test report

FCC ID: 2APPZ-I33V

Test Report

Download: PDF
FCCID_4380943

CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel: +86-755-27521059 Fax: +86-755-27521011 Http://www.sz-ctc.com.cn TEST REPORT Report No. ...................................... : GTI20191250E-2 FCC ID……………………………...…: 2APPZ-I33V Applicant......................................... : Fanvil Technology Co., LTD. 4F, Block A, Bldg#1, GaoXinQi Hi-TechPark Phase-II, 67th District, Address…………………..………..….: Bao'An, Shenzhen, China Manufacturer....................................: Fanvil Technology Co., LTD. 4F, Block A, Bldg#1, GaoXinQi Hi-TechPark Phase-II, 67th District, Address............................................: Bao'An, Shenzhen, China Product Name ................................ : IP Door Phone Trade Mark....................................... : Fanvil Model/Type reference ...................... : i33V Listed Model(s) ................................ : i33VF Standard ....................................... : FCC CFR Title 47 Part 15 Subpart C Date of receipt of test sample……: Jul. 04, 2019 Date of testing……………………..: Jul. 05, 2019 ~ Jul. 22, 2019 Date of issue……………………....: Jul. 22, 2019 Result………………………………: PASS Compiled by: (Printed name + signature) Terry Su Supervised by: ( Printed name + signature) Eric Zhang Approved by: ( Printed name + signature) Walter Chen Testing Laboratory Name.............. : CTC Laboratories, Inc. Address ............................................ : 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China This test report may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product endorsement by CTC. The test results in the report only apply to the tested sample. The test report shall be invalid without all the signatures of testing engineers, reviewer and approver. Any objections must be raised to CTC within 15 days since the date when the report is received. It will not be taken into consideration beyond this limit. The test report merely correspond to the test sample.

Page 2 of 29 Report No.: GTI20191250E-2 Table of Contents Page 1. TEST SUMMARY.................................................................................................................................................... 3 1.1. TEST STANDARDS.......................................................................................................................................................... 3 1.2. REPORT VERSION .......................................................................................................................................................... 3 1.3. TEST DESCRIPTION ........................................................................................................................................................ 4 1.4. TEST FACILITY .............................................................................................................................................................. 5 1.5. MEASUREMENT UNCERTAINTY ........................................................................................................................................ 5 1.6. ENVIRONMENTAL CONDITIONS ........................................................................................................................................ 6 1.7. EUT OPERATION STATE.................................................................................................................................................. 6 1. GENERAL INFORMATION....................................................................................................................................... 7 1.1. CLIENT INFORMATION ................................................................................................................................................... 7 1.2. GENERAL DESCRIPTION OF EUT ...................................................................................................................................... 7 1.3. ACCESSORY EQUIPMENT INFORMATION ............................................................................................................................ 7 1.4. MEASUREMENT INSTRUMENTS LIST ................................................................................................................................. 8 2. TEST ITEM AND RESULTS ..................................................................................................................................... 10 2.1. CONDUCTED EMISSION ................................................................................................................................................ 10 2.2. RADIATED EMISSION ................................................................................................................................................... 13 2.3. OCCUPIED BANDWIDTH 20 DB BANDWIDTH .................................................................................................................... 21 2.4. FIELD STRENGTH OF THE FUNDAMENTAL ......................................................................................................................... 23 2.5. ANTENNA REQUIREMENT ............................................................................................................................................. 26 3. LABEL AND LABEL LOCATION .............................................................................................................................. 27 4. EUT TEST PHOTOS ............................................................................................................................................... 28 3. PHOTOGRAPHS OF EUT CONSTRUCTIONAL ......................................................................................................... 29 CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 3 of 29 Report No.: GTI20191250E-2 1. TEST SUMMARY 1.1. Test Standards The tests were performed according to following standards: FCC Rules Part 15C: Intentional Radiators ANSI C63.10-2013: American National Standard for Testing Unlicensed Wireless Devices. 1.2. Report version Revised No. Date of issue Description 01 Jul. 22, 2019 Original CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 4 of 29 Report No.: GTI20191250E-2 1.3. Test Description FCC Part 15 Subpart C Test Item Standard Section Result Test Engineer Conducted Emission 15.207 Pass Terry Su Radiated Emissions 15.209 Pass Terry Su Field Strength of the Fundamental 15.209 Pass Terry Su Occupied Bandwidth and 20dB Bandwidth 15.215 Pass Terry Su Antenna requirement 15.203 Pass Terry Su Note: N/A: Not applicable. The measurement uncertainty is not included in the test result. CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 5 of 29 Report No.: GTI20191250E-2 1.4. Test Facility Address of the report laboratory CTC Laboratories, Inc. Add: 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Laboratory accreditation The test facility is recognized, certified, or accredited by the following organizations: CNAS-Lab Code: L5365 CTC Laboratories, Inc. has been assessed and proved to be in compliance with CNAS-CL01 Accreditation Criteria for Testing and Calibration Laboratories (identical to ISO/IEC17025: 2005 General Requirements) for the Competence of Testing and Calibration Laboratories. A2LA-Lab Cert. No.: CN1208 CTC Laboratories, Inc. EMC Laboratory has been accredited by A2LA for technical competence in the field of electrical testing, and proved to be in compliance with ISO/IEC 17025: 2005 General Requirements for the Competence of Testing and Calibration Laboratories and any additional program requirements in the identified field of testing. IC Registration No.: 9783A-1 The 3m alternate test site of CTC Laboratories, Inc. EMC Laboratory has been registered by Certification and Engineer Bureau of Industry Canada for the performance of with Registration NO.: 9783A-1 on Jan, 2016. FCC-Registration No.: 951311 CTC Laboratories, Inc. EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration 951311, Aug 26, 2017 1.5. Measurement Uncertainty The data and results referenced in this document are true and accurate. The reader is cautioned that there may be errors within the calibration limits of the equipment and facilities. The measurement uncertainty was calculated for all measurements listed in this test report acc. to TR-100028-01” Electromagnetic compatibility and Radio spectrum Matters (ERM);Uncertainties in the measurement of mobile radio equipment characteristics; Part 1” and TR-100028-02 “Electromagnetic compatibility and Radio spectrum Matters (ERM);Uncertainties in the measurement of mobile radio equipment characteristics; Part 2 “ and is documented in the CTC Laboratories, Inc. quality system acc. to DIN EN ISO/IEC 17025. Furthermore, component and process variability of devices similar to that tested may result in additional deviation. The manufacturer has the sole responsibility of continued compliance of the device. Below is the best measurement capability for CTC Laboratories, Inc. CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 6 of 29 Report No.: GTI20191250E-2 Test Items Measurement Uncertainty Notes Transmitter power conducted 0.42 dB (1) Transmitter power Radiated 2.14 dB (1) Conducted spurious emissions 9kHz~40GHz 1.60 dB (1) Radiated spurious emissions 9kHz~40GHz 2.20 dB (1) Conducted Emissions 9kHz~30MHz 3.20 dB (1) Radiated Emissions 30~1000MHz 4.70 dB (1) Radiated Emissions 1~18GHz 5.00 dB (1) Radiated Emissions 18~40GHz 5.54 dB (1) Occupied Bandwidth --------- (1) Note (1): This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=1.96. 1.6. Environmental conditions During the measurement the environmental conditions were within the listed ranges: Temperature: 15~35°C Relative Humidity: 30~60 % Air Pressure: 950~1050kPa 1.7. EUT Operation state The EUT has been tested under typical operating condition. The Applicant provides software to control the EUT for staying in continuous transmitting mode for testing. CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 7 of 29 Report No.: GTI20191250E-2 1. GENERAL INFORMATION 1.1. Client Information Applicant: Fanvil Technology Co., LTD. 4F, Block A, Bldg#1, GaoXinQi Hi-TechPark Phase-II, 67th District, Address: Bao'An, Shenzhen, China Manufacturer: Fanvil Technology Co., LTD. 4F, Block A, Bldg#1, GaoXinQi Hi-TechPark Phase-II, 67th District, Address: Bao'An, Shenzhen, China 1.2. General Description of EUT Product Name: IP Door Phone Model/Type reference: Fanvil Marketing Name: i33V Listed Model(s): i33VF All these models are identical in the same PCB, layout and electrical Model Difference: circuit, the only difference is way to install. Power supply: 12Vdc/1A from External Adapter Supplied from POE Hardware version: N/A Software version: N/A RF Parameter Operation frequency: 125KHz Antenna type: Loop Antenna 1.3. Accessory Equipment information Equipment Information Name Model S/N Manufacturer AC/DC Adapter LPL-V0121201100AT --- Sagemcom Cable Information Name Shielded Type Ferrite Core Length / / / / CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 8 of 29 Report No.: GTI20191250E-2 1.4. Measurement Instruments List Tonscend JS0806-2 Test system Item Test Equipment Manufacturer Model No. Serial No. Calibrated until 1 Spectrum Analyzer Rohde & Schwarz FSU26 100105 Dec. 27, 2019 2 Spectrum Analyzer Rohde & Schwarz FUV40-N 101331 Dec. 27, 2019 MXG Vector Signal 3 Agilent N5182A MY47420864 Dec. 27, 2019 Generator 4 Signal Generator Agilent E8257D MY46521908 Dec. 27, 2019 5 Power Sensor Agilent U2021XA MY5365004 Dec. 27, 2019 6 Power Sensor Agilent U2021XA MY5365006 Dec. 27, 2019 Simultaneous 7 Agilent U2531A TW54493510 Dec. 27, 2019 Sampling DAQ 8 Climate Chamber TABAI PR-4G A8708055 Dec. 27, 2019 Wideband Radio 9 Rohde & Schwarz CMW500 116410 Dec. 27, 2019 Communication Tester 10 Climate Chamber ESPEC MT3065 / Dec. 27, 2019 300328 v2.1.1 test 11 TONSCEND v2.6 / / system Item Test Equipment Manufacturer Model No. Serial No. Calibrated until 1 EMI Test Receiver Rohde & Schwarz ESCI 100658 Dec. 27, 2019 2 High pass filter micro-tranics HPM50111 142 Dec. 27, 2019 3 Log-Bicon Antenna Schwarzbeck CBL6141A 4180 Dec. 27, 2019 Ultra-Broadband 4 SchwarzBeck BBHA9170 25841 Dec. 27, 2019 Antenna 5 Loop Antenna LAPLAC RF300 9138 Dec. 27, 2019 6 Loop Antenna ETS 6507 146 Aug. 26, 2019 7 Spectrum Analyzer Rohde & Schwarz FSU26 100105 Dec. 27, 2019 8 Horn Antenna Schwarzbeck BBHA 9120D 647 Dec. 27, 2019 9 Pre-Amplifier HP 8447D 1937A03050 Dec. 27, 2019 10 Pre-Amplifier EMCI EMC051835 980075 Dec. 27, 2019 11 Antenna Mast UC UC3000 N/A N/A 12 Turn Table UC UC3000 N/A N/A 13 Cable Below 1GHz Schwarzbeck AK9515E 33155 Dec. 27, 2019 14 Cable Above 1GHz Hubersuhner SUCOFLEX102 DA1580 Dec. 27, 2019 15 Splitter Mini-Circuit ZAPD-4 400059 Dec. 27, 2019 16 RF Connection Cable HUBER+SUHNER RE-7-FL N/A Dec. 27, 2019 Chengdu 17 RF Connection Cable --- --- Dec. 27, 2019 E-Microwave Compliance 18 High pass filter BSU-6 34202 Dec. 27, 2019 Direction systems CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

sork ng n merevere n qg n werbwe on eor d nc nnnernnare en nos neren nenennn n n nere snn nuns nn nemnn rnenn n n rear n n neten n n enr nne movn n nnarnaren nn ner n nar se un n narn ncb nar n n en neeen nnn en n en ne n n n nn apccrsyptcree rvie qy rvv e vegvis roene qxeve sez d van r w a a va uen ie se vevvze en up en t 2o rer wn nernen i enb e bevra eb rra e sn sba db un seb en e eperee w n nepetme ie n uen in n n eapne gec s en e el en

Page 10 of 29 Report No.: GTI20191250E-2 2. TEST ITEM AND RESULTS 2.1. Conducted Emission Limit FCC CFR Title 47 Part 15 Subpart C Section 15.207/ RSS-Gen 7.2: Limit (dBuV) Frequency range (MHz) Quasi-peak Average 0.15-0.5 66 to 56* 56 to 46* 0.5-5 56 46 5-30 60 50 Notes: (1) *Decreasing linearly with logarithm of the frequency. (2) The lower limit shall apply at the transition frequencies. (3) The limit decrease in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz. Test Configuration Test Procedure 1. The EUT was setup according to ANSI C63.10:2013 requirements. 2. The EUT was placed on a platform of nominal size, 1 m by 1.5 m, raised 80 cm above the conducting ground plane. The vertical conducting plane was located 40 cm to the rear of the EUT. All other surfaces of EUT were at least 80 cm from any other grounded conducting surface. 3. The EUT and simulators are connected to the main power through a line impedances stabilization network (LISN). The LISN provides a 50ohm /50uH coupling impedance for the measuring equipment. The peripheral devices are also connected to the main power through a LISN. (Please refer to the block diagram of the test setup and photographs) 4. Each current-carrying conductor of the EUT power cord, except the ground (safety) conductor, was individually connected through a LISN to the input power source. 5. The excess length of the power cord between the EUT and the LISN receptacle were folded back and forth at the center of the lead to form a bundle not exceeding 40 cm in length. 6. Conducted Emissions were investigated over the frequency range from 0.15MHz to 30MHz using a receiver bandwidth of 9 kHz. 7. During the above scans, the emissions were maximized by cable manipulation. CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 11 of 29 Report No.: GTI20191250E-2 Test Mode: Please refer to the clause 1.7. Test Results Test Voltage: AC 120V/60 Hz Terminal: Line Emission Level= Read Level+ Correct Factor CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 12 of 29 Report No.: GTI20191250E-2 Test Voltage: AC 120V/60 Hz Terminal: Neutral Emission Level= Read Level+ Correct Factor CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 13 of 29 Report No.: GTI20191250E-2 2.2. Radiated Emission FCC Limit Radiated Emission Limits (9 kHz~1000 MHz) Frequency Field Strength Measurement Distance (MHz) (microvolt/meter) (meters) 0.009~0.490 2400/F(KHz) 300 0.490~1.705 24000/F(KHz) 30 1.705~30.0 30 30 30~88 100 3 88~216 150 3 216~960 200 3 Above 960 500 3 Radiated Emission Limit (Above 1000MHz) Frequency Distance Meters(at 3m) (MHz) Peak Average Above 1000 74 54 Note: (1) The tighter limit applies at the band edges. (2) Emission Level (dBuV/m)=20log Emission Level (uV/m). Test Configuration Below 30MHz Test Setup CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 14 of 29 Report No.: GTI20191250E-2 Below 1000MHz Test Setup Above 1GHz Test Setup Test Procedure 1. The EUT was setup and tested according to ANSI C63.10:2013 2. The EUT is placed on a turn table which is 0.8 meter above ground for below 1 GHz, and 1.5 m for above 1 GHz. The turn table is rotated 360 degrees to determine the position of the maximum emission level. 3. The EUT was set 3 meters from the receiving antenna, which was mounted on the top of a variable height antenna tower. 4. For each suspected emission, the EUT was arranged to its worst case and then tune the Antenna tower (from 1 m to 4 m) and turntable (from 0 degree to 360 degrees) to find the maximum reading. A pre-amp and a high pass filter are used for the test in order to get better signal level to comply with the guidelines. 5. Set to the maximum power setting and enable the EUT transmit continuously. 6. Use the following spectrum analyzer settings (1) Span shall wide enough to fully capture the emission being measured; (2) Below 1 GHz: RBW=120 kHz, VBW=300 kHz, Sweep=auto, Detector function=peak, Trace=max hold; If the emission level of the EUT measured by the peak detector is 3 dB lower than the applicable limit, the peak emission level will be reported. Otherwise, the emission measurement will be repeated using the quasi-peak detector and reported. (3) From 1 GHz to 10th harmonic: RBW=1MHz, VBW=3MHz Peak detector for Peak value. RBW=1MHz, VBW=3MHz RMS detector for Average value. CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 15 of 29 Report No.: GTI20191250E-2 Test Mode Please refer to the clause 1.7. Test Result 9KHz~0.15MHz Ant. Pol. Horizontal Remarks: 1.Factor (dB/m) = Antenna Factor (dB/m)+Cable Factor (dB)-Pre-amplifier Factor 2.Margin value = Level -Limit value CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 16 of 29 Report No.: GTI20191250E-2 Ant. Pol. Vertical Remarks: 1.Factor (dB/m) = Antenna Factor (dB/m)+Cable Factor (dB)-Pre-amplifier Factor 2.Margin value = Level -Limit value CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 17 of 29 Report No.: GTI20191250E-2 0.15MHz~30MHz Ant. Pol. Horizontal Remarks: 1.Factor (dB/m) = Antenna Factor (dB/m)+Cable Factor (dB)-Pre-amplifier Factor 2.Margin value = Level -Limit value CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 18 of 29 Report No.: GTI20191250E-2 Ant. Pol. Vertical Remarks: 1.Factor (dB/m) = Antenna Factor (dB/m)+Cable Factor (dB)-Pre-amplifier Factor 2.Margin value = Level -Limit value CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 19 of 29 Report No.: GTI20191250E-2 30MHz-1GHz Ant. Pol. Horizontal Remarks: 1.Factor (dB/m) = Antenna Factor (dB/m)+Cable Factor (dB)-Pre-amplifier Factor 2.Margin value = Level -Limit value CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 20 of 29 Report No.: GTI20191250E-2 Ant. Pol. Vertical Remarks: 1.Factor (dB/m) = Antenna Factor (dB/m)+Cable Factor (dB)-Pre-amplifier Factor 2.Margin value = Level -Limit value CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 21 of 29 Report No.: GTI20191250E-2 2.3. Occupied Bandwidth 20 dB Bandwidth Limit FCC CFR Title 47 Part 15 Subpart C Section 15.215 Intentional radiators must be designed to ensure that the 20dB emission bandwidth in the specific band. Test Configuration Test Procedure 1. The EUT was directly connected to the spectrum analyzer and antenna output port as show in the block diagram above. 2. Spectrum Setting: (1) Set RBW ≥ 1% of the 20 dB bandwidth. (2) Set the video bandwidth (VBW) ≥ RBW. (3) Detector = Peak. (4) Trace mode = Max hold. (5) Sweep = Auto couple. Test Mode Please refer to the clause 1.7. Test Results CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 22 of 29 Report No.: GTI20191250E-2 Channel Occupied Bandwidth 20dB Bandwidth Result Frequency(kHz) (kHz) (kHz) 125 6.686 7.757 PASS CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 23 of 29 Report No.: GTI20191250E-2 2.4. Field Strength of the Fundamental Limit FCC CFR Title 47 Part 15 Subpart C Section 15.209 Limit for frequency below 30MHz: Measurement Frequency Limit (uV/m) Remark Distance(m) 0.009~0.490 2400/F(kHz) 300 Quasi-peak 0.490~1.705 24000/F(kHz) 30 Quasi-peak 1.705~30.0 30 30 Quasi-peak Note: Limit dBuV/m @3m = Limit dBuV/m @300m + 40*log(300/3)= Limit dBuV/m @300m +80, Limit dBuV/m @3m = Limit dBuV/m @30m +40*log(30/3)= Limit dBuV/m @30m + 40. Test Configuration Below 30MHz Test Setup Test Procedure 1. The EUT was setup and tested according to ANSI C63.10:2013 requirements. 2. The EUT is placed on a turn table which is 0.8 meter above ground. The turn table is rotated 360 degrees to determine the position of the maximum emission level. 3. The EUT was positioned such that the distance from antenna to the EUT was 3 meters. 4. The antenna is scanned from 1 meter to 4 meters to find out the maximum emission level. This is repeated for both horizontal and vertical polarization of the antenna. In order to find the maximum emission, all of the interface cables were manipulated according to ANSI C63.10:2013 on radiated measurement. Test Mode Please refer to the clause 1.7. CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 24 of 29 Report No.: GTI20191250E-2 Test Result Ant. Pol. Horizontal Emission Level= Read Level+ Correct Factor CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 25 of 29 Report No.: GTI20191250E-2 Ant. Pol. Vertical Emission Level= Read Level+ Correct Factor CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn

Page 26 of 29 Report No.: GTI20191250E-2 2.5. Antenna requirement Requirement FCC CFR Title 47 Part 15 Subpart C Section 15.203: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. Refer to statement below for compliance. The manufacturer may design the unit so that the user can replace a broken antenna, but the use of a standard antenna jack or electrical connector is prohibited. Further, this requirement does not apply to intentional radiators that must be professionally installed. The directional gain of the antenna less than 6dBi, please refer to the EUT internal photographs antenna photo. CTC Laboratories, Inc. 2/F., Building 1 and 1-2/F., Building 2, Jiaquan Building, Guanlan High-Tech Park, Longhua District, Shenzhen, Guangdong, China Tel.: (86)755-27521059 Fax: (86)755-27521011 Http://www.sz-ctc.org.cn For anti-fake verification, please visit the official website of Certification and Accreditation Administration of the People’s Republic of China : http://yz.cnca.cn


Document Created: 2019-07-29 10:07:03
Document Modified: 2019-07-29 10:07:03
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC