Test Report

FCC ID: 2AOAF-430

Test Report

Download: PDF
FCCID_4241755

Shenzhen Huaxia Testing Technology Co., Ltd 1F., Block A of Tongsheng Technology Building, Huahui Road, Dalang Street, Longhua District, Shenzhen, China Telephone: +86-755-26648640 Fax: +86-755-26648637 Report Template Version: V03 Website: www.cqa-cert.com Report Template Revision Date: Mar.1st, 2017 Test Report Report No.: CQASZ20190300180E-01 Applicant: TYLT, inc. Address of Applicant: 685 Cochran St. Suite 200, Simi Valley, California 93065, United States Manufacturer: TYLT, inc. Address of 685 Cochran St. Suite 200, Simi Valley, California 93065, United States Manufacturer: Factory: DONGGUAN KINTEC DIGITAL TECHNOLOGY CO.,LIMITED Address of Factory: 8F,JINYE BUILDING,NO.306,CHANGQING SOUTH ROAD,CHANG'AN,DONGGUANG CITY,GUANGDONG,CHINA Equipment Under Test (EUT): Product: Wireless charger Model No.: QITWST360GY-T, 4568L, KQI-S32SM Test Model No.: QITWST360GY-T Brand Name: N/A FCC ID: 2AOAF-430 Standards: 47 CFR Part 15, Subpart C Date of Test: 2019-03-21 to 2019-03-29 Date of Issue: 2019-03-29 Test Result : PASS* Tested By： (Daisy Qin) Reviewed By: (Aaron Ma ) Approved By: ( Jack Ai) * In the configuration tested, the EUT complied with the standards specified above. The test report is effective only with both signature and specialized stamp, The result(s) shown in this report refer only to the sample(s) tested. Without written approval of CQA, this report can’t be reproduced except in full.

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 1 Version Revision History Of Report Report No. Version Description Issue Date CQASZ20190300180E-01 Rev.01 Initial report 2019-03-29 Page:2 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 2 Test Summary Test Item Test Requirement Test method Result 47 CFR Part 15, Subpart C Section Antenna Requirement ANSI C63.10 2013 PASS 15.203 AC Power Line 47 CFR Part 15, Subpart C Section Conducted ANSI C63.10 2013 PASS 15.207 Emission 20dB Occupied 47 CFR Part 15, Subpart C Section ANSI C63.10 2013 PASS Bandwidth 15.215 Radiated Emission , 47 CFR Part 15, Subpart C Section Radiated Spurious ANSI C63.10 2013 PASS 15.209 Emissions Page:3 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 3 Contents Page 1 VERSION .................................................................................................................................................... 2 2 TEST SUMMARY ....................................................................................................................................... 3 3 CONTENTS ................................................................................................................................................ 4 4 GENERAL INFORMATION ........................................................................................................................ 5 4.1 CLIENT INFORMATION.............................................................................................................................. 5 4.2 GENERAL DESCRIPTION OF EUT ............................................................................................................. 5 4.3 TEST ENVIRONMENT ............................................................................................................................... 6 4.4 DESCRIPTION OF SUPPORT UNITS ........................................................................................................... 6 4.5 STATEMENT OF THE MEASUREMENT UNCERTAINTY ................................................................................... 7 4.6 TEST LOCATION ...................................................................................................................................... 7 4.7 TEST FACILITY ........................................................................................................................................ 7 4.8 DEVIATION FROM STANDARDS ................................................................................................................. 7 4.9 OTHER INFORMATION REQUESTED BY THE CUSTOMER ............................................................................. 7 4.10 EQUIPMENT LIST..................................................................................................................................... 8 5 TEST RESULTS AND MEASUREMENT DATA ........................................................................................ 9 5.1 ANTENNA REQUIREMENT......................................................................................................................... 9 5.2 CONDUCTED EMISSIONS ....................................................................................................................... 10 5.3 20DB OCCUPY BANDWIDTH .................................................................................................................. 13 5.4 RADIATED SPURIOUS EMISSION & RESTRICTED BANDS ........................................................................... 15 5.4.1 Spurious Emissions .................................................................................................................... 15 6 PHOTOGRAPHS - EUT TEST SETUP .................................................................................................... 20 6.1 RADIATED EMISSION ............................................................................................................................. 20 6.2 CONDUCTED EMISSION ......................................................................................................................... 21 7 PHOTOGRAPHS - EUT CONSTRUCTIONAL DETAILS ........................................................................ 22 Page:4 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 4 General Information 4.1 Client Information Applicant: TYLT, inc. Address of Applicant: 685 Cochran St. Suite 200, Simi Valley, California 93065, United States Manufacturer: TYLT, inc. Address of Manufacturer: 685 Cochran St. Suite 200, Simi Valley, California 93065, United States Factory: DONGGUAN KINTEC DIGITAL TECHNOLOGY CO.,LIMITED Address of Factory: 8F,JINYE BUILDING,NO.306,CHANGQING SOUTH ROAD,CHANG'AN,DONGGUANG CITY,GUANGDONG,CHINA 4.2 General Description of EUT Product Name: Wireless charger Model No.: QITWST360GY-T, 4568L, KQI-S32SM Test Model No.: QITWST360GY-T Brand Name: N/A Hardware Version: V1.0 Software Version: V1.0 Equipment Category Non-ISM frequency Operation Frequency range 110-205KHz Modulation Type: Induction Antenna Type: Induction coil Antenna Gain: 0dBi EUT Power Supply: DC 5V Note: 1. All model: QITWST360GY-T, 4568L, KQI-S32SM Only the model QITWST360GY-T was tested, since the electrical circuit design, layout, components used and internal wiring were identical for the above models, with difference being color of appearance and model name. 2. In section 15.31(m), regards to the operating frequency range less 1 MHz. Page:5 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 4.3 Test Environment Operating Environment: Temperature: 25.0 C Humidity: 53 % RH Atmospheric Pressure: 1010mbar Test Mode: Mode a: Wireless charging Mode at 5V (Full load) Mode b: Wireless charging Mode at 5V (half load) Mode c: Wireless charging Mode at 5V (Null load) Note: The mode a was the worst case and only the data of the worst case record in this report. 4.4 Description of Support Units The EUT has been tested with associated equipment below. Description Manufacturer Model No. Remark FCC certification Adaptor Samsung EP-TA50CBC Provide by lab Verification Wireless Provide by lab - electronic Load - - Page:6 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 4.5 Statement of the measurement uncertainty The data and results referenced in this document are true and accurate. The reader is cautioned that there may be errors within the calibration limits of the equipment and facilities. The measurement uncertainty was calculated for all measurements listed in this test report acc. to CISPR 16 - 4 „Specification for radio disturbance and immunity measuring apparatus and methods – Part 4: Uncertainty in EMC Measurements“ and is documented in the Shenzhen Huaxia Testing Technology Co., Ltd. quality system acc. to DIN EN ISO/IEC 17025. Furthermore, component and process variability of devices similar to that tested may result in additional deviation. The manufacturer has the sole responsibility of continued compliance of the device. Hereafter the best measurement capability for CQA laboratory is reported: No. Item Uncertainty Notes 1 Radiated Emission (Below 1GHz) ±5.12dB (1) 2 Radiated Emission (Above 1GHz) ±4.60dB (1) 3 Occupied Bandwidth 1.1% (1) 4 Temperature test 0.8℃ (1) 5 Humidity test 2.0% (1) (1)This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. 4.6 Test Location Shenzhen Huaxia Testing Technology Co., Ltd, 1F., Block A of Tongsheng Technology Building, Huahui Road, Dalang Street, Longhua District, Shenzhen, China 4.7 Test Facility • A2LA (Certificate No. 4742.01) Shenzhen Huaxia Testing Technology Co., Ltd., Shenzhen EMC Laboratory is accredited by the American Association for Laboratory Accreditation(A2LA). Certificate No. 4742.01. • FCC Registration No.: 522263 Shenzhen Huaxia Testing Technology Co., Ltd., Shenzhen EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications Commission. The acceptance letter from the FCC is maintained in our files. Registration No.:522263 4.8 Deviation from Standards None. 4.9 Other Information Requested by the Customer None. Page:7 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 4.10 Equipment List Instrument Calibration Calibration Test Equipment Manufacturer Model No. No. Date Due Date EMI Test Receiver R&S ESR7 CQA-005 2018/9/26 2019/9/25 AFS4-00010300-18-10P- 2018/9/26 2019/9/25 Preamplifier MITEQ 4 CQA-035 Loop antenna Schwarzbeck FMZB1516 CQA-087 2018/10/28 2020/10/27 Bilog Antenna R&S HL562 CQA-011 2018/9/26 2020/9/25 Coaxial Cable (Above 1GHz) CQA N/A C019 2018/9/26 2019/9/25 Coaxial Cable (Below 1GHz) CQA N/A C020 2018/9/26 2019/9/25 EMI Test Receiver R&S ESPI3 CQA-013 2018/9/26 2019/9/25 LISN R&S ENV216 CQA-003 2018/11/5 2019/11/4 Coaxial cable CQA N/A CQA-C009 2018/9/26 2019/9/25 Page:8 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 5 Test results and Measurement Data 5.1 Antenna Requirement Standard requirement: 47 CFR Part 15C Section 15.203 15.203 requirement: An intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator, the manufacturer may design the unit so that a broken antenna can be replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. 15.247(b) (4) requirement: The conducted output power limit specified in paragraph (b) of this section is based on the use of antennas with directional gains that do not exceed 6 dBi. Except as shown in paragraph (c) of this section, if transmitting antennas of directional gain greater than 6 dBi are used, the conducted output power from the intentional radiator shall be reduced below the stated values in paragraphs (b)(1), (b)(2), and (b)(3) of this section, as appropriate, by the amount in dB that the directional gain of the antenna exceeds 6 dBi. EUT Antenna: The antenna is Induction coil. The best case gain of the antenna is 0dBi. Page:9 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 5.2 Conducted Emissions Test Requirement: 47 CFR Part 15C Section 15.207 Test Method: ANSI C63.10: 2013 Test Frequency Range: 150kHz to 30MHz Limit: Limit (dBuV) Frequency range (MHz) Quasi-peak Average 0.15-0.5 66 to 56* 56 to 46* 0.5-5 56 46 5-30 60 50 * Decreases with the logarithm of the frequency. Test Procedure: 1) The mains terminal disturbance voltage test was conducted in a shielded room. 2) The EUT was connected to AC power source through a LISN 1 (Line Impedance Stabilization Network) which provides a 50Ω/50µH + 5Ω linear impedance. The power cables of all other units of the EUT were connected to a second LISN 2, which was bonded to the ground reference plane in the same way as the LISN 1 for the unit being measured. A multiple socket outlet strip was used to connect multiple power cables to a single LISN provided the rating of the LISN was not exceeded. 3) The tabletop EUT was placed upon a non-metallic table 0.8m above the ground reference plane. And for floor-standing arrangement, the EUT was placed on the horizontal ground reference plane. 4) The test was performed with a vertical ground reference plane. The rear of the EUT shall be 0.4 m from the vertical ground reference plane. The vertical ground reference plane was bonded to the horizontal ground reference plane. The LISN 1 was placed 0.8 m from the boundary of the unit under test and bonded to a ground reference plane for LISNs mounted on top of the ground reference plane. This distance was between the closest points of the LISN 1 and the EUT. All other units of the EUT and associated equipment was at least 0.8 m from the LISN 2. 5) In order to find the maximum emission, the relative positions of equipment and all of the interface cables must be changed according to ANSI C63.10: 2013 on conducted measurement. Test Setup: Test Results: Pass Page:10 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 Measurement Data the worst case Mode a: Live line: Remark: 1. The following Quasi-Peak and Average measurements were performed on the EUT: 2. Final Test Level =Receiver Reading + LISN Factor + Cable Loss. 3. If the Peak value under Average limit, the Average value is not recorded in the report. Page:11 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 the worst case Mode a: Neutral line: Remark: 1. The following Quasi-Peak and Average measurements were performed on the EUT: 2. Final Test Level =Receiver Reading + LISN Factor + Cable Loss. 3. If the Peak value under Average limit, the Average value is not recorded in the report. Page:12 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 5.3 20dB Occupy Bandwidth Test Requirement: 47 CFR Part 15C Section 15.215 Test Method: ANSI C63.10 2013 Test Setup: Remark: Offset=Cable loss+ attenuation factor. Test Results: Pass Measurement Data Mode a Test Frequency (KHz) 20dB Occupy Bandwidth (kHz) Result 146.6 0.039 Pass Page:13 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 Test plot as follows: Graphs 110K Date: 29.MAR.2019 09:09:30 Page:14 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 5.4 Radiated Spurious Emission & Restricted bands 5.4.1 Spurious Emissions Test Requirement: 47 CFR Part 15C Section 15.209 and 15.205 Test Method: ANSI C63.10 2013 Test Site: Measurement Distance: 3m (Semi-Anechoic Chamber) Receiver Setup: Frequency Detector RBW VBW Remark 0.009MHz-0.090MHz Peak 10kHz 30kHz Peak 0.009MHz-0.090MHz Average 10kHz 30kHz Average 0.090MHz-0.110MHz Quasi-peak 10kHz 30kHz Quasi-peak 0.110MHz-0.490MHz Peak 10kHz 30kHz Peak 0.110MHz-0.490MHz Average 10kHz 30kHz Average 0.490MHz -30MHz Quasi-peak 10kHz 30kHz Quasi-peak 30MHz-1GHz Quasi-peak 100 kHz 300kHz Quasi-peak Peak 1MHz 3MHz Peak Above 1GHz Peak 1MHz 10Hz Average Limit: Field strength Limit Measurement Frequency Remark (microvolt/meter) (dBuV/m) distance (m) 0.009MHz-0.490MHz 2400/F(kHz) - - 300 0.490MHz-1.705MHz 24000/F(kHz) - - 30 1.705MHz-30MHz 30 - - 30 30MHz-88MHz 100 40.0 Quasi-peak 3 88MHz-216MHz 150 43.5 Quasi-peak 3 216MHz-960MHz 200 46.0 Quasi-peak 3 960MHz-1GHz 500 54.0 Quasi-peak 3 Above 1GHz 500 54.0 Average 3 Note: 15.35(b), Unless otherwise specified, the limit on peak radio frequency emissions is 20dB above the maximum permitted average emission limit applicable to the equipment under test. This peak limit applies to the total peak emission level radiated by the device. Page:15 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 Test Setup: Figure 1. Below 30MHz 150cm Figure 2. 30MHz to 1GHz Figure 3. Above 1 GHz Test Procedure: a. 1) Below 1G: The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter semi-anechoic camber. The table was rotated 360 degrees to determine the position of the highest radiation. 2) Above 1G: The EUT was placed on the top of a rotating table 1.5 meters above the ground at a 3 meter semi-anechoic camber. The table was rotated 360 degrees to determine the position of the highest radiation. Note: For the radiated emission test above 1GHz: Place the measurement antenna away from each area of the EUT determined to be a source of emissions at the specified measurement distance, while keeping the measurement antenna aimed at the source of emissions at each frequency of significant emissions, with polarization oriented for maximum response. The measurement antenna may have to be higher or lower than the EUT, depending on the radiation pattern of the emission and staying aimed at the emission source for receiving the maximum signal. The final measurement antenna elevation shall be that which maximizes the emissions. The measurement antenna elevation for maximum emissions shall be restricted to a range of heights of from 1 m to 4 m above the ground or reference ground plane. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the Page:16 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters (for the test frequency of below 30MHz, the antenna was tuned to heights 1 meter) and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. g. Repeat above procedures until all frequencies measured was complete. Test Results: Pass Radiated Emission below 9K~30MHz the worst case Test mode: Mode a Factor Level Limit Frequency Reading Margin Polarization dB dB(uV/m) dB(uV/m) Pass/Fail MHz dB(uV) dB (1/m) Peak Average 0.1466 Face 47.53 19.54 67.07 104.28 37.21 Pass 0.1466 Side 46.71 19.54 66.25 104.28 38.03 Pass Note: No other emissions found between lowest internal used/generated frequencies to 30MHz. The peak level of the emission is less than the average limit, so the average level shall be less than the limit without test. Page:17 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 Radiated Emission 30MHz~1GHz, the worst case Test mode: Mode a Vertical Remark: The field strength is calculated by adding the Antenna Factor, Cable Factor & Preamplifier. The basic equation with a sample calculation is as follows: Final Test Level =Receiver Reading + Antenna Factor + Cable Factor Page:18 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 30MHz~1GHz, the worst case Test mode: Mode a Horizontal Remark: The field strength is calculated by adding the Antenna Factor, Cable Factor & Preamplifier. The basic equation with a sample calculation is as follows: Final Test Level =Receiver Reading + Antenna Factor + Cable Factor Page:19 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 6 Photographs - EUT Test Setup 6.1 Radiated Emission 9KHz~30MHz: 30MHz~1GHz: Page:20 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 6.2 Conducted Emission Page:21 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 7 Photographs - EUT Constructional Details Test Model No.: QITWST360GY-T Page:22 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 Page:23 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 Page:24 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 Page:25 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 Page:26 of 27

Shenzhen Huaxia Testing Technology Co., Ltd Report No.: CQASZ20190300180E-01 .The End Page:27 of 27


Document Created: 2019-04-16 21:57:22
Document Modified: 2019-04-16 21:57:22
© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC