Test Report

FCC ID: 2APC5-WAVE1205

Test Report

Download: PDF
FCCID_4187973

Produkte Products Prüfbericht-Nr.: 50221265 001 Auftrags-Nr.: 114082449 Seite 1 von 32 Test Report No.: Order No.: Page 1 of 32 Kunden-Referenz-Nr.: N/A Auftragsdatum: 03-Oct-2018 Client Reference No.: Order date: Auftraggeber: H.P.B. HI-TECH CORP. Client: 10F., No. 308, Sec. 1, Neihu Rd., Taipei City 114, Taiwan, R.O.C Prüfgegenstand: Test item: Hand Gesture Controller Bezeichnung / Typ-Nr.: Identification / Type No.: Wave1205 Auftrags-Inhalt: FCC Test report (BLE) Order content: Prüfgrundlage: Test specification: FCC 47CFR Part 15: Subpart C Section 15.247(DTS) Wareneingangsdatum: 07-Jan-2019 Date of receipt: Prüfmuster-Nr.: A000863281-001,002 Test sample No.: Prüfzeitraum: 17-Jan-2019 – 26-Jan-2019 Testing period: Ort der Prüfung: EMC/RF Laboratory Taipei Place of testing: Prüflaboratorium: TUV Rheinland Taiwan Ltd. Testing laboratory: Prüfergebnis*: Pass Test result*: geprüft von / tested by: kontrolliert von / reviewed by: 2019.02.27 11:58:24 2019-01-30 Mars Y.J. Lin / Project Engineer 2019-02-22 +08'00' Arvin Ho / Vice General Manager Datum Name / Stellung Unterschrift Datum Name / Stellung Unterschrift Date Name / Position Signature Date Name / Position Signature Sonstiges / Other: Zustand des Prüfgegenstandes bei Anlieferung: Prüfmuster vollständig und unbeschädigt Condition of the test item at delivery: Test item complete and undamaged * Legende: 1 = sehr gut 2 = gut 3 = befriedigend 4 = ausreichend 5 = mangelhaft P(ass) = entspricht o.g. Prüfgrundlage(n) F(ail) = entspricht nicht o.g. Prüfgrundlage(n) N/A = nicht anwendbar N/T = nicht getestet Legend: 1 = very good 2 = good 3 = satisfactory 4 = sufficient 5 = poor P(ass) = passed a.m. test specification(s) F(ail) = failed a.m. test specification(s) N/A = not applicable N/T = not tested Dieser Prüfbericht bezieht sich nur auf das o.g. Prüfmuster und darf ohne Genehmigung der Prüfstelle nicht auszugsweise vervielfältigt werden. Dieser Bericht berechtigt nicht zur Verwendung eines Prüfzeichens. This test report only relates to the a. m. test sample. Without permission of the test center this test report is not permitted to be duplicated in extracts. This test report does not entitle to carry any test mark. TUV Rheinland Taiwan Ltd. 11F., No. 758, Sec. 4, Bade Rd., Taipei 105, Taiwan, R.O.C.

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 2 von 32 Test Report No. Page 2 of 32 TEST SUMMARY 5.1.1 ANTENNA REQUIREMENT RESULT: Passed 5.1.2 PEAK OUTPUT POWER RESULT: Passed 5.1.3 6DB BANDWIDTH RESULT: Passed 5.1.4 POWER DENSITY RESULT: Passed 5.1.5 CONDUCTED SPURIOUS EMISSIONS AND FREQUENCY BAND EDGE MEASURED IN 100KHZ BANDWIDTH RESULT: Passed 5.1.6 SPURIOUS EMISSION RESULT: Passed 5.2.1 MAINS CONDUCTED EMISSIONS RESULT: Passed 6.1.1 ELECTROMAGNETIC FIELDS RESULT: Passed

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 3 von 32 Test Report No. Page 3 of 32 Contents 1. GENERAL REMARKS ............................................................................................... 5 1.1 COMPLEMENTARY MATERIALS ................................................................................. 5 1.2 COMPLEMENTARY MATERIALS ................................................................................. 5 2. TEST SITES ............................................................................................................ 6 2.1 TEST LABORATORY ................................................................................................ 6 2.2 TEST FACILITY........................................................................................................ 6 2.3 LIST OF TEST AND MEASUREMENT INSTRUMENTS...................................................... 7 2.4 TRACEABILITY ........................................................................................................ 8 2.5 CALIBRATION ......................................................................................................... 8 2.6 MEASUREMENT UNCERTAINTY ................................................................................. 8 3. GENERAL PRODUCT INFORMATION ........................................................................... 9 3.1 PRODUCT FUNCTION AND INTENDED USE ................................................................. 9 3.2 SYSTEM DETAILS AND RATINGS ............................................................................... 9 3.3 INDEPENDENT OPERATION MODES ......................................................................... 10 3.4 NOISE GENERATING AND NOISE SUPPRESSING PARTS ............................................ 10 3.5 SUBMITTED DOCUMENTS ....................................................................................... 10 4. TEST SET-UP AND OPERATION MODES ................................................................... 11 4.1 PRINCIPLE OF CONFIGURATION SELECTION ............................................................ 11 4.2 TEST OPERATION AND TEST SOFTWARE................................................................. 11 4.3 SPECIAL ACCESSORIES AND AUXILIARY EQUIPMENT ............................................... 11 4.4 COUNTERMEASURES TO ACHIEVE EMC COMPLIANCE.............................................. 12 4.5 TEST SETUP DIAGRAM .......................................................................................... 12 5. TEST RESULTS ..................................................................................................... 14 5.1 TRANSMITTER REQUIREMENT & TEST SUITES ......................................................... 14 5.1.1 Antenna Requirement ................................................................................................................ 14 5.1.2 Peak Output Power .................................................................................................................... 15 5.1.3 6dB Bandwidth ........................................................................................................................... 16 5.1.4 Power Density ............................................................................................................................ 19 5.1.5 Conducted spurious emissions and Frequency Band Edge measured in 100kHz Bandwidth................................................................................................................................... 22 5.1.6 Spurious Emission ..................................................................................................................... 26 5.2 MAINS EMISSIONS................................................................................................. 27 5.2.1 Mains Conducted Emissions ...................................................................................................... 27 6. SAFETY HUMAN EXPOSURE ................................................................................... 28

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 4 von 32 Test Report No. Page 4 of 32 6.1 RADIO FREQUENCY EXPOSURE COMPLIANCE ......................................................... 28 6.1.1 Electromagnetic Fields ............................................................................................................... 28 7. PHOTOGRAPHS OF THE TEST SET-UP..................................................................... 29 8. LIST OF TABLES ................................................................................................... 32 9. LIST OF PHOTOGRAPHS......................................................................................... 32

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 5 von 32 Test Report No. Page 5 of 32 1. General Remarks 1.1 Complementary Materials These attachments are integral parts of this test report: Appendix P: Photo Documentation internal view (File Name: 50221265 001APPENDIXP) Appendix D: Test Result of Radiated Emissions (File Name: 50221265 001APPENDIXD) Test Specifications The following standards were applied. Table 1: Applied Standard and Test Levels Radio FCC CFR47 Part 15: Subpart C Section 15.247 ANSI C63.10 (2013) KDB558074 D01 15.247 Meas Guidance v05r01 1.2 Complementary Materials The decision rule of conformity of this test report is following the requirements of the requested standard in the quotation, and agreed among testing laboratory and manufacturer (applicant) to exclude the consideration of Measurement Uncertainty, unless it is required by the specific standard.

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 6 von 32 Test Report No. Page 6 of 32 2. Test Sites 2.1 Test Laboratory TUV Rheinland Taiwan Ltd. Taichung Branch Office No.9, Lane 36, Minsheng Rd., Sec. 3, Daya District, Taichung City 428 Taiwan (R.O.C.) 2.2 Test Facility TUV Rheinland Taiwan Ltd. Taipei Office 11F. No.758, Sec. 4, Bade Rd., Songshan Dist. Taipei City 105 Taiwan (R.O.C.) FCC RegistrationNo.: 340738 IC Canada Registration No.: 9465A-1 TAF Accredited NCC Test Lab. No.:0759 TAF ISO17025 Certification effective periods: 2016-Jul-1st to 2019-Jun-30th

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 7 von 32 Test Report No. Page 7 of 32 2.3 List of Test and Measurement Instruments Table 2: List of Test and Measurement Equipment Kind of Last Next Manu-facturer Type S/N Calibration Calibration Equipment Test Software Farad EZ_EMC Ver. TUV3A1 N/A N/A Spectrum R&S FSV 40 100921 2018/05/02 2019/05/01 Analyzer EXA Signal KEYSIGHT N9010A MY52221334 2018/04/05 2019/04/04 Analyzer Preamplifier HP 8447F 2805A03335 2018/08/14 2019/08/13 (30MHz -1GHz) Preamplifier (18 COM- PAM-840 461257 2019/01/18 2020/01/17 GHz -40 GHz) POWER Pre-Amplifier EM EM01G18G 60558 2018/11/21 2019/11/20 (1GHz~18GHz) Electronics Bilog Antenna TESEQ CBL6111D 29804 2018/08/18 2019/08/17 ETS- Horn Antenna 3117 201918 2018/08/18 2019/08/17 Lindgren Horn Antenna COM- AH-840 101029 2018/11/28 2019/11/27 (18GHz~40GHz) POWER Loop Antenna Schwarzbeck FMZB 1513 1513-076 2018/06/14 2019/06/13 EMI Test R&S ESR 7 101549 2018/11/10 2019/11/09 Receiver Spectrum R&S FSL3 101943 2018/09/07 2019/09/06 Analyzer Temp. & Humid. GCT-099- MAF0103- Giant Force 2018/03/09 2019/03/08 Chamber 40-S 007

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 8 von 32 Test Report No. Page 8 of 32 2.4 Traceability All measurement equipment calibrations are traceable to NML(Taiwan)/NIST(USA) or where calibration is performed outside Taiwan, to equivalent nationally recognized standards organizations. 2.5 Calibration Equipment requiring calibration is calibrated periodically in a suitably accredited Calibration Lab. Additionally all equipment is verified for proper performance on a regular schedule using in house standards or comparisons. 2.6 Measurement Uncertainty The estimated combined standard uncertainty for radiated emissions and conducted emissions measurements . Table 3: Emission Measurement Uncertainty Parameter Uncertainty Radio Frequency ± 0.1 ppm RF power, conducted ± 1.5 dB RF power density, conducted ± 3 dB spurious emissions, conducted ± 3 dB all emissions, radiated ± 6 dB Temperature ± 1 ºC Humidity ±5% DC and low frequency voltages ±3 %

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 9 von 32 Test Report No. Page 9 of 32 3. General Product Information 3.1 Product Function and Intended Use The EUT is a Hand Gesture Controller. It contains a Bluetooth compatible module enabling the user to communicate data through a Wireless interface. For details refer to the User Guide, Data Sheet and Block Diagram. 3.2 System Details and Ratings Table 4: Basic Information of EUT Item EUT information Kind of Equipment/Test Item Hand Gesture Controller Type Identification Wave1205 FCC ID 2APC5-WAVE1205 Table 5: Technical Specification of EUT Technical Specification Value Operating Frequencies 2402MHz ~ 2480MHz Channel Spacing 2 MHz Channel number 40 Operation Voltage 5Vdc Modulation GFSK Antenna gain 2.41dBi

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 10 von 32 Test Report No. Page 10 of 32 3.3 Independent Operation Modes Basic operation modes are: A. Transmitting 1. Low channel 2. Middle channel 3. High channel B. Receiving C. Normal 3.4 Noise Generating and Noise Suppressing Parts Refer to the Block Diagram. 3.5 Submitted Documents - Block Diagram - Instruction Manual - Rating Label - Technical Description

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 11 von 32 Test Report No. Page 11 of 32 4. Test Set-up and Operation Modes 4.1 Principle of Configuration Selection The equipment under test (EUT) was configured to measure its maximum power level. The test modes were adapted accordingly in reference to the instructions for use. 4.2 Test Operation and Test Software Setup for testing: Test samples are provided with USB interface which makes it possible to control them through a test software installed on a notebook computer. This software nRFgo was running on the laptop computer connected to the EUT. It was used to enable the operation modes listed in section 3.3 as appropriate. The samples were used as follows: Conducted test: A000863281-001 Radiated test: A000863281-002 Full test was applied on all test modes, but only worst case was shown 4.3 Special Accessories and Auxiliary Equipment The product has been tested together with the following additional accessories: Kind of Equipment Manufacturer Model Name S/N Laptop MSI MSI4532(CX420MX) 1008000096 Fan sensor N/A N/A N/A

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 12 von 32 Test Report No. Page 12 of 32 4.4 Countermeasures to achieve EMC Compliance The test sample which has been tested contained the noise suppression parts as described in the Constructional Data Form or the Technical Construction File. No additional measures were employed to achieve compliance. 4.5 Test Setup Diagram Diagram of Measurement Configuration for Radiation Test Note: Measurements above 1 GHz are done with a table height of 1.5m

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 13 von 32 Test Report No. Page 13 of 32 Diagram of Measurement Equipment Configuration for Mains Conduction Measurement (if applicable) Diagram of Measurement Equipment Configuration for Conducted Transmitter Measurement Test RF Cable Receiver EUT USB Cable NB

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 14 von 32 Test Report No. Page 14 of 32 5. Test Results 5.1 Transmitter Requirement & Test Suites 5.1.1 Antenna Requirement RESULT: Passed Test standard : FCC Part 15.247(b)(4), Part 15.203 Requirement : use of approved antennas only with directional gains that do not exceed 6 dBi According to the manufacturer declaration, the EUT has an antenna with a directional gain of 2.41dBi. The antenna is a Chip Antenna soldered to the PCB with no possibility of replacement with a non- approved antenna by the end-user. Therefore, the EUT is considered to comply with this provision. Refer to EUT photo for details.

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 15 von 32 Test Report No. Page 15 of 32 5.1.2 Peak Output Power RESULT: Passed Test standard : FCC Part 15.247(b)(3) Basic standard : ANSI C63.10 (2013), KDB558074 Limit : 1 Watt Kind of test site : Shielded room Test setup Test Channel : Low/ Middle/ High Operation Mode : A Ambient temperature : 20-24 °C Relative humidity : 50-65 % Atmospheric pressure : 100-103 kPa Table 6: Test result of Peak Output Power Channel Frequency Output Power Limit Channel (MHz) (dBm) (W) (W) Low Channel 2402 -10.16 0.00010 1 Middle Channel 2440 -12.21 0.00006 1 High Channel 2480 -13.69 0.00004 1 Pmax: 0.0964mW

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 16 von 32 Test Report No. Page 16 of 32 5.1.3 6dB Bandwidth RESULT: Passed Test standard : FCC Part 15.247(a)(2) Basic standard : ANSI C63.10 (2013), KDB558074 Kind of test site : Shielded room Test setup Test Channel : Low/ Middle/ High Operation Mode : A Ambient temperature : 20-24°C Relative humidity : 50-65% Atmospheric pressure : 100-103 kPa Table 7: Test result of 6dB Bandwidth Channel 6dB Bandwidth Limit Channel Frequency Result (kHz) (kHz) (MHz) Low Channel 2402 678.3 >500 Pass Mid Channel 2440 696.2 >500 Pass High Channel 2480 701.3 >500 Pass

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 17 von 32 Test Report No. Page 17 of 32 Test Plot of 6dB Bandwidth Low Channel Middle Channel

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 18 von 32 Test Report No. Page 18 of 32 High Channel

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 19 von 32 Test Report No. Page 19 of 32 5.1.4 Power Density RESULT: Passed Test standard : FCC Part 15.247(e) Basic standard : ANSI C63.10 (2013), KDB558074 Kind of test site : Shielded room Test setup Test Channel : Low/ Middle/ High Operation Mode : A Ambient temperature : 20-24°C Relative humidity : 50-65% Atmospheric pressure : 100-103 kPa Table 8: Test result of Power Density Channel Frequency Power Density Limit Channel (MHz) (dBm) (dBm) Low Channel 2402 -23.95 8 Middle Channel 2440 -26.42 8 High Channel 2480 -27.53 8

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 20 von 32 Test Report No. Page 20 of 32 Test Plot of Power Density Low Channel Middle Channel

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 21 von 32 Test Report No. Page 21 of 32 High Channel

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 22 von 32 Test Report No. Page 22 of 32 5.1.5 Conducted spurious emissions and Frequency Band Edge measured in 100kHz Bandwidth RESULT: Passed Test standard : FCC part 15.247(d) Basic standard : ANSI C63.10 (2013), KDB558074 Limit : 20dB (below that in the 100kHz bandwidth within the band that contains the highest level of the desired power) Kind of test site : Shielded room Test setup Test Channel : Low/ Middle/ High for Conducted Spurious Emissions Low/ High for Frequency Band Edge Operation Mode : A Ambient temperature : 20-24°C Relative humidity : 50-65% Atmospheric pressure : 100-103 kPa All emissions are more than 20dB below fundamental, details refer to following test plot, and compliance is achieved as well. Due to the small size of the product and that there are no inductive components of significant size, 9kHz to 30MHz frequency range is not tested based on technical judgment.

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 23 von 32 Test Report No. Page 23 of 32 Test Plot 100kHz Conducted Emissions Low Channel Middle Channel

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 24 von 32 Test Report No. Page 24 of 32 High Channel

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 25 von 32 Test Report No. Page 25 of 32 Test Plot 100kHz RBW of Band Edge Low Channel High Channel

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 26 von 32 Test Report No. Page 26 of 32 5.1.6 Spurious Emission RESULT: Passed Test standard : FCC part 15.247(d), FCC 15.205, FCC 15.209 Basic standard : ANSI C63.10 (2013) Limits : Radiated emissions which fall in the restricted bands, as defined in FCC 15.205(a) and RSS-Gen i5, 8.10 (Table 7), must comply with the radiated emission limits specified in FCC 15.209(a) and RSS-Gen 5, 8.9 (Table 5 and 6). Emission radiated outside the restricted and authorized frequency bands must either comply with the radiated emission limits specified for the restricted bands or in FCC15.247(d) and RSS-247 i2, 5.5 Kind of test site : 3m Semi-Anechoic Chamber Test setup Test Channel : Low/ Middle/ High Operation mode : A,B Factor (dB/m)=Antenna Factor(dB/m)+Cable loss (dB) Level(dBuV/m)=Reading(dBuV)+ Factor(dB/m) Testing was carried out within frequency range 9kHz to the tenth harmonic. For details refer to Appendix D. The Radiated Emissions testing was performed in the X, Y and Z axis orientation. The worst-case Axis orientation is recorded in this test report.

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 27 von 32 Test Report No. Page 27 of 32 5.2 Mains Emissions 5.2.1 Mains Conducted Emissions RESULT: Passed Test standard : FCC Part 15.207 FCC Part 15.107 Limits : Mains Conducted emissions as defined in above test standards must comply with the mains conducted emission limits specified Kind of test site : Shielded Room Test setup Operation mode : C Factor (dB/m)=Antenna Factor(dB/m)+Cable loss (dB) Level(dBuV/m)=Reading(dBuV)+ Factor(dB/m) Remark: For details refer to Appendix D.

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 28 von 32 Test Report No. Page 28 of 32 6. Safety Human exposure 6.1 Radio Frequency Exposure Compliance 6.1.1 Electromagnetic Fields RESULT: Passed Test standard : FCC KDB Publication 447498 D01 v06 FCC: Since maximum peak output power of the transmitter is 0.0964mW < 10mW, hence the EUT is excluded from SAR evaluation according to FCC KDB publication 447498: Mobile Portable RF Exposure

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 29 von 32 Test Report No. Page 29 of 32 7. Photographs of the Test Set-Up Photograph 1: Set-up for Spurious Emissions (Front View) Photograph 2: Set-up for Spurious Emissions (Back View 1)

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 30 von 32 Test Report No. Page 30 of 32 Photograph 3: Set-up for Spurious Emissions (Back View 2) Photograph 4: Set-up for Conducted testing

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 31 von 32 Test Report No. Page 31 of 32 Photograph 5: Set-up for Spurious Emissions, AC Mains (Front View) Photograph 6: Set-up for Spurious Emissions, AC Mains (Back View)

Produkte Products Prüfbericht - Nr.: 50221265 001 Seite 32 von 32 Test Report No. Page 32 of 32 8. List of Tables Table 1: Applied Standard and Test Levels .................................................................................................. 5 Table 2: List of Test and Measurement Equipment ...................................................................................... 7 Table 3: Emission Measurement Uncertainty................................................................................................ 8 Table 4: Basic Information of EUT ................................................................................................................ 9 Table 5: Technical Specification of EUT ....................................................................................................... 9 Table 6: Test result of Peak Output Power ................................................................................................. 15 Table 7: Test result of 6dB Bandwidth ........................................................................................................ 16 Table 8: Test result of Power Density ......................................................................................................... 19 9. List of Photographs Photograph 1: Set-up for Spurious Emissions (Front View)........................................................................ 29 Photograph 2: Set-up for Spurious Emissions (Back View 1) ..................................................................... 29 Photograph 3: Set-up for Spurious Emissions (Back View 2) ..................................................................... 30 Photograph 4: Set-up for Conducted testing ............................................................................................... 30 Photograph 5: Set-up for Spurious Emissions, AC Mains (Front View) ...................................................... 31 Photograph 6: Set-up for Spurious Emissions, AC Mains (Back View) ...................................................... 31


Document Created: 2019-02-27 11:58:24
Document Modified: 2019-02-27 11:58:24
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC