14_H5053 TestRpt DSC r1

FCC ID: 2AQA6-H5053

Test Report

Download: PDF
FCCID_4459130

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 1 of 31 FCC Test Report Client Name : Shenzhen Intellirocks Tech. Co., Ltd. Room 401 Building 9, YunGu phase II, Nanshan, Liuxian Avenue, Address : Taoyuan Street, Nanshan District, Shenzhen, China Product Name : Outdoor Temperature Humidity Monitor Date : Sept. 24, 2019 Shenzhen Anbotek Compliance Laboratory Limited Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 2 of 31 Contents 1. General Information...............................................................................................................................................4 1.1. Client Information....................................................................................................................................... 4 1.2. Description of Device (EUT).....................................................................................................................4 1.3. Auxiliary Equipment Used During Test................................................................................................... 4 1.4. Description of Test Modes........................................................................................................................ 5 1.5. List of channels...........................................................................................................................................5 1.6. Description Of Test Setup......................................................................................................................... 6 1.7. Test Equipment List....................................................................................................................................7 1.8. Measurement Uncertainty.........................................................................................................................8 1.9. Description of Test Facility........................................................................................................................ 8 2. Summary of Test Results..................................................................................................................................... 9 3. Conducted Emission Test...................................................................................................................................10 3.1. Test Standard and Limit.......................................................................................................................... 10 3.2. Test Setup..................................................................................................................................................10 3.3. Test Procedure..........................................................................................................................................10 3.4. Test Data....................................................................................................................................................10 4. Radiation Spurious Emission and Band Edge................................................................................................11 4.1. Test Standard and Limit.......................................................................................................................... 11 4.2. Test Setup..................................................................................................................................................12 4.3. Test Procedure..........................................................................................................................................13 4.4. Test Data....................................................................................................................................................13 5. 20DB Occupy Bandwidth Test........................................................................................................................... 20 5.1. Test Standard and Limit.......................................................................................................................... 20 5.2. Test Setup..................................................................................................................................................20 5.3. Test Procedure..........................................................................................................................................20 5.4. Test Data....................................................................................................................................................20 6. Dwell Time Test.................................................................................................................................................... 22 6.1. Test Standard and Limit.......................................................................................................................... 22 6.2. Test Setup..................................................................................................................................................22 6.3. Test Procedure..........................................................................................................................................22 6.4. Test Data....................................................................................................................................................22 7. Antenna Requirement......................................................................................................................................... 24 7.1. Test Standard and Requirement............................................................................................................24 7.2. Antenna Connected Construction..........................................................................................................24 APPENDIX I -- TEST SETUP PHOTOGRAPH...................................................................................................25 APPENDIX II -- EXTERNAL PHOTOGRAPH..................................................................................................... 26 APPENDIX III -- INTERNAL PHOTOGRAPH..................................................................................................... 29 Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 3 of 31 TEST REPORT Applicant : Shenzhen Intellirocks Tech. Co., Ltd. Manufacturer : Shenzhen Intellirocks Tech. Co., Ltd. Product Name : Outdoor Temperature Humidity Monitor Model No. : H5053 Trade Mark : N.A. Rating(s) : Input: DC 3V by "AAA"*2 battery inside Test Standard(s) : FCC Part15 Subpart C 2018, Section 15.231 Test Method(s) : ANSI C63.10: 2013 The device described above is tested by Shenzhen Anbotek Compliance Laboratory Limited to determine the maximum emission levels emanating from the device and the severe levels of the device can endure and its performance criterion. The measurement results are contained in this test report and Shenzhen Anbotek Compliance Laboratory Limited is assumed full of responsibility for the accuracy and completeness of these measurements. Also, this report shows that the EUT (Equipment Under Test) is technically compliant with the FCC Part 15 Subpart C requirements. This report applies to above tested sample only and shall not be reproduced in part without written approval of Shenzhen Anbotek Compliance Laboratory Limited. Date of Receipt Sept. 04, 2019 Date of Test Sept. 04~21, 2019 Prepared By (Engineer / Dolly Mo) Reviewer (Supervisor / Bibo Zhang) Approved & Authorized Signer (Manager / Sally Zhang) Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 4 of 31 1. General Information 1.1. Client Information Applicant : Shenzhen Intellirocks Tech. Co., Ltd. Room 401 Building 9, YunGu phase II, Nanshan, Liuxian Avenue, Taoyuan Address : Street, Nanshan District, Shenzhen, China Manufacturer : Shenzhen Intellirocks Tech. Co., Ltd. Room 401 Building 9, YunGu phase II, Nanshan, Liuxian Avenue, Taoyuan Address : Street, Nanshan District, Shenzhen, China Factory : Shenzhen Intellirocks Tech. Co., Ltd. Room 401 Building 9, YunGu phase II, Nanshan, Liuxian Avenue, Taoyuan Address : Street, Nanshan District, Shenzhen, China 1.2. Description of Device (EUT) Product Name : Outdoor Temperature Humidity Monitor Model No. : H5053 Trade Mark : N.A. Test Power Supply : DC 3V Battery inside Operation Frequency: 433.92MHz Number of Channel: 1 Channels Product : Modulation Type: FSK Description Antenna Type: Spring Antenna Antenna Gain(Peak): 0 dBi Remark: 1) For a more detailed features description, please refer to the manufacturer’s specifications or the User’s Manual. 1.3. Auxiliary Equipment Used During Test N/A Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 5 of 31 1.4. Description of Test Modes To investigate the maximum EMI emission characteristics generates from EUT, the test system was pre-scanning tested base on the consideration of following EUT operation mode or test configuration mode which possible have effect on EMI emission level. Each of these EUT operation mode(s) or test configuration mode(s) mentioned above was evaluated respectively. Pretest Mode Description Mode 1 TX Mode For Radiated Emission Final Test Mode Description Mode 1 TX Mode Note: During the test, the EUT was keeping continuous transmission. 1.5. List of channels Freq. Note Channel (MHz) (Modulation Type) 01 433.92 FSK Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 6 of 31 1.6. Description Of Test Setup RE E-1 0.8m EUT Table 1.5m Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 7 of 31 1.7. Test Equipment List Cal. Item Equipment Manufacturer Model No. Serial No. Last Cal. Interval L.I.S.N. 1. Artificial Mains Rohde & Schwarz ENV216 100055 Nov. 26, 2018 1 Year Network 2. EMI Test Receiver Rohde & Schwarz ESPI3 101604 Nov. 05, 2018 1 Year Compliance 3. RF Switching Unit RSU-M2 38303 Nov. 05, 2018 1 Year Direction 4. Spectrum Analysis Agilent E4407B US39390582 Nov. 05, 2018 1 Year MAX Spectrum 5. Agilent N9020A MY51170037 Nov. 05, 2018 1 Year Analysis BK1G18G30 6. Preamplifier SKET Electronic KD17503 Nov. 05, 2018 1 Year D Double Ridged Horn Instruments 7. GTH-0118 351600 Nov. 20, 2018 1 Year Antenna corporation Bilog Broadband 8. Schwarzbeck VULB9163 VULB 9163-289 Nov. 19, 2018 1 Year Antenna 9. Loop Antenna Schwarzbeck FMZB1519B 00053 Nov. 20, 2018 1 Year LB-180400-K 10. Horn Antenna A-INFO J211060628 Nov. 20, 2018 1 Year F 11. Pre-amplifier SONOMA 310N 186860 Nov. 05, 2018 1 Year EMI Test Software 12. SHURPLE N/A N/A N/A N/A EZ-EMC RF Test Control 13. YIHENG YH3000 2017430 Nov. 05, 2018 1 Year System 14. Power Sensor DAER RPR3006W 15I00041SN045 Nov. 05, 2018 1 Year 15. Power Sensor DAER RPR3006W 15I00041SN046 Nov. 05, 2018 1 Year MXA Spectrum 16. Agilent N9020A MY51170037 Nov. 05, 2018 1 Year Analysis MXG RF Vector 17. Agilent N5182A MY48180656 Nov. 05, 2018 1 Year Signal Generator 18. Signal Generator Agilent E4421B MY41000743 Nov. 05, 2018 1 Year 19. DC Power Supply LW TPR-6420D 374470 Oct. 31, 2018 1 Year Constant ZJ-KHWS80 20. Temperature ZHONGJIAN N/A Nov. 01, 2018 1 Year B Humidity Chamber Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 8 of 31 1.8. Measurement Uncertainty Radiation Uncertainty : Ur = 3.9 dB (Horizontal) Ur = 3.8 dB (Vertical) Conduction Uncertainty : Uc = 3.4 dB 1.9. Description of Test Facility The test facility is recognized, certified, or accredited by the following organizations: FCC-Registration No.: 184111 Shenzhen Anbotek Compliance Laboratory Limited, EMC Laboratory has been registed and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration No. 184111, September 30, 2018. ISED-Registration No.: 8058A Shenzhen Anbotek Compliance Laboratory Limited, EMC Laboratory has been registered and fully described in a report filed with the (ISED) Innovation, Science and Economic Development Canada. The acceptance letter from the ISED is maintained in our files. Registration 8058A, March 07, 2019. Test Location Shenzhen Anbotek Compliance Laboratory Limited. 1/F, Building D, Sogood Science and Technology Park, Sanwei community, Hangcheng Street, Bao'an District, Shenzhen, Guangdong, China.518102 Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 9 of 31 2. Summary of Test Results Standard Section Test Item Result 15.203 Antenna Requirement PASS 15.207 Conducted Emission N/A 15.205/15.209/15.231(b) Spurious Emission PASS 15.231(c) 20dB Occupied Bandwidth PASS 15.231(a) Dwell time PASS Remark: “N/A” is an abbreviation for Not Applicable. Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 10 of 31 3. Conducted Emission Test 3.1. Test Standard and Limit Test Standard FCC Part15 Section 15.207 Maximum RF Line Voltage (dBuV) Frequency Quasi-peak Level Average Level Test Limit 150kHz~500kHz 66 ~ 56 * 56 ~ 46 * 500kHz~5MHz 56 46 5MHz~30MHz 60 50 Remark: (1) *Decreasing linearly with logarithm of the frequency. (2) The lower limit shall apply at the transition frequency. 3.2. Test Setup 3.3. Test Procedure The EUT system is connected to the power mains through a line impedance stabilization network (L.I.S.N.). This provides a 50ohm coupling impedance for the EUT system. Please refer the block diagram of the test setup and photographs. Both sides of AC line are checked to find out the maximum conducted emission. In order to find the maximum emission levels, the relative positions of equipment and all of the interface cables shall be changed according to FCC ANSI C63.10-2013 on Conducted Emission Measurement. The bandwidth of test receiver (ESCI) set at 9kHz. The frequency range from 150kHz to 30MHz is checked. 3.4. Test Data There is DC 3V Battery inside, So there is no need to test. Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 11 of 31 4. Radiation Spurious Emission and Band Edge 4.1. Test Standard and Limit Test Standard FCC Part15 C Section 15.209, 15.205 and 15.231(b) Frequency Field strength Limit Measurement Remark (MHz) (microvolt/meter) (dBuV/m) distance (m) 0.009MHz~0.490MHz 2400/F(kHz) - - 300 0.490MHz-1.705MHz 24000/F(kHz) - - 30 1.705MHz-30MHz 30 - - 30 Test Limit 30MHz~88MHz 100 40.0 Quasi-peak 3 88MHz~216MHz 150 43.5 Quasi-peak 3 216MHz~960MHz 200 46.0 Quasi-peak 3 960MHz~1000MHz 500 54.0 Quasi-peak 3 500 54.0 Average 3 Above 1000MHz - 74.0 Peak 3 Remark: (1)The lower limit shall apply at the transition frequency. (2) 15.35(b), Unless otherwise specified, the limit on peak radio frequency emissions is 20dB above the maximum permitted average emission limit applicable to the equipment under test. This peak limit applies to the total peak emission level radiated by the device. the formulas for calculating the maximum permitted fundamental field strengths are as follows: for the band 260-470 MHz, μV/m at 3 meters = 41.6667(F) - 7083.3333. The maximum permitted unwanted emission level is 20 dB below the maximum permitted fundamental level Emission Level (dBuV/m)=20log Emission Level(uV/m) The field strength of emission limits have been calculated in below table: Fundamental Frequency Field Strength of Fundamental (MHz) (dBuV/m)@3m 433.92 80.82 (AVG) 433.92 100.82 (Peak) Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 12 of 31 4.2. Test Setup Figure 1. Below 30MHz Figure 2. 30MHz to 1GHz Figure 3. Above 1 GHz Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 13 of 31 4.3. Test Procedure For below 1GHz: The EUT is placed on a turntable, which is 0.8m above the ground plane. For above 1GHz: The EUT is placed on a turntable, which is 1.5m above the ground plane. The turn table can rotate 360 degrees to determine the position of the maximum emission level. The EUT is set 3 meters away from the receiving antenna which is mounted on a antenna tower. The antenna can be moved up and down from 1 to 4 meters to find out the maximum emission level. Rotated the EUT through three orthogonal axes to determine the maximum emissions, both horizontal and vertical polarization of the antenna are set on test. The EUT is tested in 9*6*6 Chamber. The device is evaluated in xyz orientation. For 9kHz to 150kHz, Set the spectrum analyzer as: RBW = 200Hz, VBW =1kHz, Detector= Quasi-Peak, Trace mode= Max hold, Sweep- auto couple. For 150kHz to 30MHz, Set the spectrum analyzer as: RBW = 9KHz, VBW =30kHz, Detector= Quasi-Peak, Trace mode= Max hold, Sweep- auto couple. For 30MHz to 1000MHz, Set the spectrum analyzer as: RBW = 100kHz, VBW =300kHz,Detector= Quasi-Peak, Trace mode= Max hold, Sweep- auto couple. For above 1GHz,Set the spectrum analyzer as: RBW =1MHz, VBW =1MHz, Detector= Peak, Trace mode= Max hold, Sweep- auto couple. RBW =1MHz, VBW =10Hz, Detector= Average, Trace mode= Max hold, Sweep- auto couple. 4.4. Test Data PASS During the test, Pre-scan all kind of the place mode (X-axis, Y-axis, Z-axis), and found the X-axis is the worst case. The test results of 9kHz-30MHz and above 18000MHz are attenuated more than 20dB below the permissible limits, so the results don't record in the report. Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 14 of 31 Test Results (Fundamental 433.92MHz) Duty Cable Ant Frequency Antenna Reading Amplifier cycle Results Limits Det. Loss Factor Factor (MHz) Pol. (dBuV/m) (dB) (dB) (dB) (dB) (dBuV/m) (dBuV/m) Mode 433.92 H 94.02 1.52 12.64 31.45 - 76.73 100.82 PK 433.92 H 94.02 1.52 12.64 31.45 -12.83 63.90 80.82 AV 433.92 V 97.16 1.52 12.64 31.45 - 79.87 100.82 PK 433.92 V 97.16 1.52 12.64 31.45 -12.83 67.04 80.82 AV Remark: 1. Result = Reading + Cable Loss +Ant Factor –Amplifier + Duty cycle Factor 2. Pulse Desensitization Correction Factor Pulse Width (PW)= 0.280ms 2/PW=2/0.280=7.14kHz RBW(1000kHz)＞ 2/PW (7.14KHz) Therefore PDCF is not needed. 3. Duty Cycle Factor Calculate Formula: AV=PEAK +Duty Cycle Factor Duty Cycle Factor=20log(Duty Cycle) Duty Cycle= on time/ period Test Data: T on time=0.280ms*19+1.080ms*6=11.80 ms T period=51.70ms Duty Cycle=22.82% Duty Cycle Factor =20log(Duty Cycle)=-12.83 Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 15 of 31 T on time slot-1 T on time slot-2 T period Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 16 of 31 Test Results (Harmonics Emissions) Duty Cable Ant Frequency Antenna Reading Amplifier cycle Results Limits Det Loss Factor Factor (MHz) Pol. (dBuV/m) (dB) (dB) (dB) (dB) (dBuV/m) (dBuV/m) Mode 867.84 H 74.37 1.92 12.71 31.72 - 57.28 80.82 PK 867.84 H 74.37 1.92 12.71 31.72 -12.83 44.45 60.82 AV 867.84 V 76.16 1.92 12.71 31.72 - 59.07 80.82 PK 867.84 V 76.16 1.92 12.71 31.72 -12.83 46.24 60.82 AV 1301.76 H 63.47 2.38 21.43 32.45 - 54.83 74 PK 1301.76 H 63.47 2.38 21.43 32.45 -12.83 42.00 54 AV 1301.76 V 65.98 2.38 18.56 32.45 - 54.47 74 PK 1301.76 V 65.98 2.38 18.56 32.45 -12.83 41.64 54 AV Remark : 1. Result = Reading + Cable Loss +Ant Factor –Amplifier + Duty cycle Factor 2. Pulse Desensitization Correction Factor Pulse Width (PW)= 0.280ms 2/PW=2/0.280=7.14kHz RBW(1000kHz)＞ 2/PW (7.14KHz) Therefore PDCF is not needed. 3. Duty Cycle Factor=-8.44 Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 17 of 31 Test Results (Radiated Emission) Cable Ant Frequency Antenna Reading Amplifier Results Limits Margin Det. Loss Factor (MHz) Pol. (dBuV/m) (dB) (dB) (dB) (dBuV/m) (dBuV/m) (dB) Mode 54.41 H 56.49 1.03 11.15 40.74 27.93 40.0 -12.07 QP 127.02 H 59.13 1.24 12.24 40.48 32.13 43.5 -11.37 QP 732.78 H 61.91 1.67 13.75 41.27 36.06 46.0 -9.94 QP 54.41 V 55.64 1.03 11.15 40.74 27.08 40.0 -12.92 QP 127.02 V 60.51 1.24 12.24 40.48 33.51 43.5 -9.99 QP 732.78 V 62.56 1.67 13.75 41.27 36.71 46.0 -9.29 QP Remark: 1. Results = Reading + Cable Loss +Ant Factor –Amplifier Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 18 of 31 Test Results (30~1000MHz) Job No.: SZAWW190904006-01 Temp.(℃)/Hum.(%RH): 23.1℃/50%RH Standard: FCC PART 15C Power Source: DC 3V Battery inside Test Mode: TX Mode Polarization: Horizontal Note: Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 19 of 31 Test Results (30~1000MHz) Job No.: SZAWW190904006-01 Temp.(℃)/Hum.(%RH): 23.1℃/50%RH Standard: FCC PART 15C Power Source: DC 3V Battery inside Test Mode: TX Mode Polarization: Vertical Note: Remark: 1. Results = Reading + Cable Loss +Ant Factor –Amplifier Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 20 of 31 5. 20DB Occupy Bandwidth Test 5.1. Test Standard and Limit Test Standard FCC Part15 C Section 15.231 (c) According to FCC Part 15.231(c), The bandwidth of the emission shall be no wider than 0.25% of the center frequency for devices operating above 70MHz and below 900MHz. For devices operating above 900MHz, the emission shall be no wider than 0.5% of the center frequency. Bandwidth is determined at the points 20dB down from the modulated carrier. Test Limit So the emission bandwidth limits have been calculated in below table: Fundamental Limit of 20dB Bandwidth Frequency 433.92 MHz 433920x0.0025=1084.80 kHz 5.2. Test Setup 5.3. Test Procedure 1. Place the EUT on the table and set it in the continuously transmitting mode. 2. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 3. Set the spectrum analyzer as: RBW = 100kHz, VBW≥3*RBW =300kHz, Span= 2MHz Detector= Peak Trace mode= Max hold. Sweep- auto couple. 4. Mark the peak frequency and –20dB (upper and lower) frequency. 5. Repeat until all the rest channels are investigated. 5.4. Test Data Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 21 of 31 Test Item : 20dB Bandwidth Test Mode : Continuously transmitting Test Voltage : DC 3V Battery inside Temperature : 24℃ Test Result : PASS Humidity : 55%RH Freq. Limit Modulation Type Bandwidth (kHz) Results (MHz) (kHz) 433.92 FSK 124.5 <1084.80 PASS 433.92MHz Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 22 of 31 6. Dwell Time Test 6.1. Test Standard and Limit Test Standard FCC Part 15.231(a)(1) According to FCC Part 15.231(a)(1), A manually operated transmitter shall Test Limit employ a switch that will automatically deactivate the transmitter within not more than 5 seconds of being released 6.2. Test Setup 6.3. Test Procedure 1. Place the EUT on the table and set it in continuously transmitting mode. Remove the antenna from the EUT and then connect a low loss RF cable from the antenna port to the spectrum analyzer. 2. Set the spectrum analyzer as RBW=1000kHz, VBW= 1000 kHz, Span= 0Hz, Sweep Time= 20 Seconds. 3. Record the Delta mark time. 6.4. Test Data Test Item : Dwell Time Test Mode : Continuously transmitting Test Voltage : DC 3V Battery inside Temperature : 24℃ Test Result : PASS Humidity : 55%RH Test Mode Transmitting time(s) Limit(s) Result FSK mode 0.039 ≤5 PASS Please refer the following plot. Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 23 of 31 Dwell Time Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 24 of 31 7. Antenna Requirement 7.1. Test Standard and Requirement Test Standard FCC Part15 Section 15.203 1) 15.203 requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. Antenna requirement must meet at least one of the following: Requirement 1) Antenna must be permanently attached to device. 2) The antenna must use a unique type of connector to attach to the device. 3) Device must be professionally installed. The installer shall be responsible for ensuring that the correct antenna is employed by the device. 7.2. Antenna Connected Construction The antenna is a Spring antenna which permanently attached, and the best case gain of the antenna is 0 dBi. It complies with the standard requirement. Antenna Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 25 of 31 APPENDIX I -- TEST SETUP PHOTOGRAPH Photo of Radiated Emission Measurement Code:AB-RF-05-a

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 26 of 31 APPENDIX II -- EXTERNAL PHOTOGRAPH Code:AB-RF-05-a

e ltE \‘J‘\\\l\\\\\\\ m 'N Wi\gWWW

Anbotek Product Safety \ lih ks ji Shenzhen Anbotek Compliance Laboratory Limited ddddddd : 1/F., Building D, Sogood Science and Technology Park, Sanwei Community @ Hotline Hangcheng Street, Bac‘an District , Shenzhen , Guangdong, China 2 400—003—0500 Tel:(86) 75526066440 Fax : (86) 755—26014772 Email: service @anbotek.:co www.anbotek.com

Report No.: SZAWW190904006-01 FCC ID: 2AQA6-H5053 Page 29 of 31 APPENDIX III -- INTERNAL PHOTOGRAPH Code:AB-RF-05-a

Anbotek Product Safety 6 5 4 3 c 2 SMDOH 1 l'|131NI &l O,,,.'1!1,('211;3“Pfl'” 5u| rLlII 0 7 16 dn l Shenzhen Anbotek Compliance Laboratory Limited Address:1/F., Building D, Sogood Science and Technology Park, Sanwei Community, @ Hotline Hangcheng Street, Bac‘an.District, Shenzhen, Guangdong, China. °/ 400—003—0500 Tel:(86) 755—26066440 Fax (86) 755—26014772 Email: service @anbotek.com www.anbotek.com

Anbotek Product Safety Shenzhen Anbotek Compliance Laboratory Limited Address: 1/F., Building D, Sogood Science and Technology Park, Sanwei Community, @ Hotline Hangcheng Street, Bac‘an.District, Shenzhen, Guangdong, China. 400—003—0500 Tel:(86) 755—26066440 Fax: (86) 755—26014772 Email: service@anbotek.com www.anbotek.com


Document Created: 2019-09-27 00:41:09
Document Modified: 2019-09-27 00:41:09
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC