Test Report_15B

FCC ID: 2AQQKWJ11

Test Report

Download: PDF
FCCID_4358117

Page 1 of 28 FCC Test Report Report No.: AGC00703190601FE01 PRODUCT DESIGNATION : 2.4G Camera BRAND NAME : Howell MODEL NAME : WJ11, WJ12, WJ13, WJ14, WJ15 APPLICANT : Shenzhen Howell Intelligent Technology Co.,Ltd. DATE OF ISSUE : Jul. 12, 2019 STANDARD(S) : FCC Part 15 Subpart B REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context.

Report No.: AGC00703190601FE01 Page 2 of 28 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jul. 12, 2019 Valid Initial release

Report No.: AGC00703190601FE01 Page 3 of 28 TABLE OF CONTENTS 1. VERIFICATION OF CONFORMITY .......................................................................................................4 2. SYSTEM DESCRIPTION .......................................................................................................................5 3. MEASUREMENT UNCERTAINTY .........................................................................................................5 4. PRODUCT INFORMATION ....................................................................................................................6 5. SUPPORT EQUIPMENT ........................................................................................................................7 6. TEST FACILITY .....................................................................................................................................8 7. TEST ITEMS AND THE RESULTS ........................................................................................................9 8. FCC LINE CONDUCTED EMISSION TEST ........................................................................................10 8.1. LIMITS OF LINE CONDUCTED EMISSION TEST.........................................................................10 8.2. BLOCK DIAGRAM OF TEST SETUP ............................................................................................10 8.3. PROCEDURE OF LINE CONDUCTED EMISSION TEST ............................................................. 11 8.4. TEST RESULT OF LINE CONDUCTED EMISSION TEST ............................................................12 9. RADIATED EMISSION TEST ..............................................................................................................14 9.1. LIMITS OF RADIATED EMISSION TEST ......................................................................................14 9.2. BLOCK DIAGRAM OF TEST SETUP ............................................................................................14 9.3. PROCEDURE OF RADIATED EMISSION TEST ...........................................................................15 9.4. TEST RESULT OF RADIATED EMISSION TEST ..........................................................................16 APPENDIX A: PHOTOGRAPHS OF TEST SETUP ................................................................................18 APPENDIX B: PHOTOGRAPHS OF EUT ...............................................................................................20

Report No.: AGC00703190601FE01 Page 4 of 28 1. VERIFICATION OF CONFORMITY Applicant Shenzhen Howell Intelligent Technology Co.,Ltd. 5/F, No.13 Building, Nangang 2ndIndustrial Park, Songbai Road, Xili Town, Address NanShan District, Shenzhen, China 518055 Manufacturer Shenzhen Howell Intelligent Technology Co.,Ltd. 5/F, No.13 Building, Nangang 2ndIndustrial Park, Songbai Road, Xili Town, Address NanShan District, Shenzhen, China 518055 Factory Shenzhen Howell Intelligent Technology Co.,Ltd. 5/F, No.13 Building, Nangang 2ndIndustrial Park, Songbai Road, Xili Town, Address NanShan District, Shenzhen, China 518055 Product Designation 2.4G Camera Brand Name Howell Test Model WJ11 Measurement Procedure ANSI C63.4: 2014 Date of test Jun. 20, 2019 to Jul. 12, 2019 Deviation None Condition of Test Sample Normal Test Result Pass Report Template AGCRT-US-IT/AC The above equipment was tested by Attestation of Global Compliance (Shenzhen) Co., Ltd. for compliance with the requirements set forth in the FCC Rules and Regulations Part 15, the measurement procedure according to ANSI C63.4:2014. This said equipment in the configuration described in this report shows the maximum emission levels emanating from equipment are within the compliance requirements. The test results of this report relate only to the tested sample identified in this report. Tested By Calvin Liu(Liu Junchen) Jul. 12, 2019 Reviewed By Max Zhang(Zhang Yi) Jul. 12, 2019 Approved By Forrest Lei(Lei Yonggang) Jul. 12, 2019 Authorized Officer

Report No.: AGC00703190601FE01 Page 5 of 28 2. SYSTEM DESCRIPTION TEST MODE DESCRIPTION NO. TEST MODE DESCRIPTION WORST 1 Video with Charging mode V 2 Camera with Charging mode -- 3 TF Card with Charging mode -- Note: 1. V means EMI worst mode. 2. Only the data of the worst mode would be recorded in this report. 3. MEASUREMENT UNCERTAINTY The uncertainty is calculated using the methods suggested in the “Guide to the Expression of Uncertainty in measurement” (GUM) published by CISPR and ANSI. - Uncertainty of Conducted Emission, Uc = ±3.2 dB - Uncertainty of Radiated Emission below 1GHz, Uc = ±3.9 dB - Uncertainty of Radiated Emission above 1GHz, Uc = ±4.8 dB

Report No.: AGC00703190601FE01 Page 6 of 28 4. GENERAL DESCRIPTION Highest Operating Frequency 2.462GHz Hardware Version XWL_WJ11_MainBoard_Rev1.5 2019.04.17 Software Version 21.117.0.7.50 Antenna Designation Integrated antenna Antenna Gain 2dBi Power Supply DC 5V by adapter or DC 3.7V by Battery I/O Port Information ( Applicable Not Applicable) I/O Port of EUT I/O Port Type Number Specific Tested With USB Port 1 1.00m Unshielded 1 TF port 1 -- 1

Report No.: AGC00703190601FE01 Page 7 of 28 5. SUPPORT EQUIPMENT Data Power Device Type Manufacturer Model Name Serial No. Cable Cable Adapter Jihongda JHD-AP006U-050100BB-2 -- -- -- Note： 1 “-- “means no any support device during testing.

Report No.: AGC00703190601FE01 Page 8 of 28 6. TEST FACILITY Test Site Attestation of Global Compliance (Shenzhen) Co., Ltd 1-2/F, Building 19, Junfeng Industrial Park, Chongqing Road, Heping Community, Location Fuhai Street, Bao'an District, Shenzhen, Guangdong, China TEST EQUIPMENT OF CONDUCTED EMISSION TEST Equipment Manufacturer Model S/N Cal. Date Cal. Due TEST RECEIVER R&S ESPI 101206 Jun.12, 2019 Jun.11, 2020 LISN R&S ESH2-Z5 100086 Aug. 28, 2018 Aug. 27, 2019 TEST EQUIPMENT OF RADIATED EMISSION TEST Equipment Manufacturer Model S/N Cal. Date Cal. Due TEST RECEIVER R&S ESCI 10096 Jun.12, 2019 Jun.11, 2020 EXA Signal Aglient N9010A MY53470504 Dec.07, 2018 Dec.08, 2019 Analyzer Horn antenna SCHWARZBECK BBHA 9170 #768 Sep. 21,2017 Sep. 20,2020 Double-Ridged ETS LINDGREN 3117 00034609 May. 26,2018 May. 25,2020 Waveguide Horn Broadband SCHWARZBECK BBV 9718 9718-205 Jun.12, 2019 Jun.11, 2020 Preamplifier ANTENNA SCHWARZBECK VULB9168 D69250 Sep.28, 2018 Sep.27,2019

Report No.: AGC00703190601FE01 Page 9 of 28 7. TEST ITEMS AND THE RESULTS Test item Test Requirement Test Method Class/Severity Result CONDUCTED FCC Part 15 Rules ANSI C63.4 Class B Pass EMISSION RADIATED FCC Part 15 Rules ANSI C63.4 Class B Pass EMISSION

Report No.: AGC00703190601FE01 Page 10 of 28 8. FCC LINE CONDUCTED EMISSION TEST 8.1. LIMITS OF LINE CONDUCTED EMISSION TEST Maximum RF Line Voltage Frequency Q.P.( dBuV) Average( dBuV) 150kHz-500kHz 66-56 56-46 500kHz-5MHz 56 46 5MHz-30MHz 60 50 Note: 1. The lower limit shall apply at the transition frequency. 2. The limit decreases linearly with the logarithm of the frequency in the range 0.15 MHz to 0.50MHz. 8.2. BLOCK DIAGRAM OF TEST SETUP

Report No.: AGC00703190601FE01 Page 11 of 28 8.3. PROCEDURE OF LINE CONDUCTED EMISSION TEST (1) The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. When the EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.4 (see Test Facility for the dimensions of the ground plane used). When the EUT is a floor-standing equipment, it is placed on the ground plane which has a 3-12 mm non-conductive covering to insulate the EUT from the ground plane. (2) Support equipment, if needed, was placed as per ANSI C63.4. (3) All I/O cables were positioned to simulate typical actual usage as per ANSI C63.4. (4) The EUT received AC120V/60Hz power from a LISN. (5) The EUT test program was started. Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver. (6) Analyzer / Receiver scanned from 150 kHz to 30MHz for emissions in each of the test modes. (7) During the above scans, the emissions were maximized by cable manipulation. (8) A scan was taken on both power lines, Line 1 and Line 2, recording at least the six highest emissions. (9) Emission frequency and amplitude were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit. If EUT emission level was less –2dB to the A.V. limit in Peak mode, then the emission signal was re-checked using Q.P and Average detector. The test data of the worst case condition (mode 1) was reported on the Summary Data page.

f oL_~ 1 150k 300k 400k 6 Ok 800k 1M 2M 3M 20M 30M Frequency [Hz] x x iMES TEST_fin MEASUREMENT RESULT: "TESTfin" 6/27/2019 7:559M Frequency Level Transd Limit Margin Detector Line PE MHz dBuv adB dBuy dB 0.438000 39.60 10 .7 57 17.5 QP L1 FLO 0.806000 41.90 10 .8 56 14.1 QP L1 FLO 0.930000 42 .60 11 .2 56 13.4 QP L1 FLO 1.158000 41.20 11.5 56 14.8 QP L1 FLO 1.178000 42 .40 11.5 56 13.6 QP L1 FLO 21.286000 35.00 12.5 60 25.0 QP L1 FLO MEASUREMENT RESULT: "TEST_ fin2" 6/27/2019 7:559M Frequency Level Transd Limit Margin Detector Line PE MHz adBuv adB dBuvy dB 0.358000 31.20 10 .5 49 17.6 AV L1 FLO 0.802000 30.20 10 .8 46 15.8 AV L1 FLO 0.870000 32 .50 11.0 46 13.5 AV L1 FLO 1.002000 33.70 11 .4 46 12.3 AV L1 FLO 1.070000 33.30 11 .4 46 12.7 AV L1 FLO 20.914000 25.50 12.5 50 24.5 AV L1 FLO Attestation of Global Compliance(Shenzhen)Co.,Ltd. Add: 2/F., Building 2, No.1—4, Chaxi Sanwei Technial Industrial Park, Gushu, Xixiang, Bao‘an District, Shenzhen, Guangdong, China Tel: +86—755 2523 4088 E—mail: agc@ageo—cert.com Service Hotline:400 089 2118

Report No.: AGC00703190601FE01 Page 13 of 28 LINE CONDUCTED EMISSION TEST-N RESULT: PASS

Report No.: AGC00703190601FE01 Page 14 of 28 9. RADIATED EMISSION TEST 9.1. LIMITS OF RADIATED EMISSION TEST Frequency Distance Maximum Field Strength Limit (MHz) (m) (dBuV/m/ Q.P.) 30~88 3 40.0 88~216 3 43.5 216~960 3 46.0 Above 960 3 54.0 Note: The lower limit shall apply at the transition frequency. 9.2. BLOCK DIAGRAM OF TEST SETUP System Diagram of Connections between EUT and Simulators

Report No.: AGC00703190601FE01 Page 15 of 28 9.3. PROCEDURE OF RADIATED EMISSION TEST (1) The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. When the EUT is a tabletop system, a wooden turntable with a height of 0.8 meters is used which is placed on the ground plane as per ANSI C63.4 (see Test Facility for the dimensions of the ground plane used). When the EUT is floor-standing equipment, it is placed on the ground plane which has a 3-12 mm non-conductive covering to insulate the EUT from the ground plane. (2) Support equipment, if needed, was placed as per ANSI C63.4. (3) All I/O cables were positioned to simulate typical actual usage as per ANSI C63.4. (4) The EUT received AC120V/60Hz power from socket under the turntable, if any. (5) The antenna was placed at 3 meter away from the EUT as stated in FCC Part 15. The antenna connected to the Analyzer via a cable and at times a pre-amplifier would be used. (6) The Analyzer / Receiver quickly scanned from 30MHz to 1000MHz. The EUT test program was started. Emissions were scanned and measured rotating the EUT to 360 degrees and positioning the antenna 1 to 4 meters above the ground plane, in both the vertical and the horizontal polarization, to maximize the emission reading level. (7) The test mode(s) were scanned during the test: (8) Recorded at least the six highest emissions. Emission frequency, amplitude, antenna position, polarization and turntable position were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit and Q.P./Peak reading is presented.

Report No.: AGC00703190601FE01 Page 16 of 28 9.4. TEST RESULT OF RADIATED EMISSION TEST Radiated Emission below 1GHz Test at 3m Distance-Horizontal

Report No.: AGC00703190601FE01 Page 17 of 28 Radiated Emission below 1GHz Test at 3m Distance-Vertical RESULT: PASS Note： Measurement(dBuV/m)=Reading(dBuV)+Factor(dB/m) Factor(dB/m)=Antenna Factor(dB/m)+Cable loss(dB)+Attenuation(dB)for Attenuator Over= Measurement -Limit Remark: which 1GHz-12.5GHz are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured.

Report No.: AGC00703190601FE01 Page 18 of 28 APPENDIX A: PHOTOGRAPHS OF TEST SETUP FCC CONDUCTED EMISSION TEST SETUP FCC RADIATED EMISSION TEST SETUP

Report No.: AGC00703190601FE01 Page 19 of 28 RADIATED EMISSION ABOVE 1G TEST SETUP

Report No.: AGC00703190601FE01 Page 20 of 28 APPENDIX B: PHOTOGRAPHS OF EUT ALL VIEW OF EUT TOP VIEW OF EUT

Report No.: AGC00703190601FE01 Page 21 of 28 BOTTOM VIEW OF EUT FRONT VIEW OF EUT

Report No.: AGC00703190601FE01 Page 22 of 28 BACK VIEW OF EUT LEFT VIEW OF EUT

Report No.: AGC00703190601FE01 Page 23 of 28 RIGHT VIEW OF EUT OPEN VIEW OF EUT

Report No.: AGC00703190601FE01 Page 24 of 28 INTERNAL VIEW OF EUT-1 INTERNAL VIEW OF EUT-2

Report No.: AGC00703190601FE01 Page 25 of 28 INTERNAL VIEW OF EUT-3 INTERNAL VIEW OF EUT-4

Report No.: AGC00703190601FE01 Page 26 of 28 INTERNAL VIEW OF EUT-5 INTERNAL VIEW OF EUT-6 WIFI Antenna

Report No.: AGC00703190601FE01 Page 27 of 28 INTERNAL VIEW OF EUT-7 INTERNAL VIEW OF EUT-8

Report No.: AGC00703190601FE01 Page 28 of 28 INTERNAL VIEW OF EUT-9 VIEW OF Battery ----END OF REPORT----


Document Created: 2019-07-17 02:37:00
Document Modified: 2019-07-17 02:37:00
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC