Module Approval Letter

FCC ID: 2ARGX-WIFIM

Cover Letter(s)

Download: PDF
FCCID_4249352

Modular Approval Letter 2019-04-10 Applicant: Align Technology Inc. Application Address: 2820 Orchard Parkway San Jose, CA 95134 United States Product Name: WiFi Module Model Name: WifiM FCC ID: 2ARGX-WIFIM Section 15.212 Modular Transmitters Request for Modular Approval Request for Limited Modular Approval Single Modular Approval Requirements: Comply( Item Requirements EUT Conditions Y/N) The radio elements of the modular transmitter must have their own shielding. The physical All components are in 1 Yes crystal and tuning capacitors may be located shielding. external to the shielded radio elements. The modular transmitter must have buffered modulation/data inputs (if such inputs are provided) to ensure that the module will 2 Yes, all set. Yes comply with part 15.247 requirements under conditions of excessive data rates or over‐modulation. The modular transmitter must have its own 3 Yes, all set. Yes power supply regulation.

Comply( Item Requirements EUT Conditions Y/N) The modular transmitter must comply with the antenna and transmission system requirements of §15.203, §15.204(b) and §15.204(c). The antenna must either be permanently attached or employ a “unique” antenna coupler 4 (at all connections between the module and Yes, all set. Yes the antenna, including the cable). The “professional installation” provision of §15.203 is not applicable to modules but can apply to limited modular approvals under paragraph (b) of this section. The modular transmitter must be tested in a stand‐alone configuration, i.e., the module must not be inside another device during testing for compliance with part §15.247 requirements. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in §15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be 5 Yes, all set. Yes. marketed with the module (see §15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see §15.31(i)).

Comply( Item Requirements EUT Conditions Y/N) If using a permanently affixed label, the modular transmitter must be labeled with its own FCC identification number, and, if the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module 6 Yes, all set. Yes FCC ID: 2ARGX-WIFIM Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. The modular transmitter must comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate 7 Yes, all set. Yes instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization.

Comply( Item Requirements EUT Conditions Y/N) The modular transmitter must comply with any 8 applicable RF exposure requirements in its final Yes, all set. Yes configuration. Sincerely, Edi Fridman/Expert System Engineer (408)470-1000 2820 Orchard Parkway San Jose, CA 95134 United States


Document Created: 2019-04-24 02:30:30
Document Modified: 2019-04-24 02:30:30
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC