FCC_Test_Report

FCC ID: 2AR2DPRO-S

Test Report

Download: PDF
FCCID_4108214

                        Page 1 of 24           Report No.: UNIA2018112916FR-01




      FCC RADIO TEST REPORT

                FCC ID: 2AR2DPRO-S


               Product: WAKE UP WINE
           Trade Name: N/A
           Model Name: PRO-S
           Serial Model: Pro
             Report No.: UNIA2018112916FR-01



                         Prepared for

              WiSIC Electronic Technology Co., Ltd.
No. A48 GaoYu South Road, PingShan Industry Area, Tangxia Town,
                       Dongguan , China



                         Prepared by

          Shenzhen United Testing Technology Co., Ltd.

2F, Annex Bldg, Jiahuangyuan Tech Park, #365 Baotian 1 Rd, Tiegang
     Community, Xixiang Str, Bao'an District, Shenzhen, China


                                                             Page 2 of 24              Report No.: UNIA2018112916FR-01

                                           TEST RESULTCERTIFICATION

Applicant’s name.................... : WiSIC Electronic Technology Co., Ltd.
                                                  No. A48 GaoYu South Road, PingShan Industry Area, Tangxia
Address...................................... :
                                                  Town, Dongguan , China
Manufacture's Name.............. : WiSIC ElectronicTechnology Co., Ltd.
                                                  No.A48 GaoYu South Road, PingShan Industry Area,Tangxia
Address...................................... :
                                                  Town, Dongguan City, Guangdong ,China
Product description
Product name............................... : WAKE UP WINE
Trade Mark.................................: N/A
Model and/or type reference . : PRO-S, Pro
                                                  FCC Rules and Regulations Part 15 Subpart C Section 15.249,
Standards..................................:
                                                  ANSI C63.10: 2013
This device described above has been tested by Shenzhen United Testing Technology
Co., Ltd., and the test results show that the equipment under test (EUT) is in compliance
with the FCC requirements. And it is applicable only to the tested sample identified in the
report.
This report shall not be reproduced except in full, without the written approval of UNI, this
document may be altered or revised by Shenzhen United Testing Technology Co., Ltd.,
personnel only, and shall be noted in the revision of the document.

Date of Test............................................... :
Date (s) of performance of tests...............:                  Nov. 30, 2018 ~ Dec. 07, 2018
Date of Issue.............................................. :      Dec. 07, 2018
Test Result.................................................. :   Pass




Prepared by:
                                                                            Kahn yang/Editor

Reviewer:
                                                                         Sherwin Qian/Supervisor

Approved & Authorized Signer:
                                                                              Liuze/Manager




                                                    Table of Contents                                     Page


                                Page 3 of 24   Report No.: UNIA2018112916FR-01


                           Table of Contents                      Page


1 . TEST SUMMARY                                                         4
2 . GENERAL INFORMATION                                                  5
  2.1 GENERAL DESCRIPTION OF EUT                                         5
  2.2 Carrier Frequency of Channels                                      6
  2.3 Operation of EUT during testing                                    6
  2.4DESCRIPTION OF TEST SETUP                                           6
  2.5MEASUREMENT INSTRUMENTS LIST                                        7
3 . CONDUCTED EMISSIONS TEST                                             8
  3.1 Conducted Power Line Emission Limit                                8
  3.2 Test Setup                                                         8
  3.3 Test Procedure                                                     8
  3.4 Test Result                                                        8
4 RADIATED EMISSION TEST                                             11
  4.1 Radiation Limit                                                 11
  4.2 Test Setup                                                      11
  4.3 Test Procedure                                                  12
  4.4 Test Result                                                     12
5 BAND EDGE                                                          18
  5.1 Limits                                                          18
  5.2 Test Procedure                                                  18
  5.3 Test Result                                                     18
6 OCCUPIED BANDWIDTH MEASUREMENT                                     20
  6.1 Test Setup                                                      20
  6.2 Test Procedure                                                  20
  6.3 Measurement Equipment Used                                      20
  6.4 Test Result                                                     20
7 ANTENNA REQUIREMENT                                                22
8 PHOTOGRAPH OF TEST                                                 23
  8.1 Radiated Emission                                               23
  8.2Conducted Emission                                               24


                                         Page 4 of 24                Report No.: UNIA2018112916FR-01


. TEST SUMMARY

TEST PROCEDURES AND RESULTS

  DESCRIPTION OF TEST                                                 RESULT
  CONDUCTED EMISSIONS TEST                                           COMPLIANT
  RADIATED EMISSION TEST                                             COMPLIANT
  BAND EDGE                                                          COMPLIANT
  OCCUPIED BANDWIDTH MEASUREMENT                                     COMPLIANT
  ANTENNA REQUIREMENT                                                COMPLIANT


 TEST FACILITY


  Test Firm          :   Shenzhen United Testing Technology Co.,Ltd.

  Address            :2F, Annex Bldg, JiahuangyuanTech Park, #365 Baotian 1
                         Rd,TiegangCommunity, XixiangStr, Bao'an District, Shenzhen,China
   The testing quality ability of our laboratory meet with "Quality Law of People's Republic of
   China" Clause 19.The testing quality system of our laboratory meets with ISO/IEC-17025
   requirements, which is approved by CNAS. This approval result is accepted by MRA of
   APLAC.
   Our test facility is recognized, certified, or accredited by the following organizations:
   CNAS-LAB Code: L6494
   The EMC Laboratory has been assessed and in compliance with CNAS-CL01 accreditation
   criteria for testing Laboratories (identical to ISO/IEC 17025:2017 General Requirements) for
   the Competence of testing Laboratories.
   Designation Number: CN1227
   Test Firm Registration Number: 674885
  The EMC Laboratory has been registered and fully described in a report filed with the (FCC)
  Federal Communications commission. The acceptance letter from the FCC is maintained in
  our files.



 MEASUREMENT UNCERTAINTY

  Measurement Uncertainty
  Conducted Emission Expanded Uncertainty                            =   2.23dB, k=2
  Radiated emission expanded uncertainty(9kHz-30MHz)                 =   3.08dB, k=2
  Radiated emission expanded uncertainty(30MHz-1000MHz)              =   4.42dB, k=2
  Radiated emission expanded uncertainty(Above 1GHz)                 =   4.06dB, k=2


                                Page 5 of 24                Report No.: UNIA2018112916FR-01


. GENERAL INFORMATION

GENERAL DESCRIPTION OF EUT

     Equipment               WAKE UP WINE
     Trade Mark              N/A
     Model Name              PRO-S
     Serial No.              Pro
                             All model’s the function, software and electric circuit are
     Model Difference        the same, only with a product color and model named
                             different. Test sample model: PRO-S.
     FCC ID                  2AR2DPRO-S
     Antenna Type            PCB Antenna
     Antenna Gain            1dBi
     Frequency Range         2402~2480MHz
     Number of Channels      40CH
     Modulation Type         GFSK
     Battery                 DC 7.4V, 2500mAh
     PowerSource             DC 12V from adapter withAC 120(240)V/60Hz
                             M/N: M120080E111
     Adapter Model           Input: AC 100-240V, 50/60Hz, 0.35A
                             Output: DC 12V, 0.8A


                                       Page 6 of 24                Report No.: UNIA2018112916FR-01


Carrier Frequency of Channels

                                          Channel List
          Frequency                 Frequency                    Frequency              Frequency
Channel                 Channel                    Channel                   Channel
            (MHz)                     (MHz)                       (MHz)                   (MHz)
  01         2402          11          2422             21         2442         31            2462
  02         2404          12          2424             22         2444         32            2464
  03         2406          13          2426             23         2446         33            2466
  04         2408          14          2428             24         2448         34            2468
  05         2410          15          2430             25         2450         35            2470
  06         2412          16          2432             26         2452         36            2472
  07         2414          17          2434             27         2454         37            2474
  08         2416          18          2436             28         2456         38            2476
  09         2418          19          2438             29         2458         39            2478
  10         2420          20          2440             30         2460         40            2480

Operation of EUT during testing

    Operating Mode
    The mode is used: Transmitting mode
                        Low Channel: 2402MHz
                        Middle Channel: 2440MHz
                        High Channel: 2480MHz

DESCRIPTION OF TEST SETUP

    Operation of EUT during Conducted testing:


             AC Power                    Adapter                     EUT


    Operation of EUT duringRadiation testing:


                                           EUT


    Table forauxiliary equipment:

       Equipment Description      Manufacturer           Model         Calibration Due Date
             Adapter               QiangHan           M120080E111              N/A


                                           Page 7 of 24             Report No.: UNIA2018112916FR-01


MEASUREMENT INSTRUMENTS LIST

Item       Equipment           Manufacturer           Model No.        Serial No.    Calibrated until
                                  CONDUCTED EMISSIONS TEST
 1            AMN              Schwarzbeck            NNLK8121         8121370          2019.9.9
 2            AMN                  ETS                    3810/2       00020199         2019.9.9
           EMI TEST
 3                            Rohde&Schwarz                ESCI         101210          2019.9.9
           RECEIVER
 4            AAN                TESEQ                    T8-Cat6        38888          2019.9.9
                                    RADIATED EMISSION TEST
 1        Horn Antenna            Sunol                   DRH-118      A101415         2019.9.29
 2     BicoNILog Antenna          Sunol              JB1 Antenna       A090215         2019.9.29
 3          PREAMP                 HP                      8449B      3008A00160        2019.9.9
 4          PREAMP                 HP                      8447D      2944A07999        2019.9.9
           EMI TEST
 5                            Rohde&Schwarz                ESR3         101891          2019.9.9
           RECEIVER
         VECTOR Signal
 6                            Rohde&Schwarz           SMU200A           101521         2019.9.28
           Generator
 7       Signal Generator        Agilent                  E4421B      MY4335105        2019.9.28
 8     MXA Signal Analyzer       Agilent                  N9020A     MY50510140        2019.9.28
 9     MXA Signal Analyzer       Agilent                  N9020A     MY51110104         2019.9.9
        ANT Tower&Turn
 10                             Champro                   EM 1000        60764         2019.9.28
         table Controller
 11     Anechoic Chamber       Taihe Maorui           9m*6m*6m         966A0001         2019.9.9
 12      Shielding Room        Taihe Maorui          6.4m*4m*3m        643A0001         2019.9.9
 13     RF Power sensor           DARE               RPR3006W       15I00041SNO88      2019.3.14
 14     RF Power sensor           DARE               RPR3006W       15I00041SNO89      2019.3.14
 15      RF power divider        Anritsu                  K241B         992289         2019.9.28
         Wideband radio
 16                           Rohde&Schwarz               CMW500        154987         2019.9.28
       communication tester
 17     Biconical antenna      Schwarzbeck            VHA 9103         91032360         2019.9.8
 18     Biconical antenna      Schwarzbeck            VHA 9103         91032361         2019.9.8
        Broadband Hybrid
 19                            Schwarzbeck            VULB9163      VULB9163#958        2019.9.8
            Antennas
 20       Horn Antenna         Schwarzbeck           BBHA9120D        9120D-1680       2019.1.12
       Active Receive Loop
 21                            Schwarzbeck           FMZB 1919B          00023        2018.11.02
             Antenna
 22       Horn Antenna         Schwarzbeck           BBHA 9170       BBHA9170651      2019.03.14
           Microwave
 23        Broadband           Schwarzbeck            BBV 9721          100472        2018.10.24
           Preamplifier
 24    Active Loop Antenna     Com-Power                  AL-130R      10160009       2019.05.10
 25        Power Meter          KEYSIGHT                  N1911A     MY50520168       2019.05.10
 26      Frequency Meter         VICTOR                   VC2000      997406086       2019.05.10
 27     DC Power Source         HYELEC                HY5020E         055161818       2019.05.10


                                         Page 8 of 24                 Report No.: UNIA2018112916FR-01


. CONDUCTED EMISSIONS TEST

3.1 Conducted Power Line Emission Limit
For unintentional device, according to § 15.107(a) Line Conducted Emission Limits is as following

                                            Maximum RF Line Voltage(dBV)
        Frequency
                                     CLASS A                                CLASS B
          (MHz)
                              Q.P.               Ave.               Q.P.                Ave.
        0.15~0.50              79                 66               66~56*             56~46*
        0.50~5.00              73                 60                 56                  46
        5.00~30.0              73                 60                 60                  50

   * Decreasing linearly with the logarithm of the frequency
   For intentional device, according to §15.207(a) Line Conducted Emission Limit is same as above table.

3.2 Test Setup




3.3 Test Procedure
 1,The equipment was set up as per the test configuration to simulate typical actual usage per the
    user’smanual. The EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and is
    placed onthe ground plane as per ANSI C63.10.
 2, Support equipment, if needed, was placed as per ANSI C63.10.
 3, All I/O cables were positioned to simulate typical actual usage as per ANSI C63.10.
 4,If a EUT received DC power from the USB Port of Notebook PC, the PC’s adapter received
    AC120V/60Hzpower through a Line Impedance Stabilization Network (LISN) which supplied power
    source and wasgrounded to the ground plane.
 5, All support equipments received AC power from a second LISN, if any.
 6, The EUT test program was started. Emissions were measured on each current carrying line of the
    EUTusing a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has
    twomonitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line
    1connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line
    1connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver.
 7, Analyzer / Receiver scanned from 150 KHz to 30MHz for emissions in each of the test modes.

3.4 Test Result

   Pass
   Remark:
   1. All modes were tested at AC 120V and 240V, only the worst result of AC 120V was reported.
   2. All modes of Low, Middle, and High channel were tested, only the worst result of High Channel was
   reported as below:


                                        Page 9 of 24                Report No.: UNIA2018112916FR-01



Temperature:      25℃                              Relative Humidity: 46%
Test Date:        Nov. 30, 2018                    Pressure:             1010hPa
Test Voltage:     AC 120V, 60Hz                    Phase:                Line
Test Mode:        Transmitting mode of GFSK 2480MHz




   Remark: Factor = Insertion Loss + Cable Loss, Result=Reading + Factor, Margin=Result – Limit.


                                        Page 10 of 24               Report No.: UNIA2018112916FR-01



Temperature:      25℃                              Relative Humidity: 46%
Test Date:        Nov. 30, 2018                    Pressure:             1010hPa
Test Voltage:     AC 120V, 60Hz                    Phase:                Neutral
Test Mode:        Transmitting mode of GFSK 2480MHz




   Remark: Factor = Insertion Loss + Cable Loss, Result=Reading + Factor, Margin=Result – Limit.


                                           Page 11 of 24                  Report No.: UNIA2018112916FR-01


4 RADIATED EMISSION TEST

 4.1 Radiation Limit
  For unintentional device, according to § 15.109(a), except for Class A digital devices, the field strength
  ofradiated emissions from unintentional radiators at a distance of 3 meters shall not exceed the
  followingvalues:
         Frequency                Distance                 Radiated                 Radiated
           (MHz)                  (Meters)                 (dBμV/m)                   (μV/m)
            30-88                     3                        40                       100
           88-216                     3                       43.5                      150
          216-960                     3                        46                       200
         Above 960                    3                        54                       500

  For intentional device, according to § 15.209(a), the general requirement of field strength of
  radiatedemissions from intentional radiators at a distance of 3 meters shall not exceed the above table.


 4.2 Test Setup

   1. Radiated Emission Test-Up Frequency Below 30MHz




   2. Radiated Emission Test-Up Frequency 30MHz~1GHz


                                          Page 12 of 24                  Report No.: UNIA2018112916FR-01


  3. Radiated Emission Test-Up Frequency Above 1GHz




4.3 Test Procedure
 1. Below 1GHz measurement the EUT is placed on turntable which is 0.8m above ground plane.
    And above 1GHz measurement EUT was placed on low permittivity and low tangent turn table
    which is 1.5m above ground plane.
 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level.
 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the
   highestemissions.
 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance.
 5. And also, each emission was to be maximized by changing the polarization of receiving antenna
   bothhorizontal and vertical.
 6. Repeat above procedures until the measurements for all frequencies are complete.
 7. The test frequency range from 9KHz to25GHz per FCC PART 15.33(a).

 Note:
 For battery operated equipment, the equipment tests shall be performed using a new battery.


4.4 Test Result

   PASS
   Remark:
   1. All the test modes completed for test. The worst case of Radiated Emissionis High channel, the test
   data of this mode was reported.
   2. By preliminary testing and verifying three axis (X, Y and Z) position of EUT transmitted status, it was
   found that “Z axis” position was the worst, and test data recorded in this report.
   3. Radiated emission test from 9KHz to 10th harmonic of fundamental was verified, and no emission
   found except system noise floor in 9KHz to 30MHz and not recorded in this report.


                                       Page 13 of 24               Report No.: UNIA2018112916FR-01


  Below 1GHz Test Results:

Temperature:      25℃                              Relative Humidity: 46%
Test Date:        Nov. 30, 2018                    Pressure:            1010hPa
Test Voltage:     AC 120V, 60Hz                    Polarization:        Horizontal
Test Mode:        Transmitting mode of GFSK2480MHz




   Remark: Absolute Level= Reading Level+ Factor, Margin= Absolute Level – Limit
           Factor=Ant. Factor + Cable Loss – Pre-amplifier


                                            Page 14 of 24                Report No.: UNIA2018112916FR-01



   Temperature:        25℃                              Relative Humidity: 46%
   Test Date:          Nov. 30, 2018                    Pressure:            1010hPa
   Test Voltage:       AC 120V, 60Hz                    Polarization:        Vertical
   Test Mode:          Transmitting mode of GFSK2480MHz




        Remark: Absolute Level= Reading Level+ Factor, Margin= Absolute Level – Limit
                Factor=Ant. Factor + Cable Loss – Pre-amplifier

Remark:
(1) Measuring frequencies from 9 KHz to the 1 GHz, Radiated emission test from 9KHz to 30MHzwas verified,
    and no any emission was found except system noise floor.
(2) * denotes emission frequency which appearing within the Restricted Bands specified in
    provision of 15.205, then the general radiated emission limits in 15.209 apply.
(3) The IF bandwidth of EMI Test Receiver between 30MHz to 1GHz was 120KHz, 1 MHz
    for measuring above 1 GHz, below 30MHz was 10KHz.


                                          Page 15 of 24               Report No.: UNIA2018112916FR-01


Above 1 GHz Test Results:
CH Low (2402MHz)

Horizontal:

                  Reading
     Frequency                   Factor      Emission Level     Limits       Margin
                   Result                                                              Detector
       (MHz)       (dBμV)         (dB)          (dBμV/m)      (dBμV/m)        (dB)      Type
       2402        108.62        -5.84           102.78          114         -11.22      PK

       2402         80.23        -5.84            74.39          94          -19.61      AV

       4804         61.69        -3.64            58.05          74          -15.95      PK

       4804         49.03        -3.64            45.39          54           -8.61      AV

       7206         58.62        -0.95            57.67          74          -16.33      PK

       7206         47.12        -0.95            46.17          54           -7.83      AV

   Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin= Absolute Level – Limit




Vertical:

                  Reading
     Frequency                   Factor      Emission Level     Limits       Margin
                   Result                                                              Detector
       (MHz)       (dBμV)         (dB)          (dBμV/m)      (dBμV/m)        (dB)      Type
       2402        107.63        -5.84           101.79          114         -12.21      PK

       2402         81.65        -5.84            75.81          94          -18.19      AV

       4804         61.53        -3.64            57.89          74          -16.11      PK

       4804         50.68        -3.64            47.04          54           -6.96      AV

       7206         57.63        -0.95            56.68          74          -17.32      PK

       7206         46.58        -0.95            45.63          54           -8.37      AV

   Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin= Absolute Level – Limit


                                          Page 16 of 24                Report No.: UNIA2018112916FR-01


CH Middle (2440MHz)

Horizontal:
                  Reading
     Frequency                   Factor      Emission Level     Limits        Margin
                   Result                                                               Detector
       (MHz)       (dBμV)         (dB)          (dBμV/m)      (dBμV/m)         (dB)      Type
       2440        109.52        -5.71           103.81          114          -10.19      PK

       2440         50.61        -5.71            44.90           94          -49.10      AV

       4880         61.23        -3.51            57.72           74          -16.28      PK

       4880         51.32        -3.51            47.81           54           -6.19      AV

       7320         56.68        -0.82            55.86           74          -18.14      PK

       7320         45.65        -0.82            44.83           54           -9.17      AV

   Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin = Absolute Level – Limit



Vertical:

                  Reading
     Frequency                   Factor      Emission Level     Limits        Margin
                   Result                                                               Detector
       (MHz)       (dBμV)         (dB)          (dBμV/m)      (dBμV/m)         (dB)      Type
       2440        110.23        -5.71           104.52          114           -9.48      PK

       2440         81.36        -5.71            75.65           94          -18.35      AV

       4880         60.85        -3.51            57.34           74          -16.66      PK

       4880         50.63        -3.51            47.12           54           -6.88      AV

       7320         56.63        -0.82            55.81           74          -18.19      PK

       7320         46.53        -0.82            45.71           54           -8.29      AV

   Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin= Absolute Level – Limit


                                           Page 17 of 24                  Report No.: UNIA2018112916FR-01

CH High (2480MHz)
Horizontal:
                   Reading
     Frequency                    Factor      Emission Level       Limits        Margin
                    Result                                                                 Detector
       (MHz)        (dBμV)          (dB)         (dBμV/m)         (dBμV/m)        (dB)       Type
       2480         110.53         -5.65           104.88            114          -9.12       PK

       2480          52.23         -5.65           46.58             94          -47.42       AV

       4960          62.07         -3.43           58.64             74          -15.36       PK

       4960          50.36         -3.43           46.93             54           -7.07       AV

       7440          56.58         -0.75           55.83             74          -18.17       PK

       7440          47.36         -0.75           46.61             54           -7.39       AV

   Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin= Absolute Level – Limit


Vertical:

                   Reading
     Frequency                    Factor      Emission Level       Limits        Margin
                    Result                                                                 Detector
       (MHz)        (dBμV)          (dB)         (dBμV/m)         (dBμV/m)        (dB)       Type
       2480         110.61         -5.65           104.96            114          -9.04       PK

       2480          81.87         -5.65           76.22             94          -17.78       AV

       4960          61.23         -3.43           57.80             74          -16.20       PK

       4960          49.85         -3.43           46.42             54           -7.58       AV

       7440          56.23         -0.75           55.48             74          -18.52       PK

       7440          47.12         -0.75           46.37             54           -7.63       AV

   Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin= Absolute Level – Limit


       Remark:
       (1) Measuring frequencies from 1 GHz to the 25 GHz.
       (2) “F” denotes fundamental frequency; “H” denotes spurious frequency. “E” denotes band edge
       frequency.
       (3) * denotes emission frequency which appearing within the Restricted Bands specified in
       provision of 15.205, then the general radiated emission limits in 15.209 apply.
       (4) Data of measurement within this frequency range shown “--- ” in the table above means the
       reading of emissions are attenuated more than 20dB below the permissible limits or the field
       strength is too small to be measured.
       (5) The IF bandwidth of EMI Test Receiver between 30MHz to 1GHz was 120KHz, 1 MHz for
       measuring above 1 GHz, below 30MHz was 10KHz.The resolution bandwidth of test
       receiver/spectrum analyzer is 1MHzand video bandwidth is 3MHz for peak measurement with
       peak detectorat frequency above 1GHz.The resolution bandwidth of test receiver/spectrum
       analyzer is 1MHzand video bandwidth is 10Hz for Average measurement with peak
       detection at frequency above 1GHz.
       (6) When the test results of Peak Detected below the limits of Average Detected, the Average
       Detected is not need completed. For example: Top Channel at Fundamental 73.16dBuV/m(PK
       Value) <93.98(AV Limit), at harmonic 53.20 dBuV/m(PK Value) <54 dBuV/m(AV Limit), the
       Average Detected not need to completed.
       (7)All modes of operation were investigated and the worst-case emissionsare reported.


                                            Page 18 of 24                 Report No.: UNIA2018112916FR-01


5 BAND EDGE

   5.1 Limits
   FCC PART 15.249(d) Emissions radiated outside of the specified frequency bands, except for
   harmonics,shall be attenuated by at least 50 dB below the level of the fundamental or to the general
   radiated emissionlimits in §15.209, whichever is the lesser attenuation.

   5.2 Test Procedure
   The band edge compliance of RF radiated emission should be measured by following the guidance
   in ANSIC63.10 with respect to maximizing the emission by rotating the EUT, measuring the emission
   while the EUT issituated in three orthogonal planes (if appropriate), adjusting the measurement antenna
   height andpolarization etc. Set RBW to 100KHz and VBM to 300KHz to measure the peak field strength
   and setRBW to 1MHz and VBW to 10Hz to measure the average radiated field strength.The conducted
   RF band edge was measured by using a spectrum analyzer. Set span wide enough to capture
   the highest in-band emission and the emission at the band edge. Set RBW to 100 KHz and VBW to
   300 KHz,to measure the conducted peak band edge.

   5.3 Test Result

       PASS
 Radiated Band Edge Test:
 Operation Mode: TX CH Low (2402MHz)
 Horizontal:
  Frequency     Reading Result     Factor      Emission Level      Limits        Margin
                                                                                              Detector
    (MHz)            (dBμV)         (dB)          (dBμV/m)        (dBμV/m)        (dB)         Type

    2310             56.23          -5.81          50.42             74          -23.58         PK

    2310               /            -5.81             /              54             /           AV

    2390             56.42          -5.84          50.58             74          -23.42         PK

    2390               /            -5.84             /              54             /           AV

    2400             57.58          -5.84          51.74             74          -22.26         PK

    2400               /            -5.84             /              54             /           AV

 Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier.


 Vertical:
  Frequency     Reading Result     Factor      Emission Level      Limits        Margin       Detector
                                                                                               Type
    (MHz)            (dBμV)         (dB)          (dBμV/m)        (dBμV/m)        (dB)

    2310             55.36          -5.81          49.55             74          -24.45          PK

    2310               /            -5.81             /              54             /            AV

    2390             55.69          -5.84          49.85             74          -24.15          PK

    2390               /            -5.84             /              54             /            AV

    2400             57.23          -5.84          51.39             74          -22.61          PK

    2400               /            -5.84             /              54             /            AV

 Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier.


                                          Page 19 of 24                Report No.: UNIA2018112916FR-01



Operation Mode: TX CH High (2480MHz)
Horizontal:
 Frequency    Reading Result     Factor      Emission Level      Limits       Margin     Detector
   (MHz)          (dBμV)           (dB)         (dBμV/m)        (dBμV/m)       (dB)       Type

  2483.5           57.21          -5.65          51.56            74          -22.42       PK

  2483.5             /            -5.65             /             54            /          AV

   2500            56.85          -5.72          51.13            74          -20.42       PK

   2500              /            -5.72             /             54            /          AV

Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier.



Vertical:
 Frequency    Reading Result     Factor      Emission Level      Limits       Margin
                                                                                         Detector
   (MHz)          (dBμV)           (dB)         (dBμV/m)        (dBμV/m)       (dB)       Type

  2483.5           56.87          -5.65          51.22            74          -22.78       PK

  2483.5             /            -5.65             /             54            /          AV

   2500            55.36          -5.72          49.64            74          -24.36       PK

   2500              /            -5.72             /             54            /          AV

Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier.


                                        Page 20 of 24                Report No.: UNIA2018112916FR-01


6 OCCUPIED BANDWIDTH MEASUREMENT


6.1 Test Setup
   Same asRadiated Emission Measurement


6.2 Test Procedure
  1. The EUT was placed on a turn table which is 0.8m above ground plane.
  2. Set EUT as normal operation.
  3. Based on ANSI C63.10 section 6.9.2: RBW=30KHz. VBW=100KHz, Span=3MHz.
  4. The useful radiated emission from the EUT was detected by the spectrum analyzer with peak detector.


6.3 Measurement Equipment Used

   Same asRadiated Emission Measurement


6.4 Test Result

    PASS

                    Frequency              20dB Bandwidth
                                                                          Result
                      (MHz)                    (MHz)
                      2402                      1.076                     PASS
                      2440                      1.081                     PASS
                      2480                      1.099                     PASS


         CH:2402MHz


             Page 21 of 24   Report No.: UNIA2018112916FR-01



CH:2440MHz




CH:2480MHz


                                        Page 22 of 24                 Report No.: UNIA2018112916FR-01




7 ANTENNA REQUIREMENT

 Standard Applicable:
 For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be
 designed toensure that no antenna other than that furnished by the responsible party shall be used
 with the device.

 Antenna Connected Construction
 The antenna used in this product is a PCB Antenna, The directional gains of antenna used for
 transmitting is 1dBi.

 ANTENNA:


                       Page 23 of 24   Report No.: UNIA2018112916FR-01


8 PHOTOGRAPH OF TEST


8.1Radiated Emission


                        Page 24 of 24         Report No.: UNIA2018112916FR-01


8.2Conducted Emission




                        ***End of Report***



Document Created: 2018-12-07 16:33:10
Document Modified: 2018-12-07 16:33:10

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC