User manual

FCC ID: 2AQURWF31

Users Manual

Download: PDF
FCCID_4403348

Installation Manual Meet your new smart switch ! Single switch Now Before Line D Neutral Ground Wi-Fi Smart Dimmer Switch C C Smart • WF31 • B Dimmer A B A Smart Switch x1 Faceplate x1 wiring x1 screws x2 Line Dimmer D Neutral From source From source Ground Specifications: Part 1. Installation 3-Way switch option 1 Power: 120V AC, 60Hz Wireless Frequency: 2.4GHz Eva Logik smart switch will turn your switch into a smart one. All you need to do is to do some basic Neutral Wireless Standard: IEEE802.11b/g/n Before Now common common Maximum Load: 150W LED, 500 W incandescent wiring work. Line (300W with both sides of heat sink tabs off) D Minimum Load: 5W for LED bulbs Ground 1. Let’s get started. Range: Up to 100 feet line of sight For indoor use. C E We will guide you through the whole wiring process. If Smart you are not sure about the basic wiring work, please call Dimmer an electrician. A common common B Smart common Dimmer common 2. Check Wi-Fi signal. Line 5. Detach old switch Neutral Please make sure that your switch is in the area None connect None connect From source From source Ground with strong Wi-Fi signal. Unscrew the top and bottom screws of the 3. Tools switch to detach it from the wall. 3-Way switch option 2 OLD Please prepare a flat head screwdriver,a wire common common stripper and a volt meter. Just in case you Line 6. Double check Before might need them. Now D Neutral You can use voltage detector here to make sure 4. Turn off circuit breaker there is no power going through the wires. Ground Find your light control in your circuit breaker and turn C E it off. Make sure the power is off by flipping your - --.- Smart OFF switch several times. Dimmer A B 7. Identify the wires. D Wiring Instructions - A Few Quick Reminders common common A. LINE (Hot) — Black Line Smart Dimmer common (connected to power) A quick note before we give out the wiring schematics. common Please do not try installing this device if you are unsure Neutral B. NEUTRAL — White C E of how electrical circuits operate within your home. As Ground C. LOAD — Black exciting as it is to have a smart switch installed, it can be From source From source (connected to lighting) dangerous and even life-threatening if you do not install D. GROUND — Green/Bare this correctly. Please consult a qualified electrician if A B necessary. With that said, here are a few other warnings 8. Turn on circuit breaker 9. Check the Wi-Fi light. E. TRAVELER — Red/Other we’d like to point out for your safety: (only in 3-way in stallations) Turn on your switch’s power from the circuit breaker. Press the switch After the switch is configured successfully with the Smart Life APP, the indicator will not ON Common several times to check whether it works. blink. If the switches are not configured to the Smart Life APP, the indicator will have an Orange light on.

Part 2. Manual Control FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: Tapx1( Top rocker) : turn on the light(the last brightness level) (1) this device may not cause harmful interference, and Press and hold (Top rocker): add brightness (2) this device must acceptany interference received, including interference that may cause undesired operation. Tapx1(bottom rocker) : turn off the light changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to Press and hold (bottom rocker) : reduce brightness. operate the equipment. 4 6 Tapx3(Top or bottom rocker) then hold 10s until the Wi-Fi status LED blinks rapidly to initiate App-Config Mode. Enter the Wi-Fi Password 7 NOTE: This equipment has been tested and found to comply with (Your phone should have 5 Edit the name of your new smart switch! Click the new smart the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection Solid 10s & Flash 1 time: connected to the same Wait for the app to switch you just added against harmful interference in a residential installation. This Operation again,Until success Wi-Fi first). connect to your Wi-Fi and you can start using equipment generates, uses and can radiate radio frequency energy until it’s 100% it now. and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, Air-Gap Switch: there is no guarantee that interference will not occur in a particular Pull out for Bulb replacement installation. Push back for normal use. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the Part 3. APP Connection interference by one or more of the following measures: -- Reorient or relocate the receiving antenna. Tap here to turn -- Increase the separation between the equipment and receiver. on/off the switch -- Connect the equipment into an outlet on a circuit different from 3. The smart switch can be also used with Amazon Echo and that to which the receiver is connected. Google Home. Please scan the QR code below and follow the -- Consult the dealer or an experienced radio/TV technician for help. instructions if you have any trouble pairing with them. FCC Radiation Exposure Statement: QR code Smart Life This equipment complies with FCC radiation exposure limits set C forth for an uncontrolled environment . 1. Please scan the QR code to download the application “Smart Life”. 2. If you cannot download Smart Life app, please search B This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. “Smart Life” on Google Play (for Android phone) or Apple Store (for iOS phone) to download. After you download the Smart Life App and register a new account, CAUTION - PLEASE READ! please follow the instructions below to set up your sramt switch. Amazon-Echo Google-Home B A C This device (WF31) is intended for installation in accordance with the National Electric Code and local regulations in the • Tap “ A ” to turn on/off the light. United States, or the Canadian Electrical Code and local regula- • Tap “ B ” to adjust the brightness of the light. tions in Canada. If you are unsure or uncomfortable about performing this installation consult a qualified electrician. • Tap “ C ” to set a timer to the switch. Remove Device WARNING - SHOCK HAZARD TURN OFF THE POWER to the circuit for the switch and lighting Note: fixture at the service panel (circuit breaker) prior to installation. 1)Our products only support 2.4GHz Wi-Fi network. ALL WIRING CONNECTIONS MUST BE MADE WITH THE POWER 2)Please operate quickly when LED indicator blinks rapidly. OFF to avoid personal injury and/or damage to the switch. 3 3) When indicator flash enters the network, complete standard operation within 30s Tap the switch 3 times and OTHER WARNINGS 1 hold for 10s. LED indicator 4) Flashing slowly enters AP Mode. (select “AP Mode” follow the default procedure) Tap ‘+’ to add a device in your app (Our products only support 2.4GHz 2 blinks rapidly. Risk of Fire Risk of Electrical Shock Select Risk of Burns Wi-Fi network.） Smart Lighting - Lighting Devices V5.0 www.nie-tech.com


Document Created: 2019-08-02 08:53:01
Document Modified: 2019-08-02 08:53:01
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC