - Changed FCC ID, Modified pages 17/33 and 2 Apr 18, 2019 18/33, Added to At the “Line(L1): Hot” / - “Line(N): Neutral” Page : (2) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) Table of contents 1. APPLICANT INFORMATION .......................................................................................... 4 2. LABORATORY INFORMATION ..................................................................................... 4 3. SUMMARY OF TEST RESULTS .................................................................................... 5 4. EUT DESCRIPTION ........................................................................................................ 6 5. MEASUREMENT EQUIPMENT ...................................................................................... 7 6. TRANSMITTER RADIATED SPURIOUS EMISSIONS AND CONDUCTED SPURIOUS EMISSIONS .................................................................................................................. 8 7. 6DB BANDWIDTH ........................................................................................................ 19 8. MAXIMUM PEAK CONDUCTED OUTPUT POWER .................................................... 22 9. PEAK POWER SPECTRAL DENSITY ......................................................................... 25 10. AC CONDUCTED POWER LINE TEST ..................................................................... 28 11. ANTENNA REQUIREMENT ....................................................................................... 31 12. RF EXPOSURE EVALUATION .................................................................................. 32 Page : (3) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 1. Applicant Information 1.1. Details of applicant Applicant : KONA I Co., Ltd. Address : 4F, 3, Eunhaeng-ro, Yeongdeungpo-gu, Seoul, Republic of Korea Contact Person : Mac Jeong Telephone : +81-2-2168-7650 Fax : +81-2-2168-7650 1.2. Manufacturer Information Manufacturer : KONA I Co., Ltd. Address : 4F, 3, Eunhaeng-ro, Yeongdeungpo-gu, Seoul, Republic of Korea 2. Laboratory Information Company name : MOVON CORPORATION Test site number : FCC (KR0151) Address : 498-2, Geumeo-ro, Pogok-eup, Cheoin-gu, Yongin-si, Gyeonggi-do, South Korea Page : (4) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

()VON MOVON CORPORA ORATION woven correramo« Report Number: MOV—19—RF—1029(1) 3. Summary of test results The EUT has been tested according to the following specifications: Section in ce FCC part 15 Description Result g}gggg Transmitter radiated spurious emissions, c §15 247(d) Conducted spurious emission §15.247(a)(2) 6 dB Bandwidth C §15.247(b)(e) Maximum peak conducted output power C §15.247(e) Peak Power Spectral Density C §15.207(a) AC Conducted power line test C X Abbreviation C Complied N/A Not applicable F Fail The sample was tested according to the following specification: FCC Parts 15.247; ANSI C63.4:2014, ANSI C63.10:2013 FCC Public Notice KDB 558074 DO1v05 Approval Signatories Test and Report Completed by : Report Approval by : ) ' David park Issac, Jin Test Engineer Technical Manager MOVON CORPORATION MOVON CORPORATION Page : (5) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 4. EUT Description Kind of product CryptoKona S PLUS Model Name CryptoKona-KF102 Variant Model Name - FCC ID 2ARI2CK-KF-102 IC Number - Power supply DC 3.0 V Frequency range 2 402 MHz ~ 2 480 MHz (Bluetooth LE) Modulation technique GFSK Number of channels 40 ch. (Bluetooth LE) Antenna gain 0.8 ㏈ i (Max.) Test Site Registration Number FCC (KR0151) 4.1. Table for Test Modes and Frequency Preliminary tests were performed in different data rate to find the worst radiated emission. The data rate shown in the table below is the worst-case rate with respect to the specific test item. Investigation has been done on all the possible configurations for searching the worst cases. The following table is a list of the test modes shown in this test report. Mode Data rate (Worst case) Frequency (Freq. MHz) Bluetooth LE 1 Mbps Lowest (2 402) / Middle (2 440) / Highest (2 480) Page : (6) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 5. Measurement equipment Calibration Calibration Calibration Equipment Manufacturer Model Serial number Interval date due. Test Receiver R&S ESVS30 829673/015 1 year 2018-12-06 2019-12-06 Signal Generator R&S SMB100A 178128 1 year 2018-12-07 2019-12-07 Spectrum R&S FSV-40 100832 1 year 2018-05-28 2019-05-28 Analyzer Power Meter Agilent E4416A GB41290645 1 year 2018-05-29 2019-05-29 Power Sensor Agilent 9327A US40441490 1 year 2018-05-29 2019-05-29 Horn Antenna R&S HF906 100236 2 year 2019-04-09 2021-04-09 Horn Antenna AH Systems SAS-572 269 2 year 2017-08-01 2020-08-01 Horn Antenna AH Systems SAS-573 164 2 year 2018-04-26 2020-04-26 Bi-Log Ant. S/B VULB 9161SE 4159 2 year 2018-06-11 2020-06-11 Loop Antenna ETS LINDGREN 6502 00118166 2 year 2018-10-30 2020-10-30 Power Amplifier TESTEK TK-PA18H 170013-L 1 year 2018-05-28 2019-05-28 Power Amplifier MITEQ AFS43-01002600 2048519 1 year 2018-10-29 2019-10-29 AMF-6F-2600400 Power Amplifier MITEQ 1511665 1 year 2018-12-10 2019-12-10 0-33-8P-HS SONOMA Power Amplifier 310N 185428 1 year 2018-12-07 2019-12-07 INSTRUMENT CO2000/064/6961003/ Controller INNCO CO2000 N/A N/A N/A L MA4000/038/6961003/ Antenna Master INNCO MA4000 N/A N/A N/A L CO3000/812/34240914 Controller INNCO CO3000 N/A N/A N/A /L Antenna Master INNCO MA4640-XP-ET None N/A N/A N/A TWO LINE-V- R&S ESH3-Z5 100296 1 year 2018-12-06 2019-12-06 NETWORK EMI TEST 1 year R&S ESR3 101873 2018-05-28 2019-05-28 RECEVER PULSE LIMITER R&S ESH3-Z2 100288 1 year 2018-05-28 2019-05-28 Power Divider HP 11636B 12481 1 year 2018-05-31 2019-05-31 RF Cable SUHNER SUCOFLEX100 84047746 N/A N/A N/A RF Cable SUHNER SUCOFLEX102 801270/2 N/A N/A N/A RF Cable SUHNER SUCOFLEX102 801270/2 N/A N/A N/A ※Remark Support equipment Description Manufacturer Model Serial number Notebook computer DELL Lattitude D510 - Page : (7) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 6. Transmitter radiated spurious emissions and conducted spurious emissions 6.1. Test setup 6.1.1. Transmitter radiated spurious emissions The diagram below shows the test setup that is utilized to make the measurements for emission from 9kHz to 30MHz Emissions. The diagram below shows the test setup that is utilized to make the measurements for emission from 30 ㎒ to 1 ㎓ emissions. Page : (8) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) The diagram below shows the test setup that is utilized to make the measurements for emission from 1 ㎓ to 40 ㎓ emissions. Page : (9) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 6.2. Limit According to §15.247(d), in any 100 ㎑ bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 ㏈ below that in the 100 ㎑ bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement , provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval , as permitted under paragraph(b)(3) of this section , the attenuation required under this paragraph shall be 30 ㏈ instead of 20 ㏈. Attenuation below the general limits specified in section §15.209(a) is not required. In addition, radiated emission which in the restricted band, as define in section §15.205(a), must also comply the radiated emission limits specified in section §15.209(a) (see section §15.205(c)) According to § 15.109(a), for an intentional radiator devices, the general required of field strength of radiated emissions from unintentional radiators at a distance of 3 meters shall not exceed the following values： Frequency Distance Radiated at 3M Radiated (㎒) (Meters) (㏈㎶/m) (㎶/m) 0.009–0.490 300 2400/F(㎑) 0.490–1.705 30 See the remark 24000/F(㎑) 1.705–30.0 30 30 30 - 88 3 40.0 100 88 – 216 3 43.52 150 216 – 960 3 46.02 200 Above 960 3 53.97 500 ※Remark 1. Emission level in ㏈ uV/m=20 log (uV/m) 2. Measurement was performed at an antenna to the closed point of EUT distance of meters. 3. Distance extrapolation factor =40log(Specific distance/ test distance)(㏈) Limit line=Specific limits(㏈ uV) + distance extrapolation factor. Page : (10) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 6.3. Test procedures Radiated emissions from the EUT were measured according to the dictates of ANSI C63.10:2013 In case of the air temperature of the test site is out of the range is 10 to 40°C before the testing proceeds the warm-up time of EUT maintain adequately 6.3.1. Test procedures for radiated spurious emissions 1. The EUT is placed on a turntable, which is 0.8 m (Below 1 ㎓.)/ 1.5 m (Above 1 ㎓) above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3 m away from the receiving antenna, which is varied from 1m to 4m to find out the highest emissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna both horizontal and vertical. 6. Repeat above procedures until the measurements for all frequencies are complete. ※Remark 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 10 ㎑ for Peak detection (PK) at frequency below 30 ㎒ 2. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120 ㎑ for Peak detection (PK) or Quasi-peak detection (QP) at frequency below 1 ㎓. 3. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 1 ㎒ for Peak detection and frequency above 1 ㎓. 4. The resolution bandwidth of test receiver/spectrum analyzer is 1 ㎒ z and the video bandwidth is 10 ㎐ for Average detection (AV) at frequency above 1 ㎓. 6.3.2. Test procedures for conducted spurious emissions All data rates and modes were investigated for conducted spurious emissions. Only the conducted emissions of the configuration that produced the worst case emissions are reported in this section. Per the guidance of KDB 558074, section 5.4.1.1, the reference level for out of band emissions is established from the plots of this section since the band edge emissions are measured with a RBW of 100 ㎑. This reference level is then used as the limit in subsequent plots for out of band spurious emissions shown in section 4.4.4. The limit for out of band spurious emission at the band edge is 30 ㏈ below the fundamental emission level measured in a 100 ㎑ bandwidth. Page : (11) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 6.4. Test results 6.4.1. Radiated spurious emissions (9 kHz to 30 MHz) The frequency spectrum from 9㎑ to 30㎒ was investigated. Emission levels are not reported muchlower than the limits by over 20 ㏈. All reading values are peak values. To get a maximum emission levels from the EUT, the EUT was moved throughout the XY, XZ, and YZ planes. Test mode : Bluetooth LE A. Lowest Ch. (2 402 MHz) Radiated emissions Ant. Correction factors Total Limit Duty Frequency Reading Detector Ant. factor Amp+CL Actual Limit Margin Pol. factor (MHz) (dBuV) Mode (dB/m) (dB) (dBuV/m) (dBuV/m) (dB) (dB) No other emissions were detected at a level greater than 20dB below limit. B. Middle Ch. (2 440 MHz) Radiated emissions Ant. Correction factors Total Limit Duty Frequency Reading Detector Ant. factor Amp+CL Actual Limit Margin Pol. factor (MHz) (dBuV) Mode (dB/m) (dB) (dBuV/m) (dBuV/m) (dB) (dB) No other emissions were detected at a level greater than 20dB below limit. C. Highest Ch. (2 480 MHz) Radiated emissions Ant. Correction factors Total Limit Duty Frequency Reading Detector Ant. factor Amp+CL Actual Limit Margin Pol. factor (MHz) (dBuV) Mode (dB/m) (dB) (dBuV/m) (dBuV/m) (dB) (dB) No other emissions were detected at a level greater than 20dB below limit. ※Remark 1. Actual = Reading + Ant. factor + CL (Cable loss) 2. Distance extrapolation factor = 40 log (specific distance / test distance) (dB) 3. Limit line = specific Limits (dBuV) + Distance extrapolation factor 4. 15.31 Measurement standards. The amplitude of spurious emissions from intentional radiators and emissions from unintentional radiators which are attenuated more than 20 dB below the permissible value need not be reported unless specifically required elsewhere in this part. Page : (12) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 6.4.2. Radiated spurious emissions (30 MHz to 1 000 MHz) The frequency spectrum from 30 ㎒ to 1 000 ㎒ was investigated. Emission levels are not reported muchlower than the limits by over 20 ㏈. All reading values are peak values. To get a maximum emission levels from the EUT, the EUT was moved throughout the XY, XZ, and YZ planes. Test mode : Bluetooth LE A. Lowest Ch. (2 402 MHz) Radiated emissions Ant. Correction factors Total Limit Duty Frequency Reading Detector Ant. factor Amp+CL Actual Limit Margin Pol. factor (MHz) (dBuV) Mode (dB/m) (dB) (dBuV/m) (dBuV/m) (dB) (dB) No other emissions were detected at a level greater than 20dB below limit. B. Middle Ch. (2 440 MHz) Radiated emissions Ant. Correction factors Total Limit Duty Frequency Reading Detector Ant. factor Amp+CL Actual Limit Margin Pol. factor (MHz) (dBuV) Mode (dB/m) (dB) (dBuV/m) (dBuV/m) (dB) (dB) No other emissions were detected at a level greater than 20dB below limit. C. Highest Ch. (2 480 MHz) Radiated emissions Ant. Correction factors Total Limit Duty Frequency Reading Detector Ant. factor Amp+CL Actual Limit Margin Pol. factor (MHz) (dBuV) Mode (dB/m) (dB) (dBuV/m) (dBuV/m) (dB) (dB) No other emissions were detected at a level greater than 20dB below limit. ※Remark 1. Actual = Reading + Ant. factor + CL (Cable loss) 2. 15.31 Measurement standards. The amplitude of spurious emissions from intentional radiators and emissions from unintentional radiators which are attenuated more than 20 dB below the permissible value need not be reported unless specifically required elsewhere in this part. Page : (13) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 6.4.3. Radiated spurious emissions & Bandedge (Above 1 000 MHz) The frequency spectrum above 1 000 ㎒was investigated. Emission levels are not reported much lower thanthe limits by over 20 ㏈. To get a maximum emission levels from the EUT, the EUT was moved throughout the XY, XZ, and YZ planes. Test mode : Bluetooth LE A. Lowest Ch. (2 402 MHz) Radiated emissions Ant. Correction factors Total Limit Duty Frequency Reading Detector Ant. factor Amp+CL Actual Limit Margin Pol. factor (MHz) (dBuV) Mode (dB/m) (dB) (dBuV/m) (dBuV/m) (dB) (dB) *2 330.43 37.10 Peak H 28.82 39.03 - 26.89 74.00 47.11 *2 318.59 56.29 Peak V 28.82 39.03 - 27.26 74.00 46.74 Above 3 000 MHz Not detected B. Middle Ch. (2 440 MHz) Radiated emissions Ant. Correction factors Total Limit Duty Frequency Reading Detector Ant. factor Amp+CL Actual Limit Margin Pol. factor (MHz) (dBuV) Mode (dB/m) (dB) (dBuV/m) (dBuV/m) (dB) (dB) No other emissions were detected at a level greater than 20dB below limit. ※Remark 1. Measuring frequencies from 1 ㎓ to the 10th harmonic of highest fundamental Frequency. 2. Radiated emissions measured in frequency above 1 000 ㎒ were made with an instrument usingpeak/average detector mode. 3. Average measurement did not take place because the peak data did not exceed Average Limit. 4. Actual = Reading + Ant. factor- Amp + CL (Cable loss) 5. 15.31 Measurement standards. The amplitude of spurious emissions from intentional radiators and emissions from unintentional radiators which are attenuated more than 20 dB below the permissible value need not be reported unless specifically required elsewhere in this part. 6. * is Restricted band. Page : (14) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) C. Highest Ch. (2 480 MHz) Radiated emissions Ant. Correction factors Total Limit Duty Frequency Reading Detector Ant. factor Amp+CL Actual Limit Margin Pol. factor (MHz) (dBuV) Mode (dB/m) (dB) (dBuV/m) (dBuV/m) (dB) (dB) *2 488.22 36.84 Peak H 28.82 39.03 - 26.63 74.00 47.37 *2 485.97 36.24 Peak V 28.82 39.03 - 26.03 74.00 47.97 Above 3 000 MHz Not detected ※Remark 1. Measuring frequencies from 1 ㎓ to the 10th harmonic of highest fundamental Frequency. 2. Radiated emissions measured in frequency above 1 000 ㎒ were made with an instrument usingpeak/average detector mode. 3. Average measurement did not take place because the peak data did not exceed Average Limit. 4. Actual = Reading + Ant. factor- Amp + CL (Cable loss) 5. 15.31 Measurement standards. The amplitude of spurious emissions from intentional radiators and emissions from unintentional radiators which are attenuated more than 20 dB below the permissible value need not be reported unless specifically required elsewhere in this part. 6. * is Restricted band. Page : (15) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 6.4.4. Test plot (Conducted spurious emissions & Bandedge) Test mode : Bluetooth LE A.1. Lowest Ch. (2 402 MHz)_Band edge A.2. Lowest Ch. (2 402 MHz)_Spurious emissions Page : (16) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) B.1. Middle Ch. (2 440 MHz)_Spurious emissions C.1. Highest Ch. (2 480 MHz)_ Band edge Page : (17) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) C.2. Highest Ch. (2 480 MHz)_Spurious emissions Page : (18) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 7. 6dB bandwidth 7.1. Test setup EUT Spectrum analyzer 7.2. Limit According to §15.247(a)(2), systems using digital modulation techniques may operate in the 902~928 ㎒, 2 400~2 483.5 ㎒, and 5 725~5 825 ㎒ bands. The minimum of 6 ㏈ Bandwidth shall be at least 500 ㎑ 7.3. Test procedure 1. The 6㏈ band width was measured with a spectrum analyzer connected to RF antenna connector(conducted measurement) while EUT was operating in transmit mode at the appropriate centerfrequency. The analyzer center frequency was set to the EUT carrier frequency, using the analyzer.Display Line and Marker Delta functions, the 6㏈ band width of the emission was determined. 2. The bandwidth of the fundamental frequency was measured with the spectrum analyzer using RBW = 100㎑,VBW≥ 3 x RBW, Span= 2times the DTS bandwidth Detector= peak, Trace = max hold, Sweep=auto couple 7.4. Test results Frequency(㎒) 6 ㏈ bandwidth(㎒) 2 402 0.74 2 440 0.72 2 480 0.74 Page : (19) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 7.4.1 Test plot A.1. Lowest Ch. (2 402 MHz)_6dB Bandwidth B.2. Middle Ch. (2 440 MHz)_6dB Bandwidth Page : (20) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) C.3. Highest Ch. (2 480 MHz)_6dB Bandwidth Page : (21) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 8. Maximum peak conducted output power 8.1. Test setup EUT Spectrum Analyzer 8.2. Limit The maximum peak output power of the intentional radiator shall not exceed the following: 1. §15.247(a)(1), Frequency hopping systems shall have hopping channel carrier frequencies separated by aminimum of 25 ㎑or the 6 ㏈ bandwidth of the hopping channel, whichever is greater, provided thesystems operate with an output power no greater than 125 ㎽ 2. §15.247(b)(1), For frequency hopping systems operating in the 2400–2483.5 ㎒ employing atleast 75non-overlapping hopping channels, and all frequency hopping systems in the 5725– 5 805 ㎒ band: 1Watt. 8.3. Test procedure Maximum Peak Conducted Output Power is measured using the following procedure (RBW ≥ DTS bandwidth). 1. Set the RBW ≥ DTS bandwidth. 2. Set VBW ≥ 3 x RBW. / Set span ≥ 3 x RBW. 4. Sweep time = auto couple 5. Detector = peak 6. Trace mode = max hold 7. Allow trace to fully stabilize 8. Use peak marker function to determine the peak amplitude level. 8.4. Test results Frequency(㎒) Conducted power (㏈m) Limit (㏈m) 2 402 -17.05 2 440 -16.77 30 2 480 -17.47 Page : (22) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 8.4.1 Test plot A. Lowest Ch. (2 402 MHz) B. Middle Ch. (2 440 MHz) Page : (23) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) C. Highest Ch. (2 480 MHz) Page : (24) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 9. Peak power spectral density 9.1. Test setup EUT Spectrum analyzer 9.2. Limit < 8dBm @ 3kHz BW 9.3. Test procedure (PKPSD) 1. The RF power output was measured with a Spectrum analyzer connected to the RF Antenna connector(conducted measurement) while EUT was operating in transmit mode at the appropriate center frequency,A spectrum analyzer was used to record the shape of the transmit signal. 2. The bandwidth of the fundamental frequency was measured with the spectrum analyzer using; Span = 1.5 times the DTS bandwidth RBW = 3㎑ ≤ RBW ≤100㎑ VBW ≥ 3 x RBW,Sweep = Auto couple Detectorfunction = peak, Trace = max hold 9.4. Test results Frequency(㎒) Peak output power(㏈m) Limit (㏈m) 2 402 -32.08 2 440 -31.85 8 2 480 -32.63 Page : (25) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 9.4.1 Test plot A. Lowest Ch. (2 402 MHz) B. Middle Ch. (2 440 MHz) Page : (26) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) C. Highest Ch. (2 480 MHz) Page : (27) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 10. AC Conducted power line test 10.1. Test setup AC Main Adaptor EUT 10.2. Limit According to §15.107(a) for an intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power lineon any frequency or frequencies, within the band 150 ㎑ to 30 ㎒, shall not exceed the limitsin the following table, as measured using a 50 uH/50ohm line impedance stabilization network(LISN). Compliance with the provision of this paragraph shall on the measurement of the radio frequencyvoltage between each power line and ground at the power terminal. The lower applies at the boundary between the frequencies ranges. Conducted limit (㏈㎶/m) Frequency of Emission (㎒) Quasi-peak Average 0.15 – 0.50 66-56* 56-46* 0.50 – 5.00 56 46 5.00 – 30.0 60 50 ※Remark Decreases with the logarithm of the frequency. Page : (28) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 10.3. Test procedure The test procedure is performed in a 6.5 m × 3.6 m × 3.6 m (L×W×H) shielded room. The EUTalong with its peripherals were placed on a 1.0m(W)× 1.5m(L) and 0.8m in heightwooden table and the EUT was adjusted to maintain a 0.4 meter space from a verticalreference plane. The EUT was connected to power mains through a line impedancestabilization network (LISN) which provides 50 ohm coupling impedance for measuringinstrument and the chassis ground was bounded to the horizontal ground plane of shieldedroom. All peripherals were connected to the second LISN and the chassis ground alsobounded to the horizontal ground plane of shielded room. The excess power cablebetween the EUT and the LISN was bundled. The power cables of peripherals wereunbundled. All connecting cables of EUT and peripherals were moved to find themaximum emission. 10.4. Test results Frequency range: 0.15 ㎒ ~ 30 ㎒ Measured bandwidth: 9 ㎑ Frequency QuasiPeak CAverage Limit Margin Meas. Bandwidth Line PE Corr. (MHz) (dBuV) (dBuV) (dBuV) (dB) Time (kHz) (dB) (ms) 0.51 33.72 --- 56.00 22.28 7000.0 9.00 N GND 9.99 0.51 --- 7.58 46.00 38.42 7000.0 9.00 N GND 9.99 0.61 --- 6.25 46.00 39.75 7000.0 9.00 N GND 10.00 0.62 25.42 --- 56.00 30.58 7000.0 9.00 N GND 10.00 0.77 36.14 --- 56.00 19.86 7000.0 9.00 L1 GND 10.01 0.77 --- 8.22 46.00 37.78 7000.0 9.00 N GND 10.00 0.78 --- 8.95 46.00 37.05 7000.0 9.00 N GND 10.00 0.78 36.49 --- 56.00 19.51 7000.0 9.00 L1 GND 10.01 14.62 --- 11.90 50.00 38.10 7000.0 9.00 L1 GND 11.28 14.71 26.12 --- 60.00 33.88 7000.0 9.00 N GND 10.95 15.04 --- 9.97 50.00 40.03 7000.0 9.00 L1 GND 11.32 15.13 26.12 --- 60.00 33.88 7000.0 9.00 N GND 10.97 ※Remark Line(L1): Hot Line(N): Neutral Page : (29) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 10.4.1 Test plot 80 70 QP Class B 60 AV Class B 50 40 Level in dBuV 30 20 10 0 -10 150k 300 400 500 800 1M 2M 3M 4M 5M 6 8 10M 20M 30M Frequency in Hz Page : (30) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 11. Antenna requirement 11.1. Standard applicable For intentional device, according to FCC 47 CFR Section §15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. And according to FCC 47 CFR Section §15.247 (b) if transmitting antennas of directional gain greater than 6㏈ i are used. 11.2. Antenna connected construction Antenna used in this product is PCB antenna, Antenna gain is 0.8 ㏈ i. Page : (31) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 12. RF exposure evaluation 12.1. 10.1 Environmental evaluation and exposure limit according to FCC CFR 47 part 1, 1.1307(b), 1.1310 According to §15.247(e)(i) and §1.1307(b)(1), systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. According to KDB 447498 (2)(a)(i) Limits for maximum permissible exposure (MPE) Frequency range Electric field Magnetic field Power density Average time (㎒) strength(V/m) strength (A/m) (㎽/㎠) (A) Limits for Occupational / Control exposures 300 – 1 500 -- -- F/300 6 1 500 – 100 000 -- -- 5 6 (B) Limits for General Population / Uncontrol Exposures 300 – 1 500 -- -- F/1 500 6 1 500 – 100 000 -- -- 1 30 12.2. Friis transmission formula : Pd=(Pout*G)\(4*pi*R2) Where Pd= Power density in ㎽/㎠ Pout=output power to antenna in ㎽ G= Numeric gain of the antenna relative to isotropic antenna Pi=3.1416 R= distance between observation point and center of the radiator in cm Pd the limit of MPE, 1 ㎽/㎠. If we know the maximum gain of the antenna and total power input to the antenna, through the calculation, we will know the distance where the MPE limit is reached. Page : (32) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.

MOVON CORPORATION Report Number: MOV-19-RF-I029(1) 12.3 RF exposure evaluation Test Item ：RF Exposure evaluation data Test Mode ：Normal operation 12.3RF Exposure Compliance Requirement 12.3.1 Standard Requirement According to KDB447498D01 General RF Exposure Guidance v06 4.3.1. Standalone SAR test exclusion considerations Unless specifically required by the published RF exposure KDB procedures, standalone 1-g head or body and 10-g extremity SAR evaluation for general population exposure conditions, by measurement or numerical simulation, is not required when the corresponding SAR Exclusion Threshold condition, listed below, is satisfied. 12.3.2 Limits The 1-g and 10-g SAR test exclusion thresholds for 100 MHz to 6 GHz at test separation distances ≤ 50 mm are determined by: [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] ≤ 3.0 for 1-g SAR and ≤ 7.5 for 10-g extremity SAR, where f(GHz) is the RF channel transmit frequency in GHz Power and distance are rounded to the nearest mW and mm before calculation The result is rounded to one decimal place for comparison The test exclusions are applicable only when the minimum test separation distance is ≤ 50 mm and for transmission frequencies between 100 MHz and 6 GHz. When the minimum test separation distance is < 5 mm, a distance of 5 mm is applied to determine SAR test exclusion 12.3.3 EUT RF Exposure Operation mode: BLE The Max Conducted Peak Output Power is -16.77dBm in Highest channel(2.440 GHz) Target power & Tolerance Target power:-17.00 dBm Tolerance: ±1.00 dBm -16.00dBm logarithmic terms convert to numeric result is nearly 0.025 mW According to the formula. calculate the Peak Output Power test result: General RF Exposure = (0.025 mW / 5 mm ) x √2.440 GHz = 0.0078 So the SAR report is not required. ※ Remark [(max. power of channel, including tune-up tolerance, mW)/(min. test separation distance, mm)] · [√f(GHz)] Page : (33) of (33) The results shown in this test report refer only to the sample(s) tested unless otherwise stated.This test report cannot be reproduced, except in full, without the written approval ofMOVON CORPORATION.


Document Created: 2019-05-04 05:12:30
Document Modified: 2019-05-04 05:12:30
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC