MKBN02 Modular Approval Request Rev 2.1

FCC ID: 2AO94-MKBN02

Cover Letter(s)

Download: PDF
FCCID_4084707

Modular Transmitter Approval Request
Federal Communications Commission
Equipment Authorization Division
7435 Oakland Mills Road
Columbia, MD 21046
USA

Company name: MOKO TECHNOLOGY LTD.
FCC ID: 2AO94-MKBN02

Dear Sir/Madam,

In accordance with 47CFR 15.212 Modular Transmitters and KDB 996369 D01 „Module Equip
Auth Guide v02‟. FCC ID 2AO94-MKBN02
 has been examined against the following requirements.
  Requirement per 15.212 and KDB 996369 D01                              Explanation from Grantee
                                                                         (do not write yes/no, but explain why product
                                                                         complies/how it is achieved)
 The radio elements must have the radio frequency circuitry              No, The module equip with not own RF
 shielded. Physical components and tuning capacitor(s) may be            shielding.
 located external to the shield, but must be on the module
 assembly.
 The module must have buffered modulation/data inputs to ensure          The modular has buffered data inputs, it is
 that the device will comply with Part 15 requirements with any type     integrated in Modular MKBN02. Please see
 of input signal.                                                        schematic.pdf
                                                                         All power lines derived from the host device
                                                                         are regulated before energizing other circuits
 The module must contain power supply regulation on the module.
                                                                         internal to the MKBN02 Please see
                                                                         schematic.pdf
 The module must contain a permanently attached antenna, or              The MKBN02 meets the FCC antenna
 contain a unique antenna connector, and be marketed and                 requirements. It has an integrated
 operated only with specific antenna(s), per §§ 15.203, 15.204(b),       antenna,which permanently affixed.
 15.204(c), 15.212(a), 2.929(b).
                                                                         The MKBN02 was tested in a stand‐alone
 The module must demonstrate compliance in a stand-alone                 Please see setup photo.pdf
 configuration.

                                                                         The label position of MKBN02 is clearly
                                                                         indicated. Please see the label.pdf Please
                                                                         notice that if the FCC identification number is
                                                                         not visible when the module is installed inside
                                                                         another device, then the outside of the device
 The module must be labeled with its permanently affixed FCC ID
                                                                         into which the module is installed must also
 label, or use an electronic display (see KDB Publication 784748).
                                                                         display a label referring to the enclosed
                                                                         module. This exterior label can use wording
                                                                         such as the following: “Contains Transmitter
                                                                         Module FCC ID: 2AO94-MKBN02” or
                                                                         “Contains FCC ID: 2AO94-MKBN02”
 The module must comply with all specific rules applicable to the        The MKBN02 is compliant with all applicable
 transmitter, including all the conditions provided in the integration   FCC rules. Detail instructions are given in the
 instructions by the grantee.                                            Users Manual
                                                                         The MKBN02 comply with applicable RF
 The module must comply with RF exposure requirements                    exposure requirements. Please see RF
                                                                         exposure statement. pdf




FCC Modular Approval Request Rev 2.1


Name: jinghui Chen                     Date: 2018/10/23

Title: CEO
Signature of applicant




FCC Modular Approval Request Rev 2.1



Document Created: 2018-10-25 15:58:56
Document Modified: 2018-10-25 15:58:56

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC