15_C111 UserMan-US

FCC ID: 2APCQ-C111

Users Manual

Download: PDF
FCCID_4286610

What is included: Parameters: Features: Product specification: Attentions: Installation: Installation: Installation: FCC Warning: Infrared Sensor This device complies with part 15 of the FCC Rules.Operation is Infrared Sensor Wireless Charger Holder Car holder with wireless charging fuction, charges Wireless holder Wireless Charge Holder your phone conveniently when driving Input voltage DC 5V/9V Input current 2A Please use the product correctly according instructi ons subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this USER MANUAL Infrared sensor wireless Transmitter coil Advanced infrared sensor system. Hold your phone Output power 5W/7.5/10W Frequency 110-205KHZ 4. Connect the other end 7. The clips will open device must accept any interference received, including charger holder Please do not disassemble the product or interference that may cause undesired operation. automatically 1. Insert the ball into the to green (fast charge) automatically when you X1 QC 3.0 car charger throw it to fire and water, to avoid leakage socket at the back of port of car charger, touch the touch sensitive Any Changes or modifications not expressly approved by the Clamp arms opens after touching touch sensitive party responsible for compliance could void the user's authority Input voltage caused by electrical short circuit bracket and tighten insert the charger to car swtich in side edge, take switc in side edge DC 12-24V to operate the equipment. This equipment has been tested and Clamp arms stretchable cigar lighter your phone away range 58-88mm found to comply with the limits for a Class B digital device, pursuant Output Current/voltage 1 Please do not use wireless charger in high Compliant with 5Ｗ/7.5Ｗ/10W charging power, to part 15 of the FCC Rules. These limits are designed to provide QI standrad Output Current/voltage 2 temperature, wet, corrosive environment, to reasonable protection against harmful interference in a residential Harging Indicator : avoid leakage from caused by damaged circuit installation. This equipment generates uses and can radiate radio Turn red when charging Full 360 degrees rotation for perfect viewing angle frequency energy and, if not installed and used in accordance with Air vent mount X1 LED Mode： Please do not put wireless charger close to the instructions, may cause harmful interference to radio Touch sensitive switch Start charging asap as the phone contact with the cards with magnetic stripes or chips (ID card, communications. holder, no need cable anymore 5. The clips will open However, there is no guarantee that interference will not occur in Power-on: Red, blue, red blue light turn on credit card etc.) to avoid demagnetization automatically when the 8. Then close in 1 second a particular installation. If this equipment does cause harmful Infrared Sensor 2. Insert the mount directly QC 3.0 USB car charger included so you can start by turns for once, then off into the car air vent phone is near 2-3 inches automatically interference to radio or television reception, which can be charging readily, with over temperature, over current, Please keep wireless charger at least 20 CM blade from the infrared sensor determined by turning the equipment off and on, the user is Air vent mount over voltage muti-safety protection Standby Mode: Light off distance away from implantable medical device encouraged to try to correct the interference by one or more of Suit different thickness of car air vent blades the following measures: QC3.0 car charger (heart pacemaker, Implantable cochlea etc.) Charging: Red light keeps on, remove the Compatible devices: to avoid potential interferences -Reorient or relocate the receiving antenna. X1 receiver light off and boot into standby mode -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from Work well with: iP XS Max / NOTE 8 / 9 / iP XR / Take your device away when charging, light off Please do safekeeping, do not let your kids that to which the receiver is connected. 2.5-3.5mm 8P / iP XS / iP X / S8 / S9 / iP 8 and boot into standby mode treat wireless charger as toy to avoid unwanted -Consult the dealer or an experienced radio/TV technician for help. When APPLE phone get fully charged, red light accidents The device has been evaluated to meet general RF exposure 3. Intervene USB cable Also work with all other Qi enabled devices 6. Then close in 1 second requirement. The device can be used in portable exposure keeps on The pictures only supplies the reference, please with your car charger condition without restriction. automatically and hold Qi disabled devices with wireless receiver or When SAMSUNG phone get fully charged, blue FCC RF exposure statement: take the actual product as the standard Note: connect to power your phone tightly and USB cable wireless charging case light keeps on start to charge The equipment complies with FCC Radiation exposure limit set QI charger can speed X1 up charging speed forth for uncontrolled environment. Please read the instructions carefully before using. 1.8-2.5mm 1.8mm （Require receiver compliant with WPC Qi FOD warning:Red light keeps flashing This equipment should be installed and operated with minimum standard to match) distance 20cm between the radiator and your body. What is included: Parameters: Features: Product specification: Attentions: Installation: 使用方法： Installation: What is included: Installation: FCC Warning: Infrared Sensor Infrared Sensor Wireless Charger Holder Car holder with wireless charging fuction, charges Wireless holder This device complies with part 15 of the FCC Rules.Operation is Wireless Charge Holder your phone conveniently when driving Input voltage DC 5V/9V Input current 2A Please use the product correctly according instructi ons subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this USER MANUAL Infrared sensor wireless Transmitter coil Advanced infrared sensor system. Hold your phone Output power 5W/7.5/10W Frequency 110-205KHZ 4. Connect the other end 7. The clips will open device must accept any interference received, including charger holder Please do not disassemble the product or interference that may cause undesired operation. automatically 1. Insert the ball into the to green (fast charge) automatically when you X1 QC 3.0 car charger throw it to fire and water, to avoid leakage socket at the back of port of car charger, touch the touch sensitive Any Changes or modifications not expressly approved by the Clamp arms opens after touching touch sensitive bracket and tighten insert the charger to car swtich in side edge, take party responsible for compliance could void the user's authority Input voltage DC 12-24V caused by electrical short circuit Clamp arms stretchable switc in side edge cigar lighter your phone away to operate the equipment. This equipment has been tested and range 58-88mm Output Current/voltage 1 found to comply with the limits for a Class B digital device, pursuant Please do not use wireless charger in high Compliant with 5Ｗ/7.5Ｗ/10W charging power, to part 15 of the FCC Rules. These limits are designed to provide QI standrad Output Current/voltage 2 temperature, wet, corrosive environment, to reasonable protection against harmful interference in a residential Harging Indicator : avoid leakage from caused by damaged circuit installation. This equipment generates uses and can radiate radio Turn red when charging Full 360 degrees rotation for perfect viewing angle frequency energy and, if not installed and used in accordance with Air vent mount X1 LED Mode： Please do not put wireless charger close to the instructions, may cause harmful interference to radio Touch sensitive switch Start charging asap as the phone contact with the cards with magnetic stripes or chips (ID card, communications. holder, no need cable anymore 5. The clips will open However, there is no guarantee that interference will not occur in Power-on: Red, blue, red blue light turn on credit card etc.) to avoid demagnetization automatically when the 8. Then close in 1 second Infrared Sensor 2. Insert the mount directly a particular installation. If this equipment does cause harmful QC 3.0 USB car charger included so you can start by turns for once, then off into the car air vent phone is near 2-3 inches automatically interference to radio or television reception, which can be charging readily, with over temperature, over current, Please keep wireless charger at least 20 CM blade from the infrared sensor determined by turning the equipment off and on, the user is Air vent mount over voltage muti-safety protection Standby Mode: Light off distance away from implantable medical device encouraged to try to correct the interference by one or more of (heart pacemaker, Implantable cochlea etc.) the following measures: QC3.0 car charger Charging: Red light keeps on, remove the Compatible devices: to avoid potential interferences -Reorient or relocate the receiving antenna. X1 receiver light off and boot into standby mode -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from Work well with: iP XS Max / NOTE 8 / 9 / iP XR / Take your device away when charging, light off Please do safekeeping, do not let your kids that to which the receiver is connected. 8P / iP XS / iP X / S8 / S9 / iP 8 and boot into standby mode treat wireless charger as toy to avoid unwanted -Consult the dealer or an experienced radio/TV technician for help. When APPLE phone get fully charged, red light accidents The device has been evaluated to meet general RF exposure 3. Intervene USB cable Also work with all other Qi enabled devices 6. Then close in 1 second requirement. The device can be used in portable exposure keeps on The pictures only supplies the reference, please with your car charger automatically and hold condition without restriction. Qi disabled devices with wireless receiver or When SAMSUNG phone get fully charged, blue take the actual product as the standard Note: connect to power your phone tightly and FCC RF exposure statement: USB cable wireless charging case light keeps on start to charge QI charger can speed The equipment complies with FCC Radiation exposure limit set X1 Direction applies to 2.5-3.5 mm air vent. up charging speed forth for uncontrolled environment. Please read the instructions carefully before using. （Require receiver compliant with WPC Qi FOD warning:Red light keeps flashing This equipment should be installed and operated with minimum Direction applies to 1.5-2.5 mm air vent: standard to match) distance 20cm between the radiator and your body.


Document Created: 2019-05-07 16:05:13
Document Modified: 2019-05-07 16:05:13
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC