User manual

FCC ID: 2APLE18300390

Users Manual

Download: PDF
FCCID_4003489

Wire-Free Camera Quick Start Guide

2

What’s in the box 100% wireless Lithium 123 batteries camera Magnetic wall Mounting mount screw 3

Insert the batteries 1. Unlock the battery 3. Insert two batteries near compartment by sliding and the back of the camera. holding the latch. 2. Slide the battery door back and lift it to open the compartment. 4

4. Insert two batteries near 5. Close the battery door. the compartment hinge. 5

Sync your camera with a base station 1. Bring the camera within one to three feet of the base station. Your base station will look like one of the following. 1’ - 3’ 30 cm - 100 cm Or 1’ - 3’ 30 cm - 100 cm 6

2. Press the Sync button on the side of the base station for two seconds. Release the button. 3. Wait for the sync status LED to blink green. Or 7

4. Press the Sync button on top of the camera for two seconds. 5. Release the button. Note: Cameras must be synced one at a time. 8

A blue LED on the camera blinks slowly when starting the sync process. The blue LED blinks rapidly to confirm sync. The camera is ready for viewing. Note: The LED blinks amber if the sync is not successful. You must repeat the sync process. 9

Add the camera to your Arlo account 1. Launch the Arlo app from your smartphone, log in, and click or tap Add Device. If you are using a computer, visit arlo.netgear.com. 2. Follow the onscreen instructions. 10

You’re done! Your Arlo camera is set up and ready to go. To view useful tutorial videos, find troubleshooting tips, or get support, scan the QR code or navigate in your browser to visit www.arlo.com/support.

©2018 Arlo Technologies, Inc. Arlo, Arlo logo, and Every Angle Covered are trademarks of Arlo Technologies, Inc. Other trademarks are for reference purposes only. Compliance For regulatory compliance information including the EU Declaration of Conformity, visit www.netgear.com/about/regulatory/. Arlo Technologies, Inc. Arlo International, Ltd. 2200 Faraday Ave. Suite 150 Floor 3, Building 3 University Technology Center Carlsbad, CA 92008 USA Curraheen Road, Cork, Ireland August 2018 12

Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Industry Canada statement: This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes : (1) le dispositif ne doit pas produire de brouillage préjudiciable, et (2) ce dispositif doit accepter tout brouillage reçu, y compris un brouillage susceptible de provoquer un fonctionnement indésirable. Radiation Exposure Statement: This This equipment equipmentcomplies complieswith ISED with radiation ISED exposure radiation limits limits exposure set forth setforforth an uncontrolled for an environment. This equipment should be installed and operated with greater than 20cm uncontrolled between environment. the radiator & your This body.equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Déclaration d'exposition aux radiations: Cet équipement Déclaration est conforme d'exposition aux limites d'exposition aux rayonnements ISED établies aux radiations: pour un environnement non contrôlé. Cet équipement doit être installé et utilisé à plus de Cetcméquipement 20 est conforme entre le radiateur aux limites d'exposition aux rayonnements ISED et votre corps. établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.


Document Created: 2018-09-06 15:38:12
Document Modified: 2018-09-06 15:38:12
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC