BSL12139801RF

FCC ID: 2APU9-391

Test Report

Download: PDF
FCCID_4234984

BSL Testing Co.,LTD. Report No.: BSL12139801RF FCC Part 15C Measurement and Test Report For Shenzhen Hanrongda Electronic Co.,Ltd FCC ID: 2APU9-391 FCC Rule(s): FCC Part 15.247 Product Description: FM headphone with bluetooth Tested Model: HRD-391 Report No.: BSL12139801RF Tested Date: January 23-25, 2019 Issued Date: January 30, 2019 Tested By: Messi Wang / Engineer Reviewed By: Lisa. Li / EMC Manager Approved & Authorized By: Mike mo / PSQ Manager Prepared By: BSL Testing Co.,LTD. NO. 24, ZH Park, Nantou, Shenzhen, 518000 China Tel: 400-882-9628 Fax: 86- 755-26508703 Report No.: BSL12139801RF Page 1 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF TABLE OF CONTENTS 1. GENERAL INFORMATION.................................................................................................................................... 3 1.1 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT).............................................................................. 3 1.2 TEST STANDARDS................................................................................................................................................... 4 1.3 TEST METHODOLOGY............................................................................................................................................. 4 1.4 TEST FACILITY........................................................................................................................................................ 4 1.5 EUT SETUP AND TEST MODE................................................................................................................................. 5 1.6 MEASUREMENT UNCERTAINTY...............................................................................................................................5 1.7 TEST EQUIPMENT LIST AND DETAILS..................................................................................................................... 6 2. SUMMARY OF TEST RESULTS............................................................................................................................ 7 3. RF EXPOSURE.......................................................................................................................................................... 8 3.1 STANDARD APPLICABLE......................................................................................................................................... 8 3.2 TEST RESULT.......................................................................................................................................................... 8 4. ANTENNA REQUIREMENT................................................................................................................................... 9 4.1 STANDARD APPLICABLE......................................................................................................................................... 9 4.2 EVALUATION INFORMATION................................................................................................................................... 9 5. POWER SPECTRAL DENSITY............................................................................................................................ 10 5.1 STANDARD APPLICABLE....................................................................................................................................... 10 5.2 TEST PROCEDURE..................................................................................................................................................10 5.3 ENVIRONMENTAL CONDITIONS.............................................................................................................................10 5.4 SUMMARY OF TEST RESULTS/PLOTS.................................................................................................................... 10 6. 6DB BANDWIDTH.................................................................................................................................................. 13 6.1 STANDARD APPLICABLE....................................................................................................................................... 13 6.2 TEST PROCEDURE..................................................................................................................................................13 6.3 ENVIRONMENTAL CONDITIONS.............................................................................................................................13 6.4 SUMMARY OF TEST RESULTS/PLOTS.................................................................................................................... 13 7. RF OUTPUT POWER............................................................................................................................................. 16 7.1 STANDARD APPLICABLE....................................................................................................................................... 16 7.2 TEST PROCEDURE..................................................................................................................................................16 7.3 ENVIRONMENTAL CONDITIONS.............................................................................................................................16 7.4 SUMMARY OF TEST RESULTS/PLOTS.................................................................................................................... 16 8. FIELD STRENGTH OF SPURIOUS EMISSIONS.............................................................................................. 19 8.1 STANDARD APPLICABLE....................................................................................................................................... 19 8.2 TEST PROCEDURE..................................................................................................................................................19 8.3 CORRECTED AMPLITUDE & MARGIN CALCULATION........................................................................................... 21 8.4 ENVIRONMENTAL CONDITIONS.............................................................................................................................21 8.5 SUMMARY OF TEST RESULTS/PLOTS.................................................................................................................... 21 9. OUT OF BAND EMISSIONS..................................................................................................................................27 9.1 STANDARD APPLICABLE....................................................................................................................................... 27 9.2 TEST PROCEDURE..................................................................................................................................................27 9.3 ENVIRONMENTAL CONDITIONS.............................................................................................................................28 9.4 SUMMARY OF TEST RESULTS/PLOTS.................................................................................................................... 28 10. CONDUCTED EMISSIONS..................................................................................................................................30 10.1 TEST PROCEDURE................................................................................................................................................30 10.2 BASIC TEST SETUP BLOCK DIAGRAM.................................................................................................................30 10.3 ENVIRONMENTAL CONDITIONS...........................................................................................................................30 10.4 TEST RECEIVER SETUP........................................................................................................................................31 10.5 SUMMARY OF TEST RESULTS/PLOTS.................................................................................................................. 31 10.6 CONDUCTED EMISSIONS TEST DATA..................................................................................................................31 Report No.: BSL12139801RF Page 2 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF 1. GENERAL INFORMATION 1.1 Product Description for Equipment Under Test (EUT) Client Information Applicant: Shenzhen Hanrongda Electronic Co.,Ltd Address of applicant: No.21,LiYuan Xia,XinLi Road,PingHu Town,LongGang District Shenzhen Manufacturer: Shenzhen Hanrongda Electronic Co.,Ltd Address of manufacturer: No.21,LiYuan Xia,XinLi Road,PingHu Town,LongGang District Shenzhen General Description of EUT Product Name: FM headphone with bluetooth Brand Name: N/A Model No.: N/A Rated Voltage: DC 5V from adapter or 3.7V from battery Adapter Information: N/A Note: The test data is gathered from a production sample provided by the manufacturer. Technical Characteristics of EUT Bluetooth Version: V4.0 Frequency Range: 2402-2480MHz RF Output Power: 0.80dBm (Conducted) Modulation: GFSK Quantity of Channels: 40 Channel Separation: 2MHz Type of Antenna: PCB Antenna Gain: 0dBi Lowest Internal Frequency: 32.768KHz Report No.: BSL12139801RF Page 3 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF 1.2 Test Standards The following report is prepared on behalf of the Shenzhen Hanrongda Electronic Co.,Ltd in accordance with FCC Part 15, Subpart C, and section 15.203, 15.205, 15.207, 15.209 and 15.247 of the Federal Communication Commissions rules. The objective is to determine compliance with FCC Part 15, Subpart C, and section 15.203, 15.205, 15.207, 15.209 and 15.247 of the Federal Communication Commissions rules. Maintenance of compliance is the responsibility of the manufacturer. Any modification of the product, which result in lowering the emission, should be checked to ensure compliance has been maintained. 1.3 Test Methodology All measurements contained in this report were conducted with ANSI C63.10-2013, American National Standard for Testing Unlicensed Wireless Devices, and ANSI C63.4-2014, American National Standard for Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in the range of 9 kHz to 40 GHz. The measurement guide KDB 558074 D01 v05 for digital transmission systems shall be performed also. 1.4 Test Facility BSL Testing Co.,LTD. NO. 24, ZH Park, Nantou, Shenzhen, 518000 China Designation Number : CN1217 Test Firm Registration Number: 866035 Tel: 86- 755-26508703 Fax: 86- 755-26508703 Report No.: BSL12139801RF Page 4 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF 1.5 EUT Setup and Test Mode The EUT was operated in the engineering mode to fix the Tx frequency that was for the purpose of the measurements. All testing shall be performed under maximum output power condition, and to measure its highest possible emissions level, more detailed description as follows: Test Mode List Test Mode Description Remark TM1 GFSK(BLE) 2402MHz, 2442MHz, 2480MHz EUT Cable List and Details Cable Description Length (m) Shielded/Unshielded With / Without Ferrite / / / / Special Cable List and Details Cable Description Length (m) Shielded/Unshielded With / Without Ferrite / / / / Auxiliary Equipment List and Details Description Manufacturer Model Serial Number 1.6 Measurement Uncertainty Measurement uncertainty Parameter Conditions Uncertainty RF Output Power Conducted ±0.42dB Occupied Bandwidth Conducted ±1.5% Power Spectral Density Conducted ±1.8dB Conducted Spurious Emission Conducted ±2.17dB Conducted Emissions Conducted ±2.88dB Transmitter Spurious Emissions Radiated ±5.1dB Report No.: BSL12139801RF Page 5 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF 1.7 Test Equipment List and Details Description Manufacturer Model Serial No. Cal Date Due. Date Spectrum Analyzer R&S FSP40 100550 2018-10-08 2019-10-07 Test Receiver R&S ESCI7 US47140102 2018-10-08 2019-10-07 Signal Generator HP 83630B 3844A01028 2018-10-08 2019-10-07 Test Receiver R&S ESPI-3 100180 2018-10-08 2019-10-07 Amplifier Agilent 8449B 4035A00116 2018-10-08 2019-10-07 Amplifier HP 8447E 2945A02770 2018-10-08 2019-10-07 Signal Generator IFR 2023A 202307/242 2018-10-08 2019-10-07 Broadband Antenna SCHAFFNER 2774 2774 2018-10-21 2019-10-20 Biconical and log ELECTRO-METRI EM-6917B-1 171 2018-10-21 2019-10-20 periodic antennas CS Horn Antenna R&S HF906 100253 2018-10-21 2019-10-20 Horn Antenna EM EM-6961 6462 2018-10-21 2019-10-20 LISN R&S ESH3-Z5 100196 2018-10-08 2019-10-07 LISN COM-POWER LI-115 02027 2018-10-08 2019-10-07 3m Semi-Anechoic Chengyu Electron 9 (L)*6 (W)* BSL086 2018-10-08 2019-10-07 Chamber 6 (H) Horn Antenna Schwarzbeck BBHA9170 00814 2018-10-21 2019-10-20 Loop Antenna Schwarzbeck FMZB 1519B 9773 2018-10-21 2019-10-20 Report No.: BSL12139801RF Page 6 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF 2. SUMMARY OF TEST RESULTS FCC Rules Description of Test Item Result § 2.1093 RF Exposure PASS §15.203;§15.247(b)(4)(i) Antenna Requirement PASS §15.205 Restricted Band of Operation PASS §15.207(a) Conducted Emission PASS §15.247(e) Power Spectral Density PASS §15.247(a)(2) 6 dB Bandwidth PASS §15.247(b)(3) RF Output Power PASS §15.209(a) Radiated Emission PASS §15.247(d) Band Edge (Out of Band Emissions) PASS Note: PASS: applicable, N/A: not applicable. Report No.: BSL12139801RF Page 7 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF 3. RF Exposure 3.1 Standard Applicable According to§1.1307 and §2.1093, the portable transmitter must comply the RF exposure requirements. 3.2 Test Result This product complied with the requirement of the RF exposure, please see the RF Exposure Report. Report No.: BSL12139801RF Page 8 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF 4. Antenna Requirement 4.1 Standard Applicable According to FCC Part 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. 4.2 Evaluation Information This product has a PCB antenna, fulfill the requirement of this section. Report No.: BSL12139801RF Page 9 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF 5. Power Spectral Density 5.1 Standard Applicable According to 15.247(a)(1)(iii), For digitally modulated systems, the power spectral density conducted from the intentional radiator to the antenna shall not be greater than 8 dBm in any 3 kHz band during any time interval of continuous transmission. 5.2 Test Procedure According to the KDB 558074 D01 v05, the test method of power spectral density as below: a) Set analyzer center frequency to DTS channel center frequency. b) Set the span to 1.5 times the DTS bandwidth. c) Set the RBW to: 3 kHz ≤ RBW ≤ 100 kHz. d) Set the VBW ≥ 3 × RBW. e) Detector = peak. f) Sweep time = auto couple. g) Trace mode = max hold. h) Allow trace to fully stabilize. i) Use the peak marker function to determine the maximum amplitude level within the RBW. j) If measured value exceeds limit, reduce RBW (no less than 3 kHz) and repeat. 5.3 Environmental Conditions Temperature: 26 C Relative Humidity: 54 ATM Pressure: 1011 mbar 5.4 Summary of Test Results/Plots Test Channel Power Spectral Density Limit Test Mode MHz dBm/3kHz dBm/3kHz 2402 -22.36 8 GFSK(BLE) 2442 -21.32 8 2480 -24.25 8 Please refer to the following test plots: Report No.: BSL12139801RF Page 10 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF Low Channel * RBW 3 kHz Marker 1 [T1 ] * VBW 10 kHz -22.36 dBm Ref 1.8 dBm * Att 30 dB SWT 225 ms 2.401984000 GHz 0 Offset 1.5 dB A -10 1 PK VIEW -20 1 LVL -30 -40 -50 3DB -60 -70 -80 -90 Center 2.402 GHz 200 kHz/ Span 2 MHz Middle Channel Date: 23.JAN.2019 13:03:18 * RBW 3 kHz Marker 1 [T1 ] * VBW 10 kHz -21.32 dBm Ref 11.5 dBm * Att 30 dB SWT 225 ms 2.441984000 GHz 10 Offset 1.5 dB A 0 1 PK VIEW -10 LVL 1 -20 -30 -40 3DB -50 -60 -70 -80 Center 2.442 GHz 200 kHz/ Span 2 MHz Date: 23.JAN.2019 13:08:32 Report No.: BSL12139801RF Page 11 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF High Channel * RBW 3 kHz Marker 1 [T1 ] * VBW 10 kHz -24.25 dBm Ref 11.5 dBm * Att 30 dB SWT 225 ms 2.479984000 GHz 10 Offset 1.5 dB A 0 1 PK VIEW -10 LVL -20 1 -30 -40 3DB -50 -60 -70 -80 Center 2.48 GHz 200 kHz/ Span 2 MHz Date: 23.JAN.2019 13:20:11 Report No.: BSL12139801RF Page 12 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF 6. 6dB Bandwidth 6.1 Standard Applicable According to 15.247(a)(2). Systems using digital modulation techniques may operate in the 902–928 MHz, 2400–2483.5 MHz, and 5725–5850 MHz bands. The minimum 6 dB bandwidth shall be at least 500 kHz. 6.2 Test Procedure a) Set RBW = 100 kHz. b) Set the video bandwidth (VBW) ≥ 3 × RBW. c) Detector = Peak. d) Trace mode = max hold. e) Sweep = auto couple. f) Allow the trace to stabilize. g) Measure the maximum width of the emission that is constrained by the frequencies associated with the two outermost amplitude points (upper and lower frequencies) that are attenuated by 6 dB relative to the maximum level measured in the fundamental emission. 6.3 Environmental Conditions Temperature: 25 C Relative Humidity: 53 ATM Pressure: 1018 mbar 6.4 Summary of Test Results/Plots Test Channel 6 dB Bandwidth Limit Test Mode MHz kHz kHz 2402 708 ≥500 GFSK(BLE) 2442 708 ≥500 2480 708 ≥500 Please refer to the following test plots: Report No.: BSL12139801RF Page 13 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF For BLE Low Channel: * RBW 100 kHz Marker 2 [T1 ] * VBW 300 kHz -7.18 dBm Ref 11.5 dBm * Att 30 dB SWT 2.5 ms 2.402252000 GHz 10 Offset 1.5 dB Marker 1 [T1 ] -14.04 dBm 2.401628000 GHz A 0 Delta 1 [T1 ] 1 PK 2 1.59 dB VIEW -10 1 708.000000000 kHz LVL 1 D1 -13.18 dBm -20 -30 -40 3DB -50 -60 -70 -80 Center 2.402 GHz 300 kHz/ Span 3 MHz Middle Channel: * RBW 100 kHz Marker 2 [T1 ] Date: 22.JAN.2019 14:37:03 * VBW 300 kHz -7.11 dBm Ref 11.5 dBm * Att 30 dB SWT 2.5 ms 2.442000000 GHz 10 Offset 1.5 dB Marker 1 [T1 ] -13.52 dBm 2.441634000 GHz A 0 Delta 1 [T1 ] 1 PK 2 0.84 dB VIEW -10 1 708.000000000 kHz LVL 1 D1 -13.11 dBm -20 -30 -40 3DB -50 -60 -70 -80 Center 2.442 GHz 300 kHz/ Span 3 MHz Date: 23.JAN.2019 10:50:18 Report No.: BSL12139801RF Page 14 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF High Channel: * RBW 100 kHz Marker 2 [T1 ] * VBW 300 kHz -10.01 dBm Ref 11.5 dBm * Att 30 dB SWT 2.5 ms 2.480000000 GHz 10 Offset 1.5 dB Marker 1 [T1 ] -16.14 dBm 2.479640000 GHz A 0 Delta 1 [T1 ] 1 PK 0.09 dB VIEW 2 -10 708.000000000 kHz LVL 1 1 D1 -16.01 dBm -20 -30 -40 3DB -50 -60 -70 -80 Center 2.48 GHz 300 kHz/ Span 3 MHz Date: 23.JAN.2019 10:57:25 Report No.: BSL12139801RF Page 15 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF 7. RF Output Power 7.1 Standard Applicable According to 15.247(b)(3). For systems using digital modulation in the 902–928 MHz, 2400–2483.5 MHz, and 5725–5850 MHz bands: 1 Watt. 7.2 Test Procedure According to section KDB-558074 D01 v04 section 9.1.1, this procedure shall be used when the measurement instrument has available a resolution bandwidth that is greater than the DTS bandwidth. a) Set the RBW ≥ DTS bandwidth. b) Set VBW ≥ 3 × RBW. c) Set span ≥ 3 x RBW d) Sweep time = auto couple. e) Detector = peak. f) Trace mode = max hold. g) Allow trace to fully stabilize. h) Use peak marker function to determine the peak amplitude level. 7.3 Environmental Conditions Temperature: 26 C Relative Humidity: 57 ATM Pressure: 1011 mbar 7.4 Summary of Test Results/Plots Frequency Reading Output Power Limit Test Mode MHz dBm mW mW 2402 0.80 1.20 1000 GFSK(BLE) 2442 0.76 1.19 1000 2480 -2.84 0.52 1000 Note: the antenna gain of 0dBi less than 6dBi maximum permission antenna gain value based on 1 watt peak output power limit. Report No.: BSL12139801RF Page 16 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF For BLE: Low Channel: * RBW 3 MHz Marker 1 [T1 ] * VBW 3 MHz 0.80 dBm Ref 11.5 dBm * Att 30 dB SWT 2.5 ms 2.402252000 GHz 10 Offset 1.5 dB 1 A 0 1 PK VIEW -10 LVL -20 -30 -40 3DB -50 -60 -70 -80 Center 2.402 GHz 900 kHz/ Span 9 MHz Middle Channel: * RBW 3 MHz Marker 1 [T1 ] Date: 23.JAN.2019 14:14:36 * VBW 3 MHz 0.76 dBm Ref 11.5 dBm * Att 30 dB SWT 2.5 ms 2.442054000 GHz 10 Offset 1.5 dB 1 A 0 1 PK VIEW -10 LVL -20 -30 -40 3DB -50 -60 -70 -80 Center 2.442 GHz 900 kHz/ Span 9 MHz Date: 23.JAN.2019 14:21:42 Report No.: BSL12139801RF Page 17 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF High Channel: * RBW 3 MHz Marker 1 [T1 ] * VBW 3 MHz -2.84 dBm Ref 11.5 dBm * Att 30 dB SWT 2.5 ms 2.480144000 GHz 10 Offset 1.5 dB A 0 1 1 PK VIEW -10 LVL -20 -30 -40 3DB -50 -60 -70 -80 Center 2.48 GHz 900 kHz/ Span 9 MHz Date: 23.JAN.2019 14:25:06 Report No.: BSL12139801RF Page 18 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF 8. Field Strength of Spurious Emissions 8.1 Standard Applicable According to §15.247(d), in any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in §15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in §15.209(a). The emission limit in this paragraph is based on measurement instrumentation employing an average detector. The provisions in §15.35 for limiting peak emissions apply. Spurious Radiated Emissions measurements starting below or at the lowest crystal frequency. 8.2 Test Procedure The setup of EUT is according with per ANSI C63.10-2013 measurement procedure. The specification used was with the FCC Part 15.205 15.247(a) and FCC Part 15.209 Limit. The external I/O cables were draped along the test table and formed a bundle 30 to 40 cm long in the middle. The spacing between the peripherals was 10 cm. Report No.: BSL12139801RF Page 19 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF Antenna Tower 1m-4m 3m EUT SYS 1.5m Turntable Table To EMI Receiver Ground Plane Frequency :9kHz-30MHz Frequency :30MHz-1GHz Frequency :Above 1GHz RBW=10KHz, RBW=120KHz, RBW=1MHz, VBW =30KHz VBW=300KHz VBW=3MHz(Peak), 10Hz(AV) Sweep time= Auto Sweep time= Auto Sweep time= Auto Trace = max hold Trace = max hold Trace = max hold Detector function = peak Detector function = peak, QP Detector function = peak, AV Report No.: BSL12139801RF Page 20 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF 8.3 Corrected Amplitude & Margin Calculation The Corrected Amplitude is calculated by adding the Antenna Factor and the Cable Factor, and subtracting the Amplifier Gain from the Amplitude reading. The basic equation is as follows: Corr. Ampl. = Indicated Reading + Ant. Factor + Cable Loss – Ampl. Gain The “Margin” column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of -6dB  V means the emission is 6dB  V below the maximum limit. The equation for margin calculation is as follows: Margin = Corr. Ampl. – FCC Part 15 Limit 8.4 Environmental Conditions Temperature: 25 C Relative Humidity: 52 ATM Pressure: 1012 mbar 8.5 Summary of Test Results/Plots According to the data below, the FCC Part 15.205, 15.209 and 15.247 standards, and had the worst cases: Note: 1. Worst-case radiated emission below 1GHz is GFSK (CH Low) mode. 2. Worst-case radiated emission above 1GHz is GFSK (CH Low, Middle, High) mode. Report No.: BSL12139801RF Page 21 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF The Worst Test Data Below 1GHz GFSK (CH Low) mode: Plot of Radiated Emissions Test Specification: Horizontal Report No.: BSL12139801RF Page 22 of 33 FCC Part 15.247

80.0 dBu¥/m 70 60 FCC Part 15 Class C 3M Radiation 50 Margin —6 uB 30.000 40 50 60 70 80 (MHz] 300 400 5oo 600 700 1000.000 Reading Correct Measure— Antenna Table No. Mk. Freq. Level Factor ment Limit Over Height Degree MHz dBuy dBu\Vim dBuVim dBuVim dB Detector cm degree 1 43.3534 22.40 3.56 25.96 40.00 —14.04 QP 2 63.9828 20.30 140 21.70 40.00 —18.30 QP 3 95.7622 18.51 1.38 19.89 43.50 —23.61 QP 4 207.8501 17.66 3.60 21.26 43.50 —22.24 QP § 360.4476 14.45 8.84 23.29 46.00 —22.71 QP 6 * 824.5968 16.12 18.00 34.12 46.00 —11.48 QP

BSL Testing Co.,LTD. Report No.: BSL12139801RF The Worst Spurious Emissions Above 1GHz Transmitting: BLE mode: Frequency Result Limit Margin Polar Detector (MHz) (dBuV/m) (dBuV/m) (dB) H/V Low Channel-2402MHz 4804 53.47 74 -20.53 H PK 4804 41.85 54 -12.15 H AV 7206 52.56 74 -21.44 H PK 7206 40.81 54 -13.19 H AV 4804 51.20 74 -22.8 V PK 4804 42.14 54 -11.86 V AV 7206 52.24 74 -21.76 V PK 7206 43.63 54 -10.37 V AV Middle Channel-2442MHz 4884 52.35 74 -21.65 H PK 4884 43.24 54 -10.76 H AV 7326 51.74 74 -22.26 H PK 7326 43.81 54 -10.19 H AV 4884 52.96 74 -21.04 V PK 4884 38.20 54 -15.8 V AV 7326 50.00 74 -24.00 V PK 7326 42.14 54 -11.86 V AV High Channel-2480MHz 4960 51.88 74 -22.12 H PK 4960 43.96 54 -10.04 H AV 7440 52.84 74 -21.16 H PK 7440 40.57 54 -13.43 H AV 4960 52.88 74 -21.12 V PK 4960 43.41 54 -10.59 V AV 7440 51.45 74 -22.55 V PK 7440 42.25 54 -11.75 V AV Note: Testing is carried out with frequency rang 9kHz to the tenth harmonics, other than listed in the table above are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. Report No.: BSL12139801RF Page 24 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF Spurious Emission(Conducted) For BLE Low channel: * RBW 100 kHz Marker 2 [T1 ] * VBW 300 kHz -41.89 dBm Ref 11.5 dBm * Att 30 dB SWT 2.7 s 26.784240000 GHz 10 Offset 1.5 dB Marker 1 [T1 ] -1.85 dBm 2.403360000 GHz A 1 0 1 PK VIEW -10 LVL -20 D1 -21.85 dBm -30 2 -40 3DB -50 -60 -70 -80 Start 30 MHz 2.697 GHz/ Stop 27 GHz Middle channel: * RBW 100 kHz Marker 2 [T1 ] Date: 23.JAN.2019 14:39:53 * VBW 300 kHz -42.16 dBm Ref 11.5 dBm * Att 30 dB SWT 2.7 s 21.767820000 GHz 10 Offset 1.5 dB Marker 1 [T1 ] -1.20 dBm 1 2.403360000 GHz A 0 1 PK VIEW -10 LVL -20 D1 -21.2 dBm -30 2 -40 3DB -50 -60 -70 -80 Start 30 MHz 2.697 GHz/ Stop 27 GHz Date: 23.JAN.2019 14:35:01 Report No.: BSL12139801RF Page 25 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF High channel: * RBW 100 kHz Marker 2 [T1 ] * VBW 300 kHz -42.26 dBm Ref 11.5 dBm * Att 30 dB SWT 2.7 s 24.842400000 GHz 10 Offset 1.5 dB Marker 1 [T1 ] -3.96 dBm 2.480144000 GHz A 0 1 1 PK VIEW -10 LVL -20 D1 -23.96 dBm -30 2 -40 3DB -50 -60 -70 -80 Start 30 MHz 2.697 GHz/ Stop 27 GHz Date: 23.JAN.2019 14:30:37 Report No.: BSL12139801RF Page 26 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF 9. Out of Band Emissions 9.1 Standard Applicable According to §15.247 (d) In any 100 kHz bandwidth outside the frequency band in which the spread spectrum or digitally modulated intentional radiator is operating, the radio frequency power that is produced by the intentional radiator shall be at least 20 dB below that in the 100 kHz bandwidth within the band that contains the highest level of the desired power, based on either an RF conducted or a radiated measurement, provided the transmitter demonstrates compliance with the peak conducted power limits. If the transmitter complies with the conducted power limits based on the use of RMS averaging over a time interval, as permitted under paragraph (b)(3) of this section, the attenuation required under this paragraph shall be 30 dB instead of 20 dB. Attenuation below the general limits specified in §15.209(a) is not required. In addition, radiated emissions which fall in the restricted bands, as defined in §15.205(a), must also comply with the radiated emission limits specified in §15.209(a). 9.2 Test Procedure According to the KDB 558074 D01 v05, the band-edge radiated test method as follows: Set span = wide enough to capture the peak level of the emission operating on the channel closest to the bandedge, as well as any modulation products which fall outside of the authorized band of operation (2310MHz to 2420MHz for low bandedge, 2460MHz to 2500MHz for the high bandedge) RBW = 1MHz, VBW = 1MHz for peak value measured RBW = 1MHz, VBW = 10Hz for average value measured Sweep = auto; Detector function = peak/average; Trace = max hold All the trace to stabilize, set the marker on the emission at the bandedge, or on the highest modulation product outside of the band, if this level is greater than that at the bandedge. Enable the marker-delta function, then use the marker-to-peak function to move the marker to the peak of the in-band emission. Those emission must comply with the 15.209 limit for fall in the restricted bands listed in section 15.205. Note that the method of measurement KDB publication number: 913591 may be used for the radiated bandedge measurements. According to the KDB 558074 D01 v05, the conducted spurious emissions test method as follows: 1. Set start frequency to DTS channel edge frequency. 2. Set stop frequency so as to encompass the spectrum to be examined. 3. Set RBW = 100 kHz. 4. Set VBW ≥ 300 kHz. 5. Detector = peak. 6. Trace Mode = max hold. 7. Sweep = auto couple. 8. Allow the trace to stabilize (this may take some time, depending on the extent of the span). 9. Use peak marker function to determine maximum amplitude of all unwanted emissions within any 100 kHz bandwidth. Ensure that the amplitude of all unwanted emissions outside of the authorized frequency band (excluding restricted frequency bands) are attenuated by at least the minimum requirements specified in section 8.1. Report the three highest emissions relative to the limit. Report No.: BSL12139801RF Page 27 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF 9.3 Environmental Conditions Temperature: 23C Relative Humidity: 54 ATM Pressure: 1011 mbar 9.4 Summary of Test Results/Plots Bandedge (Radiated) Lowest Bandedge-BLE Channel Freq.(MHz) Level(dBuV) Limit(dBuV) Margin(dB) Detector 2390 49.25 74 -24.75 Peak 2390 37.36 54 -16.64 Average LOW 2400 52.24 74 -21.76 Peak LOW 2400 39.51 54 -14.49 Average HIGH 2483.5 41.76 74 -32.24 Peak HIGH 2483.5 36.85 54 -17.15 Average Report No.: BSL12139801RF Page 28 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF Bandedge (Conducted) Lowest * RBW 100 kHz Marker 1 [T1 ] * VBW 300 kHz -0.10 dBm Ref 11.5 dBm * Att 30 dB SWT 15 ms 2.401920000 GHz 10 Offset 1.5 dB Marker 2 [T1 ] -56.38 dBm 1 A 2.310000000 GHz 0 Marker 3 [T1 ] 1 PK -56.20 dBm VIEW -10 2.390000000 GHz LVL Marker 4 [T1 ] -55.11 dBm -20 D1 -20.1 dBm 2.400000000 GHz -30 -40 3DB -50 4 2 3 -60 -70 -80 F2 F1 Start 2.3 GHz 14 MHz/ Stop 2.44 GHz High Channel: * RBW 100 kHz Marker 1 [T1 ] Date: 23.JAN.2019 14:46:30 * VBW 300 kHz -3.29 dBm Ref 11.5 dBm * Att 30 dB SWT 15 ms 2.479820000 GHz 10 Offset 1.5 dB Marker 2 [T1 ] -54.08 dBm 2.483500000 GHz A 0 1 Marker 3 [T1 ] 1 PK -55.19 dBm VIEW -10 2.500000000 GHz LVL Marker 4 [T1 ] -52.67 dBm -20 2.496140000 GHz D1 -23.29 dBm -30 -40 3DB -50 4 2 3 -60 -70 -80 F2 F1 Start 2.44 GHz 11 MHz/ Stop 2.55 GHz Date: 23.JAN.2019 14:49:39 Report No.: BSL12139801RF Page 29 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF 10. Conducted Emissions 10.1 Test Procedure The setup of EUT is according with per ANSI C63.4-2014 measurement procedure. The specification used was with the FCC Part 15.207 Limit. The external I/O cables were draped along the test table and formed a bundle 30 to 40 cm long in the middle. The spacing between the peripherals was 10 cm. 10.2 Basic Test Setup Block Diagram EUT Notebook LISN 1.0 m 1.5 To Receiver Non-conduction table 80 cm above Ground Plane 1. 5 m 10.3 Environmental Conditions Temperature: 25 C Relative Humidity: 52 ATM Pressure: 1012 mbar Report No.: BSL12139801RF Page 30 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF 10.4 Test Receiver Setup During the conducted emission test, the test receiver was set with the following configurations: Start Frequency............................................................................ 150 kHz Stop Frequency............................................................................ 30 MHz Sweep Speed................................................................................ Auto IF Bandwidth............................................................................... 10 kHz Quasi-Peak Adapter Bandwidth.................................................. 9 kHz Quasi-Peak Adapter Mode...........................................................Normal 10.5 Summary of Test Results/Plots According to the data in section 10.6, the EUT complied with the FCC Part 15.207 Conducted margin for this device 10.6 Conducted Emissions Test Data Note: We pre-scan all mode, the worst data is GFSK (Low channel). Report No.: BSL12139801RF Page 31 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF Plot of Conducted Emissions The Worst Test Data GFSK (Low channel): Test Specification: Neutral Report No.: BSL12139801RF Page 32 of 33 FCC Part 15.247

BSL Testing Co.,LTD. Report No.: BSL12139801RF Test Specification: Line ***** END OF REPORT ***** Report No.: BSL12139801RF Page 33 of 33 FCC Part 15.247


Document Created: 2019-04-08 17:04:18
Document Modified: 2019-04-08 17:04:18
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC