Modular Approval Letter

FCC ID: 2APJ4-SLM756P

Cover Letter(s)

Download: PDF
FCCID_4491824

Company: MeiG Smart Technology Co., Ltd Add: 3/F,No.88,Qinjiang Road,Xuhui District,Shanghai,China. Tel: 021-54278676 Fax: 021-54278679 E-mail: louxinwei@meigsmart.com Applicant MeiG Smart Technology Co., Ltd FCC ID: 2APJ4-SLM756P Section 15.212 Modular Transmitters Request for Modular Approval  Request for Limited Modular Approval   Requirements EUT Conditions Comply(Y/N) Single Modular Approval Requirements 1 The radio elements of the modular Refer to external photos. Y transmitter must have their own shielding. This module does have The physical crystal and tuning capacitors shield cover. may be located external to the shielded radio elements. 2 The modular transmitter must have All inputs to the modules Y buffered modulation/data inputs (if such are buffered through logic inputs are provided) to ensure that the or microprocessor inputs. module will comply with part 15 Refer to Schematics. requirements under conditions of excessive data rates or over‐modulation. 3 The modular transmitter must have The Module uses the chip Y MSM8909 with built-in power its own power supply regulation. management components, the module reted power is 3.8V power, Refer to schematics. 4 The modular transmitter must comply The EUT have an antenna for Y with the antenna and transmission system Bluetooth,BLE,Wi-Fi,the antenna is 0.0dBi. Comply with requirements of §§15.203, 15.204(b) and the antenna requirement ,refer 15.204(c). The antenna must either be to exteral photo , The maximum permanently attached or employ a antenna gain for LTE: 10dBi@ WCDMA Band II/LTE “unique” antenna coupler (at all Band 2 , 7dBi@ WCDMABand connections between the module and the IV/ LTE Band 4 , 12.92dBi@ antenna, including the cable). The WCDMABand V/ LTE Band 5 ,10.00dBi @LTE Band 7, “professional installation” provision of 13.92dBi @ LTE Band 12/LTE §15.203 is not applicable to modules but Band 17,13.92dBi @ LTE Band can apply to limited modular approvals 13 under paragraph (b) of this section.

5 The modular transmitter must be The modular Y tested in a stand‐alone configuration, transmitter is tested in a i.e., the module must not be inside stand-alone another device during testing for configuration, i.e., the compliance with part 15 module is not be requirements. Unless the transmitter inside another device module will be battery powered, it when testing. must comply with the AC line Please refer to setup conducted requirements found in photo. §15.207. AC or DC power lines and data input/output lines connected to the module must not contain ferrites, unless they will be marketed with the module (see §15.27(a)). The length of these lines shall be the length typical of actual use or, if that length is unknown, at least 10 centimeters to insure that there is no coupling between the case of the module and supporting equipment. Any accessories, peripherals, or support equipment connected to the module during testing shall be unmodified and commercially available (see §15.31(i)). 6 The modular transmitter must be The device Uses a Y equipped with either a permanently permanently affixed label, affixed label or must be capable of refer Label .when the module is installed inside electronically displaying its FCC another device, then the identification number outside of the device into which the module is installed,this exterior label must use wording such as the following: “Contains Transmitter Module FCC ID: 2APJ4-SLM756P” or “Contains FCC ID: 2APJ4-SLM756P”.

7 The modular transmitter must Refer to manual Y comply with any specific rules or operating requirements that ordinarily apply to a complete transmitter and the manufacturer must provide adequate instructions along with the module to explain any such requirements. A copy of these instructions must be included in the application for equipment authorization. 8 The modular transmitter must The EUT comply with Y comply with any applicable RF any applicable RF exposure requirements in its final exposure requirements configuration. in its final configuration. Sincerely, Signature: Typed or Printed Name: Xinwei Lou Title: HW test Leader


Document Created: 2019-10-26 10:00:57
Document Modified: 2019-10-26 10:00:57
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC