Module request letter

FCC ID: 2AR3A-ITM-S-B

Cover Letter(s)

Download: PDF
FCCID_4132251

Applicant/Grantee Samsung Electronics Co Ltd / 2AR3A FCC ID: 2AR3A-ITM-S-B Modular Transmitters Request for Modular Approval Request for Limited Modular Approval Requirements EUT Conditions Comply (Y/N) Single Modular Approval Requirements 1 The radio elements of the modular transmitter The radio portion of this Y must have their own shielding. The physical module has been shielded by crystal and tuning capacitors may be located shieldcan. external to the shielded radio elements. 2 The modular transmitter must have buffered This module has Y modulation/data inputs (if such inputs are TLSR8269F512, Bluetooth LE provided) to ensure that the module will comply standard SoC that controls with modular approval requirements under transmitters integrated in the conditions of excessive data rates or over- chip. The SoC chipset’s embedded modulation. 512kB flash addresses the buffering. 3 The modular transmitter must have its own power The TLSR8269F512’s Y supply regulation. embedded LDO enables its own power supply regulation 4 The modular transmitter must comply with the This module is equipped with a Y antenna and transmission system requirements. PCB pattern antenna. For further details please refer to the antenna data sheet included in the filing. 5 The modular transmitter must be tested in a stand- This module was tested in a Y alone configuration, i.e., the module must not be stand-alone configuration. inside another device during testing. Unless the transmitter module will be battery powered, it must comply with the AC line conducted requirements found in Section 15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see Section 15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see Section 15.31(i)). 6 The modular transmitter must be equipped with This module is labeled with its Y either a permanently affixed label or must be own FCC ID number, Please capable of electronically displaying its FCC see product label design and identification number. the external photograph of the (A) If using a permanently affixed label, the modular device with this label submitted transmitter must be labeled with its own FCC identification with the application number, and, if the FCC identification number is not visible when the module is installed inside another device, then the

outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains Transmitter Module FCC ID: XYZMODEL1” or “Contains FCC ID: XYZMODEL1.” Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. (B) If the modular transmitter uses an electronic display of the FCC identification number, the information must be readily accessible and visible on the modular transmitter or on the device in which it is installed. If the module is installed inside another device, then the outside of the device into which the module is installed must display a label referring to the enclosed module. This exterior label can use wording such as the following: “Contains FCC certified transmitter module(s).” Any similar wording that expresses the same meaning may be used. The user manual must include instructions on how to access the electronic display. A copy of these instructions must be included in the application for equipment authorization. 7 The modular transmitter must comply with any This module is compliant with Y specific rules or operating requirements that all applicable FCC rules. Detail ordinarily apply to a complete transmitter and the instructions for maintaining manufacturer must provide adequate instructions compliance are given in the along with the module to explain any such Users Manual. requirements. A copy of these instructions must be included in the application for equipment authorization. 8 The modular transmitter must comply with any This module is compliant with Y applicable RF exposure requirements in its final all applicable RF exposure configuration. requirements. RF Exposure is addressed in the test report. A limited modular approval may be granted for single or split modular transmitters that do not comply with all of the above requirements, e.g., shielding, minimum signaling amplitude, buffered modulation/data inputs, or power supply regulation, if the manufacturer can demonstrate by alternative means in the application for equipment authorization that the modular transmitter meets all the applicable Limited modular approval also may be granted in those instances where compliance with RF exposure rules is demonstrated only for particular product configurations. The applicant for certification must state how control of the end product into which the module will be installed will be maintained such that full compliance of the end product is always ensured. Name and Title of the Applicant: JANG MOUNGJIN / Staff Engineer Date: 2018-12-20 Signature:


Document Created: 2019-01-10 13:17:32
Document Modified: 2019-01-10 13:17:32
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC