Test Report

FCC ID: 2APDTLYNXW11RF

Test Report

Download: PDF
FCCID_4201624

                                                               FCC Test Report

                       Report No.: RF190109D01

                             FCC ID: 2APDTLYNXW11RF

                       Test Model: LYNX-W11RF

                 Received Date: Jan. 9, 2019

                         Test Date: Jan. 14 ~ 23, 2019

                     Issued Date: Mar. 4, 2019


                         Applicant: IONE ELECTRONIC TECHNOLOGY CO., LTD. TAIWAN BRANCH

                           Address: 8F-2, #75, sec 1, Hsin Tai Wu Rd., Hsi Chih District, New Taipei City,
                                    Taiwan, R.O.C (Far East World Center-Bldg.A)



                        Issued By: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch

             Lab Address: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan,
                          R.O.C.
       FCC Registration /
      Designation Number: 198487 / TW2021




This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted
only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this
report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product
unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you
provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided,
however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time
shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific
mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. The report
must not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies.



Report No.: RF190109D01                                              Page No. 1 / 23                                            Report Format Version: 6.1.1


                                                                   Table of Contents
Release Control Record .................................................................................................................................. 3
1         Certificate of Conformity...................................................................................................................... 4
2         Summary of Test Results ..................................................................................................................... 5
    2.1      Measurement Uncertainty ................................................................................................................... 5
    2.2      Modification Record ............................................................................................................................ 5
3         General Information .............................................................................................................................. 6
    3.1      General Description of EUT ................................................................................................................ 6
    3.2      Description of Test Modes ................................................................................................................... 6
    3.2.1    Test Mode Applicability and Tested Channel Detail............................................................................. 7
    3.3      Description of Support Units ............................................................................................................... 8
    3.3.1    Configuration of System under Test .................................................................................................... 8
    3.4      General Description of Applied Standards .......................................................................................... 8
4         Test Types and Results ........................................................................................................................ 9
    4.1      Radiated Emission and Bandedge Measurement............................................................................... 9
    4.1.1    Limits of Radiated Emission and Bandedge Measurement ................................................................ 9
    4.1.2    Test Instruments ................................................................................................................................ 10
    4.1.3    Test Procedures.................................................................................................................................. 11
    4.1.4    Deviation from Test Standard ............................................................................................................. 11
    4.1.5    Test Setup .......................................................................................................................................... 12
    4.1.6    EUT Operating Conditions................................................................................................................. 13
    4.1.7    Test Results ....................................................................................................................................... 14
    4.2      Channel Bandwidth ........................................................................................................................... 20
    4.2.1    Test Setup .......................................................................................................................................... 20
    4.2.2    Test Instruments ................................................................................................................................ 20
    4.2.3    Test Procedure .................................................................................................................................. 20
    4.2.4    Deviation from Test Standard ............................................................................................................ 20
    4.2.5    EUT Operating Condition .................................................................................................................. 20
    4.2.6    Test Results ....................................................................................................................................... 21
5         Pictures of Test Arrangements .......................................................................................................... 22
Appendix – Information of the Testing Laboratories ................................................................................. 23




Report No.: RF190109D01                                              Page No. 2 / 23                                             Report Format Version: 6.1.1


                                              Release Control Record


 Issue No.                Description                                        Date Issued
 RF190109D01              Original release.                                  Mar. 4, 2019




Report No.: RF190109D01                           Page No. 3 / 23      Report Format Version: 6.1.1


1   Certificate of Conformity


            Product: RF 2.4G Optical Mouse

              Brand: iOne

        Test Model: LYNX-W11RF

    Sample Status: Engineering sample

          Applicant: IONE ELECTRONIC TECHNOLOGY CO., LTD. TAIWAN BRANCH

          Test Date: Jan. 14 ~ 23, 2019

         Standards: 47 CFR FCC Part 15, Subpart C (Section 15.249)
                          ANSI C63.10: 2013



The above equipment has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd.,
Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data
evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts
of the measurements of the sample’s RF characteristics under the conditions specified in this report.




     Prepared by :                                                      , Date:          Mar. 4, 2019
                                Annie Chang / Senior Specialist




     Approved by :                                                      , Date:          Mar. 4, 2019
                             Rex Lai / Associate Technical Manager




Report No.: RF190109D01                        Page No. 4 / 23                        Report Format Version: 6.1.1


2     Summary of Test Results


                             47 CFR FCC Part 15, Subpart C (SECTION 15.249)

       FCC
                                Test Item                      Result                Remarks
      Clause
      15.207         AC Power Conducted Emission                N/A     Power supply is 1.5Vdc from battery
      15.215       Channel Bandwidth Measurement
                 Radiated Emission Test
                 Band Edge Measurement
     15.209                                                        Meet the requirement of limit.
                 Limit: 50dB less than the peak
     15.249                                               PASS     Minimum passing margin is
                 value of fundamental frequency or
   15.249 (d)                                                      -12.81dB at 4810.00MHz.
                 meet radiated emission limit in
                 section 15.209
     15.203      Antenna Requirement                      PASS     No antenna connector is used.
Note: Determining compliance based on the results of the compliance measurement, not taking into account
measurement instrumentation uncertainty.



2.1    Measurement Uncertainty
Where relevant, the following measurement uncertainty levels have been estimated for tests performed on
the EUT as specified in CISPR 16-4-2:

                                                                                     Expanded Uncertainty
                   Measurement                                  Frequency
                                                                                          (k=2) (±)
                                                          9kHz ~ 30MHz                     2.38 dB
         Radiated Emissions up to 1 GHz
                                                        30MHz ~ 1000MHz                    5.54 dB
         Radiated Emissions above 1 GHz                    Above 1GHz                      5.48 dB




2.2    Modification Record
There were no modifications required for compliance.




Report No.: RF190109D01                      Page No. 5 / 23                           Report Format Version: 6.1.1


3     General Information
3.1    General Description of EUT

 Product                      RF 2.4G Optical Mouse
 Brand                        iOne
 Test Model                   LYNX-W11RF
 Status of EUT                Engineering sample
 Power Supply Rating          1.5Vdc from battery
 Modulation Type              GFSK
 Operating Frequency          2405MHz ~2470MHz
 Number of Channel            8
 Antenna Type                 PCB antenna with -1.93dBi gain
 Antenna Connector            N/A
 Accessory Device             N/A
 Data Cable Supplied          N/A
Note: The above EUT information is declared by manufacturer and for more detailed features description,
     please refer to the manufacturer's specifications or user's manual.




3.2    Description of Test Modes
8 channels are provided to this EUT:

                 FREQ.                     FREQ.                      FREQ.                        FREQ.
    CHANNEL                 CHANNEL                     CHANNEL                  CHANNEL
                 (MHz)                     (MHz)                      (MHz)                        (MHz)
       1           2405           3         2422               5       2440           7             2460
       2           2413           4         2430               6       2450           8             2470




Report No.: RF190109D01                      Page No. 6 / 23                       Report Format Version: 6.1.1


3.2.1       Test Mode Applicability and Tested Channel Detail

 EUT Configure                           Applicable To
                                                                                                Description
     Mode
                         RE1G       RE<1G            PLC             APCM

        -                  √            √             Note              √        -
              RE1G: Radiated Emission above 1GHz &
Where                                                          RE<1G: Radiated Emission below 1GHz
              Bandedge Measurement
              PLC: Power Line Conducted Emission               APCM: Antenna Port Conducted Measurement
NOTE: No need to concern of Conducted Emission due to the EUT is powered by battery.


 Radiated Emission Test (Above 1GHz):
    Pre-Scan has been conducted to determine the worst-case mode from all possible combinations
    between available modulations, data rates and antenna ports (if EUT with antenna diversity
    architecture).
    Following channel(s) was (were) selected for the final test as listed below.
         EUT Configure Mode                 Available Channel                  Tested Channel             Modulation Type

                     -                            1 to 8                             1, 4, 8                   GFSK


 Radiated Emission Test (Below 1GHz):
    Pre-Scan has been conducted to determine the worst-case mode from all possible combinations
    between available modulations, data rates and antenna ports (if EUT with antenna diversity
    architecture).
    Following channel(s) was (were) selected for the final test as listed below.
         EUT Configure Mode                 Available Channel                  Tested Channel             Modulation Type

                     -                            1 to 8                                1                      GFSK


 Antenna Port Conducted Measurement:
    This item includes all test value of each mode, but only includes spectrum plot of worst value of each
    mode.
    Pre-Scan has been conducted to determine the worst-case mode from all possible combinations
    between available modulations, data rates and antenna ports (if EUT with antenna diversity
    architecture).
    Following channel(s) was (were) selected for the final test as listed below.
         EUT Configure Mode                 Available Channel                  Tested Channel             Modulation Type

                     -                            1 to 8                             1, 4, 8                   GFSK


 Test Condition:
        Applicable To            Environmental Conditions                    Input Power                  Tested By
             RE1G                   23deg. C, 69%RH                           1.5Vdc                      Ian Chang
             RE<1G                   23deg. C, 69%RH                           1.5Vdc                      Ian Chang
             APCM                    25deg. C, 76%RH                           1.5Vdc                     Saxon Lee




Report No.: RF190109D01                                    Page No. 7 / 23                           Report Format Version: 6.1.1


3.3     Description of Support Units

The EUT has been tested as an independent unit without any necessary accessories or support units.



3.3.1    Configuration of System under Test




                                                        EUT




                                            (Powered from battery)




3.4     General Description of Applied Standards


 The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the
 requirements of the following standards:

 FCC Part 15, Subpart C (15.249)
 ANSI C63.10-2013

 All test items have been performed and recorded as per the above standards.




Report No.: RF190109D01                         Page No. 8 / 23                     Report Format Version: 6.1.1


4       Test Types and Results
4.1     Radiated Emission and Bandedge Measurement
4.1.1    Limits of Radiated Emission and Bandedge Measurement


The field strength of emissions from intentional radiators operated within these frequency bands shall comply
with the following

           Fundamental             Field Strength of Fundamental           Field Strength of Harmonics
            Frequency                     (millivolts/meter)                    (microvolts/meter)

          902 ~ 928 MHz                           50                                   500
        2400 ~ 2483.5 MHz                         50                                   500
         5725 ~ 5875 MHz                          50                                   500
          24 ~ 24.25 GHz                         250                                   2500


Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by
at least 50 dB below the level of the fundamental or to the general radiated emission limits as below table,
whichever is the lesser attenuation

             Frequencies                        Field Strength                   Measurement Distance
                (MHz)                         (microvolts/meter)                       (meters)

            0.009 ~ 0.490                        2400/F(kHz)                               300

            0.490 ~ 1.705                        24000/F(kHz)                                30
             1.705 ~ 30.0                              30                                    30
               30 ~ 88                                 100                                    3
              88 ~ 216                                 150                                    3
              216 ~ 960                                200                                    3
             Above 960                                 500                                    3
NOTE:
1.  The lower limit shall apply at the transition frequencies.
2.  Emission level (dBuV/m) = 20 log Emission level (uV/m).
3.  For frequencies above 1000MHz, the field strength limits are based on average detector, however, the
    peak field strength of any emission shall not exceed the maximum permitted average limits, specified
    above by more than 20dB under any condition of modulation.




Report No.: RF190109D01                        Page No. 9 / 23                         Report Format Version: 6.1.1


4.1.2   Test Instruments

     DESCRIPTION &                                                         CALIBRATED          CALIBRATED
                             MODEL NO.                     SERIAL NO.
     MANUFACTURER                                                             DATE                UNTIL
HP Preamplifier                 8447D                      2432A03504      Feb. 21, 2018       Feb. 20, 2019
HP Preamplifier                 8449B                      3008A01201      Feb. 22, 2018       Feb. 21, 2019
MITEQ Preamplifier       AMF-6F-260400-33-8P                 892164        Feb. 21, 2018       Feb. 20, 2019
Agilent TEST RECEIVER          N9038A                      MY51210137      Jun. 19, 2018       Jun. 18, 2019
Schwarzbeck Antenna          VULB 9168                           139       Nov. 26, 2018       Nov. 25, 2019
Schwarzbeck Antenna          VHBA 9123                           480       May 19, 2017        May 18, 2019
Schwarzbeck Horn Antenna     BBHA-9170                           212       Nov. 25, 2018       Nov. 24, 2019
Schwarzbeck Horn Antenna   BBHA 9120-D1                          D130      Nov. 25, 2018       Nov. 24, 2019
ADT. Turn Table                 TT100                            0306           NA                  NA
ADT. Tower                      AT100                            0306           NA                  NA
Software                 Radiated_V7.6.15.9.5                     NA            NA                  NA
SUHNER RF cable
                                SF102                     Cable-CH6-01     Aug. 13, 2018       Aug. 12, 2019
With 4dB PAD
SUHNER RF cable
                                SF102                   Cable-CH8-3.6m     Aug. 13, 2018       Aug. 12, 2019
With 3/4dB PAD
KEYSIGHT MIMO
Powermeasurement Test         U2021XA                     U2021XA-001       Jun. 4, 2018        Jun. 3, 2019
set
KEYSIGHT
                               N9030A                      MY54490260       Aug. 3, 2018        Aug. 2, 2019
Spectrum Analyzer
Loop Antenna EMCI              LPA600                          270         Aug. 11, 2017       Aug. 10, 2019
EMCO Horn Antenna                3115                        00028257      Nov. 25, 2018       Nov. 24, 2019
Highpass filter
                          WHK 3.1/18G-10SS                       SN 8            NA                  NA
Wainwright Instruments
ROHDE & SCHWARZ
                                      FSV40                      101042    Sep. 27, 2018       Sep. 26, 2019
Spectrum Analyzer

 NOTE: 1. The calibration interval of the above test instruments is 12/24 months. And the calibrations are
          traceable to NML/ROC and NIST/USA.
       2. The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of
          emission frequency above 1GHz if tested.
       3. The test was performed in Chamber No. 6.
       4. The Industry Canada Reference No. IC 7450E-6.




Report No.: RF190109D01                       Page No. 10 / 23                        Report Format Version: 6.1.1


4.1.3      Test Procedures

For Radiated emission below 30MHz
 a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter chamber
    room. The table was rotated 360 degrees to determine the position of the highest radiation.
     b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top
        of a variable-height antenna tower.
     c. Parallel, perpendicular, and ground-parallel orientations of the antenna are set to make the measurement.
     d. For each suspected emission, the EUT was arranged to its worst case and the rotatable table was turned
        from 0 degrees to 360 degrees to find the maximum reading.
     e. The test-receiver system was set to Quasi-Peak Detect Function and Specified Bandwidth with
        Maximum Hold Mode.
NOTE:
 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 9kHz at frequency
    below 30MHz.

For Radiated emission above 30MHz
a. The EUT was placed on the top of a rotating table 0.8 meters (for 30MHz ~ 1GHz) / 1.5 meters (for
    above 1GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to
    determine the position of the highest radiation.
b.      The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the
        top of a variable-height antenna tower.
c.      The height of antenna is varied from one meter to four meters above the ground to determine the
        maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to
        make the measurement.
d.      For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned
        to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to
        find the maximum reading.
e.      The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum
        hold mode when the test frequency is below 1 GHz.
f.      The test-receiver system was set to peak and average detect function and specified bandwidth with
        maximum hold mode when the test frequency is above 1 GHz. If the peak reading value also meets
        average limit, measurement with the average detector is unnecessary.

Note:
1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Quasi-
    peak detection (QP) at frequency below 1GHz.
2.      The resolution bandwidth of test receiver/spectrum analyzer is 1 MHz and the video bandwidth is 3 MHz
        for Peak detection (PK) at frequency above 1GHz.
3.      The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and the video bandwidth is ≥ 1/T
        (Duty cycle < 98%) or 10Hz (Duty cycle ≥ 98%) for Average detection (AV) at frequency above 1GHz.
4.      All modes of operation were investigated and the worst-case emissions are reported.


4.1.4      Deviation from Test Standard

     No deviation.




Report No.: RF190109D01                           Page No. 11 / 23                        Report Format Version: 6.1.1


4.1.5   Test Setup

 For Radiated emission below 30MHz


                                                                    1m
           EUT&                        3m
           Support Units

                             Turn Table

              80cm


                                     Ground Plane
                                     Test Receiver




 For Radiated emission 30MHz to 1GHz

                                                       Ant. Tower
                                                                     1-4m
                                                                     Variable
             EUT&
                                          3m
                                           10m
             Support Units

                                 Turn Table

                 80cm


                                       Ground Plane

                                       Test Receiver




Report No.: RF190109D01                 Page No. 12 / 23                 Report Format Version: 6.1.1


 For Radiated emission above 1GHz



                                                 Ant. Tower             1-4m
                                                                        Variable
 EUT&                               3m
 Support Units

                          Turn Table
                                         Absorber

    150cm


                                 Ground Plane
                                 Test Receiver




 For the actual test configuration, please refer to the attached file (Test Setup Photo).




4.1.6   EUT Operating Conditions

Set the EUT under transmission condition continuously at specific channel frequency.




Report No.: RF190109D01                         Page No. 13 / 23                            Report Format Version: 6.1.1


4.1.7   Test Results
ABOVE 1GHz DATA
 CHANNEL                   TX Channel 1            DETECTOR                 Peak (PK)
 FREQUENCY RANGE           1GHz ~ 25GHz            FUNCTION                 Average (AV)


                   ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
                    EMISSION                          ANTENNA     TABLE        RAW      CORRECTION
        FREQ.                    LIMIT    MARGIN
 NO.                 LEVEL                             HEIGHT     ANGLE       VALUE       FACTOR
        (MHz)                  (dBuV/m)    (dB)
                    (dBuV/m)                             (m)     (Degree)     (dBuV)       (dB/m)
  1      2390.00    55.23 PK     74.00    -18.77        1.31 H     351         56.38        -1.15
  2      2390.00    41.18 AV     54.00    -12.82        1.31 H     351         42.33        -1.15
  3      2400.00    52.47 PK     74.00    -21.53        1.31 H     351         53.62        -1.15
  4      2400.00    28.02 AV     54.00    -25.98        1.31 H     351         29.17        -1.15
  5     *2405.00    93.30 PK    114.00    -20.70        1.31 H     351         94.44        -1.14
  6     *2405.00    68.85 AV     94.00    -25.15        1.31 H     351         69.99        -1.14
  7      4810.00    59.34 PK     74.00    -14.66        2.08 H     16          54.02        5.32
  8      4810.00    34.89 AV     54.00    -19.11        2.08 H     16          29.57        5.32
                    ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
                    EMISSION                          ANTENNA     TABLE        RAW      CORRECTION
        FREQ.                    LIMIT    MARGIN
 NO.                 LEVEL                             HEIGHT     ANGLE       VALUE       FACTOR
        (MHz)                  (dBuV/m)    (dB)
                    (dBuV/m)                             (m)     (Degree)     (dBuV)       (dB/m)
  1      2390.00    54.01 PK     74.00    -19.99        2.82 V     149         55.16        -1.15
  2      2390.00    39.94 AV     54.00    -14.06        2.82 V     149         41.09        -1.15
  3      2400.00    45.18 PK     74.00    -28.82        2.82 V     149         46.33        -1.15
  4      2400.00    20.73 AV     54.00    -33.27        2.82 V     149         21.88        -1.15
  5     *2405.00    86.01 PK    114.00    -27.99        2.82 V     149         87.15        -1.14
  6     *2405.00    61.56 AV     94.00    -32.44        2.82 V     149         62.70        -1.14
  7      4810.00    61.19 PK     74.00    -12.81        1.77 V     263         55.87        5.32
  8      4810.00    36.74 AV     54.00    -17.26        1.77 V     263         31.42        5.32
REMARKS:
   1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
   2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
   3. The other emission levels were very low against the limit.
   4. Margin value = Emission Level – Limit value
   5. " * ": Fundamental frequency.
   6. The average value of fundamental and harmonic frequency is: Average = Peak value + 20 log(Duty
      cycle) Where the duty factor is calculated from following formula:
      20 log(Duty cycle) = 20 log(0.48 ms / 8.01 ms) = -24.45 dB
      Please see page 18 for plotted duty.




Report No.: RF190109D01                    Page No. 14 / 23                       Report Format Version: 6.1.1


 CHANNEL                   TX Channel 4            DETECTOR                 Peak (PK)
 FREQUENCY RANGE           1GHz ~ 25GHz            FUNCTION                 Average (AV)


                  ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
                    EMISSION                          ANTENNA     TABLE        RAW      CORRECTION
        FREQ.                    LIMIT    MARGIN
 NO.                 LEVEL                             HEIGHT     ANGLE       VALUE       FACTOR
        (MHz)                  (dBuV/m)    (dB)
                    (dBuV/m)                             (m)     (Degree)     (dBuV)       (dB/m)
  1    *2430.00     93.07 PK    114.00    -20.93        1.14 H     338         94.16        -1.09
  2    *2430.00     68.62 AV     94.00    -25.38        1.14 H     338         69.71        -1.09
  3     4860.00     59.38 PK     74.00    -14.62        1.00 H     197         54.26        5.12
  4     4860.00     34.93 AV     54.00    -19.07        1.00 H     197         29.81        5.12
                    ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
                    EMISSION                          ANTENNA     TABLE        RAW      CORRECTION
        FREQ.                    LIMIT    MARGIN
 NO.                 LEVEL                             HEIGHT     ANGLE       VALUE       FACTOR
        (MHz)                  (dBuV/m)    (dB)
                    (dBuV/m)                             (m)     (Degree)     (dBuV)       (dB/m)
  1    *2430.00     86.00 PK    114.00    -28.00        2.78 V     141         87.09        -1.09
  2    *2430.00     61.55 AV     94.00    -32.45        2.78 V     141         62.64        -1.09
  3     4860.00     60.74 PK     74.00    -13.26        1.74 V     258         55.62        5.12
  4     4860.00     36.29 AV     54.00    -17.71        1.74 V     258         31.17        5.12
REMARKS:
   1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
   2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
   3. The other emission levels were very low against the limit.
   4. Margin value = Emission Level – Limit value
   5. " * ": Fundamental frequency.
   6. The average value of fundamental and harmonic frequency is: Average = Peak value + 20 log(Duty
      cycle) Where the duty factor is calculated from following formula:
      20 log(Duty cycle) = 20 log(0.48 ms / 8.01 ms) = -24.45 dB
      Please see page 18 for plotted duty.




Report No.: RF190109D01                    Page No. 15 / 23                       Report Format Version: 6.1.1


 CHANNEL                   TX Channel 8            DETECTOR                 Peak (PK)
 FREQUENCY RANGE           1GHz ~ 25GHz            FUNCTION                 Average (AV)


                  ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
                    EMISSION                          ANTENNA     TABLE        RAW      CORRECTION
        FREQ.                    LIMIT    MARGIN
 NO.                 LEVEL                             HEIGHT     ANGLE       VALUE       FACTOR
        (MHz)                  (dBuV/m)    (dB)
                    (dBuV/m)                             (m)     (Degree)     (dBuV)       (dB/m)
  1    *2470.00     91.64 PK    114.00    -22.36        1.44 H     352         92.65        -1.01
  2    *2470.00     67.19 AV     94.00    -26.81        1.44 H     352         68.20        -1.01
  3     2483.50     41.81 PK     74.00    -32.19        1.44 H     352         42.79        -0.98
  4     2483.50     17.36 AV     54.00    -36.64        1.44 H     352         18.34        -0.98
  5     4940.00     59.12 PK     74.00    -14.88        1.97 H     20          54.12        5.00
  6     4940.00     34.67 AV     54.00    -19.33        1.97 H     20          29.67        5.00
                    ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
                    EMISSION                          ANTENNA     TABLE        RAW      CORRECTION
        FREQ.                    LIMIT    MARGIN
 NO.                 LEVEL                             HEIGHT     ANGLE       VALUE       FACTOR
        (MHz)                  (dBuV/m)    (dB)
                    (dBuV/m)                             (m)     (Degree)     (dBuV)       (dB/m)
  1    *2470.00     84.33 PK    114.00    -29.67        2.91 V     154         85.34        -1.01
  2    *2470.00     59.88 AV     94.00    -34.12        2.91 V     154         60.89        -1.01
  3     2483.50     34.50 PK     74.00    -39.50        2.91 V     154         35.48        -0.98
  4     2483.50     10.05 AV     54.00    -43.95        2.91 V     154         11.03        -0.98
  5     4940.00     60.24 PK     74.00    -13.76        1.62 V     274         55.24        5.00
  6     4940.00     35.79 AV     54.00    -18.21        1.62 V     274         30.79        5.00
REMARKS:
   1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
   2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
   3. The other emission levels were very low against the limit.
   4. Margin value = Emission Level – Limit value
   5. " * ": Fundamental frequency.
   6. The average value of fundamental and harmonic frequency is: Average = Peak value + 20 log(Duty
      cycle) Where the duty factor is calculated from following formula:
      20 log(Duty cycle) = 20 log(0.48 ms / 8.01 ms) = -24.45 dB
      Please see page 18 for plotted duty.




Report No.: RF190109D01                    Page No. 16 / 23                       Report Format Version: 6.1.1


                                            Dyty Cycle Test Plots




                          20 log(Duty cycle) = 20 log(0.48 ms / 8.01 ms) = -24.45 dB




Report No.: RF190109D01                       Page No. 17 / 23                         Report Format Version: 6.1.1


Below 1GHz Data:
 CHANNEL                   TX Channel 1             DETECTOR
                                                                             Quasi-Peak (QP)
 FREQUENCY RANGE           9kHz ~ 1GHz              FUNCTION


                  ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M
                    EMISSION                           ANTENNA     TABLE        RAW      CORRECTION
        FREQ.                    LIMIT    MARGIN
 NO.                 LEVEL                              HEIGHT     ANGLE       VALUE       FACTOR
        (MHz)                  (dBuV/m)    (dB)
                    (dBuV/m)                              (m)     (Degree)     (dBuV)       (dB/m)
  1      47.12      17.31 QP    40.00      -22.69        1.14 H     360         24.74        -7.43
  2     147.42      17.18 QP    43.50      -26.32        2.85 H     360         24.23        -7.05
  3     320.08      26.15 QP    46.00      -19.85        2.34 H     64          30.85        -4.70
  4     430.32      22.50 QP    46.00      -23.50        2.10 H     59          25.07        -2.57
  5     607.73      25.65 QP    46.00      -20.35        1.91 H     275         24.75        0.90
  6     651.67      26.27 QP    46.00      -19.73        2.21 H     35          24.54        1.73
REMARKS:
   1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
   2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
   3. The other emission levels were very low against the limit.
   4. Margin value = Emission Level – Limit value
   5. The emission levels were very low against the limit of frequency range 9kHz ~ 30MHz :the amplitude
      of spurious emissions attenuated more than 20 dB below the permissible value to be report.




Report No.: RF190109D01                     Page No. 18 / 23                       Report Format Version: 6.1.1


 CHANNEL                   TX Channel 1             DETECTOR
                                                                             Quasi-Peak (QP)
 FREQUENCY RANGE           9kHz ~ 1GHz              FUNCTION


                    ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 3 M
                    EMISSION                           ANTENNA     TABLE        RAW      CORRECTION
        FREQ.                    LIMIT    MARGIN
 NO.                 LEVEL                              HEIGHT     ANGLE       VALUE       FACTOR
        (MHz)                  (dBuV/m)    (dB)
                    (dBuV/m)                              (m)     (Degree)     (dBuV)       (dB/m)
  1      55.85      19.04 QP    40.00      -20.96        1.00 V     252         26.63        -7.59
  2     114.54      17.40 QP    43.50      -26.10        1.00 V     172         27.26        -9.86
  3     172.40      18.17 QP    43.50      -25.33        1.00 V     68          25.76        -7.59
  4     346.32      20.30 QP    46.00      -25.70        1.00 V     103         24.89        -4.59
  5     509.23      22.94 QP    46.00      -23.06        1.00 V     42          24.10        -1.16
  6     619.61      25.22 QP    46.00      -20.78        1.00 V     169         24.02        1.20
REMARKS:
   1. Emission Level(dBuV/m) = Raw Value(dBuV) + Correction Factor(dB/m)
   2. Correction Factor(dB/m) = Antenna Factor(dB/m) + Cable Factor(dB) – Pre-Amplifier Factor(dB)
   3. The other emission levels were very low against the limit.
   4. Margin value = Emission Level – Limit value
   5. The emission levels were very low against the limit of frequency range 9kHz ~ 30MHz :the amplitude
      of spurious emissions attenuated more than 20 dB below the permissible value to be report.




Report No.: RF190109D01                     Page No. 19 / 23                       Report Format Version: 6.1.1


4.2     Channel Bandwidth
4.2.1    Test Setup


                                                                Spectrum
            EUT
                                        Attenuator              Analyzer


4.2.2    Test Instruments

 Refer to section 4.1.2 to get information of above instrument.



4.2.3    Test Procedure

a. Check the calibration of the measuring instrument using either an internal calibrator or a known signal
   from an external generator.
b. Turn on the EUT and connect it to measurement instrument. Then set it to any one convenient frequency
   within its operating range. Set a reference level on the measuring instrument equal to the highest peak
   value.
c. Measure the frequency difference of two frequencies that were attenuated 20dB from the reference level.
   Record the frequency difference as the emission bandwidth.
d. Repeat above procedures until all frequencies measured were complete.



4.2.4    Deviation from Test Standard

 No deviation.



4.2.5    EUT Operating Condition
The software provided by client enabled the EUT to transmit and receive data at lowest, middle and highest
channel frequencies individually.




Report No.: RF190109D01                              Page No. 20 / 23               Report Format Version: 6.1.1


4.2.6   Test Results


              Channel           Frequency (MHz)          20dB Bandwidth (MHz)

                  1                    2405                       2.87
                  4                    2430                       2.88
                  8                    2470                       2.90

                          Spectrum Plot Of Worst Value




Report No.: RF190109D01         Page No. 21 / 23              Report Format Version: 6.1.1


5   Pictures of Test Arrangements


Please refer to the attached file (Test Setup Photo).




Report No.: RF190109D01                       Page No. 22 / 23   Report Format Version: 6.1.1


Appendix – Information of the Testing Laboratories

We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to
provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are FCC
recognized accredited test firms and accredited according to ISO/IEC 17025.

If you have any comments, please feel free to contact us at the following:

 Lin Kou EMC/RF Lab                                     Hsin Chu EMC/RF/Telecom Lab
 Tel: 886-2-26052180                                    Tel: 886-3-6668565
 Fax: 886-2-26051924                                    Fax: 886-3-6668323

 Hwa Ya EMC/RF/Safety Lab
 Tel: 886-3-3183232
 Fax: 886-3-3270892

 Email: service.adt@tw.bureauveritas.com
 Web Site: www.bureauveritas-adt.com

The address and road map of all our labs can be found in our web site also.



--- END ---




Report No.: RF190109D01                        Page No. 23 / 23                  Report Format Version: 6.1.1



Document Created: 2019-03-11 13:40:41
Document Modified: 2019-03-11 13:40:41

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC