User Manual

FCC ID: 2AR2STAPN505

Users Manual

Download: PDF
FCCID_4400047

TAPN505 User manual Register your product and get support at www.philips.com/support

Contents 1 Important safety instructions 2 Hearing Safety 2 General information 2 2 Your Bluetooth in-ear headphones 3 What's in the box 3 Other devices 3 Overview of your Bluetooth wireless headset 3 3 Get started 5 Charge the battery 5 Pair the headphones with your mobile phone 5 4 Use your headphones 6 Connect the headphones to a Bluetooth device 6 Manage your calls and music 6 5 Technical data 8 6 Notice 9 Declaration of conformity 9 Disposal of your old product and battery 9 Compliance with EMF 10 Environmental information 10 Notice of compliance 10 7 Frequently asked questions 11

1 Important General information safety To avoid damage or malfunction: instructions Caution  Do not expose headphones to excessive heat  Do not drop your headphones. Hearing Safety  Headphones shall not be exposed to dripping or splashing.  Do not allow your headphones to be submerged in water.  Do not use any cleaning agents containing alcohol, ammonia, benzene, or abrasives.  If cleaning is required use a soft doth, if necessary dampened with a minimum amount of water or diluted mild soap, to clean the Danger product.  The integrated battery shall not be exposed to  To avoid hearing damage, limit the time you excessive heat such as sunshine, fire or the use headphones at high volume and set the like. volume to a safe level. The louder the  Danger of explosion if battery is incorrectly volume, the shorter the safe listening time is. replaced. Replace only with the same or equivalent type. Be sure to observe the following guide- lines when using your headset. About operating and storage • Listen at reasonable volumes for temperatures and humidity reasonable periods of time. • Operate or store in a place where • Be careful not to adjust the volume temperature is between -15°C (5°F) continuously upwards as your and 55°C (131 °F) (up to 90% hearing adapts. relative humidity. • Do not turn up the volume so high • Battery life may be shorter in high that you can't hear what's around or low temperature conditions. you. • You should use caution or tempo- rarily discontinue use in potentially hazardous situations. • Excessive sound pressure from earphones and headphones can cause hearing loss. • Using headphones with both ears covered while driving is not recom- mended and may be illegal in some areas while driving. • For your safety, avoid distractions from music or phone calls while in traffic or other potentially dangerous environments.

2 Your Bluetooth in-ear headphones Audio cable with USB plug Congratulations on your purchase, and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome. With this Philips in-ear headphones, Quick start guide you can: • enjoy convenient wireless handsfree calls; • enjoy and control wireless music; Other devices • switch between calls and music. A mobile phone or device (e.g. note- book, PDA, Bluetooth adapters, MP3 players etc) which supports Bluetooth What's in the box and is compatible to the headset (see 'Technical data' on page 10). Philips Bluetooth in-ear headphones Philips TAPN505 Replaceable rubber ear caps x 2 pairs USB charging cable (for charging only)

Overview of your Bluetooth wireless headset  Microphone  LED indicator  ANC On/Off/Abint sound  Volume/Track control button  Power On/Off Micro USB charging slot

3 Get started Pair the headphones with your mobile phone Before you use the headphones with your mobile phone for the first time, pair Charge the battery it with a mobile phone. A successful pairing establishes a unique encrypted Note link between the headphones and mobile phone. The headphones store  Before you use your headset for the first time, the last 8 devices in the memory. If you place the headsets in the charging case and charge the battery for 3 hours for optimum try to pair more than 8 devices, the battery capacity and lifetime. earliest paired device is replaced by the  Use only the original USB charging cable to new one. avoid any damage.  Finish your call before charging the headset, Make sure that the headphones are as connecting the headset for charging will power the headset off. fully charged and turned off. Press and hold for 6 seconds Charging case until the blue and white LED flashes alternately. Connect the supplied USB charging cable to: • The micro USB charging slot on the headphones and; • The charger/USB port of a computer. LED turns white during charging and turns off when the headphones in fully charged. Tip  Normally, a full charge takes 2 hours. Philips TAPN505

4 Use your Manage your calls and headset music On/off Connect the headset to Task Button Operation your Bluetooth device Turn the On/off, Press and hold head- music/call for 3 seconds. Turn on your mobile phone/ phones on. control Bluetooth device. Turn the On/off, Press and hold Press and hold the on/off button to head- music/call for 5 seconds. turn the headphones on. phones off. control The red The blue LED flashes. LED is on and The headphones are recon- fades nected to the last connected out. mobile phone/ Bluetooth device automatically. If the last one is not available, the Music control headphones try to reconnect to the second last connected Task Button Operation device. Play or On/off, Press once. pause music. music/call control Tip Adjust volume. Press once.  If you turn on the mobile phone/Bluetooth Next track. Long press. device or activate the Bluetooth feature Previous track. Long press. after turning on the headphones, you have to reconnect the headphones and mobile phone/Bluetooth device manually. Call control Task Button Operation Pick up/ On/off, Press once. hang up a music/ 1 beep. Note call. call control  If the headphones fail to connect to any Switch On/off, Press twice. Bluetooth device within range in 5 minutes, caller music/- 1 beep. it will switch off automatically to save the battery life. during a call call. control

Other headphones indicator status Headphones status Indicator The headphones The blue LED are connected flashes for every to a Bluetooth 8 seconds. device, while the headphones in standby mode or while you are listening to music. The headphones The LED flashes are ready for blue and red pairing. alternately. The headphones The blue LED are on but not flashes quickly connected to a If no connection Bluetooth device. can be made, the headphones will turn itself off within 5 minutes. Low battery level. The white LED flashes 3 times for every 150 seconds until it is out of power Battery is fully Red LED is off. charged.

5 Technical data Headset Music time: 7 hours Talk time: 7 hours Standby time: 160 hours Charging time: 2 hours Rechargeable lithium polymer battery (120 mAh) Bluetooth version: 5.0 Compatible Bluetooth profiles: • HSP (Hands-Free Profile-HFP) • A2DP (Advanced Audio Distri- bution Profile) • AVRCP (Audio Video Remote Control Profile) Supported audio codec: SBC Frequency range: 2.402-2.480 GHz Transmitter power: < 20 dBm Operating range: Up to 10 meters (33 feet) Digital echo & noise reduction Auto power off Note  Specifications are subject to change without notice.

6 Notice Remove the integrated battery If there is no collection/recycling system for electronic products in your country, Declaration of conformity you can protect the environment by Hereby, MMD Hong Kong Holding Limited removing and recycling the battery declares that this product is in compli- before disposing the headphones. ance with the essential requirements and • Make sure the headset is discon- other relevant provisions of Directive nected from the charging case 2014/53/EU. You can find the Declaration before removing the battery. of Conformity on www.p4c.philips.com. Disposal of your old product and battery Your product is designed and manufac- tured with high quality materials and components, which can be recycled and reused. This symbol on a product means that the product is covered by European Directive 2012/19/EU. This symbol means that the product contains a built-in rechargeable battery covered by European Directive 2013/56/EU which cannot be disposed of with normal household waste. We strongly advise you to take your product to an official collection point or a Philips service centre to have a professional remove the rechargeable battery. Inform yourself about the local separate collection system for electrical and electronic products and rechargeable batteries. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environ- ment and human health.

However, there is no guarantee that Compliance with EMF interference will not occur in a particular installation. If this equipment does This product complies with all applica- cause harmful interference to radio or ble standards and regulations regarding television reception, which can be exposure to electromagnetic fields. determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more Environmental information of the following measures: All unnecessary packaging has been Relocate the receiving antenna. omitted. We have tried to make the Increase the separation between packaging easy to separate into three equipment and receiver materials: cardboard (box), polystyrene Connect the equipment into an outlet foam (buffer) and polyethylene (bags, on a circuit different from that to which protective foam sheet.) the receiver is connected. Your system consists of materials which Consult the dealer or an experienced can be recycled and reused if disassem- radio/TV technician for help. bled by a specialized company. Please FCC Radiation Exposure Statement: observe the local regulations regarding This equipment complies with FCC the disposal of packaging materials, radiation exposure limits set forth for an exhausted batteries and old equipment. uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any Notice of compliance other antenna or transmitter. The device complies with the FCC rules, Canada: Part 15. Operation is subject to the This device complies with Industry following two conditions: Canada licence-exempt RSS stan- 1. This device may not cause harmful dard(s). Operation is subject to the interference, and following Two conditions: (1) this device 2. This device must accept any may not cause harmful interference, and interference received, including (2) this device must accept any interfer- interference that may cause ence received, including interference undesired operation. that may cause undesired operation. CAN ICES-3(B)/NMB-3(B) FCC rules IC Radiation Exposure Statement: This equipment has been tested and This equipment complies with Canada found to comply with the limits for a radiation exposure limits set forth for Class B digital device, pursuant to part uncontrolled environments. 15 of the FCC Rules. These limits are This transmitter must not be co-located designed to provide reasonable protec- or operating in conjunction with any tion against harmful interference in a other antenna or transmitter residential installation. This equipment generates, uses and can radiate radio Caution: The user is cautioned that frequency energy and, if not installed changes or modifications not expressly and used in accordance with the approved by the party responsible for instruction manual, may cause harmful compliance could void the user's interference to radio communications. authority to operate the equipment.

7 Frequently The Bluetooth device cannot find the headset. asked • The headset may be connected to a previously paired device. Turn off the questions connected device or move it out of range. • Pairing may have been reset or the headset has been previously paired My Bluetooth headset does not turn on. with another device. Pair the headset The battery level is low. Charge the with the Bluetoot device again as headset. described in the user manual. (see ‘Pair the headset with your Bluetooth I cannot pair my Bluetooth headset with device at the fist time’ on page 6). my Bluetooth device. The Bluetooth is disabled. Enable the My Bluetooth headset is connected to a Bluetooth feature on your Bluetooth Bluetooth stereo enabled mobile phone, device and turn on the Bluetooth device but music only plays on the mobile phone before you turn on the headset. speaker. Refer to the user manual of your mobile Pairing does not work. phone. Select to listen to music through • Put both earpieces into charging case. the headset. • Make sure you have disabled the Bluetooth function of any previously The audio quality is poor and crackling connected Bluetooth devices. noise can be heard. • On your Bluetooth device, delete • The Bluetooth device is out of range. “Philips SHB2505” from the Bluetooth Reduce the distance between your list. headset and Bluetooth device, or • Pair your headset (see ‘Pair the remove obstacles between them. headset with your Bluetooth device • Charge your headset. at the first time’ on page 6). The audio quality is poor when streaming How to reset pairing. from the mobile phone is very slow, or Take both headsets out of the charging audio streaming does not work at all. case. Press twice on both headsets Make sure your mobile phone not only Multi-function buttons until the LED supports (mono) HSP/HFP but alos indicator turns white, wait for about 10 supports A2DP and is BT4.0x (or higher) seconds. You will hear “Connected”, “Left compatible (see ‘Technical data’ on page Channel”, “Right Channel”, as pairing 10). successful.

I hear but cannot control music on my • The right and left earpieces are Bluetooth device (e.g. play/pause/skip disconnected from each other, forward/backward). Turn off both earpiece first. Then Make sure the Bluetooth audio source put both earpieces back to supports AVRCP (see ‘Technical data’ on charging case for 5 seconds and page 10). take them out. This will turn the earpieces on and connect the two The volume level of the headset is toot earpieces. Reconnect the headset low. to your Bluetooth device. Some Bluetooth devices cannot link the volume level with the headset through • The headset is connected to more volume sync. In this case, you have to than one Bluetooth device. Switch adjust the volume on your Bluetooth off the Bluetooth function of all device independently to achieve an connected devices. Turn off both appropriate volume level. earpieces. Put both earpieces back to charging case for 5 seconds I cannot connect the headset to another and take them out. Reconnect the device, what do I do? headset to your Bluetooth device. • make sure the Bluetooth function of Note that the headset is desighed the previous paired device is turned for connecting to only one Blue off. tooth device ath a time. When you • Repeat the pairing procedure on your reconnect the headset to your second device (see ‘Pair the headset Bluetooth device, make sure the with your Bluetooth device at the Bluetooth function of any other first time’ on page 6). Previously paired/connected devices are off. I hear sound from only one earpiece. • If you are in a call, it is normal that • If the above solutions do not help, sound comes from the right and left factory reset the headset (see earpiece. ‘Factory reset the headset’ on • If you are listening to music but sound page 9). only comes from one earpiece: • The other earpiece may be out of For further support, visit battery. For optimal performance, www.philips.com/support. charge both earpiece fully.

Este equipamento não tem direito à proteção contra interferência prejudicial e não pode causar interferência em sistemas devidamente autorizados. Este produto está homologado pela ANATEL, de acordo com os procedimentos regulamentados pela Resolução 242/2000, e atende aos requisitos técnicas aplicados. Para maiores informações, consulte a site da ANATEL: www.anatel.gov.br Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V. and are used under license. This product has been manufactured by and is sold under the responsibility of MMD Hong Kong Holding Limited or one of its affiliates, and MMD Hong Kong Holding Limited is the warrantor in relation to this product. UM_TAPN402_00_EN_V0.1


Document Created: 2019-06-03 15:56:30
Document Modified: 2019-06-03 15:56:30
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC