Test Report BT Classics

FCC ID: 2APP6AG-26A

Test Report

Download: PDF

FCCID_4225500

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2APP6AG-26A Report No.: LCS190214026AEA

FCC TEST REPORT
FOR
Aroma Music Co., Ltd.
ACOUSTIC GUITAR AMP
Test Model: AG-26A

Additional Model No.: /

Prepared for : Aroma Music Co., Ltd.
Floor 6, Building 56 Baotian Industry Zone, Baotian 3 Road Bao
Address :
An District, Shenzhen 518102 China

Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd.
1/F., Xingyuan Industrial Park, Tongda Road, Bao'an Avenue,
Address :
Bao'an District, Shenzhen, Guangdong, China
Tel : (+86)755-82591330
Fax : (+86)755-82591332
Web : www.LCS-cert.com
Mail : webmaster@LCS-cert.com

Date of receipt of test sample : February 14, 2019
Number of tested samples : 1
Serial number : Prototype
Date of Test : February 14, 2019 ~ March 04, 2019
Date of Report : March 05, 2019

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 1 of 34

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2APP6AG-26A Report No.: LCS190214026AEA

FCC -- TEST REPORT

March 05, 2019
Test Report No. : LCS190214026AEA Date of issue

Type / Model........................... : AG-26A

EUT......................................... : ACOUSTIC GUITAR AMP

Applicant............................... : Aroma Music Co., Ltd.
Floor 6, Building 56 Baotian Industry Zone, Baotian 3 Road Bao An
Address.................................. :
District, Shenzhen 518102 China
Telephone............................... : /
Fax.......................................... : /

Manufacturer........................ : Aroma Music Co., Ltd.
Floor 6, Building 56 Baotian Industry Zone, Baotian 3 Road Bao An
Address................................... :
District, Shenzhen 518102 China
Telephone............................... : /
Fax.......................................... : /

Factory................................... : /
Address................................... : /
Telephone............................... : /
Fax.......................................... : /

Test Result Positive

The test report merely corresponds to the test sample.
It is not permitted to copy extracts of these test result without the written permission of the test laboratory.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 3 of 34

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2APP6AG-26A Report No.: LCS190214026AEA

Revision History
Revision Issue Date Revisions Revised By
000 March 05, 2019 Initial Issue Gavin Liang

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 4 of 34

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2APP6AG-26A Report No.: LCS190214026AEA

TABLE OF CONTENTS

Description Page
1. GENERAL INFORMATION ............................................................................................................ 6
1.1 Description of Device (EUT) ....................................................................................................................... 6
1.2 Support equipment List ............................................................................................................................... 6
1.3 External I/O Cable ........................................................................................................................................ 6
1.4 Description of Test Facility.......................................................................................................................... 6
1.5 Statement of the Measurement Uncertainty ............................................................................................ 7
1.6 Measurement Uncertainty ........................................................................................................................... 7
1.7 Description of Test Modes .......................................................................................................................... 7
2. TEST METHODOLOGY ...................................................................................................................... 8
2.1 EUT Configuration........................................................................................................................................ 8
2.2 EUT Exercise ................................................................................................................................................ 8
2.3 General Test Procedures ............................................................................................................................ 8
2.4. Test Sample ................................................................................................................................................. 8
3. SYSTEM TEST CONFIGURATION .................................................................................................. 9
3.1 Justification.................................................................................................................................................... 9
3.2 EUT Exercise Software ............................................................................................................................... 9
3.3 Special Accessories ..................................................................................................................................... 9
3.4 Block Diagram/Schematics ......................................................................................................................... 9
3.5 Equipment Modifications ............................................................................................................................. 9
3.6 Test Setup ..................................................................................................................................................... 9
4. SUMMARY OF TEST RESULTS..................................................................................................... 10
5. MEASUREMENT RESULTS ............................................................................................................ 11
5.1 Peak Power ................................................................................................................................................. 11
5.2 Frequency Separation and 20dB Bandwidth ......................................................................................... 12
5.3 Number of Hopping Frequency ................................................................................................................ 14
5.4 Time of Occupancy (Dwell Time) ............................................................................................................ 15
5.5 Conducted Spurious Emissions and Band Edges Test ....................................................................... 16
5.6 Restricted Band Emission Limit ............................................................................................................... 17
5.7. AC Power Line Conducted Emissions ................................................................................................... 26
5.8. Band-edge Measurements for Radiated Emissions ............................................................................ 28
5.9. Pseudorandom Frequency Hopping Sequence ................................................................................... 30
5.10. Antenna Requirement ............................................................................................................................ 31
6. SUMMARY OF TEST EQUIPMENT ............................................................................................... 33
7. TEST SETUP PHOTOGRAPHS OF EUT ...................................................................................... 34
8. EXTERIOR PHOTOGRAPHS OF THE EUT ................................................................................. 34
9. INTERIOR PHOTOGRAPHS OF THE EUT .................................................................................. 34

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 5 of 34

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2APP6AG-26A Report No.: LCS190214026AEA

1.5 Statement of the Measurement Uncertainty
The data and results referenced in this document are true and accurate. The reader is cautioned that
there may be errors within the calibration limits of the equipment and facilities. The measurement
uncertainty was calculated for all measurements listed in this test report acc. To CISPR 16 – 4
“Specification for radio disturbance and immunity measuring apparatus and methods – Part 4:
Uncertainty in EMC Measurements” and is documented in the LCS quality system acc. To DIN EN
ISO/IEC 17025. Furthermore, component and process variability of devices similar to that tested may
result in additional deviation. The manufacturer has the sole responsibility of continued compliance of
the device.

1.6 Measurement Uncertainty

Test Item Frequency Range Uncertainty Note
9KHz~30MHz 3.10dB (1)
30MHz~200MHz 2.96dB (1)
Radiation Uncertainty : 200MHz~1000MHz 3.10dB (1)
1GHz~26.5GHz 3.80dB (1)
26.5GHz~40GHz 3.90dB (1)
Conduction Uncertainty : 150kHz~30MHz 1.63dB (1)
Power disturbance : 30MHz~300MHz 1.60dB (1)
(1). This uncertainty represents an expanded uncertainty expressed at approximately the 95%
confidence level using a coverage factor of k=2.

1.7 Description of Test Modes
Bluetooth operates in the unlicensed ISM Band at 2.4GHz. With basic data rate feature, the data rates
can be up to 1 Mb/s by modulating the RF carrier using GFSK techniques. The EUT works in the X-axis,
Y-axis, Z-axis. The following operating modes were applied for the related test items. All test modes
were tested, only the result of the worst case was recorded in the report.

Frequency Range Data Rate
Mode of Operations
(MHz) (Mbps)
2402 1/2
BT V4.2 2441 1/2
2480 1/2
For Conducted Emission
Test Mode TX Mode
For Radiated Emission
Test Mode TX Mode

Worst-case mode and channel used for 150 KHz-30 MHz power line conducted emissions was the
mode and channel with the highest output power that was determined to be TX (1Mbps).
Worst-case mode and channel used for 9 KHz-1000 MHz radiated emissions was the mode and
channel with the highest output power, that was determined to be TX (1Mbps-Low Channel).
Pre-test AC conducted emission at both voltage AC 120V/60Hz and AC 240V/60Hz, recorded worst
case.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 7 of 34

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2APP6AG-26A Report No.: LCS190214026AEA

2. TEST METHODOLOGY
The tests documented in this report were performed in accordance with ANSI C63.10-2013, FCC CFR
PART 15C 15.207, 15.209, 15.247 and DA 00-705.

2.1 EUT Configuration
The EUT configuration for testing is installed on RF field strength measurement to meet the
Commissions requirement and operating in a manner that intends to maximize its emission
characteristics in a continuous normal application.

2.2 EUT Exercise
The EUT was operated in the normal operating mode for Hopping Numbers and Dwell Time test and a
continuous transmits mode for other tests.
According to its specifications, the EUT must comply with the requirements of the Section 15.207,
15.209, 15.247 under the FCC Rules Part 15 Subpart C.

2.3 General Test Procedures
2.3.1 Conducted Emissions
The EUT is directly placed on the ground. According to the requirements in Section 6.2.1 of ANSI
C63.10-2013 Conducted emissions from the EUT measured in the frequency range between 0.15 MHz
and 30MHz using Quasi-peak and average detector modes.

2.3.2 Radiated Emissions
The EUT is placed on a turntable, which is directly placed on the ground. The turntable shall rotate 360
degrees to determine the position of maximum emission level. EUT is set 3m away from the receiving
antenna, which varied from 1m to 4m to find out the highest emission. And also, each emission was to
be maximized by changing the polarization of receiving antenna both horizontal and vertical. In order to
find out the maximum emissions, exploratory radiated emission measurements were made according to
the requirements in Section 6.3 of ANSI C63.10-2013.

2.4. Test Sample
The application provides 2 samples to meet requirement;

Sample Number Description
Sample 1 Engineer sample – continuous transmit
Sample 2 Normal sample – Intermittent transmit

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 8 of 34

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2APP6AG-26A Report No.: LCS190214026AEA

3. SYSTEM TEST CONFIGURATION

3.1 Justification
The system was configured for testing in a continuous transmits condition.

3.2 EUT Exercise Software
The system was configured for testing in a continuous transmits condition and change test channels by
software (FCCAssist 2.4_v1.0) provided by applicant.

3.3 Special Accessories

Manufacturer Description Model Serial Number Certificate
Lenovo PC B470 -- FCC DOC
Lenovo AC/DC ADAPTER ADP-90DDB -- FCC DOC

3.4 Block Diagram/Schematics
Please refer to the related document.

3.5 Equipment Modifications
Shenzhen LCS Compliance Testing Laboratory Ltd. has not done any modification on the EUT.

3.6 Test Setup
Please refer to the test setup photo.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 9 of 34

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2APP6AG-26A Report No.: LCS190214026AEA

4. SUMMARY OF TEST RESULTS
Applied Standard: FCC Part 15 Subpart C
FCC Rules Description of Test Test Sample Result Remark
Maximum Conducted Output
§15.247(b)(1) Sample 1 Compliant Appendix A.1
Power
§15.247(c) Frequency Separation Sample 1 Compliant Appendix A.3
§15.247(c) 99% and 20dB Bandwidth Sample 1 Compliant Appendix A.2
§15.247(a)(1)(ii) Number Of Hopping Frequency Sample 2 Compliant Appendix A.4
Time Of Occupancy
§15.247(a)(1)(iii) Sample 2 Compliant Appendix A.5
(Dwell Time)
§15.209,
Radiated Spurious Emissions Sample 1 Compliant Note 1
§15.247(d)
§15.209, Appendix A.6
Conducted Spurious Emissions Sample 1 Compliant
§15.247(d) Appendix A.7
§15.205 Emissions at Restricted Band Sample 1 Compliant Appendix A.8
§15.207(a) AC Mains Conducted Emissions Sample 1 Compliant Note 1
§15.203 Antenna Requirements Sample 1 Compliant Note 1
§15.247(i)§2.1093 RF Exposure N/A Compliant Note 2

Remark:
Note 1 --- Test results inside test report.
Note 2 --- Test results in other test report (RF Exposure Evaluation).

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 10 of 34

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2APP6AG-26A Report No.: LCS190214026AEA

5.2.4.2 Frequency Separation

PASS
Please refer to Appendix A.3

Remark:
1. Test results including cable loss;
2. Measured at difference Packet Type for each mode and recorded worst case for each mode.
3. Worst case data at DH5 for GFSK, 2DH5 for π/4-DQPSK modulation type;

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 13 of 34

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2APP6AG-26A Report No.: LCS190214026AEA

Receiver Parameter Setting
Attenuation Auto
Start ~ Stop Frequency 9kHz~150kHz / RB/VB 200Hz/1KHz for QP/AVG
Start ~ Stop Frequency 150kHz~30MHz / RB/VB 9kHz/30KHz for QP/AVG
Start ~ Stop Frequency 30MHz~1000MHz / RB/VB 120kHz/1MHz for QP

5.6.3. Test Procedures

1) Sequence of testing 9 kHz to 30 MHz

Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or described
by manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 0.8 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions.
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.

Premeasurement:
--- The turntable rotates from 0° to 315° using 45° steps.
--- The antenna height is 0.8 meter.
--- At each turntable position the analyzer sweeps with peak detection to find the maximum of all
emissions

Final measurement:
--- Identified emissions during the premeasurement the software maximizes by rotating the turntable
position (0° to 360°) and by rotating the elevation axes (0° to 360°).
--- The final measurement will be done in the position (turntable and elevation) causing the highest
emissions with QPK detector.
--- The final levels, frequency, measuring time, bandwidth, turntable position, correction factor, margin
to the limit and limit will be recorded. Also a plot with the graph of the premeasurement and the limit will
be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 18 of 34

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2APP6AG-26A Report No.: LCS190214026AEA

2) Sequence of testing 30 MHz to 1 GHz

Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or described
by manufacturer.
--- If the EUT is a tabletop system, a table with 0.8 m height is used, which is placed on the ground
plane.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.

Premeasurement:
--- The turntable rotates from 0° to 315° using 45° steps.
--- The antenna is polarized vertical and horizontal.
--- The antenna height changes from 1 to 3 meter.
--- At each turntable position, antenna polarization and height the analyzer sweeps three times in peak
to find the maximum of all emissions.

Final measurement:
--- The final measurement will be performed with minimum the six highest peaks.
--- According to the maximum antenna and turntable positions of premeasurement the software
maximize the peaks by changing turntable position (± 45°) and antenna movement between 1 and 4
meter.
--- The final measurement will be done with QP detector with an EMI receiver.
--- The final levels, frequency, measuring time, bandwidth, antenna height, antenna polarization,
turntable angle, correction factor, margin to the limit and limit will be recorded. Also a plot with the graph
of the premeasurement with marked maximum final measurements and the limit will be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 19 of 34

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2APP6AG-26A Report No.: LCS190214026AEA

3) Sequence of testing 1 GHz to 18 GHz

Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or described
by manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 1.5 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.

Premeasurement:
--- The turntable rotates from 0° to 315° using 45° steps.
--- The antenna is polarized vertical and horizontal.
--- The antenna height scan range is 1 meter to 2.5 meter.
--- At each turntable position and antenna polarization the analyzer sweeps with peak detection to find
the maximum of all emissions.

Final measurement:
--- The final measurement will be performed with minimum the six highest peaks.
--- According to the maximum antenna and turntable positions of premeasurement the software
maximize the peaks by changing turntable position (± 45°) and antenna movement between 1 and 4
meter. This procedure is repeated for both antenna polarizations.
--- The final measurement will be done in the position (turntable, EUT-table and antenna polarization)
causing the highest emissions with Peak and Average detector.
--- The final levels, frequency, measuring time, bandwidth, turntable position, EUT-table position,
antenna polarization, correction factor, margin to the limit and limit will be recorded. Also a plot with the
graph of the premeasurement with marked maximum final measurements and the limit will be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 20 of 34

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2APP6AG-26A Report No.: LCS190214026AEA

4) Sequence of testing above 18 GHz

Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or described
by manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 1.5 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 1 meter.
--- The EUT was set into operation.

Premeasurement:
--- The antenna is moved spherical over the EUT in different polarizations of the antenna.

Final measurement:
--- The final measurement will be performed at the position and antenna orientation for all detected
emissions that were found during the premeasurements with Peak and Average detector.
--- The final levels, frequency, measuring time, bandwidth, correction factor, margin to the limit and limit
will be recorded. Also a plot with the graph of the premeasurement and the limit will be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 21 of 34

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2APP6AG-26A Report No.: LCS190214026AEA

5.6.8. Results of Radiated Emissions (1 GHz~26 GHz)

Note: All the modes have been tested and recorded worst mode in the report.

The worst test result for GFSK, Channel 0 / 2402 MHz
Ant. Pre. Cab.
Freq. Reading Measured Limit Margin
Fac Fac. Loss Remark Pol.
MHz dBuV dBuV/m dBuV/m dB
dB/m dB dB
4804.00 56.41 33.06 35.04 3.94 58.37 74.00 -15.63 Peak Horizontal
4804.00 40.81 33.06 35.04 3.94 42.77 54.00 -11.23 Average Horizontal
4804.00 51.81 33.06 35.04 3.94 53.77 74.00 -20.23 Peak Vertical
4804.00 42.82 33.06 35.04 3.94 44.78 54.00 -9.22 Average Vertical
The worst test result for GFSK, Channel 39 / 2441 MHz
Ant. Pre. Cab.
Freq. Reading Measured Limit Margin
Fac Fac. Loss Remark Pol.
MHz dBuV dBuV/m dBuV/m dB
dB/m dB dB
4882.00 57.73 33.16 35.15 3.96 59.70 74.00 -14.30 Peak Horizontal
4882.00 41.36 33.16 35.15 3.96 43.33 54.00 -10.67 Average Horizontal
4882.00 53.17 33.16 35.15 3.96 55.14 74.00 -18.86 Peak Vertical
4882.00 40.89 33.16 35.15 3.96 42.86 54.00 -11.14 Average Vertical
The worst test result for GFSK, Channel 78 / 2480 MHz
Ant. Pre. Cab.
Freq. Reading Measured Limit Margin
Fac Fac. Loss Remark Pol.
MHz dBuV dBuV/m dBuV/m dB
dB/m dB dB
4960.00 53.93 33.26 35.14 3.98 56.03 74.00 -17.97 Peak Horizontal
4960.00 42.38 33.26 35.14 3.98 44.48 54.00 -9.52 Average Horizontal
4960.00 50.61 33.26 35.14 3.98 52.71 74.00 -21.29 Peak Vertical
4960.00 37.47 33.26 35.14 3.98 39.57 54.00 -14.43 Average Vertical

Notes:
1). Measuring frequencies from 9 KHz - 10th harmonic (ex. 26GHz), No emission found between lowest
internal used/generated frequency to 30 MHz.
2). Radiated emissions measured in frequency range from 9 KHz - 10th harmonic (ex. 26GHz) were made
with an instrument using Peak detector mode.
3). 18~25GHz at least have 20dB margin. No recording in the test report.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 25 of 34

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2APP6AG-26A Report No.: LCS190214026AEA

7. Add the maximum transmit antenna gain (in dBi) to the measured output power level to determine the
EIRP level (see 12.2.5 for guidance on determining the applicable antenna gain)
8. Add the appropriate maximum ground reflection factor to the EIRP level (6 dB for frequencies ≤ 30 MHz,
4.7 dB for frequencies between 30 MHz and 1000 MHz, inclusive and 0 dB for frequencies > 1000 MHz).
9. For devices with multiple antenna-ports, measure the power of each individual chain and sum the EIRP
of all chains in linear terms (e.g., Watts, mW).
10. Compare the resultant electric field strength level to the applicable regulatory limit.
11. Perform radiated spurious emission test duress until all measured frequencies were complete.

5.8.5. Test Results
PASS
Please refer to Appendix A.8

Remark:
1. Measured at difference Packet Type for each mode and recorded worst case for each mode.
2. Worst case data at DH5 for GFSK, 2DH5 for π/4DQPSK modulation type;
3. Measured at Hopping and Non-Hopping mode, recorded worst at Non-Hopping mode.
4. The other emission levels were very low against the limit.
5. The average measurement was not performed when the peak measured data under the limit of average
detection.
6. Detector AV is setting spectrum/receiver. RBW=1MHz/VBW=330Hz/Sweep time=Auto/Detector=Peak;
7. Since the out-of-band characteristics of the EUT transmit antenna will often be unknown, the use of a
conservative antenna gain value is necessary. Thus, when determining the EIRP based on the measured
conducted power, the upper bound on antenna gain for a device with a single RF output shall be selected
as the maximum in-band gain of the antenna across all operating bands, or 2 dBi, whichever is greater.
However, for devices that operate in multiple frequency bands while using the same transmit antenna,
the highest gain of the antenna within the operating band nearest in frequency to the restricted band
emission being measured may be used in lieu of the overall highest gain when the emission is at a
frequency that is within 20 percent of the nearest band edge frequency, but in no case shall a value less
than 2 dBi be used.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 29 of 34

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2APP6AG-26A Report No.: LCS190214026AEA

Limits

FCC ISED
Antenna Gain
6 dBi

lowest channel middle channel highest channel
Tnom Vnom
2402 MHz 2441 MHz 2480 MHz
Conducted power [dBm]
Measured with -5.947 -5.363 -5.450
GFSK modulation
Radiated power [dBm]
Measured with -6.918 -6.025 -6.832
GFSK modulation
Gain [dBi] Calculated -0.971 -0.662 -1.382

Measurement uncertainty ± 1.6 dB (cond.) / ± 3.8 dB (rad.)

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 32 of 34

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2APP6AG-26A Report No.: LCS190214026AEA

7. TEST SETUP PHOTOGRAPHS OF EUT

Please refer to separated files for Test Setup Photos of the EUT.

8. EXTERIOR PHOTOGRAPHS OF THE EUT

Please refer to separated files for External Photos of the EUT.

9. INTERIOR PHOTOGRAPHS OF THE EUT

Please refer to separated files for Internal Photos of the EUT.

----------------THE END OF TEST REPORT---------------

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 34 of 34

Document Created: 2019-04-03 13:42:51
Document Modified: 2019-04-03 13:42:51

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC