14_IPVDW01 TestRpt r1

FCC ID: 2AQY5-IPVDW01

Test Report

Download: PDF
FCCID_4006264


Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 Table of Contents 1. GENERAL INFORMATION ................................................................................................ 5 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST ................................................................. 5 1.2 RELATED SUBMITTAL(S) / GRANT (S) ............................................................................................ 7 1.3 TEST METHODOLOGY .................................................................................................................. 7 1.4 EQUIPMENT MODIFICATIONS ........................................................................................................ 7 1.5 SUPPORT DEVICE ....................................................................................................................... 7 1.6 TEST FACILITY AND LOCATION ..................................................................................................... 8 1.7 SUMMARY OF TEST RESULTS ....................................................................................................... 9 2. SYSTEM TEST CONFIGURATION .................................................................................. 10 2.1 EUT CONFIGURATION ............................................................................................................... 10 2.2 SPECIAL ACCESSORIES ............................................................................................................. 10 2.3 DESCRIPTION OF TEST MODES ................................................................................................... 10 2.4 EUT EXERCISE ......................................................................................................................... 10 3. CONDUCTED EMISSIONS TEST .................................................................................... 11 3.1 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................ 11 3.2 TEST CONDITION ....................................................................................................................... 11 3.3 MEASUREMENT RESULTS .......................................................................................................... 11 4. MAX. CONDUCTED OUTPUT POWER ........................................................................... 12 4.1 MEASUREMENT PROCEDURE ..................................................................................................... 12 4.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................ 12 4.3 MEASUREMENT RESULTS .......................................................................................................... 12 5. 6DB BANDWIDTH ............................................................................................................ 13 5.1 MEASUREMENT PROCEDURE ..................................................................................................... 13 5.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................ 13 5.3 MEASUREMENT RESULTS .......................................................................................................... 13 6. POWER SPECTRAL DENSITY........................................................................................ 16 6.1 MEASUREMENT PROCEDURE ..................................................................................................... 16 6.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................ 16 6.3 MEASUREMENT RESULTS .......................................................................................................... 16 7. BAND EDGE AND CONDUCTED SPURIOUS EMISSIONS ........................................... 19 7.1 REQUIREMENT AND MEASUREMENT PROCEDURE ........................................................................ 19 7.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................ 19 7.3 MEASUREMENT RESULTS .......................................................................................................... 19 Page 2 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 8. RADIATED SPURIOUS EMISSIONS AND RESTRICTED BANDS ................................. 25 8.1 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ................................................................ 25 8.2 MEASUREMENT PROCEDURE ..................................................................................................... 26 8.3 LIMIT ........................................................................................................................................ 27 8.4 MEASUREMENT RESULTS ................................................................................................. 27 9. ANTENNA APPLICATION ............................................................................................... 31 9.1 ANTENNA REQUIREMENT............................................................................................................ 31 9.2 MEASUREMENT RESULTS .......................................................................................................... 31 10. TEST EQUIPMENT LIST................................................................................................ 32 Page 3 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 Revision History of This Test Report Report Number Description Issued Date NTC1805215FV00 Initial Issue 2018-07-06 Page 4 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 1. GENERAL INFORMATION 1.1 Product Description for Equipment under Test Product Name : DIWI Main Model Name : IPVDW01 Additional Model Name : N/A Model difference : N/A Brand Name : N/A Power Supply : DC 8-28V Adapter : N/A Test voltage : DC 12V, DC 24V Only the worst case was recorded in the report. Hardware version : V1.0 Software version : V1.0 Serial number : N/A Note : N/A Technical parameters Frequency Range : 904-926MHz Modulation : GFSK Number of Channel : 23 Channel space : 1MHz Antenna Type : External antenna Antenna Gain : 2.5dBi Page 5 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 Channel Frequency Channel Frequency No. (MHz) No. (MHz) 1 904 13 916 2 905 14 917 3 906 15 918 4 907 16 919 5 908 17 920 6 909 18 921 7 910 19 922 8 911 20 923 9 912 21 924 10 913 22 925 11 914 23 926 12 915 Note: According to section 15.31(m), regards to the operating frequency range over 10MHz, the Lowest, Middle, and the Highest frequency of channel were selected to perform the test. The selected frequency see below: Frequency Channel MHz 1 904 12 915 23 926 Page 6 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 1.2 Related Submittal(s) / Grant (s) This submittal(s) (test report) is intended for FCC ID: 2AQY5-IPVDW01 filing to comply with Section 15.247 of the FCC Part 15(2016), Subpart C Rule. 1.3 Test Methodology The radiated emission measurement was performed according to the procedures in ANSI C63.10 (2013). Radiated emission measurement was performed in semi-anechoic chamber. For radiated emission measurement, preliminary scans were performed in the semi-anechoic chamber only to determine the worst case modes. All radiated tests were performed at an antenna to EUT distance of 3 meters. All other measurements were made in accordance with the procedures in 47 CFR part 2. 1.4 Equipment Modifications Not available for this EUT intended for grant. 1.5 Support Device N/A Page 7 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 1.6 Test Facility and Location Site Description EMC Lab : Listed by CNAS, August 14, 2015 The certificate is valid until August 13, 2018 The Laboratory has been assessed and proved to be in compliance with CNAS/CL01 The Certificate Registration Number is L5795. Listed by A2LA, November 01, 2017 The certificate is valid until December 31, 2019 The Laboratory has been assessed and proved to be in compliance with ISO17025 The Certificate Registration Number is 4429.01 Listed by FCC, November 06, 2017 The Designation Number is CN1214 Test Firm Registration Number: 907417 Listed by Industry Canada, June 08, 2017 The Certificate Registration Number. Is 46405-9743 Name of Firm : Dongguan Nore Testing Center Co., Ltd. (Dongguan NTC Co., Ltd.) Site Location : Building D, Gaosheng Science & Technology Park, Zhouxi Longxi Road, Nancheng District, Dongguan City, Guangdong Province, China Page 8 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 1.7 Summary of Test Results FCC Rules Description Of Test Uncertainty Result Not §15.207 (a) AC Power Conducted Emission ±1.06dB applicable §15.247(b)(3) Max. Conducted Output Power ±1.06dB Compliant §15.247(a)(2) 6dB Bandwidth ±1.42 x10-4% Compliant §15.247(e) Power Spectral Density ±1.06dB Compliance Band Edge and Conducted §15.247(d) ±1.70dB Compliance Spurious Emissions §15.247(d),§15.209, Radiated Spurious Emissions and ±3.70dB Compliance §15.205 Restricted Bands §15.203 Antenna Requirement N/A Compliance Note: Due to this EUT is powered by DC power source only, the AC Power Conducted Emission is not applicable. Page 9 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 2. System Test Configuration 2.1 EUT Configuration The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions requirement and operating in a manner which intends to maximize its emission characteristics in a continuous normal application. 2.2 Special Accessories Not available for this EUT intended for grant. 2.3 Description of test modes The EUT has been tested under continuous operating condition (The duty cycle >98%). Test program used to control the EUT staying in continuous transmitting mode. The Lowest, Middle and highest channel were chosen for testing, and modulation type GFSK was tested, but only the worst case data is shown in this report. 2.4 EUT Exercise The EUT was operated in the engineering mode to fix the Tx frequency that was for the purpose of the measurements. Page 10 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 3. Conducted Emissions Test 3.1 Test SET-UP (Block Diagram of Configuration) 3.2 Test Condition Test Requirement: FCC Part 15.207 Frequency Range: 150KHz ~ 30MHz Detector: RBW 9KHz, VBW 30KHz Operation Mode: TX Mode 3.3 Measurement Results Not applicable. Page 11 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 4. Max. Conducted Output Power 4.1 Measurement Procedure Maximum Conducted Output power at Antenna Terminals, FCC Rules 15.247(b)(3): One of the following procedures may be used to determine the maximum peak conducted output power of a DTS EUT. The maximum peak conducted output power may be measured using a broadband peak RF power meter. The power meter shall have a video bandwidth that is greater than or equal to the DTS bandwidth and shall utilize a fast-responding diode detector. 4.2 Test SET-UP (Block Diagram of Configuration) EUT Power meter 4.3 Measurement Results Please refer to following table. Temperature : 24 ℃ Humidity : 50 % June 29, 2018, Test By: Sance Test Date : June 13, 2018 Test Result: PASS Peak Output Frequency Data Rate Limit Power MHz Mbps dBm dBm Low Channel: 904 1 16.03 30 Middle Channel: 915 1 16.08 30 High Channel: 926 1 15.75 30 Page 12 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 5. 6dB Bandwidth 5.1 Measurement Procedure DTS 6dB Channel Bandwidth, FCC Rule 15.247(a)(2): The antenna port of the EUT was connected to the input of a spectrum analyzer. Analyzer was set as below: 1. For 6dB bandwidth, Set the RBW = 100KHz. 2. Set the VBW ≥ 3 x RBW 3. Detector = peak. 4. Sweep time = auto couple. 5. Trace mode = max hold. 6. Allow trace to fully stabilize. 7. Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 6 dB relative to the maximum level measured in the fundamental emission. 5.2 Test SET-UP (Block Diagram of Configuration) EUT Spectrum Analyzer 5.3 Measurement Results Please refer to following table and plots. Temperature : 22 ℃ Humidity : 53 % June 13, 2018 Test By: Sance Test Date : June 29, 2018 Test Result: PASS 6dB Frequency Data Rate Bandwidth Limit MHz Mbps KHz Low Channel: 904 1 768.6 >500KHz Middle Channel: 915 1 766.4 >500KHz High Channel: 926 1 760.4 >500KHz Page 13 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 6dB bandwidth Low Channel 6dB bandwidth Middle Channel Page 14 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 6dB bandwidth High Channel Page 15 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 6. Power Spectral Density 6.1 Measurement Procedure DTS 6dB Channel Bandwidth, FCC Rule 15.247(a)(2): The antenna port of the EUT was connected to the input of a spectrum analyzer. Analyzer was set as below: 1. Set analyzer center frequency to DTS channel center frequency. 2. Set the span to 1.5 times the DTS bandwidth. 3. Set the RBW to: 3 kHz≤RBW≤100KHz 4. Set the VBW ≥ 3 x RBW. 5. Detector = peak. 6. Sweep time = auto couple. 7. Trace mode = max hold. 8. Allow trace to fully stabilize. 9. Use the peak marker function to determine the maximum amplitude level within the RBW. 10. If measured value exceeds limit, reduce RBW (no less than 3 kHz) and repeat. 6.2 Test SET-UP (Block Diagram of Configuration) EUT Spectrum Analyzer 6.3 Measurement Results Please refer to following table and plots. Temperature : 22 ℃ Humidity : 53 % June 13, 2018 Test By: Sance Test Date : June 29, 2018 Test Result: PASS Frequency Data Rate PSD Limit MHz Mbps dBm/3kHz dBm/3kHz Low Channel: 904 1 -4.16 8 Middle Channel: 915 1 -3.78 8 High Channel: 926 1 -4.36 8 Page 16 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 Low Channel Middle Channel Page 17 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 High Channel Page 18 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 7. Band Edge and Conducted Spurious Emissions 7.1 Requirement and Measurement Procedure In any 100KHz bandwidth outside the frequency band in which the spread spectrum intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20dB below that in the 100KHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement. The antenna port of the EUT was connected to the input of a spectrum analyzer. Analyzer was set as below. A Quasi-peak measurement was then made for that frequency point for below 1GHz test. PK and AV for above 1GHz emission test. During the radiated emission test, the spectrum analyzer was set with the following configurations: Frequency Band Level Resolution Bandwidth Video Bandwidth (MHz) 30 to 1000 QP 120 kHz 300 kHz Peak 1 MHz 3 MHz Above 1000 Average 1 MHz 10 Hz 7.2 Test SET-UP (Block Diagram of Configuration) EUT Spectrum Analyzer 7.3 Measurement Results The test plots and table showed all spurious emission and up to the tenth harmonic was measured and they were found to be at least 20dB below the highest level of the desired power in the passband. Please refer to below plots. Page 19 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 Spurious Emission in restricted band: Operation Mode: TX Test Date : July 02, 2018 Frequency Range: Above 1GHz Temperature : 24 ℃ Test Result: PASS Humidity : 47 % Measured Distance: 3m Test By: Sance Emission Reading Limit 3m Margin Freq. Ant.Pol. Factor Level Level(dBuV) (dBuV/m) (dB) (MHz) (H/V) (dB/m) (dBuV) QP QP QP QP 902.00 H 39.20 -1.19 38.01 46.00 -7.99 902.00 V 24.90 -1.19 23.71 46.00 -22.29 928.00 H 28.25 -0.67 27.58 46.00 -18.42 928.00 V 29.01 -0.67 28.34 46.00 -17.66 Note: (1) All Readings are Peak Value and AV. (2) Emission Level= Reading Level+Probe Factor +Cable Loss (3) Measurement uncertainty : ±3.7dB Page 20 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 Band Edge Low Channel High Channel Page 21 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 Conducted Spurious Emissions Low Channel Page 22 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 Middle Channel Page 23 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 High Channel Note: Sweep points=30001pts Page 24 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 8. Radiated Spurious Emissions and Restricted Bands 8.1 Test SET-UP (Block Diagram of Configuration) 8.1.1 Radiated Emission Test Set-Up, Frequency Below 30MHz Turntable 3m EUT Test 0.8 m Receiver Ground Plane Coaxial Cable Page 25 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 8.1.2 Radiated Emission Test Set-Up, Frequency above 1GHz 3m Turntable 4m EUT Spectrum 1.5m Amplifier Analyzer 8.2 Measurement Procedure a. Blow 1GHz, the EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi- anechoic chamber room. b. For the radiated emission test above 1GHz: The EUT was placed on the top of a rotating table 1.5 meters above the ground at a 3 meter full anechoic chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. Place the measurement antenna away from each area of the EUT determined to be a source of emissions at the specified measurement distance, while keeping the measurement antenna aimed at the source of emissions at each frequency of significant emissions, with polarization oriented for maximum response. The measurement antenna may have to be higher or lower than the EUT, depending on the radiation pattern of the emission and staying aimed at the emission source for receiving the maximum signal. The final measurement antenna elevation shall be that which maximizes the emissions. The measurement antenna elevation for maximum emissions shall be restricted to a range of heights of from 1 m to 4 m above the ground or reference ground plane. c. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. d. The height of antenna is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. e. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. The test-receiver system was set to peak detect function and specified bandwidth with maximum hold mode. f. A Quasi-peak measurement was then made for that frequency point for below 1GHz test. PK and AV for above 1GHz emission test. Page 26 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 During the radiated emission test, the spectrum analyzer was set with the following configurations: Frequency Band Level Resolution Bandwidth Video Bandwidth (MHz) 30 to 1000 QP 120 kHz 300 kHz Peak 1 MHz 3 MHz Above 1000 Average 1 MHz 10 Hz 8.3 Limit Frequency range Distance Meters Field Strengths Limit (15.209) MHz V/m 0.009 ~ 0.490 300 2400/F(kHz) 0.490 ~ 1.705 30 24000/F(kHz) 1.705 ~ 30 30 30 30 ~ 88 3 100 88 ~ 216 3 150 216 ~ 960 3 200 Above 960 3 500 Remark：(1) Emission level (dB)V = 20 log Emission level V/m (2) The smaller limit shall apply at the cross point between two frequency bands. (3) As shown in 15.35(b), for frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation. (4) The frequency range scanned is from the lowest radio frequency signal generated in the device which is greater than 9 kHz to the tenth harmonic of the highest fundamental frequency or 40 GHz, whichever is lower. (5) §15.247(d) specifies that emissions which fall in the restricted bands, as defined in §15.205 comply with radiated emission limits specified in §15.209. 8.4 Measurement Results Please refer to following plots of the worst case (Middle channel). Page 27 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 DIWI Note: Below 30MHz, the emissions are lower than 20dB below the allowable limit. Page 28 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 DIWI Note: Below 30MHz, the emissions are lower than 20dB below the allowable limit. Page 29 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 Frequency Range: 1-10GHz Test Date : July 02, 2018 Test Result: PASS Temperature : 24 ℃ Measured Distance: 3m Humidity : 47 % Test By: Sance Reading Emission Level Limit 3m Margin Freq. Ant.Pol. Factor Level(dBuV) (dBuV) (dBuV/m) (dB) (MHz) (H/V) (dB/m) PK AV PK AV PK AV PK AV Operation Mode: TX Mode (Low) 1808 V 57.88 46.08 -3.38 54.50 42.70 74.00 54.00 -19.50 -11.30 2399 V 49.99 40.08 0.13 50.12 40.21 74.00 54.00 -23.88 -13.79 --- 1808 H 54.45 43.52 -3.38 51.07 40.14 74.00 54.00 -22.93 -13.86 2399 H 48.99 39.23 0.13 49.12 39.36 74.00 54.00 -24.88 -14.64 --- Operation Mode: TX Mode (Mid) 1830 V 58.08 50.11 -3.10 54.98 47.01 74.00 54.00 -19.02 -6.99 2745 V 48.49 34.05 1.26 49.75 35.31 74.00 54.00 -24.25 -18.69 --- 1830 H 59.91 51.46 -3.10 56.81 48.36 74.00 54.00 -17.19 -5.64 2745 H 48.66 33.68 1.26 49.92 34.94 74.00 54.00 -24.08 -19.06 --- Operation Mode: TX Mode (High) 1852 V 53.32 43.90 -2.82 50.50 41.08 74.00 54.00 -23.50 -12.92 2778 V 47.13 32.16 1.34 48.47 33.50 74.00 54.00 -25.53 -20.50 --- 1852 H 55.49 40.97 -2.82 52.67 38.15 74.00 54.00 -21.33 -15.85 2778 H 47.97 32.75 1.34 49.31 34.09 74.00 54.00 -24.69 -19.91 --- Other harmonics emissions are lower than 10dB below the allowable limit. Note: (1) All Readings are Peak Value and AV. (2) Emission Level= Reading Level + Factor (3) Factor= Antenna Gain + Cable Loss – Amplifier Gain (4) Data of measurement within this frequency range shown “ ---” in the table above means the reading of emissions are attenuated more than 10dB below the permissible limits. (5) Measurement uncertainty : ±3.7dB. (6) Horn antenna used for the emission over 1000MHz. Page 30 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 9. Antenna Application 9.1 Antenna requirement According to of FCC part 15C section 15.203 and 15.240: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. Systems operating in the 902-928MHz band that are used exclusively for fixed, point-to-point operations may employ transmitting antennas with directional gain greater than 6dBi provided the maximum peak output power of the intentional radiator is reduced by 1dB for every 3dB that the directional gain of the antenna exceeds 6dBi. 9.2 Measurement Results The antenna is External antenna that no antenna other than furnished by the responsible party shall be used with the device, and the best case gain of the antenna is 2.5dBi, So, the antenna is consider meet the requirement. Page 31 of 32

Dongguan Nore Testing Center Co., Ltd. Report No.: NTC1805215FV00 FCC ID: 2AQY5-IPVDW01 10. Test Equipment List Description Manufacturer Model Number Serial Characteristics Calibration Calibration Number Date Due Date Test Receiver Rohde & Schwarz ESCI7 100837 9KHz~7GHz Mar. 13, 2018 Mar. 12, 2019 Antenna Schwarzbeck VULB9162 9162-010 30MHz~7GHz Mar. 14, 2018 Mar. 13, 2019 Cable Huber+Suhner CBL2-NN-1M 22390001 9KHz~7GHz Mar. 13, 2018 Mar. 12, 2019 Cable Huber+Suhner CIL02 N/A 9KHz~7GHz Mar. 13, 2018 Mar. 12, 2019 RF Cable Huber+Suhner SF-104 MY16559/4 9KHz~25GHz Apr. 25, 2018 Apr. 25, 2019 Power Amplifier HP HP 8447D 1145A00203 100KHz~1.3GHz Mar. 13, 2018 Mar. 12, 2019 Horn Antenna Schwarzbeck BBHA9170 9170-242 15GHz~40GHz Mar. 13, 2018 Mar. 12, 2019 Horn Antenna Com-Power AH-118 071078 1GHz~18GHz Mar. 14, 2018 Mar. 13, 2019 RF Cable Huber+Suhner SF-104 N/A 9KHz~40GHz Apr. 25, 2018 Apr. 25, 2019 Loop antenna Daze ZA30900A 0708 9KHz~30MHz Apr. 25, 2018 Apr. 25, 2019 Spectrum Rohde & Schwarz FSU26 200409/026 20Hz~26.5GHz Apr. 25, 2018 Apr. 25, 2019 Analyzer Spectrum Rohde & Schwarz FSV40 101003 10Hz~40GHz Apr. 06, 2018 Apr. 05, 2019 Analyzer Pre-Amplifier EMCI EMC 184045 980102 18GHz~40GHz Nov. 03, 2017 Nov. 02, 2018 Pre-Amplifier Agilent 8449B 3008A02964 1GHz~26.5GHz Apr. 25, 2018 Apr. 25, 2019 L.I.S.N. Rohde & Schwarz ENV 216 101317 9KHz~30MHz Mar. 13, 2018 Mar. 12, 2019 Temporary antenna TESCOM SS402 N/A 9KHz-25GHz N/A N/A connector Power Meter Anritsu ML2495A 1139001 100k-65GHz Nov. 03, 2017 Nov. 02, 2018 Power Sensor Anritsu MA2411B 100345 300M-40GHz Nov. 03, 2017 Nov. 02, 2018 Note: The temporary antenna connector is soldered on the PCB board in order to perform conducted tests and this temporary antenna connector is listed in the equipment list. ---End--- Page 32 of 32


Document Created: 2018-09-14 09:25:19
Document Modified: 2018-09-14 09:25:19
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC