Test Report

FCC ID: 2AQPBBAP-0713B

Test Report

Download: PDF

FCCID_4099522

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AQPBBAP-0713B Report No.: LCS181025024AEA

FCC TEST REPORT
For
Boost Auto Parts LLC
remote
Test Model: BAP# 0713B
Additional Model No.: Please Refer to Page 6

Prepared for : Boost Auto Parts LLC
Boost Auto Parts 2948 Kirk Road.Suite 106, #324 Aurora Illinois,
Address :
UnitedStates 60502

Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd.
1/F., Xingyuan Industrial Park, Tongda Road, Bao’an Avenue,
Address :
Bao’an District, Shenzhen, Guangdong, China
Tel : (+86)755-82591330
Fax : (+86)755-82591332
Web : www.LCS-cert.com
Mail : webmaster@LCS-cert.com

Date of receipt of test sample : October 26, 2017
Number of tested samples : 1
Serial number : Prototype
Date of Test : October 26, 2017 ~ November 16, 2017
Date of Report : November 21, 2017

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 1 of 30

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AQPBBAP-0713B Report No.: LCS181025024AEA

FCC -- TEST REPORT

November 21, 2017
Test Report No. : LCS181025024AEA Date of issue

Test Mode............................... : BAP# 0713B

EUT......................................... : remote

Applicant............................... : Boost Auto Parts LLC
Boost Auto Parts 2948 Kirk Road.Suite 106, #324 Aurora Illinois,
Address.................................. :
UnitedStates 60502
Telephone............................... : /
Fax.......................................... : /

Manufacturer........................ : Wuxi Keyoung Electronic Technology Co., Ltd
5-301, 5-301 Huaqing Creative Park, Huishan Economic
Address................................... :
Development Zone, Wuxi, Jiangsu
Telephone............................... : /
Fax.......................................... : /

Factory................................... : Wuxi Keyoung Electronic Technology Co., Ltd
5-301, 5-301 Huaqing Creative Park, Huishan Economic
Address................................... :
Development Zone, Wuxi, Jiangsu
Telephone............................... : /
Fax.......................................... : /

Test Result Positive

The test report merely corresponds to the test sample.
It is not permitted to copy extracts of these test result without the written permission of the test laboratory.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 3 of 30

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AQPBBAP-0713B Report No.: LCS181025024AEA

Revision History

Revision Issue Date Revisions Revised By
00 November 21, 2017 Initial Issue Gavin Liang

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 4 of 30

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AQPBBAP-0713B Report No.: LCS181025024AEA

TABLE OF CONTENTS

1. GENERAL INFORMATION ................................................................................................................................... 6
1.1. DESCRIPTION OF DEVICE (EUT) ........................................................................................................................ 6
1.2. HOST SYSTEM CONFIGURATION LIST AND DETAILS .......................................................................................... 6
1.3. EXTERNAL I/O CABLE ......................................................................................................................................... 6
1.4. DESCRIPTION OF TEST FACILITY ........................................................................................................................ 6
1.5. STATEMENT OF THE MEASUREMENT UNCERTAINTY .......................................................................................... 7
1.6. MEASUREMENT UNCERTAINTY ........................................................................................................................... 7
1.7. DESCRIPTION OF TEST MODES .......................................................................................................................... 7
2. TEST METHODOLOGY ......................................................................................................................................... 8
2.1. EUT CONFIGURATION ........................................................................................................................................ 8
2.2. EUT EXERCISE ................................................................................................................................................... 8
2.3. GENERAL TEST PROCEDURES ........................................................................................................................... 8
3. SYSTEM TEST CONFIGURATION ...................................................................................................................... 9
3.1. JUSTIFICATION .................................................................................................................................................... 9
3.2. EUT EXERCISE SOFTWARE ................................................................................................................................ 9
3.3. SPECIAL ACCESSORIES ...................................................................................................................................... 9
3.4. BLOCK DIAGRAM/SCHEMATICS........................................................................................................................... 9
3.5. EQUIPMENT MODIFICATIONS .............................................................................................................................. 9
3.6. TEST SETUP ........................................................................................................................................................ 9
4. SUMMARY OF TEST RESULTS......................................................................................................................... 10
5. TEST ITEMS AND RESULTS .............................................................................................................................. 11
5.1. TRANSMISSION CEASE TIME ............................................................................................................................. 11
5.2. TRANSMITTER FIELD STRENGTH OF EMISSIONS .............................................................................................. 13
5.3. 99% AND 20DB BANDWIDTH EMISSIONS ......................................................................................................... 22
5.4. DUTY CYCLE ...................................................................................................................................................... 24
5.5. AC POWER LINE CONDUCTED EMISSIONS (NOT APPLICABLE) ....................................................................... 27
5.6. ANTENNA REQUIREMENT .................................................................................................................................. 28
6. LIST OF MEASURING EQUIPMENTS .............................................................................................................. 29
7. PHOTOGRAPHS OF TEST SETUP ................................................................................................................... 30
8. EXTERIOR PHOTOGRAPHS OF EUT .............................................................................................................. 30
9. INTERIOR PHOTOGRAPHS OF EUT ............................................................................................................... 30

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 5 of 30

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AQPBBAP-0713B Report No.: LCS181025024AEA

1. GENERAL INFORMATION

1.1. Description of Device (EUT)

EUT : remote
Test Model : BAP# 0713B
BAP# 0713, BAP# 0713R, BAP# 0713PL, BAP# 0713LG,
Additional Model No. :
BAP# 0713RLG, BAP# 0713RPL, BAP# 0713LGPL
PCB board, structure and internal of these model(s) are the
Model Declaration : same, So no additional models were tested.

Power Supply : DC3.0V from 2*AAA battery
Hardware version : 1.0
Software version : 1.0
Transmit Frequency : 315MHz
Number of Channels : 1

Modulation Type : FSK

Antenna Description : PCB Antenna, 5dBi (Max.)

1.2. Host System Configuration List and Details

Manufacturer Description Model Serial Number Certificate
-- -- -- --- --

1.3. External I/O Cable

I/O Port Description Quantity Cable
-- -- --

1.4. Description of Test Facility

FCC Registration Number. is 254912.
Industry Canada Registration Number. is 9642A-1.
ESMD Registration Number. is ARCB0108.
UL Registration Number. is 100571-492.
TUV SUD Registration Number. is SCN1081.
TUV RH Registration Number. is UA 50296516-001
NVLAP Registration Code is 600167-0

The 3m-Semi anechoic test site fulfils CISPR 16-1-4 according to ANSI C63.10:2013 and CISPR
16-1-4:2010 SVSWR requirement for radiated emission above 1GHz.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 6 of 30

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AQPBBAP-0713B Report No.: LCS181025024AEA

2. TEST METHODOLOGY

All measurements contained in this report were conducted with ANSI C63.10-2013, American National
Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices.
The radiated testing was performed at an antenna-to-EUT distance of 3 meters. All radiated and
conducted emissions measurement was performed at Shenzhen LCS Compliance Testing Laboratory Ltd.

2.1. EUT Configuration
The EUT configuration for testing is installed on RF field strength measurement to meet the Commissions
requirement and operating in a manner that intends to maximize its emission characteristics in a
continuous normal application.

2.2. EUT Exercise
The EUT was operated in the engineering mode to fix the TX frequency that was for the purpose of the
measurements.
According to its specifications, the EUT must comply with the requirements of the Section 15.203, 15.205,
15.207, 15.209 and 15.231 under the FCC Rules Part 15 Subpart C.

2.3. General Test Procedures

2.3.1 Conducted Emissions

The EUT is placed on the turntable, which is 0.8 m above ground plane. According to the requirements in
Section 6.2.1 of ANSI C63.10-2013 Conducted emissions from the EUT measured in the frequency range
between 0.15 MHz and 30MHz using Quasi-peak and average detector modes.

2.3.2 Radiated Emissions

The EUT is placed on a turn table, which is 0.8 m above ground plane. The turntable shall rotate 360
degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving
antenna, which varied from 1m to 4m to find out the highest emission. And also, each emission was to be
maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to find
out the maximum emissions, exploratory radiated emission measurements were made according to the
requirements in Section 6.3 of ANSI C63.10-2013.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 8 of 30

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AQPBBAP-0713B Report No.: LCS181025024AEA

3. SYSTEM TEST CONFIGURATION

3.1. Justification
The system was configured for testing in a continuous transmit condition.
Using sample to test, which was automatically launched

3.2. EUT Exercise Software
N/A
3.3. Special Accessories
N/A

3.4. Block Diagram/Schematics
Please refer to the related document

3.5. Equipment Modifications
Shenzhen LCS Compliance Testing Laboratory Ltd. has not done any modification on the EUT.

3.6. Test Setup
Please refer to the test setup photo.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 9 of 30

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AQPBBAP-0713B Report No.: LCS181025024AEA

4. SUMMARY OF TEST RESULTS

Applied Standard: FCC Part 15 Subpart C
FCC Rules Description of Test Result
§15.203 Antenna Requirement Compliant
§15.205 Restricted Bands Of Operation Compliant
§15.207 AC Mains Conducted Emission N/A*
§15.209 Radiated Emission Limits, General Requirements. Compliant
§15.231 (b) Field Strength Of Fundamental And Harmonics Compliant
§15.231 (c) 99% and 20dB Bandwidth Compliant
§15.231 (a)(1) Transmission Cease Time Compliant

Note:
1. All buttons have been taken into consideration and only worst case reported.
2. N/A – Not Applicable!!!

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 10 of 30

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AQPBBAP-0713B Report No.: LCS181025024AEA

5.2. Transmitter Field Strength of Emissions

5.2.1. Limit

According to § 15.231 (b), In addition to the provisions of §15.205, the field strength of emissions from
intentional radiators operated under this section shall not exceed the following:

Field strength of fundamental Field strength of spurious
Fundamental frequency (MHz)
(microvolts/meter) emissions (microvolts/meter)
40.66-40.70 2,250 225
71-130 1,250 125
130-174 11,250 to 3,750 1125 to 375
174-260 3,750 375
260-470 13,750 to 12,500 1375 to 1,250
Above 470 1 12,500 1,250
1
Linear interpolations.
(1) The above field strength limits are specified at a distance of 3 meters. The tighter limits apply at the
band edges.
(2) Intentional radiators operating under the provisions of this section shall demonstrate compliance with
the limits on the field strength of emissions, as shown in the above table, based on the average value of
the measured emissions. As an alternative, compliance with the limits in the above table may be based on
the use of measurement instrumentation with a CISPR quasi-peak detector. The specific method of
measurement employed shall be specified in the application for equipment authorization. If average
emission measurements are employed, the provisions in §15.35 for averaging pulsed emissions and for
limiting peak emissions apply. Further, compliance with the provisions of §15.205 shall be demonstrated
using the measurement instrumentation specified in that section.
(3) The limits on the field strength of the spurious emissions in the above table are based on the
fundamental frequency of the intentional radiator. Spurious emissions shall be attenuated to the average
(or, alternatively, CISPR quasi-peak) limits shown in this table or to the general limits shown in §15.209,
whichever limit permits a higher field strength.

Frequencies(MHz) Field Strength (microvolts/meter) Measurement Distance (meters)
0.009~0.490 2400/F(KHz) 300
0.490~1.705 24000/F(KHz) 30
1.705~30.0 30 30
30~88 100 3
88~216 150 3
216~960 200 3
Above 960 500 3

According to § 15.231 (e), Intentional radiators may operate at a periodic rate exceeding that specified in
paragraph (a) of this section and may be employed for any type of operation, including operation
prohibited in paragraph (a) of this section, provided the intentional radiator complies with the provisions of
paragraphs (b) through (d) of this section, except the field strength table in paragraph (b) of this section is
replaced by the following:

Field strength of fundamental Field strength of spurious
Fundamental frequency (MHz)
(microvolts/meter) emissions (microvolts/meter)
40.66-40.70 1,000 100
71-130 500 50
130-174 500 to 1,5001 50 to 1501
174-260 1,500 150
260-470 1,500 to 5,0001 150 to 5001
Above 470 5,000 500

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 13 of 30

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AQPBBAP-0713B Report No.: LCS181025024AEA

5.2.2 Measuring Instruments and Setting

Please refer to equipment’s list in this report. The following table is the setting of spectrum analyzer and
receiver.

Spectrum Parameter Setting
Attenuation Auto
Start Frequency 1000 MHz
Stop Frequency 10th carrier harmonic
RB / VB (Emission in restricted band) 1MHz / 3MHz for Peak, 1 MHz / 10Hz for Average
RB / VB (Emission in non-restricted band) 1MHz / 3MHz for Peak, 1 MHz / 10Hz for Average

Receiver Parameter Setting
Attenuation Auto
Start ~ Stop Frequency 9kHz~150kHz / RB/VB 200Hz/1KHz for QP/Average
Start ~ Stop Frequency 150kHz~30MHz / RB/VB 9kHz/30KHz for QP/Average
Start ~ Stop Frequency 30MHz~1000MHz / RB/VB 120kHz/1MHz for QP

5.2.3. Test Procedures

1) Sequence of testing 9 kHz to 30 MHz
Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or described by
manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 0.8 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions.
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.
Premeasurement:
--- The turntable rotates from 0° to 315° using 45° steps.
--- The antenna height is 1.5 meter.
--- At each turntable position the analyzer sweeps with peak detection to find the maximum of all
emissions
Final measurement:
--- Identified emissions during the premeasurement the software maximizes by rotating the turntable
position (0° to 360°) and by rotating the elevation axes (0° to 360°).
--- The final measurement will be done in the position (turntable and elevation) causing the highest
emissions with QPK detector.
--- The final levels, frequency, measuring time, bandwidth, turntable position, correction factor, margin to
the limit and limit will be recorded. Also a plot with the graph of the premeasurement and the limit will be
stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 14 of 30

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AQPBBAP-0713B Report No.: LCS181025024AEA

2) Sequence of testing 30 MHz to 1 GHz

Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or described by
manufacturer.
--- If the EUT is a tabletop system, a table with 0.8 m height is used, which is placed on the ground plane.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.
Premeasurement:
--- The turntable rotates from 0° to 315° using 45° steps.
--- The antenna is polarized vertical and horizontal.
--- The antenna height changes from 1 to 3 meter.
--- At each turntable position, antenna polarization and height the analyzer sweeps three times in peak to
find the maximum of all emissions.
Final measurement:
--- The final measurement will be performed with minimum the six highest peaks.
--- According to the maximum antenna and turntable positions of premeasurement the software maximize
the peaks by changing turntable position (± 45°) and antenna movement between 1 and 4 meter.
--- The final measurement will be done with QP detector with an EMI receiver.
--- The final levels, frequency, measuring time, bandwidth, antenna height, antenna polarization, turntable
angle, correction factor, margin to the limit and limit will be recorded. Also a plot with the graph of the
premeasurement with marked maximum final measurements and the limit will be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 15 of 30

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AQPBBAP-0713B Report No.: LCS181025024AEA

3) Sequence of testing 1 GHz to 18 GHz

Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or described by
manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 1.5 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.
Premeasurement:
--- The turntable rotates from 0° to 315° using 45° steps.
--- The antenna is polarized vertical and horizontal.
--- The antenna height is 1.5 meter.
--- At each turntable position and antenna polarization the analyzer sweeps with peak detection to find the
maximum of all emissions.
Final measurement:
--- The final measurement will be performed with minimum the six highest peaks.
--- According to the maximum found antenna polarization and turntable position of the premeasurement
the software maximizes the peaks by rotating the turntable position (0° to 360°). This measurement is
repeated for different EUT-table positions (0° to 150° in 30°-steps). This procedure is repeated for both
antenna polarizations.
--- The final measurement will be done in the position (turntable, EUT-table and antenna polarization)
causing the highest emissions with Peak and RMS detector.
--- The final levels, frequency, measuring time, bandwidth, turntable position, EUT-table position, antenna
polarization, correction factor, margin to the limit and limit will be recorded. Also a plot with the graph of
the premeasurement with marked maximum final measurements and the limit will be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 16 of 30

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AQPBBAP-0713B Report No.: LCS181025024AEA

4) Sequence of testing above 18 GHz

Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or described by
manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 1.5 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 1 meter.
--- The EUT was set into operation.
Premeasurement:
--- The antenna is moved spherical over the EUT in different polarizations of the antenna.
Final measurement:
--- The final measurement will be performed at the position and antenna orientation for all detected
emissions that were found during the premeasurements with Peak and RMS detector.
--- The final levels, frequency, measuring time, bandwidth, correction factor, margin to the limit and limit
will be recorded. Also a plot with the graph of the premeasurement and the limit will be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 17 of 30

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AQPBBAP-0713B Report No.: LCS181025024AEA

5.2.8. Results of Radiated Emissions (Above1GHz)

Temperature 25.1℃ Humidity 53.1%
Harmonics Emissions/
Test Engineer MINA XU Configurations
Spurious Emission

Peak Value
Frequency
Level (dBuV/m) Limit Line (dBuV/m) Margin (dB) Polarization
(MHz)
1259.94 45.41 74.00 -28.59 Horizontal
1575.05 46.49 74.00 -27.51 Horizontal
1890.14 47.06 74.00 -26.94 Horizontal
1259.93 47.11 74.00 -26.89 Vertical
1575.06 46.77 74.00 -27.23 Vertical
1890.10 47.28 74.00 -26.72 Vertical

Average Value:
Peak Duty Average
Frequency Limit Line
Level cycle value Margin (dB) Polarization
(MHz) (dBuV/m)
(dBuV/m) factor (dBuV/m)
1259.88 45.44 -13.13 32.31 54.00 -21.69 Horizontal
1575.06 46.50 -13.13 33.37 54.00 -20.63 Horizontal
1890.13 47.05 -13.13 33.92 54.00 -20.08 Horizontal
1259.92 47.11 -13.13 33.98 54.00 -20.02 Vertical
1575.07 46.77 -13.13 33.64 54.00 -20.36 Vertical
1890.14 47.29 -13.13 34.16 54.00 -19.84 Vertical

Remark:

1. Measuring frequencies from 9 KHz~10th harmonic (ex. 5GHz), No emission found between lowest internal
used/generated frequency to 30MHz.
2. Radiated emissions measured in frequency range from 9 KHz~10th harmonic (ex. 5GHz) were made with an
instrument using Peak detector mode.
3. Average values = Peak values + DC factor = Peak values – 13.13
3. Data of measurement within this frequency range shown “---” in the table above means the reading of
emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be
measured.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 21 of 30

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AQPBBAP-0713B Report No.: LCS181025024AEA

7. PHOTOGRAPHS OF TEST SETUP

Please refer to separated files for Test Setup Photos of the EUT.

8. EXTERIOR PHOTOGRAPHS OF EUT

Please refer to separated files for External Photos of the EUT.

9. INTERIOR PHOTOGRAPHS OF EUT

Please refer to separated files for Internal Photos of the EUT.

----------------THE END OF TEST REPORT---------------

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 30 of 30

Document Created: 2018-12-07 00:07:54
Document Modified: 2018-12-07 00:07:54

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC