RF Exposure Info

FCC ID: 2APLME3726

RF Exposure Info

Download: PDF
FCCID_3900778

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. 588 West Jindu Road, Xinqiao, Songjiang, 201612 Shanghai, China Telephone: +86 (0) 21 6191 5666 Fax: +86 (0) 21 6191 5678 Report No.: SHEM180300190103 ee.shanghai@sgs.com Page: 1 of 8 1 Cover Page RF Exposure REPORT Application No.: SHEM1803001901CR Applicant: HAPE INTERNATIONAL (NINGBO) LTD FCC ID: 2APLME3726 IC: 23809-E3726 Equipment Under Test (EUT): NOTE: The following sample(s) submitted was/were identified on behalf of the client as Product Name: Remote Control Engine Model No.(EUT): E3726 Standards: FCC Rules 47 CFR §2.1093 KDB 447498 D01 General RF Exposure Guidance v06 Date of Receipt: 2018-04-11 Date of Test: 2018-05-02 to 2018-05-07 Date of Issue: 2018-05-11 Test Result: Pass* **In the configuration tested, the EUT detailed in this report complied with the standards specified above. Parlam Zhan E&E Section Manager The manufacturer should ensure that all products in series production are in conformity with the product sample detailed in this report. If the product in this report is used in any configuration other than that detailed in the report, the manufacturer must ensure the new system complies with all relevant standards. Any mention of SGS International Electrical Approvals or testing done by SGS International Electrical Approvals in connection with, distribution or use of the product described in this report must be approved by SGS International Electrical Approvals in writing. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at http://www.sgs.com/en/Terms-and-Conditions.aspx and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at http://www.sgs.com/en/Terms-and-Conditions/Terms-e-Document.aspx. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to the sample(s) tested and such sample(s) are retained for 30 days only.

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180300190103 Page: 2 of 8 Revision Record Version Description Date Remark 00 Original 2018-05-11 / Authorized for issue by: Vincent Zhu / Project Engineer Parlam Zhan / Reviewer This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction.documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only

SGS—CSTC Standards Technical Services (Shangha) Co., Lid. Repor No: SHENTS0300190103 Pare: 3 ors 2 Contents Page 1 coverrace 20 contenms 3 cenerat inrormamio 31. cuserInrommmon a 32. gevers. DescumoverEU‘T a 13. Deruisoreurt a 34. Tesr Locamon s 35. TesrFowre s a resnsranbarosanp Limits 4.1— FCCRaororequmner roimon exosue uns s 42. 1CReporrequmer nomnonewrommeumns 7 s measumentent ano carcuration. 5.1 Mowmunernsismrrover s 52. RfEwrowneCaicuumon s Ts tciniaes annin ie yBhut e Cw mma es m onusepvntomiat brovamore maune ie envonn neumin nono o fore oo comen neescorsesue onna EenAE Een ensear cedieal Wmmhn uyin aaad e Eehatya ulen m atacos cces mties ons eioan sen e Mieron e Te Gerp ie mniny are nol ononene ons mcomi onies we aranntnmnm n Te CBantnntaeahe intmen n oumcRevoe ceoe Thoue t oninve otmnrcens omaeeons dnmesnco ocms hy cce ie Giniatemie ui bemars on in e on marut i mnpata uncmrnensarienon ma sn y

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180300190103 Page: 4 of 8 3 General Information 3.1 Client Information Applicant: HAPE INTERNATIONAL (NINGBO) LTD Address of Applicant: 9-27 Nanhai Road, Dagang industrial City, Beilun, Ningbo, China Manufacturer: HAPE INTERNATIONAL (NINGBO) LTD Address of Manufacturer: 9-27 Nanhai Road, Dagang industrial City, Beilun, Ningbo, China Factory: HAPPY ARTS&CRAFTS (NINGBO) CO., LTD Address of Factory: 9-27 Nanhai Road, Dagang industrial City, Beilun, Ningbo, China 3.2 General Description of E.U.T. Power supply: DC 3.6V by Built-in lithium-ion polymer battery (400mAh) Supply the EUT with fully charged battery during the testing. Cable: DC Cable 30cm for USB Port 3.3 Details of E.U.T. Antenna Gain 1.2 dBi Antenna Type PIFA Antenna Channel Spacing 1MHz Modulation Type GFSK, π/4DQPSK, 8DPSK Number of Channels 79 Operation Frequency 2402MHz to 2480MHz Spectrum Spread Frequency Hopping Spread Spectrum(FHSS) Technology This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction.documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180300190103 Page: 5 of 8 3.4 Test Location All tests were performed at: SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. 588 West Jindu Road, Xinqiao, Songjiang, 201612 Shanghai, China. Tel: +86 21 6191 5666 Fax: +86 21 6191 5678 3.5 Test Facility The test facility is recognized, certified, or accredited by the following organizations: • CNAS (No. CNAS L0599) CNAS has accredited SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. to ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories (CNAS-CL01 Accreditation Criteria for the Competence of Testing and Calibration Laboratories) for the competence in the field of testing. • NVLAP (Certificate No. 201034-0) SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. is accredited by the National Voluntary Laboratory Accreditation Program(NVLAP). Certificate No. 201034-0. • FCC –Designation Number: CN5033 SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. has been recognized as an accredited testing laboratory. Designation Number: CN5033. Test Firm Registration Number: 479755. • Industry Canada (IC) – IC Assigned Code: 8617A The 3m Semi-anechoic chamber of SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. has been registered by Certification and Engineering Bureau of Industry Canada for radio equipment testing with Registration No.: 8617A-1. • VCCI (Member No.: 3061) The 3m Semi-anechoic chamber and Shielded Room of SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. has been registered in accordance with the Regulations for Voluntary Control Measures with Registration No.: R-3868,C-4336,T-12221,G-10830 respectively. This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction.documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only

SGS—CSTC Standards Technical Services (Shangha) Co., Lid. Repor No: SHEMTS0300190103 Pare: sors 4 Test Standards and Limits 4.1— FCC Radiofrequency radiation exposure limits "The 1:4 and 10.4 SAR test xclusion thresholds for 100 NHz to 6 GHe attest seperation ditences 50 mm are determned by: {(max power of channal)(mintest separtion ditence)H(GHe]] 80 for 14 SAR and s 7.5 for 10.9 extremity SAR, vhere * 1(GHz)isthe RF channoltrenemit froguency in Gz +. Power and dlitence are rounde to he nesrest mW and mm * The resilis rounded to one dacimal Blace fo comparison * 3.0 and 7.5 are reforted to as the nemericthresholds "The tst exclusions are applcable only when the minimum test separationdistance is « 50 mm, and for transmissionfrequencies batween 100 Nz and 6 GHiz. When the minimum test separation «istence is < 5 mm, a ditance of 5 mm according to 4.1 1) is applied to datermine SAR test exclusion For 2.4G bandl dvice,the mt of worsecase is Paus30Dmulo —20°8 faets —a Sotmw Ts tciniaes annin ie yBhut e Cw mma es m onusepvntomiat brovamore maune ie envonn neumin nono o fore oo comen neescorsesue onna EenAE Een ensear cedieal Wmmhn uyin aaad e Eehatya ulen m atacos cces mties ons eioan sen e Mieron e Te Gerp ie mniny are nol ononene ons mcomi onies we aranntnmnm n Te CBantnntaeahe intmen n oumcRevoe ceoe Thoue t oninve otmnrcens omaeeons dnmesnco ocms hy cce ie Giniatemie ui bemars on in e on marut i mnpata uncmrnensarienon ma sn y

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180300190103 Page: 7 of 8 4.2 IC Radiofrequency radiation exposure limits According to RSS-102 section 2.5.1, SAR evaluation is required if the separation distance between the user and/or bystander and the antenna and/or radiating element of the device is less than or equal to 20 cm, except when the device operates at or below the applicable output power level (adjusted for tune-up tolerance) for the specified separation distance MHz 5 10 15 20 25 30 35 40 45 50 mm ≤300 71 101 132 162 193 223 254 284 315 345 450 52 70 88 106 123 141 159 177 195 213 835 17 30 42 55 67 80 92 105 117 130 1900 7 10 18 34 60 99 153 225 316 431 mW 2450 4 7 15 30 52 83 123 173 235 309 3500 2 6 16 32 55 86 124 170 225 290 5800 1 6 15 27 41 56 71 85 97 106 Output power level shall be the higher of the maximum conducted or equivalent isotropically radiated power (e.i.r.p.) source-based, time-averaged output power. For controlled use devices where the 8 W/kg for 1 gram of tissue applies, the exemption limits for routine evaluation are multiplied by a factor of 5. For limb-worn devices where the 10 gram value applies, the exemption limits for routine evaluation in Table 1 are multiplied by a factor of 2.5. If the operating frequency of the device is between two frequencies located in Table 1, linear interpolation shall be applied for the applicable separation distance. For test separation distance less than 5 mm, the exemption limits for a separation distance of 5 mm can be applied to determine if a routine evaluation is required. For 2.4G band device, the limit is Pmax ≤ 4mW This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction.documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only

SGS-CSTC Standards Technical Services (Shanghai) Co., Ltd. Report No.: SHEM180300190103 Page: 8 of 8 5 Measurement and Calculation 5.1 Maximum transmit power The Power Data is based on the RF Test Report SHEM180300190102. Test Data: Test Mode Test Channel Power[dBm] Peak Power (mW) DH5 2402 -1.28 0.74 DH5 2441 -3.42 0.45 DH5 2480 -3.56 0.44 2DH5 2402 -2.92 0.51 2DH5 2441 -2.33 0.58 2DH5 2480 -2.48 0.56 3DH5 2402 -2.88 0.52 3DH5 2441 -2.22 0.60 3DH5 2480 -2.42 0.57 5.2 RF Exposure Calculation The Max Conducted Peak Output Power is 0.74mW. The best case gain of the antenna is 1.2dBi. 1.2dBi logarithmic terms convert to numeric result is nearly 1.32 According to the formula. calculate the EIRP test result: EIRP= P x G = 0.74 mW x 1.32 = 0.98mW < 4mW < 0.926mW So the SAR report is not required. --End of the Report-- This document is issued by the Company subject to its General Conditions of Service printed overleaf, available on request or accessible at www.sgs.com/terms_and_conditions.htm and, for electronic format documents, subject to Terms and Conditions for Electronic Documents at www.sgs.com/terms_e-document.htm. Attention is drawn to the limitation of liability, indemnification and jurisdiction issues defined therein. Any holder of this document is advised that information contained hereon reflects the Company’s findings at the time of its intervention only and within the limits of Client’s instructions, if any. The Company’s sole responsibility is to its Client and this document does not exonerate parties to a transaction from exercising all their rights and obligations under the transaction.documents. This document cannot be reproduced except in full, without prior written approval of the Company. Any unauthorized alteration, forgery or falsification of the content or appearance of this document is unlawful and offenders may be prosecuted to the fullest extent of the law. Unless otherwise stated the results shown in this test report refer only to thesample(s) tested and such sample(s) are retained for 90 days only


Document Created: 2018-06-25 08:45:46
Document Modified: 2018-06-25 08:45:46
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC