SAR Calibration Report-3

FCC ID: 2AOPD-UT10

RF Exposure Info

Download: PDF
FCCID_4214141

C‘ mm in Collabaration with ETTL 2 \@@ggzgger~ CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing. 100191, China Tel: +86—10—02304033—2079 Fax: +86—10—62304633—2504 E—mail: citl@chinattl.com hitps//wwwchinattl.en Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORMx,y,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques", June 2013 b) IEC 62209—1, "Measurement procedure for assessment of specific absorption rate of human exposure to radio frequency fields from hand—held and body—mounted wireless communication devices— Part 1: Device used next to the ear (Frequency range of 300MHz to 6GHz)", July 2016 c) IEC 62209—2, "Procedure to measure the Specific Absorption Rate (SAR) For wireless communication devices used in close proximity to the human body (frequency range of 30MHz to 6GHz)", March 2010 d) KDB865664, SAR Measurement Requirements for 100 MHz to 6 GHz Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: «_ Measurement Conditions: Further details are available from the Validation Report at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. «_ Antenna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. & Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filled phantom. The impedance stated is transformed from the measurement at the SMA connectorto the feed point. The Return Loss ensures low reflected power. No uncertainty required. & Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. SAR measured: SAR measured at the stated antenna input power. SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. & SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probability of approximately 95%. Certificate No: Z17—9708 1 Page 2 of8

U m * In Collaboration with TTZL, _ CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China tel: +86—10—02304033—2079 Fax: +86—10—02304033—2504 F—mail: ettl@chinattl.com hitp:/iwwwchinattl.cn Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY52 52.10.0.1446 Extrapolation Advanced Extrapolation Phantom Triple Flat Phantom 5.1C Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, de = 5 mm Frequency 1900 MHz & 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 40.0 1.40 mho/m Measured Head TSL parameters (22.0 £ 0.2) °C 40.5 + 6 % 1.39 mhoim + 6 % Head TSL temperature change during test <1.0 °C —— ——— SAR result with Head TSL SAR averaged over 1_cm" _(1 g) of Head TSL Condition SAR measured 250 mW input power 9.88 mW /g SAR for nominal Head TSL parameters normalized to 1W 39.9 mW 1g + 18.8 % (k=2) SAR averaged over 10 cn" (10 g) of Head TSL Condition SAR measured 250 mW input power 5.10 mW /g SAR for nominal Head TSL parameters normalized to 1W 20.5 mW /g 2 18.7 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 53.3 1.52 mhoim Measured Body TSL parameters (22.0 £0.2) °C 53.0 £ 6 % 1.51 mhoim £ 6 % Body TSL temperature change during test <1.0 °C —— SAR result with Body TSL SAR averaged over 1_cm"_(1 g) of Body TSL Condition SAR measured 250 mW input power 9.95 mW /g SAR for nominal Body TSL parameters normalized to 1W 39.9 mW /g £ 18.8 % (k=2) SAR averaged over 10 cn° (10 g) of Body TSL Condition SAR measured 250 mW input power 5.24 mW /g SAR for nominal Body TSL parameters normalized to 1W 21.0 mW /g £ 18.7 % (k=2) Certificate No: 717—9708 1 Page 3 of 8

.@@‘fl m @77TL s_p_e_a_gq .'\' in Collaboration with § S e a Add: No.51 Xueyuan RoadHaidian District, Beijing, 100191, China c 4633—2504 Appendix (Additional assessments outside the scope of CNAS LO0570) Antenna Parameters with Head TSL Impedance, transformed to feed point 49.20+ 5.27;0 Return Loss —2540B Antenna Parameters with Body TSL Impedance, transformed to feed point 46.60+ 4.3210 Return Loss —24.9 dB General Antenna Parameters and Design Electrical Delay (one direction) 1.308 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding lineis directly connected to the second arm of the dipole. The antenna is therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole lengthis still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend or the soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Certificate No: Z17—97081 Page 4 of 8

C mm fi ;Collnborafionewnh 8 l CALIBRATION LABORATORY Add: No.51 Xucyuan Road, Haidian District, I 00191, China Tel: +86—10—62304633—2070 Fax: +86—10—62304633—2504 E—mail: cttt@chinattl.com hitps/wwwchinattlen DASYS Validation Report for Head TSL Date: 06.30.2017 Test Laboratory: CTTL, Beijing, China DUT: Dipole 1900 MHz; Type: D1900V2; Serial: D1900V2 — SN: 50193 Communication System: UID 0, CW: Frequency: 1900 MHz; Duty Cyele: 1:1 Medium parameters used: {= 1900 MHz: 0 = 1.385 S/m; er = 40.51; p = 1000 kg/m3 Phantom section: Left Section Measurement Standard: DASYS (IEEE/IEC/ANS1 €63.19—2007) DASYS Configuration: + Probe: EX3DV4 — SN3617: ConyF(8.26, 8.26, 8.26); Calibrated: 1/23/2017; + Sensor—Surface: 1.4mm (Mechanical Surface Detection) + Electronics: DAE4 Sn1331; Calibrated: 1/19/2017 «+ Phantom: Triple Flat Phantom5.1C; Type: QD 000 P51 CA; Serial: 1161/1 + Measurement SW: DASY52, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) System Performance Check/Zoom Scan(7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 98.36 V/m; Power Drift = 0.00 dB Peak SAR (extrapolated) = 18.9 W/kg SAR(I g)=9.88 W/kg; SAR(1O g) = 5.1 W/kg Maximum value of SAR (measured) = 15.6 W/ke —3.58 447 —10.75 14.34 17.92 0 dB =15.6 W/kg= 11.93 dBW/kg Certificate No: Z17—97081 Page 5 of 8

MH_— fi in Collaboration with \lizzzmyyy»7 CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191 China Tel: +86—10—62304633—2079 Faxc +86—10—62504633—2504 E—mail: etl@chinatt.com hitp/fwwwchinattl.en Impedance Measurement Plot for Head TSL Tri Sif tog wag 10.00de/ mef 0.000de F] 59: °9 rst—1,9000000 onz =25—408 ds 10.00 30.00 20.00 10.00 0.000p —10.00 ~20,00 —30.c0 —40.00 —s0.00 x NiR siz snith (ReJx) scate 1.0000 [Fi oe1] s1 1.9000000 ue 49.102 0. 5.2677 0. 441.26—pH /2 ~ Certificate No: Z17—9708 1 Page 6 of 8

‘@@n_— _i_8 in Collsboration with =7"7}J, a v CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: citl@chinattl.com hitp/www.chinattl.en DASY5 Validation Report for Body TSL Date: 06.30.2017 Test Laboratory: CTTL, Beijing, China DUT: Dipole 1900 MHz; Type: D1900V2; Serial: D1900V2 — SN: 50193 Communication System: UID 0, CW: Frequency: 1900 MHz: Duty Cycle: 1:1 Medium parameters used: £= 1900 MHz: a = 1.509 $/m: &, = 53.02; p = 1000 kg/m‘ Phantom section: Center Section Measurement Standard: DASYS (IEEE/IEC/ANSI €63.19—2007) DASY5 Configuration: * Probe: EX3DV4 — SN3617; ConyF(7.95, 7.95, 7.95); Calibrated: 1/23/2017; + Sensor—Surface: 1.4mm (Mechanical Surface Detection) *« Electronics: DAE4 Sn1331; Calibrated: 1/19/2017 * Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 * Measurement SW: DASYS2, Version 52.10 (0); SEMCAD X Version 14.6.10 (7417) System Performance Check/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Mcasurement grid: dx=5mm, dy=3mm, dz=5mm Reference Value = 97.05 V/m; Power Drift =—0.02 dB Peak SAR (extrapolated) = 18.0 W/kg SAR(I g) =9.95 W/kg; SAR(10 g) = 5.24 W/kg Maximum value of SAR (measured)= 15.3 W/kg dB 0 —3.38 —6.76 410.15 "13.53 416.91 0 dB = 15.3 W/kg = 11.85 dBW/kg Certificate No: 717—9708 1 Page 7 of 8

Report No.: BL-EC1930222-701

® in Collaboration with w UI"’ HBLAH T7 CcaLisraNon LAporatory _aa¥c STY& CNAs Hot Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China ’@‘ CALIBRATION Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 falistubs® CNAS LO570 E—mail: cttl@chinattl.com hitp/fwww.chinattl.en Client baluntek Certificate No: 217—97036 Object D2450V2 — SN: 952 Calibration Procedure(s) FD—211—003—0 CalibrationProcedures for dipole validationkits Calibration date: March 21, 2017 This calibration Certificate documents the traceability to national standards, which realize the physical units of measurements(S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environment temperature(22«3)C and humidity<70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Power Meter NRP2 101919 27—Jun—16 (CTTL, No.J16X04777) Jun—17 Power sensor NRP—Z91 101547 27—Jun—16 (CTTL, No.J16X04777) Jun—17 Reference Probe EX3DV4 SN 3617 23—Jan—17(SPEAG,No.EX3—3617_Jan17) Jan—18 DAE4 SN 777 22—Aug—16(CTTL—SPEAG.No.216—97138) Aug—17 Secondary Standards ID # Cal Date(Calibrated by, Certificate No.) Scheduled Calibration Signal Generator E4438C MY49071430 13—Jan—17 (CTTL, No.J17X00286) Jan—18 Network Analyzer ES071C MY46110673 13—Jan—17 (CTTL, No.J17X00285) Jan—18 Name Function Signature Calibrated by: Zhao Jing SAR Test Engineer Reviewed by: iDianyuan SAR Project Leader _ .:"%> 92 > Approved by: LuBingsong Deputy Director of the laboratory {»T_?Q A ' Issued: March 25, 2 1- This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: Z17—97036 Page 1 of 8

%_7 Add: NS Xueyuan Road,Hhidan Dinic, Bling, 10019 China Tek e ieasieeisa070 Facoteoansoi6s—2s04 Eomaltcttchinat om npshawwchinatien Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORMxy,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2013, "IEEE Recommended Practice for Determining the Peak Spatial—Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques, June2013 b) IEC 62209—1, "Procedure to measure the Specific Absorption Rate (SAR) For hand—held devices used in close proximily to the ear (frequency range of 300MHz to 3GHz)*, February 2005 ) IEC 62200—2, *Procedure to measure the Specific Absorption Rate (SAR) For wireless communication devices used in close proximity to the human body (frequency range of 3OMHz to GGHz)®, March 2010 d) KDBB65G64, SAR Measurement Requirements for 100 MHz to 6 GHz Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: + Measurement Conditions: Further details are available from the Validation Report at the end of the certficate. All figures stated in the certficate are valld at the frequency indicated. +. Anterna Parameters with TSL: The dipole is mounted with the spacer to position its feed point exactly below the center marking of the tfat phantom section, with the arms oriented paraltel to the body axis. +. Feed Point Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid filed phantom. The impedance stated is transformed from the measurement at the SMA connector to the feed point. The Return Loss ensures low reflected power. No uncertainty required. + Electrical Delay: One—way delay between the SMA connector and the antenna feed point, No uncertainty required * SAR measured: SAR measured at the stated antenna input power. * SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector * SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result The reported uncertainty of measurement is stated as the standard uncertainty of Measurement multiplied by the coverage factor k=2, which for a normal distribution Corresponds to a coverage probabiliy of approximately 95% . Centificare No: 217—97036 Page2 ofs

C Add: N1 Xocpun Road, Haidan Disric. Heting 100191; Chioa Tt «4incasomana02 rec ue ioamoiemastt Eomalettchinaleom hophnvoactiation Measurement Conditions DASY system confiuration, as faras notgiven on page 1 DaSY version oasyse sess 12se Extrapolation Advanced Extapotaton Phantom TslFlatPhantom $.1C Distance Dipole Conter— TSL 10 mm wih Spacer Zoom Scan Resolution d«, dy. dz= $ mm Frequency 2450 hes 1 fike Head TSL parameters Te foloning parameters and calculatons were applied Tomporature Pormittvity Conductivity Nominal Head TSL paramotors 220°C 302 180 mhoim Measured Head TSL paramotors @20+02)°C 300 26 % 177 mhoim x 6 % Head TSL temperature change during tost <10°C ~= — SAR result with Head TSL SAR averaged over 1 _cm"_(t g ofHead TSL Condition SAR measured 250 mW nput power 130 mW (g SAR fornorminal Head TSL parametors normalzod to TW $2.4 mW 1g2208 % (ket) SAR averaged over 10 c‘ (109)of Head TS Condition SAR measured 250 mW inut power 5.04 mW ia SAR fornorminaHead TSL parameters normalzed to 1W 24.3 mW 19 204 % (het) Body TSL parameters The folowing parameters and calculaions wore appled Temperature Pormitivity Cenductivity Nominal Body TSL paramotors 220°C 527 195 mhoin Measured Body TL paramotors @20202)°C 52326% 198 mhoim 6 % Body TSL temperature change during test sto°c ~ we SAR result with Body TSL SAR averaged over 1 _cin" (1 g)of Rody TSL Congtion SAR measured 250 mW input power 128 mw/g SAR for nominal Body TSL paramaters normatiznd to 1W 50.5 mW 1g 2 20.% (Ket) SAR averaged over 10 on‘ (10g) of Body TSL Coniton SAR measured 250 mW input power 582 mW io SAR for nominal Body TSparameters nomallzed to TW 23.3 mW i9 204 % (ke) Cenificate No: 217—97036 Pages ofs

C‘ esmm Add: No.31 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com httpy/wwwchinattl.en Appendix (Additional assessments outside the scope of CNAS LO0570) Antenna Parameters with Head TSL Impedance, transformed to feed point 52.00+ 5.940 Return Loss —24.30B Antenna Parameters with Body TSL Impedance, transformed to feed point 48.70+ 6.25]0 Return Loss —23.80B General Antenna Parameters and Design Electrical Delay (one direction) 1.257 ns After long term use with 100W radiated power, only a slight warming of the dipole near the feedpoint can be measured. The dipole is made of standard semirigid coaxial cable. The center conductor of the feeding line is directly connected to the second arm of the dipole. The antennais therefore short—circuited for DC—signals. On some of the dipoles, small end caps are added to the dipole arms in order to improve matching when loaded according to the position as explained in the "Measurement Conditions" paragraph. The SAR data are not affected by this change. The overall dipole length is still according to the Standard. No excessive force must be applied to the dipole arms, because they might bend orthe soldered connections near the feedpoint may be damaged. Additional EUT Data Manufactured by SPEAG Certificate No: Z17—97036 Page 4 of 8

U m in Collaboration with CALIBRATION LABORATORY Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2070 Fax: +86—10—62304633—2504 E—mail: ettl@chinattl.com htpsfwwwchinattl.en DASY5 Validation Report for Head TSL Date: 03.21.2017 Test Laboratory: CTTL, Beijing, China DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 952 Communication System: UID 0, CW; Frequency: 2450 MHz; Duty Cycle: 1:1 Medium parameters used: {= 2450 MHz; a = 1.768 $/m; er= 39.02; p = 1000 kg/m3 Phantom section: Right Section Measurement Standard: DASYS (IEEE/IEC/ANSI €63.19—2007) DASY5 Configuration: «+ Probe: EX3DV4 — SN3617; ConvF(7.74, 7.74, 7.74); Calibrated: 1/23/2017; + Sensor—Surface: 1.4mm (Mechanical Surface Detection) + Electronics: DAE4 $n777; Calibrated: $/22/2016 + Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 + Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7372) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 104.6 V/m; Power Drift = 0.02 dB Peak SAR (extrapolated) = 27.0 W/kg SAR(I g) = 13 W/kg:; SAR(10 g)=6.04 W/kg Maximum value of SAR (measured) =21.7 W/kg ~4.42 —8.84 13.26 —17.68 E. 2210 0 dB =21.7 W/kg =13.36 dBW/kg Certificate No: Z17—97036 Page 5 of 8

Add: No.51 Xueyuan Road, Haidian District, Beijing, 100191, China Tel: +86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitp=//www.chinatl.en Impedance Measurement Plot for Head TSL Tri si1 Log Mag 10.00d8/ ref 0.000d8 Fi] 50.00 >12.4500000 ne —24.261 do «0.00 30. co 20. 00 10.00 0.ccop —20. 00 ~20.00 ~30.00 —40. 00 ~50. 00 MBR S11 snith (ReJ>) scale 1.000u [ ve1] »1. 2.4500000 ane st.9s4 o. s.9372 n 3e5.6 Certificate No: Z17—97036 Page 6 of 8

U m a 86—10—62304633—2079 Fax: +86—10—62304633—2504 E—mail: cttl@chinattl.com hitps/wwwchinatl.en DASYS Validation Report for Body TSL Date: 03.21.2017 Test Laboratory: CTTL, Beijing, China DUT: Dipole 2450 MHz; Type: D2450V2; Serial: D2450V2 — SN: 952 Communication System: UID 0, CW; Frequency: 2450 MHz; Duty Cycle:1:1 Medium parameters used: {= 2450 MHz; a= 1.931 S/m; s, = 52.27; p= 1000 kg/im‘ Phantom section: Center Section Measurement Standard: DASYS (IEEE/IEC/ANSI C63.19—2007) DASY3 Configuration: * Probe: EX3DV4 — SN3617; ConvF(7.8, 7.8, 7.8); Calibrated: 1/23/2017; + Sensor—Surface: 1.4mm (Mechanical Surface Detection) + Electronics: DAE4 Sn777; Calibrated: 8/22/2016 + Phantom: Triple Flat Phantom 5.1C; Type: QD 000 P51 CA; Serial: 1161/1 + Measurement SW: DASY52, Version 52.8 (8); SEMCAD X Version 14.6.10 (7372) Dipole Calibration/Zoom Scan (7x7x7) (7x7x7)/Cube 0: Measurement grid: dx=5mm, dy=5mm, dz=5mm Reference Value = 96.07 V/m; Power Drift =—0.04 dB Peak SAR (extrapolated) = 26.4 W/kg SAR(I g) = 12.6 W/kg; SAR(1O g) = 5.82 Wkg Maximum value of SAR (measured) =20.9 W/kg dB — — _ Te 0 ~4.41 —8.82 "13.22 417.63 k. —22.04 0 dB =20.9 W/kg =13.20 dBW/kg Certificate No: Z17—97036 Page 7 of 8

Report No.: BL-EC1930222-701

Report No.: BL-EC1930222-701 F.8 2600 MHz Dipole

‘.%_— r Calibration Laboratory of Schweizerischer Kaltertonst Schmid & Partner g Sorvice étatonnage Engineering AG Sorvito viezero i trature Zooghausstrasse 43, 0004 2urich, Stzeriand S Swise Gatbration Sevice Accrted by tha Swiss Accredtaton Sovics (8A5) Accrediution .: SCS 0108 The Suiss Aceredation Serice is one ofthesignatoriosto the EA Moitlateral Agreementfor the recogntion of allraioncerilcates Glossary: TSL tissue simulating liquid ConvF sensitivity in TSL / NORM xy,z N/A not applicable or not measured Calibration is Performed According to the Following Standards: a) IEEE Std 1528—2019, ‘IEEE Recommended Practice for Determining the Peak Spatial« Averaged Specific Absorption Rate (SAR) in the Human Head from Wireless Communications Devices: Measurement Techniques®, June 2013 b IEC 62209—1, "Measurement procedure for the assessmentof Specific Absorption Rate (SAR) from hand—held and body—mounted devices used next to the ear (frequency range of 300 MHz to 6 GHz)", July 2016 c IEC 62209—2, "Procedure to determine the Specific Absorption Rate (GAR) for wireless communication devices used in closeproximity to the human body (frequency range of 30 MHz to 6 GHz)®, March 2010 d) KDB 865664, "SAR Measurement Requirements for 100 MHz to 6 GHz" Additional Documentation: e) DASY4/5 System Handbook Methods Applied and Interpretation of Parameters: * Measurement Conditions: Further details are available from the Validation Report at the end of the certficate. All figures stated in the certificate are valid at the frequency indicated. * Antenna Parameters with TSL: The dipole is mounted with the spacer to position ite feed point exactly below the center marking of the flat phantom section, with the arms oriented parallel to the body axis. * FeedPoint Impedance and Return Loss: These parameters are measured with the dipole positioned under the liquid fled phantom. The impedancestated is transformed from the measurement at the SMA connector to the feed point. The Retun Loss ensures low reflected power. No uncertainty required. * Electrical Delay: One—way delay between the SMA connector and the antenna feed point. No uncertainty required. * SAR measured: SAR measured at the stated antenna input power. * SAR normalized: SAR as measured, normalized to an input power of 1 W at the antenna connector. + SAR for nominal TSL parameters: The measured TSL parameters are used to calculate the nominal SAR result. The reported uncertainty of measurementis stated as the standard Uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Corticate No: D26002—1085.Jut? Page 2 0f8

-@@n_ Measurement Conditions DASY system configuration, asfar as not given on page 1. DASY Version DASY5 V52.10.0 Extrapolation Advanced Extrapolation Phantom Modular Flat Phantom Distance Dipole Center — TSL 10 mm with Spacer Zoom Scan Resolution dx, dy, dz =5 mm Frequency 2600 MHz + 1 MHz Head TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Head TSL parameters 22.0 °C 39.0 1.96 mho/m Measured Head TSL parameters (22.0 £ 0.2) °C 87.2 26 % 2.04 mho/m + 6 % Head TSL temperature change during test <0.5 °C «+ sez SAR result with Head TSL SAR averaged over 1 cm* (1 g) of Head TSL Condition SAR measured 250 mW input power 14.5 Wikg SAR for nominal Head TSL parameters normalized to 1W 56.4 W/kg 2 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Head TSL condition SAR measured 250 mW input power 6.40 Wikg SAR for nominal Head TSL parameters normalized to 1W 25.2 Wikg 2 16.5 % (k=2) Body TSL parameters The following parameters and calculations were applied. Temperature Permittivity Conductivity Nominal Body TSL parameters 22.0 °C 52.5 2.16 mho/m Measured Body TSL parameters (22.0 £ 0.2) °C 51.6 + 6 % 2.22 mho/m x 6 % Body TSL temperature change during test <0.5°C —— ——— SAR result with Body TSL SAR averaged over 1 cm‘ (1 g) of Body TSL Condition SAR measured 250 mW input power 13.8 Wikg SAR for nominal Body TSL parameters normalized to 1W 54.3 W/kg 2 17.0 % (k=2) SAR averaged over 10 cm* (10 g) of Body TSL condition SAR measured 250 mW input power 6.15 Wig SAR for nominal Body TSL parameters normalized to 1W 24.4 Wikg 2 16.5 % (k=2) Certificate No: D2600V2—1095_Jul17 Page 3 of 8

&&& Appendix (Additional assessments outside the scope of SCS 0108) Antenna Parameters with Head TSL Impedance,transtormas to faed point ar20—74 j Return Loss —21.008 Antenna Parameters with Body TSL Impedance,transformed to feed point s160—50 j Retur Loss —21508 General Antenna Parameters and Design [ Electrical Detay (one girection} | 1.180 ns Alterlong tarm use with 100W radiated power, only a slght warming of the dipole near the feedpointcan be measured. The dipol is made of standard semrigid coaxial eable. The center condluctor of the feeding e is drectly connected to the second arm ofthe dipole, The antenn is therefore shortcrcuited for DC—signals. On some ofthe cipoles, small end caps are added to the dipole arms in orderto improve matching when loaded according tothe postion as explained in the ‘Measuremont Conditions* paragraph. The SAR data are not affected by ths change. The overallipole length is stll according to the Standard. No excessive force must be applied to the dipole arms, because thay might bend or the soldered connections near the feedpoint may bo damaged. Additional EUT Data Manutactured by sreao Manutactured on October 12, 2016 Gerificare No: Dzs00¥2—1095_Jut? Page 4 ot8

C mm DASYS Validation Report for Head TSL Date: 10.07.2017 Test Laboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2600 MHz: Type: D2600V2; Serial: D260OV2 — SN:1095 Communication System; UID 0 — CW; Frequency: 2600 MHz Mediumparameters used: I‘= 2600 MHz: a =2.04 $/m; £, = 37.2; p = 1000 kg/m‘ Phantomsection: Flat Section Measurement Standard: DASYS (IEEE/IEC/ANSI C63.19—201 1) DASY52 Configuration: * Probe: EX3DV4 SN7349; ConvF(7.96. 7.96, 7.96); Calibrated: 31.05.2017; + Sensor Surface: 1 Amm (Mechanical Surface Detection) + Electronics: DAE4 Sn601; Calibrated: 28.03.2017 + Phantom: Flat Phantom 5.0 (front); Type: QD 000 P50 AA; Serial: 1001 + DASY52 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for Head Tissue/Pi 250 mW, =10mm/Zoom Scan (7x7x7)/Cube 0: Measurement grid: dx=Smm, dy=5mm, de=Smim Reference Value= 114.1 V/m; Power Drift = —0.08 dB Peak SAR (extripolated) 31.2 W/kg SAR(T g) = 14.5 W/kz: SAR(IOg) 6.4 We Maximum value of SAR (measured) = 24.2 We 4n a .00 10.00 +15.00 —20.00 —25.00 0 dB =24.2 W/kg = 13.84 dBW/kg Gerticate No: D2600V2—1095 _Jut? Page S of 8

C mm Impedance Measurement Plot for Head TSL a0 aul meur asisoine tBD sn io rs menaree —rossse anauer 2 go0.000 o0n mz te cne sin uos 5 cerngr ~a0 e m—2u001 on 2 sooe see mz ca ma Stait 2 sonooo o00 mz Stoe 2 son.000 ooo me Conticate No: 2s00v2—1088.lut? Page 6ot 8

C esmm DASY5 Validation Report for Body TSL Date: 10.07.2017 Test Luboratory: SPEAG, Zurich, Switzerland DUT: Dipole 2600 MHz; Type: D260OV2; Serial: D2600V2 — SN:1095 Communication System: UID 0 — CW; Frequen 2600 MHz Medium parameters used: 2600 MHz: S/m; £, = 51.6; p = 1000 ke/m‘ Phantomsection: Flat Section Mcasurement Standard: DASYS (IEEE/IEC/ANSI C63.19—2011) DASY52 Configuration: * Probe: EX3DV4 — SN7349; ConvB(7.94, 7.94, 7.94); Calibrated: 31.05.2017; * Sensor—Surfice: 1.4mm (Mechanical Surface Detection) * Electronics: DAE4 Sn601; Calibrated: 28.03.2017 + Phantom: Flat Phantom 5.0(back);Type: QD 000 PSO AA; Serial: 1002 + DASY32 52.10.0(1446); SEMCAD X 14.6.10(7417) Dipole Calibration for BodyTissue/Pin=250 mW, d=10mm/ZoomScan (7x7x7)/Cube 0: Measurement grid: dx=Smm, dy=5mm, de Reference Value= 103.9 ¥/m; Power Drif Peak SAR (extrapolated) = 28.9 W/kg SARC g) / an o 12.00 16.00 20.00 0 4B =22.1 Whkg= 13444 dBWhke Cortfcate No: D26002—1095_Jutt? Page 7 of8

Report No.: BL-EC1930222-701 ‐‐END OF REPORT‐‐


Document Created: 2019-03-18 12:48:47
Document Modified: 2019-03-18 12:48:47
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC