Test Report

FCC ID: 2ARG7DPHDI200

Test Report

Download: PDF
FCCID_4135868

’d \ ln «‘a /\ \\\‘\\ 294 Pnd > Q// * ACCREDITED \ \/’ se/7/\\\\&“ ulutabs TesTING CERTH4338. 0 FCC Part 15B TEST REPORT Report No.: STS1812078E01 Issued for Shenzhen DophiGo loT Technology Co., Ltd. 16/F, Building B1, Nanshan Park, No.1001 Xueyuan Ave, Nanshan District, Shenzhen, China Product Name: DophiGo Indoor Chime Brand Name: DophiGo Model Name: DPH—DI—200 Series Model: DPH—Dl—xxx (x on behalf of 0—9) FCC ID: 2ARG7ZDPHDI200 Test Standard: FCC 47 CFR Part 15: Subpart B Any reproduction of this document must be done in full. No single part of this docume permission from STS, All Test Data Presented in this report is only applicable to presente Shenzhen STS Test Services Co., Ltd. 1/F., Building B, Zhuoke Science Park, No.190, Chongaqing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China TEL: +86—755 3688 6288 FAX: +86—755 3688 6277 E—mail:sts@stsapp.com

) mus» I mmm» 4 TEST RESULT CERTIFICATION Applicant‘s Name .................: Shenzhen DophiGo loT Technology Co., Ltd. Address . 16/F, Building B1, Nanshan Park, No.1001 Xueyuan Ave, Nanshan """"""""""""""""""" District, Shenzhen, China Manufacture‘s Name ............: Shenzhen DophiGo loT Technology Co., Ltd. ee 16/F, Building B1, Nanshan Park, No.1001 Xueyuan Ave, Nanshan District, Shenzhen, China Product Description .............: Product Name ........................:.. DophiGo Indoor Chime Brand Name..........................: DophiGo Model Name ...........c.c.c.c.c..cc= DPH—DI—200 Series Model |........................:. DPH—Dl—xxx (x on behalf of 0—9) Standards..............................:_FCC 47 CFR Part 15: Subpart B Test Procedure.....................: ANSI C63.4—2014 This device described above has been tested by STS, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of STS, this document may be altered or revised by STS, personal only, and shall be noted in the revision of the document. DAt@ Of T@St........2 .0. ce e reerree e : Date of Performance of Tests ............... : 18 Dec. 2018~22 Dec. 2018 DAt@ Of ISSUQ ......2.00.00 00e e e : 23 Dec. 2018 TeSt R@SUI ... 22220000000 e : Pass Compiled by : m I\C }@% D:%g { Mickey Deng ) . aZP = . Technical Manager _: CAesfie® . Yams { Chopin Xiao ) Authorized Signatory : \/TM(J ( Vita Li 1/F., Building B, Zhuoke Science Park, No.190, Chongging Road, Fuyong Street, Bao‘an District, Shenzhen, Guangdong, China Shenzhen STS Test SerViceS CO. Ltd Tel: +86—755 3688 6288 Faxc+ 86—755 3688 6277 Hitp‘//www.stsapp.com E~mail: sts@stsapp.com

P aas. I tams \— Page 3 of 20 Report No.: STS1812078E01 Table of Contents 1. SUMMARY OF THE TEST RESULTS a 1.1 TEST FACTORY a 1.2 MEASUREMENT UNCERTAINTY a 2. GENERAL INFORMATION o 2.1 GENERAL DESCRIPTION OF THE EUT ~_OG 2.2 DESCRIPTION OF THE TEST MODES 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF THE SYSTEM TESTEDT7 2.4 DESCRIPTION OF THE SUPPORT UNITS 8 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS 9 3. EMC EMISSION TEST 10 3.1 CONDUCTED EMISSION MEASUREMENT 10 3.2 RADIATED EMISSION MEASUREMENT 14 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services CO., Ltd. Tel: + 86—785 3688 6288 Faxc+ 86—755 3688 6277 Hitp://www.stsapp.com E~mail: sts@stsapp.com

Page 4 of 20 Report No.: STS1812078E01 Revision History Rev. Issue Date Report No. Effect Page Contents 00 23 Dec. 2018 STS1812078E01 ALL Initial Issue

Page 5 of 20 Report No.: STS1812078E01 1. SUMMARY OF THE TEST RESULTS Test procedures according to the technical standards: EMISSION Standard Item Result Remarks Conducted Emission PASS Meet Class B limit FCC 47 CFR Part 15 Subpart B Radiated Emission PASS Meet Class B limit NOTE: (1) “ N/A” denotes test is not applicable in this Test Report 1.1 TEST FACTORY Company Name: Shenzhen STS Test Services Co. Ltd. 1/F., Building B, Zhuoke Science Park, No.190, Chongqing Road, Address: Fuyong Street, Bao’an District, Shenzhen, Guangdong, China Telephone: +86-755 3688 6288 Fax: +86-755 3688 6277 FCC Registration No.: 625569 Registration No.: IC Registration No.: 12108A; A2LA Certificate No.: 4338.01; 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y ± U, where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2, providing a level of confidence of approximately 95 %。 No. Item Uncertainty 1 Conducted Emission (9KHz-150KHz) ±3.18dB 2 Conducted Emission (150KHz-30MHz) ±2.70dB 3 All emissions,radiated(<1G) 9KHz-30MHz ±2.50dB 4 All emissions,radiated(<1G) 30MHz-200MHz ±3.43dB 5 All emissions,radiated(<1G) 200MHz-1000MHz ±3.57dB 6 All emissions,radiated(>1G) ±4.13dB

N\ \/ Page 6 of 20 Report No.: STS1812078E01 2. GENERAL INFORMATION 2.1 GENERAL DESCRIPTION OF THE EUT Product Name DophiGo Indoor Chime Brand Name DophiGo Model Name DPH—D1—200 Series Model DPH—DI—xxx (x on behalf of 0—9) Where x = 0—9, indicating that the enclosure has multiple Model Difference colors and different areas of sale, without compromising safety and EMC performance. Test Sample Number 181218030 Frequency Bands 434Mhz Modulation Mode FSK Power Source Input: AC110—220V, Rated Power: 1 W, Frequency: 50/60Hz Hardware Version Number DPHOO1_SY5ON76_VO.2 Software Version Number fw_dph_vdoorbell_in_meu_v1.0.0 Note: For a more detailed features description, please refer to the manufacturer‘s specifications or the User‘s Manual. 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. Tel: + 86—785 3688 6288 Faxc+ 86—755 3688 6277 Hitp://www.stsapp.com E—mail: sts@stsapp.com

Page 7 of 20 Report No.: STS1812078E01 2.2 DESCRIPTION OF THE TEST MODES To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively. Pretest Mode Description Mode 1 RX For Conducted Test Final Test Mode Description Mode 1 RX For Radiated Test Final Test Mode Description Mode 1 RX NOTE: The test modes were carried out for all operation modes. Only worst case will be show in this report. 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF THE SYSTEM TESTED AC Plug EUT

Page 8 of 20 Report No.: STS1812078E01 2.4 DESCRIPTION OF THE SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Accessories equipment Item Equipment Mfr/Brand Model/Type No. N/A N/A N/A N/A Auxiliary equipment Item Equipment Mfr/Brand Model/Type No. N/A N/A N/A N/A Cable Item Type Shielded Type Ferrite Core Length N/A N/A N/A N/A N/A Note: (1) The support equipment was authorized by Declaration of Confirmation. (2) For detachable type I/O cable should be specified the length in cm in『Length』column. (3) “YES” is means “shielded” “with core”; “NO” is means “unshielded” “without core”.

Page 9 of 20 Report No.: STS1812078E01 2.5 EQUIPMENTS LIST FOR ALL TEST ITEMS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Radiation Test equipment Kind of Equipment Manufacturer Type No. Serial No. Last Calibration Calibrated Until EMI Test Receiver R&S ESCI 101427 2018.10.13 2019.10.12 Bilog Antenna TESEQ CBL6111D 45873 2017.11.02 2020.11.01 SCHWARZB Horn Antenna BBHA 9120D 9120D-1343 2018.10.19 2021.10.18 ECK LNPA-01018G- Pre-mplifier(1G-18G) SKET SK2018080901 2018.10.13 2019.10.12 45 Pre-mplifier(0.1M-3G EM EM330 060665 2018.07.10 2019.07.09 Hz) Spectrum Analyzer Agilent N9020A MY49100060 2018.10.13 2019.10.12 RE Cable (9K-1G) N/A R01 N/A 2018.10.13 2019.10.12 RE Cable (1G-18G) N/A R02 N/A 2018.10.13 2019.10.12 Temperature & Mieo HH660 N/A 2018.10.11 2019.10.10 Humidity Horn A-INFO LB-180400-KF J211020657 2018.03.11 2021.03.10 Antenna(18-40GHz) Conduction Test equipment Kind of Equipment Manufacturer Type No. Serial No. Last Calibration Calibrated Until EMI Test Receiver R&S ESCI 101427 2018.10.13 2019.10.12 LISN R&S ENV216 101242 2018.10.11 2019.10.10 LISN ETS 3810/2NM 00023625 2018.10.11 2019.10.10 Absorbing Clamp R&S MDS-21 100668 2018.10.17 2019.10.16 CE Cable N/A C01 N/A 2018.10.13 2019.10.12 Temperature & Mieo HH660 N/A 2018.10.11 2019.10.10 Humidity

Page 10 of 20 Report No.: STS1812078E01 3. EMC EMISSION TEST 3.1 CONDUCTED EMISSION MEASUREMENT 3.1.1 POWER LINE CONDUCTED EMISSION Limits Conducted Emission Limits (dBuV) FREQUENCY (MHz) Class A Class B Quasi-peak Average Quasi-peak Average 0.15 -0.5 79.00 66.00 66 - 56 * 56 - 46 * 0.50 -5.0 73.00 60.00 56.00 46.00 5.0 -30.0 73.00 60.00 60.00 50.00 Note: (1) The tighter limit applies at the band edges. The limit of " * " marked band means the limitation decreases linearly with the (2) logarithm of the frequency in the range. The following table is the setting of the receiver Receiver Parameters Setting Attenuation 10 dB Start Frequency 0.15 MHz Stop Frequency 30 MHz IF Bandwidth 9 kHz

Page 11 of 20 Report No.: STS1812078E01 3.1.2 TEST PROCEDURE a. The EUT was 0.8 meters from the horizontal ground plane and 0.4 meters from the vertical ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long. c. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. d. For the actual test configuration, please refer to the related Item –EUT Test Photos. 3.1.3 DEVIATION FROM TEST STANDARD No deviation 3.1.4 TEST SETUP Vertical Reference Ground Plane Test Receiver EUT 40cm 80cm LISN Horizontal Reference Ground Plane Note: 1.Support units were connected to second LISN. 2.Both of LISNs (AMN) are 80 cm from EUT and at least 80 cm from other units and other metal planes support. units. 3.1.5 EUT OPERATING CONDITIONS The EUT was configured for testing in a typical fashion (as a customer would normally use it). The EUT has been programmed to continuously transmit during test. This operating condition was tested and used to collect the included data.

P aas. I tams \— Page 12 of 20 Report No.: STS1812078E01 3.1.6 TEST RESULTS Temperature: 24.7 °C Relative Humidity: (56% Phase: L Test Mode: Mode 1 Test Voltage: AC 120V/60Hz Frequenc Readin Gorrect Resul Limi Margin No. (I\C;IHZ) Y (dBuV)g Fa‘g‘)’r (dgsffi/t) (dBu\t/) (289) Detector 1 0.2660 34.63 20.56 55.19 61.24 —6.05 QaP 2 0.2660 14.97 20.56 35.53 51.24 —15.71 AVG 3 0.3580 33.18 20.59 53.77 58.77 —5.00 QaP 4 0.3580 17.22 20.59 37.81 48.77 —10.96 AVG 5 0.4460 32.00 20.49 52.49 56.95 ~4.46 QaP 6 0.4460 19.22 20.49 39.71 46.95 —7.24 AVG 7 1.0260 27.57 2016 47.73 56.00 —8.27 QaP 8 1.0260 2217 2016 42.33 46.00 —3.67 AVG 9 3.2100 26.11 19.97 46.08 56.00 —9.92 QaP 10 3.2100 21.19 19.97 41.16 46.00 ~4.84 AVG 11 5.3500 24.87 19.93 44.80 60.00 —15.20 QaP 12 5.3500 19.15 19.93 39.08 50.00 —10.92 AVG Remark: 1. All readings are Quasi—Peak and Average values. 2. Margin = Result (Result =Reading + Factor )—Limit 3. Factor= Cable Loss +Antenna Factor—Amplifier Gain 100.0 dBu¥ Limit1: — Limit2: — \ po———————————— wM 50 wl g\‘i "\:‘”l'! Wmi peak wU;h"\u AvG 0.0 0.150 0.5 [MHz] 30.000 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. Tel: + 86—785 3688 6288 Faxc+ 86—755 3688 6277 Hitp://www.stsapp.com E—mail: sts@stsapp.com

NA \/ Page 13 of 20 Report No.: STS1812078E01 Temperature: 24.7 °C Relative Humidity: (56% Phase: N Test Mode: Mode 1 Test Voltage: AC 120V/60Hz . Correct im . Frequency Reading Result Limit Margin No. (MH2z) (dBuV) Fa‘g‘)’r (dBuV) (dBuV) (dB) Detector 1 0.2220 33.99 20.34 54.33 62.74 —8.41 QaP 2 0.2220 16.45 20.34 36.79 52.74 —15.95 AVG 3 0.3140 33.41 20.69 54.10 59.86 —5.76 QaP 4 0.3140 18.12 20.69 38.81 49.86 —11.05 AVG 5 0.9380 30.04 20.18 50.22 56.00 —5.78 QaP 6 0.9380 24.26 20.18 44.44 46.00 —1.56 AVG 7 3.2580 28.38 19.98 48.36 56.00 —7.64 QaP 8 3.2580 22.01 19.98 41.99 46.00 —4.01 AVG 9 5.4420 27.08 19.92 47.00 60.00 —13.00 QaP 10 5.4420 21.17 19.92 41.09 50.00 —8.91 AVG 11 14.4580 23.94 19.99 43.93 60.00 —16.07 QaP 12 14.4580 8.04 19.99 28.03 50.00 —21.97 AVG Remark: 1. All readings are Quasi—Peak and Average values. 2. Margin = Result (Result =Reading + Factor )—Limit 3. Factor= Cable Loss +Antenna Factor—Amplifier Gain 100.0 dBu¥ Limit1: — Limit2: — —————————— 50 f IL | oluce j L NLL ult § U ul iNh (RST lui) P : | ||‘ L ‘ ’I‘ dnR ||i|“”'““”\\ peak AVG 0.0 0.150 0.5 [MHz] 5 30.000 Note: The test voltage is 100—240V, both of which have assessment tests, and the worst test data is in the report. 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. Tel: + 86—785 3688 6288 Faxc+ 86—755 3688 6277 Hitp://www.stsapp.com E—mail: sts@stsapp.com

Page 14 of 20 Report No.: STS1812078E01 3.2 RADIATED EMISSION MEASUREMENT 3.2.1 Radiated Emission Limits In case the emission fall within the restricted band specified on 15.105(a)&109(a) limit in the table below has to be followed. Frequencies Field Strength Measurement Distance (MHz) (micorvolts/meter) (meters) 30~88 100 3 88~216 150 3 216~960 200 3 Above 960 500 3 LIMITS OF THE RADIATED EMISSION MEASUREMENT Class A (dBuV/m) (at 3M) Class B (dBuV/m) (at 3M) FREQUENCY (MHz) PEAK AVERAGE PEAK AVERAGE Above 1000 80 60 74 54 Note: (1) The limit for radiated test was performed in the following: FCC PART 15B. (2) The tighter limit applies at the band edges. (3) Emission level (dBuV/m)=20log Emission level (uV/m). FREQUENCY RANGE OF THE RADIATED MEASUREMENT (For unintentional radiators) Highest frequency generated or Upper frequency of measurement used in the device Range (MHz) or on which the device operates or tunes (MHz) Below 1.705 30 1.705 – 108 1000 108 – 500 2000 500 – 1000 5000 5th harmonic of the highest frequency or 40 GHz, Above 1000 whichever is lower

Page 15 of 20 Report No.: STS1812078E01 Spectrum Parameter Setting Attenuation Auto Detector Peak Start Frequency 1000 MHz(Peak/AV) Stop Frequency 5th harmonic (Peak/AV) RB / VB (emission in restricted 30MHz to 1000MHz: 100 KHz / 300 KHz band) Above 1000MHz: 1 MHz / 3 MHz Receiver Parameter Setting Attenuation Auto 30MHz to 1000MHz: 100 KHz / 300 KHz Start ~ Stop Frequency Above 1000MHz: 1 MHz / 3 MHz 3.2.2 TEST PROCEDURE a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoic chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The height of antenna is varied from 1 meter to 4 meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1GHz. f. For the actual test configuration, please refer to the related Item –EUT Test Photos. Note: Both horizontal and vertical antenna polarities were tested and performed pretest to three orthogonal axis. The worst case emissions were reported 3.2.3 DEVIATION FROM TEST STANDARD No deviation

D 2 \/ Page 16 of 20 Report No.: STS1812078E01 3.2.4 TEST SETUP (A) Radiated Emission Test—Up Frequency 3OMHz~1GHz Ant. feed RX Antenna point Bm ——————#» Metal Full Soldered Ground Plane [~—~~] 86 Spectrum Analyzer /Receiver System Simulator (B) Radiated Emission Test—Up Frequency Above 1GHz Ant. feed RX Antenna +}+ [~——~) se Spectrum P Analyzer i lyzer Receiver System Simulator 3.2.5 EUT OPERATING CONDITIONS The EUT tested system was configured as the statements of 2.4 Unless otherwise a special operating condition is specified in the following during the testing. 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. Tel: + 86—785 3688 6288 Faxc+ 86—755 3688 6277 Hitp://www.stsapp.com E~mail: sts@stsapp.com

N\ \/ Page 17 of 20 Report No.: STS1812078E01 3.2.6 TEST RESULTS 30MHz —1000MHz Temperature: 24.6 °C Relative Humidity: (55% Phase: Horizontal Test Mode: Mode 1 Test Voltage: AC 120V/60Hz No. Frt(a[\c;ltlj_'ezr;cy F({Sgfll\r;)g Fai(t)é[e(gts) (Egj\gl/tri) (déhr(]/i}m) M(irsg)i” Detector 1 36.6375 30.78 —14.59 16.19 40.00 —23.81 aP 2 164.3301 36.69 —18.86 17.83 43.50 —25.67 aP 3 225.3080 47.44 —18.77 28.67 46.00 —17.33 aP 4 319.9370 52.46 1417 38.29 46.00 —7.71 aP 5 355.4273 50.04 —13.34 36.70 46.00 —9.30 aP 6 968.9338 28.66 —0.13 28.53 54.00 —25.47 aP Remark: 1. All readings are Quasi—Peak. 2. Margin = Result (Result =Reading + Factor )—Limit 3. Factor= Cable Loss +Antenna Factor—Amplifier Gain 80.0 dBu¥/m Limit1: — Margin: — 30.000 40 50 o 70 80 [MHz] 300 400 500 600 700 1000.000 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. Tel: + 86—785 3688 6288 Faxc+ 86—755 3688 6277 Hitp://www.stsapp.com E—mail: sts@stsapp.com

N\ \/ Page 18 of 20 Report No.: STS1812078E01 Temperature: 24.6 °C Relative Humidity: (55% Phase: Vertical Test Mode: Mode 1 Test Voltage: AC 120V/60Hz Frequency Reading Correct Results Limit Margin No. (MHz) (dBuV) Factor (dB) (dBuv/im) (d@Buv/im) (as) Peector 1 36.8953 44.21 —14.73 29.48 40.00 —10.52 aP 2 47.4918 46.81 —20.19 26.62 40.00 —13.38 aP 3 75.7114 43.56 —23.30 20.26 40.00 —19.74 aP 4 222.9502 48.07 —18.93 29.14 46.00 —16.86 aP 5 325.5758 49.82 —14.12 35.70 46.00 —10.30 aP 6 982.6200 28.42 —0.14 28.28 54.00 —25.72 aP Remark: 1. All readings are Quasi—Peak. 2. Margin = Result (Result =Reading + Factor )—Limit 3. Factor= Cable Loss +Antenna Factor—Amplifier Gain 80.0 dBu¥/m Limit1: — Margin: — 6 30.000 40 50 60 70 80 [MHz] 300 400 500 600 700 1000.000 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. Tel: + 86—785 3688 6288 Faxc+ 86—755 3688 6277 Hitp://www.stsapp.com E—mail: sts@stsapp.com

N\ \/ Page 19 of 20 Report No.: STS1812078E01 (1 GHz to 25GHz.) Temperature: 25 CC Relative Humidity: (69% Phase: Horizontal Test Mode: Mode 1 Test Voltage: AC 120V/60Hz Frequenc Results Limit Over Limit No. (l\C;|HZ) Y (dBuV/m) Factor (dB) (dBuV/m) (dB) Detector 1** 1282.000 24.06 —4.48 54.0 —29.94 AV 1 1282.000 34.57 —4.48 74.0 —39.43 Peak 2** 2410.000 31.52 0.80 54.0 —22.48 AV 2 2410.000 41.15 0.80 74.0 —32.85 Peak 3** 7510.000 26.64 10.59 54.0 —27.36 AV 3 7510.000 37.24 10.59 74.0 —36.76 Peak 4** 13660.000 41.89 23.37 54.0 412.11 AV 4 13660.000 51.26 23.37 74.0 —22.74 Peak 5** 16432.000 42.65 21.73 54.0 —11.35 AV 5 16432.000 51.95 21.73 74.0 —22.05 Peak 6** 21604.000 46.84 23.98 54.0 —7.16 AV 6 21604.000 57.02 23.98 74.0 —16.98 Peak Remark: 1. All readings are Peak and Average values. 2. Margin = Result (Result =Reading + Factor )—Limit 3. Factor= Cable Loss +Antenna Factor—Amplifier Gain REFCC Test CaseFCC 158 1GHz—25GHz level (dBuV/m) 1000 150 2000 MBS 3000 6000 100 2500 Zequency (MF) 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co.. +s Ltd + Tel: + 86—785 3688 6288 Faxc+ 86—755 3688 6277 Hitp://www.stsapp.com E—mail: sts@stsapp.com

N\ \/ Page 20 of 20 Report No.: STS1812078E01 Temperature: 25°C Relative Humidity: (69% Phase: Vertical Test Mode: Mode 1 Test Voltage: AC 120V/60Hz Frequenc Results Limit Over Limit No (I\C;IHz) Y (dBuV/m) Factor (dB) (dBuV/m) (dB) Detector 1** 2452.000 29.57 1.22 54.0 —24.43 AV 1 2452.000 40.10 1.22 74.0 —33.90 Peak 2** 7500.000 26.16 10.47 54.0 —27.84 AV 2 7500.000 35.76 10.47 74.0 —38.24 Peak 3** 13696.000 41.63 23.26 54.0 —12.37 AV 3 13696.000 51.81 23.26 74.0 —22.19 Peak 4** 16408.001 42.25 21.48 54.0 —11.75 AV 4 16408.001 52.32 21.48 74.0 —21.68 Peak 5** 21112.001 44.82 24.11 54.0 —9.18 AV 5 21112.001 56.16 24.11 74.0 —17.84 Peak 6** 24340.001 47 46 23.20 54.0 —6.54 AV 6 24340.001 57.16 23.20 74.0 —16.84 Peak Remark: 1. All readings are Peak and Average values. 2. Margin = Result (Result =Reading + Factor )—Limit 3. Factor= Cable Loss +Antenna Factor—Amplifier Gain REFCC Test GaseFCC 158 16Hz—256Hz level (dBuV/m) 1000 150 20 2835 300 6000 20000 25000 Frequency (VHz) Notes: 1. Measuring frequencies from 1 GHz to 25GHz. 2. Radiated emissions measured in frequency above 1000MHz were made with an instrument using Peak detector mode of the emission shown in Actual FS column. X K X XOKEND OF THE REPORT X X X% xOX 1/F.,, Building B, Zhuoke Science Park, No.190, Chongaing Road, Fuyong Street, Bac‘an District, Shenzhen, Guangdong, China Shenzhen STS Test Services Co., Ltd. Tel: + 86—785 3688 6288 Faxc+ 86—755 3688 6277 Hitp://www.stsapp.com E—mail: sts@stsapp.com


Document Created: 2019-01-11 11:45:27
Document Modified: 2019-01-11 11:45:27
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC