Test Report

FCC ID: 2AR9OAUBDM1801

Test Report

Download: PDF
FCCID_4159604

TEST REPORT CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (1) / (33) Pages Fax: +82-31-624-9501 1. Client ◦ Name : Arnova Corp ◦ Address : 20, Gwangtancheon-ro 51beon-gil, Paju-eup, Paju-si, Gyeonggi-do, Republic of Korea ◦ Date of Receipt : 2018-12-26 2. Manufacturer ◦ Name : Arnova Corp ◦ Address : 20, Gwangtancheon-ro 51beon-gil, Paju-eup, Paju-si, Gyeonggi-do, Republic of Korea 3. Use of Report : For FCC & ISED Certification 4. Test Sample / Model: USPs Button Device Module / AUBDM1801 5. Date of Test : 2019-01-04 to 2019-01-09 6. Test Standard(method) used : FCC 47 CFR part 15 subpart C 15.247, ANSI C63.10-2013, RSS-247 Issue 2 7. Testing Environment: Temp.: (23 ± 1) ℃, Humidity: (48 ± 5) % R.H. 8. Test Results : Compliance The results shown in this test report refer only to the sample(s) tested unless otherwise stated. This Test Report cannot be reproduced, except in full. Technical Manager Affirmation Gwanyong Kim: (Signature) Young-taek Lee: (Signature) 2019-01-29 Republic of KOREA CTK Co., Ltd. CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (2) / (33) Pages Fax: +82-31-624-9501 REPORT REVISION HISTORY Date Revision Page No 2019-01-11 Issued (CTK-2019-00120) all Issued (CTK-2019-00382) 2019-01-29 all Add FCC ID This report shall not be reproduced except in full, without the written approval of CTK Co., Ltd. This document may be altered or revised by CTK Co., Ltd. personnel only, and shall be noted in the revision section of the document. Any alteration of this document not carried out by CTK Co., Ltd. will constitute fraud and shall nullify the document. CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (3) / (33) Pages Fax: +82-31-624-9501 CONTENTS 1. General Product Description ........................................................................................ 4 1.1 Client Information .............................................................................................. 4 1.2 Product Information ............................................................................................ 4 1.3 Peripheral Devices .............................................................................................. 4 2. Facility and Accreditations ........................................................................................... 5 2.1 Test Facility........................................................................................................ 5 2.2 Laboratory Accreditations and Listings .................................................................. 5 2.3 Calibration Details of Equipment Used for Measurement .......................................... 5 3. Test Specifications ..................................................................................................... 6 3.1 Standards.......................................................................................................... 6 3.2 Mode of operation during the test ......................................................................... 7 3.3 Maximum Measurement Uncertainty ..................................................................... 7 4. Technical Characteristic Test ........................................................................................ 8 4.1 6dB Bandwidth ................................................................................................... 8 4.2 Maximum peak Conducted Output Power ............................................................. 12 4.3 Power Spectral Density ..................................................................................... 15 4.4 Band Edge & Conducted Spurious emission .......................................................... 18 4.5 Radiated Emission ............................................................................................ 23 4.6 AC Conducted Emissions ................................................................................... 30 APPENDIX A – Test Equipment Used For Tests ................................................................. 33 CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (4) / (33) Pages Fax: +82-31-624-9501 1. General Product Description 1.1 Client Information Company Arnova Corp 20, Gwangtancheon-ro 51beon-gil, Paju-eup, Paju-si, Gyeonggi-do, Contact Point Republic of Korea Name : Sena Ju Contact Person E-mail : haeyoung.bae@arnova.co.kr Tel : +82-31-952-1907 1.2 Product Information FCC ID 2AR9OAUBDM1801 IC 24666-AUBDM1801 Product Description USPs Button Device Module Model name AUBDM1801 Operating Frequency 2 402 MHz - 2 480 MHz RF Output Power 4.330 dBm (2.71 mW) Antenna type PCB Pattern Antenna Antenna gain -0.62 dBi Number of channels 40 Channel Spacing 2 MHz Type of Modulation GFSK Power Source DC 5 V Test Software(Version) nRFgo Studio (1.21.2.10) RF Power setting in Test SW Initial value Firmware Version Id Number(FVIN) N/A 1.3 Peripheral Devices Device Manufacturer Model No. Serial No. Notebook Computer HP 15-bs563TU CND7253R6P AC/DC Adapter HP HSTNN-LA40 7628207801 CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (5) / (33) Pages Fax: +82-31-624-9501 2. Facility and Accreditations 2.1 Test Facility The measurement facility is located at (Ho-dong), 113, Yejik-ro, Cheoin-gu, Yong-in-si, Gyeonggi-do, Korea. 2.2 Laboratory Accreditations and Listings Registration Country Agency Scope of Accreditation Logo Number FCC Part 15 & 18 USA FCC 805871 EMI (Electromagnetic Interference / Emission) ISED CANADA ISED 8737A-2 EMI (3/10m test site) C-986 VCCI V-3 T-1843 JAPAN VCCI EMI (Electromagnetic Interference / Emission) R-3627 G-387 EMI (Electromagnetic Interference / Emission) KOREA MSIP KR0025 EMS (Electromagnetic Susceptibility / Immunity) 2.3 Calibration Details of Equipment Used for Measurement Test equipment and test accessories are calibrated on regular basis. The maximum time between calibrations is one year or what is recommended by the manufacturer, whichever is less. All test equipment calibrations are traceable to the Korea Research Institute of Standards and Science (KRISS), therefore, all test data recorded in this report is traceable to KRISS. CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (6) / (33) Pages Fax: +82-31-624-9501 3. Test Specifications 3.1 Standards Section in Section in Status Test Requirement(s) FCC RSS (Note 1) Condition 15.247(a) RSS-247 5.2(a) 6 dB Bandwidth C 15.247(e) RSS-247 5.2(b) Transmitter power spectral density C Conducted 15.247(b) RSS-247 5.4(d) Maximum peak conducted output power C 15.247(d) RSS-247 5.5 Unwanted emission C RSS-Gen 15.209 Transmitter emission C Radiated 6.13 Line 15.207(a) RSS-Gen 8.8 AC Conducted Emission C Conducted Note 1: C=Complies NC=Not Complies NT=Not Tested NA=Not Applicable Note 2: The data in this test report are traceable to the national or international standards. Note 3: The sample was tested according to the following specification: FCC Part 15.247, ANSI C63.10-2013, RSS-247 Issue2, RSS-Gen Issue 5 Note 4: The tests were performed according to the method of measurements prescribed in KDB No.558074. CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (7) / (33) Pages Fax: +82-31-624-9501 3.2 Mode of operation during the test The EUT is operated in a manner representative of the typical of the equipments. During at testing, system components were manipulated within the confines of typical usage to maximize each emission. All modulation modes were tests. The results are only attached worst cases. Test Frequency Lowest channel Middle channel Highest channel 2 402 MHz 2 440 MHz 2 480 MHz Test mode Modulation Duty Cycle GFSK 62.18 %(On time : 0.388 ms, Off time : 0.236 ms) 3.3 Maximum Measurement Uncertainty The value of the measurement uncertainty for the measurement of each parameter. Coverage factor k = 2, Confidence levels of 95 % Description Uncertainty Conducted RF Output Power 1.5 dB Power Spectral Density 1.5 dB Occupied Bandwidth 0.1 MHz Unwanted Emission(conducted) 3.0 dB Radiated Emissions (f ≤ 1 GHz) 4.0 dB Radiated Emissions (f > 1 GHz) 5.0 dB CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (8) / (33) Pages Fax: +82-31-624-9501 4. Technical Characteristic Test 4.1 6dB Bandwidth Test Procedures(ANSI C63.10-2013 6.9.2) Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 6 dB relative to the maximum level measured in the fundamental emission. Test Procedures(ANSI C63.10-2013 6.9.3) The occupied bandwidth is the frequency bandwidth such that, below its lower and above its upper frequency limits, the mean powers are each equal to 0.5% of the total mean power of the given emission. Use the 99% power bandwidth function of the instrument and report the measured bandwidth. Test Settings : Center frequency = the highest, middle and the lowest channels a) RBW = 100 kHz b) VBW ≥ 3 x RBW c) Detector = peak d) Trace mode = Max hold e) Sweep = auto couple f) Allow trace to fully stabilize g) Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 6 dB relative to the maximum level measured in the fundamental emission. Limit : 6 dB Bandwidth > 500kHz CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (9) / (33) Pages Fax: +82-31-624-9501 Test Data : Frequency 6 dB Bandwidth 99% Bandwidth Channel Result [MHz] [MHz] [MHz] Low 2 402 0.658 1.049 Middle 2 440 0.666 1.051 Complies High 2 480 0.657 1.058 See next pages for actual measured spectrum plots. CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (10) / (33) Pages Fax: +82-31-624-9501 Low channel (2 402 MHz) Middle channel (2 440 MHz) CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (11) / (33) Pages Fax: +82-31-624-9501 High channel (2 480 MHz) CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (12) / (33) Pages Fax: +82-31-624-9501 4.2 Maximum peak Conducted Output Power Test Procedures(ANSI C63.10-2013 11.9.1) The following procedure can be used when an instrument with a resolution bandwidth that is greater than the DTS bandwidth is available to perform the measurement: Test Settings: Center frequency = the highest, middle and the lowest channels a) RBW ≥ DTS Bandwidth b) VBW ≥ 3 x RBW c) span ≥ 3 x RBW d) Sweep time = auto couple e) Detector = peak f) Trace mode= max hold g) Allow trace to fully stabilize h) Use peak marker function to determine the peak amplitude level. Limit : Maximum Output Power < 1 W (30 dBm) Test Data : Frequency Measurement data Limit Channel Result [MHz] [dBm] [dBm] Low 2 402 4.330 30 Middle 2 440 4.094 30 Complies High 2 480 4.174 30 See next pages for actual measured spectrum plots. CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (13) / (33) Pages Fax: +82-31-624-9501 Low channel (2 402 MHz) Middle channel (2 440 MHz) CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (14) / (33) Pages Fax: +82-31-624-9501 High channel (2 480 MHz) CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (15) / (33) Pages Fax: +82-31-624-9501 4.3 Power Spectral Density Test Procedures(ANSI C63.10-2013 11.10.2) This procedure shall be used if maximum peak conducted output power was used to demonstrate compliance. Test Settings: Center frequency = the highest, middle and the lowest channels a) RBW : 3 kHz ≤ RBW ≤ 100 kHz b) VBW ≥ 3 x RBW c) span ≥ 1.5 x DTS bandwidth d) Sweep time = auto couple e) Detector = peak f) Trace mode= max hold g) Allow trace to fully stabilize h) Use the peak marker function to determine the maximum amplitude level within the RBW. Limit : Power Spectral Density < 8 dBm @ 3 kHz BW Test Data : Frequency Measurement data Limit Channel Result [MHz] [dBm] [dBm] Low 2 402 -11.417 Middle 2 440 -11.291 8 Complies High 2 480 -11.657 See next pages for actual measured spectrum plots. CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (16) / (33) Pages Fax: +82-31-624-9501 Low channel (2 402 MHz) Middle channel (2 440 MHz) CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (17) / (33) Pages Fax: +82-31-624-9501 High channel (2 480 MHz) CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (18) / (33) Pages Fax: +82-31-624-9501 4.4 Band Edge & Conducted Spurious emission Test Procedures(ANSI C63.10-2013 11.11.3) The Unwanted emission from the EUT were measured according to the dictates PKPSD measurement procedure in section 11.11 of ANSI C63.10-2013. In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated device is operating, the RF power that is produced shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided that the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of root-mean-square averaging over a time interval, as permitted under Section 5.4(4), the attenuation required shall be 30 dB instead of 20 dB. Attenuation below the general field strength limits specified in RSS-Gen is not required. Test Settings: Center frequency = the highest, middle and the lowest channels a) RBW = 100 kHz b) VBW ≥ 3 x RBW c) Detector = peak d) Sweep time = auto couple e) Trace mode= max hold f) Allow trace to fully stabilize g) Use the peak marker function to determine the maximum amplitude level. Limit : Emission level < 20 dBc Test results: Complies - All conducted emission in any 100kHz bandwidth outside of the spread spectrum band was at least 20dB lower than the highest in-band spectral density. Therefore the applying equipment meets the requirement. See next pages for actual measured spectrum plots. CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (19) / (33) Pages Fax: +82-31-624-9501 Band–edge CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (20) / (33) Pages Fax: +82-31-624-9501 Conducted Spurious emission Low channel (2 402 MHz) CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (21) / (33) Pages Fax: +82-31-624-9501 Middle channel (2 440 MHz) CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (22) / (33) Pages Fax: +82-31-624-9501 High channel (2 480 MHz) CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (23) / (33) Pages Fax: +82-31-624-9501 4.5 Radiated Emission Test Location 10 m SAC (test distance : 10 m, 3 m) 3 m SAC (test distance : 3 m) Test Procedures 1) In the frequency range of 9 kHz to 30 MHz, magnetic field is measured with Loop Antenna. The center of the Loop Test Antenna is 1m above the ground. During the measurement the Loop Test Antenna rotates about its vertical axis for maximum response at each azimuth about the EUT. 2) In the frequency rage above 30 MHz, Bi-Log Test Antenna(30 MHz to 1 GHz) and Horn Test Antenna(above 1 GHz) are used. Test Antenna is 3m away from the EUT. Test Antenna height is carried from 1m to 4m above the ground to determine the maximum value of the field strength. The emissions levels at both horizontal and vertical polarizations should be tested. Instrument Settings Frequency Range = 9 kHz ~ 25 GHz (2.4 GHz 10th harmonic) a) RBW = 1 MHz for f ≥ 1 GHz, 100 kHz for f < 1 GHz, 9 kHz for f < 30 MHz b) VBW ≥ RBW c) Sweep time = auto couple CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (24) / (33) Pages Fax: +82-31-624-9501 Limit : FCC Part 15 § 15.205 (a) Except as shown in paragraph (d) of this section, only spurious emissions are permitted in any of the frequency bands listed below: Table 1. Restricted Frequency Bands MHz MHz MHz MHz MHz GHz 0.09-0.11 8.37626-8.38675 73-74.6 399.9-410 2690-2900 10.6-12.7 1 0.495-0.505 8.41425-8.41475 74.8-75.2 608-614 3260-3267 13.25-13.4 2.1735-2.1905 12.29-12.293 108-121.94 960-1240 3332-3339 14.47-14.5 4.125-4.128 12.51975-12.52025 123-138 1300-1427 3345.8-3358 15.35-16.2 4.17725-4.17775 12.57675-12.57725 149.9-150.05 1435-1626.5 3600-4400 17.7-21.4 156.52475- 4.20725-4.20775 13.36-13.41 1645.5-1646.5 4500-5150 22.01-23.12 156.52525 6.215-6.218 16.42-16.423 156.7-156.9 1660-1710 5350-5460 23.6-24 6.26775-6.26825 16.69475-16.69525 162.0125-167.17 1718.8-1722.2 7250-7750 31.2-31.8 6.31175-6.31225 16.80425-16.80475 167.72-173.2 2200-2300 8025-8500 36.43-36.5 2 8.291-8.294 25.5-25.67 240-285 2310-2390 9000-9200 Above 38.6 8.362-8.366 37.5-38.25 322-335.4 2483.5-2500 9300-9500 1 Until February 1, 1999, this restricted band shall be 0.490-0.510 MHz. 2 Above 38.6 § 15.205 (b) Except as provided in paragraphs (d) and (e), the field strength of emissions appearing within these frequency bands shall not exceed the limits shown is Section 15.209. At frequencies equal to or less than 1000 MHz, compliance with the limits in Section 15.209 shall be demonstrated using measurement instrumentation employing a CISPR quasi-peak detector. Above 1000 MHz, compliance with the emission limits in Section 15.209 shall be demonstrated based on the average value of the measured emissions. The provisions in Section 15.35 apply to these measurements. CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (25) / (33) Pages Fax: +82-31-624-9501 FCC Part 15 § 15.209 (a) Except as provided elsewhere in this Subpart, the emissions from an intentional radiator shall not exceed the field strength levels specified in the following table : Table 2. General Field Strength Limits for Licence-Exempt Transmitters Field Strength Field Strength Measurement Frequency(MHz) uV/m@3m dBuV/m@3m Distance (meters) 0.009-0.490 2400/F(kHz) - 300 0.490-1.705 24000/F(kHz) - 30 1.705-30 30 - 30 30-88 100** 40 3 88-216 150** 43.5 3 216-960 200** 46 3 Above 960 500 54 3 ** Except as provided in 15.209(g).fundamental emissions from intentional radiators operating under this Section shall not be located in the frequency bands 54-72MHz, 76- 88MHz, 174-216MHz, 470-806MHz. However, operation within these frequency bands is permitted under other sections of this Part, e.g.15.231 and 15.241. Note : 1) For above 1 GHz, the emission limit in this paragraph is based on measurement instrumentation employing an average detector, measurement using instrumentation with a peak detector function, corresponding to 20 dB above the maximum permitted average limit. 2) For above 1 GHz, limit field strength of harmonics : 54 dBuV/m@3m (AV) and 74 dBuV/m@3m (PK) 3) For measurement above 1GHz, the resolution bandwidth is set to 1 MHz and video bandwidth is set to 3 MHz for peak measurement. CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (26) / (33) Pages Fax: +82-31-624-9501 Test Setup: 1) For field strength of emissions from 9 kHz to 30 MHz 2) For field strength of emissions from 30 MHz to 1 GHz CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (27) / (33) Pages Fax: +82-31-624-9501 3) For field strength of emissions above 1 GHz Test results 1) 9 kHz to 30 MHz The requirements are: Complies Frequency Measured Data Margin Remark (MHz) (dBuV/m) (dB) - - - See note Note : The amplitude of spurious emissions that are attenuated by more than 20 dB below the permissible value has no need to be reported. Distance extrapolation factor = 40 log (specific distance / test distance) (dB) CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (28) / (33) Pages Fax: +82-31-624-9501 2) 30 MHz to 1 GHz Test mode : Low Channel(Worst case) The requirements are: Complies Test Data Remark : 1. The Unwanted emission was measured in the following position: EUT stand-up position(Z axis), lie-down position(X,Y axis). The worst emission was found in stand-up position(Z axis) and the worst case was recorded. 2. Result = Reading + c.f(Correction factor) 3. Correction factor = Antenna factor + Cable loss + 6 dB attenuator - Amp Gain 4. This data is the Peak(PK) value. CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (29) / (33) Pages Fax: +82-31-624-9501 3) 1 GHz to 25 GHz The requirements are: Complies Test Data Ant. Frequency Reading c.f Result Limit Margin Channel Pol. Remark [MHz] [dBuV/m] [dB/m] [dBuV/m] [dBuV/m] [dB] (V/H) 7 206.69 V 48.00 6 54.00 74 20.00 Peak Low 7 206.69 H 34.30 6 40.30 54 13.70 Average 7 321.17 V 49.60 6 55.60 74 18.40 Peak Middle 7 319.26 H 33.60 6 39.60 54 14.40 Average 7 439.47 V 46.50 6 52.50 74 21.50 Peak High 7 439.47 V 32.20 6 38.20 54 15.80 Average Remarks 1. The Unwanted emission was measured in the following position: EUT stand-up position(Z axis), lie-down position(X,Y axis). The worst emission was found in stand-up position(Z axis) and the worst case was recorded. 2. Result = Reading + c.f(correction factor) 3. Correction factor = Antenna factor + Cable loss - Amp Gain CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (30) / (33) Pages Fax: +82-31-624-9501 4.6 AC Conducted Emissions A radio apparatus that is designed to be connected to the public utility (AC) power line shall ensure that the radio frequency voltage, which is conducted back onto the AC power line on any frequency or frequencies within the band 150 kHz-30 MHz, shall not exceed the limits. Instrument Settings IF Band Width: 9 kHz Test Procedures The EUT was placed on a non-metallic table 0.8m above the metallic, grounded floor and 0.4m from the reference ground plane wall. The distance to other metallic surfaces was at least 0.8m. Amplitude measurements were performed with a quasi-peak detector and an average detector. Limit Frequency Conducted Limit (dBuV) (MHz) Quasi-peak Average** 0.15 ~ 0.5 66 to 56* 56 to 46* 0.5 ~ 5 56 46 5 ~ 30 60 50 * The level decreases linearly with the logarithm of the frequency. ** A linear average detector is required. Test Results The requirements are: Complies CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (31) / (33) Pages Fax: +82-31-624-9501 Test Data [LINE] CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (32) / (33) Pages Fax: +82-31-624-9501 [NEUTRAL] CTK-D151-06 R101 Rev.0

CTK Co., Ltd. (Ho-dong), 113, Yejik-ro, Cheoin-gu, Report No.: Yongin-si, Gyeonggi-do, Korea CTK-2019-00382 Tel: +82-31-339-9970 Page (33) / (33) Pages Fax: +82-31-624-9501 APPENDIX A – Test Equipment Used For Tests Name of Equipment Manufacturer Model No. Serial No. Cal Date Due Date 1 Signal Analyzer Rohde & Schwarz FSV40 101574 2018-03-09 2019-03-09 2 Signal Generator Rohde & Schwarz SMB100A 175528 2018-10-24 2019-10-24 3 EMI Test Receiver Rohde & Schwarz ESCI7 100814 2018-10-25 2019-10-25 4 Bilog Antenna Schaffner CBL6111C 2551 2018-05-10 2020-05-10 5 Active Loop Antenna SCHWARZBECK FMZB 1513 1513-125 2018-05-02 2020-05-02 6 6dB Attenuator Rohde & Schwarz DNF 272.4110.50-2 2018-10-25 2019-10-25 7 AMPLIFIER SONOMA 310 291721 2018-02-02 2019-02-02 8 Preamplifier Agilent 8449B 3008A02011 2018-12-03 2019-12-03 9 EMI Test Receiver Rohde & Schwarz ESU40 100336 2018-02-01 2019-02-01 10 Preamplifier Agilent 8449B 3008A02011 2018-12-03 2019-12-03 11 Horn Antenna ETS-Lindgren 3117 00154525 2017-09-14 2019-09-14 12 Horn Antenna ETS-Lindgren 3116 0062916 2017-04-25 2019-04-25 13 Signal Analyzer Agilent N9020A MY50510324 2018-01-26 2019-01-26 14 Band Reject Filter Micro Tronics BRM50702 G233 2018-01-26 2019-01-26 Cable Manufacturer Model No. Serial No. Check Date 1 RF Cable (Radiated) HUBER+SUHNER SUCOFLEX 104 MY27558/4 2018-12-19 N/A 2 RF Cable (Radiated) HUBER+SUHNER SUCOFLEX 104 2018-12-19 (below 1GHz) 3 RF Cable (Radiated) HUBER+SUHNER SUCOFLEX 104 MY27573/4 2018-12-19 N/A 4 RF Cable (Radiated) HUBER+SUHNER SUCOFLEX 106 2018-12-19 (above 1GHz) 5 RF Cable (Radiated) HUBER+SUHNER SUCOFLEX 102 MY2374/2 2018-12-19 6 RF Cable (Radiated) HUBER+SUHNER SUCOFLEX 102 MY4728/2 2018-12-19 CTK-D151-06 R101 Rev.0


Document Created: 2019-01-29 23:58:42
Document Modified: 2019-01-29 23:58:42
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC