RF Exposure Info

FCC ID: 2ARD3-LA113

RF Exposure Info

Download: PDF
FCCID_4027192

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Report No.: SZEM180900842903 Fax: +86 (0) 755 2671 0594 Email: ee.shenzhen@sgs.com Page: 1 of 6 1 Cover page SAR Evaluation Report Application No.: SZEM1809008429CR(GZEM1809005285CR) Applicant: LEXON Address of Applicant: 91 avenue Jean Baptiste Clement 92100 Boulogne, France Manufacturer: LEXON Address of Manufacturer: 91 avenue Jean Baptiste Clement 92100 Boulogne, France Factory: LEXON Address of Factory: 91 avenue Jean Baptiste Clement 92100 Boulogne, France Equipment Under Test (EUT): EUT Name: MINO TWIN MINO Model No.: LA113, LA114 ♣ ♣ Please refer to section 4.1 of this report which indicates which model was actually tested and which were electrically identical. Trade mark: LEXON FCC ID: 2ARD3-LA113 Standards: 47 CFR Part 1.1307 47 CFR Part 2.1093 KDB447498D01 General RF Exposure Guidance v06 Date of Receipt: 2018-09-18 Date of Test: 2018-09-19 to 2018-09-26 Date of Issue: 2018-09-27 Test Result : PASS* * In the configuration tested, the EUT complied with the standards specified above. Keny Xu EMC Laboratory Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180900842903 Page: 2 of 6 2 Version Revision Record Version Chapter Date Modifier Remark 01 2018-09-27 Original Authorized for issue by: Leo Li /Project Engineer Eric Fu /Reviewer This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180900842903 Page: 3 of 6 3 Contents Page 1 COVER PAGE .............................................................................................................................................. 1 2 VERSION ...................................................................................................................................................... 2 3 CONTENTS .................................................................................................................................................. 3 4 GENERAL INFORMATION .......................................................................................................................... 4 4.1 GENERAL DESCRIPTION OF EUT ............................................................................................................. 4 4.2 TEST LOCATION...................................................................................................................................... 5 4.3 TEST FACILITY........................................................................................................................................ 5 4.4 DEVIATION FROM STANDARDS ................................................................................................................. 5 4.5 ABNORMALITIES FROM STANDARD CONDITIONS ....................................................................................... 5 4.6 OTHER INFORMATION REQUESTED BY THE CUSTOMER ............................................................................. 5 5 SAR EVALUATION ...................................................................................................................................... 6 5.1 RF EXPOSURE COMPLIANCE REQUIREMENT ............................................................................................ 6 5.1.1 Standard Requirement ..................................................................................................................... 6 5.1.2 Limits ................................................................................................................................................ 6 5.1.3 EUT RF Exposure ............................................................................................................................ 6 This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180900842903 Page: 4 of 6 4 General Information 4.1 General Description of EUT Power supply: Lithium Ion Battery: 3.7V 230mAh rechargeable battery which charged by USB port Cable: USB cable: 30cm unshielded Spectrum Spread Frequency Hopping Spread Spectrum(FHSS) Technology Bluetooth Version: V4.2 single mode Operation Frequency 2402MHz to 2480MHz Modulation Type GFSK, π/4DQPSK Channel Spacing 1MHz Number of Channels 79 Antenna Type PCB Antenna Antenna Gain -0.58dBi Remark: Model No.: LA113, LA114 Only the model LA114 was tested, since the electrical circuit design, layout, components used, internal wiring and functions were identical for the above models, with only difference on model No., package and function TWS. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180900842903 Page: 5 of 6 4.2 Test Location All tests were performed at: SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch No. 1 Workshop, M-10, Middle section, Science & Technology Park, Shenzhen, Guangdong, China 518057 Telephone: +86 (0) 755 2601 2053 Fax: +86 (0) 755 2671 0594 No tests were sub-contracted. 4.3 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L2929) CNAS has accredited SGS-CSTC Standards Technical Services Co., Ltd. Shenzhen Branch EMC Lab to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • A2LA (Certificate No. 3816.01) SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 3816.01. • VCCI The 3m Fully-anechoic chamber for above 1GHz, 10m Semi-anechoic chamber for below 1GHz, Shielded Room for Mains Port Conducted Interference Measurement and Telecommunication Port Conducted Interference Measurement of SGS-CSTC Standards Technical Services Co., Ltd. have been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: G-20026, R-14188, C-12383 and T-11153 respectively. • FCC –Designation Number: CN1178 SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized as an accredited testing laboratory. Designation Number: CN1178. Test Firm Registration Number: 406779. • Innovation, Science and Economic Development Canada SGS-CSTC Standards Technical Services Co., Ltd., Shenzhen EMC Laboratory has been recognized by ISED as an accredited testing laboratory. CAB identifier: CN0006. IC#: 4620C. 4.4 Deviation from Standards None. 4.5 Abnormalities from Standard Conditions None. 4.6 Other Information Requested by the Customer None. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS—CSTC Standards Technical Services Co., Ltd. Shenzhen Branch Report No.: SZEM180300842003 Page sot6 5 SAR Evaluation 5.1 RF Exposure Compliance Requirement 5111. Standard Requirement Accarding to KDB4749D01 General RF Exposure Guidance v06 421. Stendalone SAR test excliion consideratons Unless specifealy required by the pubiched RF exposure KDB procedures, standalone 1—4 head orbody and 10—9 extrmty SAR evaluationfor ganeral papulation exposire condtions,by messurement or numerical simulaten, is not required when the correspanding SAR Excision Threshold condlton, lited below, is satisted 512 Linits The 1—4and 10.4 SAR test excsionthresholds for 100 MHz to 6 GHe at tst separation ditances £30 mm are determined by {(ax. powero channel, ncludingtune:up tolerance, mWi. test separation istance, mmi] [M(GHe] s 3.0for 14 SAR and s 7.5 for 10.4 extemty SAR, where 1(GHe) is the RF channeltransmt fequency in GHe Power and distance are rounded to the nearest mW and mm betore caleulaton‘? The resul s rounded tone decimal placefor comparicon The test exclisions are appleable only when the minimum test separation distance is © 50 mm and fortransmission frequencies betwean 100 MH and 6 GHtz. When the miimum test separation ditance <5 mm, distance of 5 mm is appled to determine SAR test excsion 518 EUVT RF Exposure The Max, poner(rcliing line up ternce)is 019 dbmonthe lavest chanrel 248 GHz( 0.19 dBm bgzithnitems comert o rumerc moutis neaty 1.00 mW Accardng o thefomula esdate ttest exclsio thesholde: GonerREEoure =* «[ To tmesns ce GenerRF Expasir= (103 wl /5 m a /29 it 032 m SAR requrement seso a 05@ Sohe SAR epor i rot equred (0 Mas. poverrelerto Repor No S2ENIErsons«2000 —End ofthe Repor — poporourunoiruucmutretaen


Document Created: 2018-09-29 09:16:51
Document Modified: 2018-09-29 09:16:51
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC