Test Report revised 0604

FCC ID: 2AO5N-ONXD18

Test Report

Download: PDF
FCCID_3874130

FCC and IC Test Report for Parts 15.247, 15.207 and 15.209 (DTS) and RSS-247, RSS Gen Product name : Onyx-PCB Applicant : Feel Robotics FCC ID : 2AO5N-ONXD18 IC ID : 23801-ONXD18 Test report No. : 180201427 002 v3.00

Report number: 180201427 002 v3.00 Laboratory information Accreditation Telefication is designated by the FCC as an Accredited Test Firm for compliance testing of equipment subject to Certification under Parts 15 & 18. The Designation number is: NL0001. The Industry Canada registration number for the 3 meter test chamber of Telefication is: 4173A-1. Documentation Telefication complies with the accreditation criteria for test laboratories as laid down in ISO/IEC 17025:2005. The accreditation covers the quality system of the laboratory as well as the specific activities as described in the authorized annex bearing the accreditation number L021 and is granted on 30 November 1990 by the Dutch Council For Accreditation (RvA: Raad voor Accreditatie). The test report must always be reproduced in full; reproduction of an excerpt only is subject to written approval of the testing laboratory. The documentation of the testing performed on the tested devices is archived for 10 years at Telefication Netherlands. Testing Location Test Site Telefication BV Test Site location Edisonstraat 12a 6902 PK Zevenaar The Netherlands Tel. +31889983600 Fax. +31316583189 Test Site FCC NL0001 Page 1 of 27

Report number: 180201427 002 v3.00 Revision History Version Date Remarks By v0.50 23-04-2018 First draft PvW v1.00 03-05-2018 Initial release PvW v2.00 24-05-2018 Updated emission designator on page 7 KR v3.00 04-06-2018 Updated channel 1 frequency type error on KR page 12, 13, 16 and 17 Page 2 of 27

Report number: 180201427 002 v3.00 Table of Contents Revision History .............................................................................................................................................. 2 Summary of Test results .................................................................................................................................. 5 1 General Description ................................................................................................................................. 6 1.1 Applicant................................................................................................................................................6 1.2 Manufacturer ........................................................................................................................................6 1.3 Tested Equipment Under Test (EUT) .....................................................................................................6 1.4 Product specifications of Equipment under test ...................................................................................7 1.5 Modification of the Equipment Under Test (EUT) .................................................................................7 1.6 Observations and remarks.....................................................................................................................7 1.7 Environmental conditions......................................................................................................................7 1.8 Measurement Standards .......................................................................................................................7 1.9 Applicable Standards .............................................................................................................................7 1.10 Conclusions ............................................................................................................................................8 2 Test configuration of the Equipment Under Test ..................................................................................... 9 2.1 Test mode ..............................................................................................................................................9 2.2 Tested channels and Data rates ............................................................................................................9 2.3 Test setups .............................................................................................................................................9 2.4 Equipment used in the test configuration ...........................................................................................10 2.5 Sample calculation ...............................................................................................................................11 3 Test results ............................................................................................................................................ 12 3.1 6dB bandwidth Measurement .............................................................................................................12 3.1.1 Limit.................................................................................................................................................12 3.1.2 Measurement instruments .............................................................................................................12 3.1.3 Test setup ........................................................................................................................................12 3.1.4 Test procedure ................................................................................................................................12 3.1.5 Test Results of the 6 dB bandwidth Measurement .........................................................................12 3.2 99% Occupied Bandwidth ....................................................................................................................13 3.2.1 Limit.................................................................................................................................................13 3.2.2 Measurement instruments .............................................................................................................13 3.2.3 Test setup ........................................................................................................................................13 3.2.4 Test procedure ................................................................................................................................13 3.2.5 Test results of the 99% occupied bandwidth measurement...........................................................13 3.2.6 Plots of the 99% occupied bandwidth measurement .....................................................................14 3.3 Output Power Measurement ..............................................................................................................16 3.3.1 Limit.................................................................................................................................................16 3.3.2 Measurement instruments .............................................................................................................16 3.3.3 Test setup ........................................................................................................................................16 Page 3 of 27

Report number: 180201427 002 v3.00 3.3.4 Test procedure ................................................................................................................................16 3.3.5 Test results of Output Power Measurement...................................................................................16 3.4 Power Spectral Density........................................................................................................................17 3.4.1 Limit.................................................................................................................................................17 3.4.2 Measurement instruments .............................................................................................................17 3.4.3 Test setup ........................................................................................................................................17 3.4.4 Test procedure ................................................................................................................................17 3.4.5 Test results of Power Spectral Density Measurement ....................................................................17 3.5 Band edge Measurement ....................................................................................................................18 3.5.1 Limit.................................................................................................................................................18 3.5.2 Measurement instruments .............................................................................................................18 3.5.3 Test setup ........................................................................................................................................18 3.5.4 Test procedure ................................................................................................................................18 3.5.5 Measurement Uncertainty ..............................................................................................................18 3.5.6 Plots of the Band edge Measurements ...........................................................................................18 3.6 Radiated Spurious Emissions Measurement .......................................................................................20 3.6.1 Limit.................................................................................................................................................20 3.6.2 Measurement instruments .............................................................................................................20 3.6.3 Test setup ........................................................................................................................................20 3.6.4 Test procedure ................................................................................................................................20 3.6.5 Notes ...............................................................................................................................................20 3.6.6 Plots of the Radiated Spurious Emissions .......................................................................................21 3.6.7 Measurement Uncertainty ..............................................................................................................25 3.7 AC conducted mains measurement ....................................................................................................26 3.7.1 Limit.................................................................................................................................................26 3.7.2 Measurement instruments .............................................................................................................26 3.7.3 Test setup ........................................................................................................................................26 3.7.4 Test procedure ................................................................................................................................26 3.7.5 Test results and plots of the AC conducted mains measurement ..................................................26 3.7.6 Measurement uncertainty ..............................................................................................................26 3.7.7 Plots of the AC conducted spurious measurement .........................................................................27 Page 4 of 27

Report number: 180201427 002 v3.00 Summary of Test results FCC ISED Description Section in Verdict report 15.247 (a) -- 6dB Bandwidth 3.1 Pass -- RSS-Gen 6.6 99% Bandwidth 3.2 Pass 15.247 (b) RSS-247 5.1 (2) RF output power 3.3 Pass 15.247 (e) RSS-247 5.2 (2) Power spectral density 3.4 Pass 15.247 (d) RSS-247 5.5 Band edge 3.5 Pass 15.209 (a) RSS-247 5.4 Radiated Spurious emissions 3.6 Pass 15.205 (a) RSS Gen 8.10 Spurious emissions in the restricted bands 3.6 Pass 15.207 (c) RSS-Gen 8.8 Conducted spurious emissions on AC mains 3.7 Pass Page 5 of 27

Report number: 180201427 002 v3.00 1 General Description 1.1 Applicant Client name: Feel Robotics B.V. Address Amstelplein 62, 30th Floor, Amsterdam, the Netherlands Zip code: 1096 BC Telephone: (0)20 737 1194 E-mail: maurice@kiiroo.com Contact name: Maurice op de Beek 1.2 Manufacturer Manufacturer name: Feel Robotics B.V. Address: Amstelplein 62, 30th Floor, Amsterdam, the Netherlands Zip code: 1096 BC Telephone: (0)20 737 1194 E-mail: maurice@kiiroo.com Contact name: Maurice op de Beek 1.3 Tested Equipment Under Test (EUT) Product name: Massager Brand name: Kiiroo Product type: Onyx 3 FCC ID: 2AO5N-ONXD18 IC ID 23801-ONXD18 Software version: -- Hardware version: B Date of receipt 26-02-2018 Tests started: 26-02-2018 Testing ended: 09-03-2018 Page 6 of 27

Report number: 180201427 002 v3.00 1.4 Product specifications of Equipment under test TX Frequency range (MHz) 2400 – 2483.5 RX frequency range (MHz) 2400 – 2483.5 Maximum output power to antenna (dBm) -0.16 Antenna type PCB antenna Antenna gain (dBi) 2.0 Type of modulation GFSK Emission designator BLE 1M01G1D 1.5 Modification of the Equipment Under Test (EUT) The manufacturer provided both a radiated sample and a conducted sample for radio testing. 1.6 Observations and remarks None. 1.7 Environmental conditions Test date 26-02-2018 27-02-2018 09-03-2018 Ambient temperature 20.9 °C 20.4 °C 21.4 °C Humidity 27.5 % 26.6 % 31.2 % 1.8 Measurement Standards • FCC KDB Publication No. 558074 D01DTS Meas. Guidance V04 • ANSI C63.10:2013 1.9 Applicable Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards: • FCC Part 15 Subpart C §15.247, §15.207, §15.209 • RSS-247 Issue 1, RSS-Gen Issue 4 Page 7 of 27

Report number: 180201427 002 v3.00 1.10 Conclusions The sample of the product showed NO NON-COMPLIANCES to the specifications stated in paragraph 1.9 of this report. The results of the test as stated in this report, are exclusively applicable to the product items as identified in this report. Telefication accepts no responsibility for any properties of product items in this test report, which are not supported by the tests as specified in paragraph 1.9 “Applicable standards”. All tests are performed by: Name : P. van Wanrooij, BASC Review of test methods and report by: Name : ing. R. van Barneveld The above conclusions have been verified by the following signatory: Date : 04-06-2018 Name : ing. K.A. Roes Function : Coordinator Radio Laboratory Signature : Page 8 of 27

Report number: 180201427 002 v3.00 2 Test configuration of the Equipment Under Test 2.1 Test mode The applicant provided test mode firmware for the EUT, in which it was possible to configure the EUT into different test channels. 2.2 Tested channels and Data rates Technology Channels Data rate Frequency (MHz) 1 (Low) 1 Mbps 2402 Bluetooth Low Energy 18 (Mid) 1 Mbps 2440 39 (High) 1 Mbps 2480 2.3 Test setups Radiated emissions test setup 30 MHz - 1 GHz Radiated emissions test setup above 1 GHz Page 9 of 27

Report number: 180201427 002 v3.00 Emissions test AC mains 2.4 Equipment used in the test configuration Description Manufacturer Model ID Used at Par. Spectrum Analyzer Rohde & Schwarz FSV40 TE01269 3.1, 3.4 Spectrum Analyzer Rohde & Schwarz FSP40 TE11125 3.5 Spectrum Analyzer Rohde & Schwarz ESR7 TE01220 3.5 -3.6 Biconilog Antenna Chase CBL6112A TE00967 3.5 Horn Antenna EMCO The Electro – 3115 TE00531 3.5 Mechanics Co Horn Antenna Flann Microwave 20240-25 TE00818 3.5 SAC Chamber Comtest Engineering - TE00861 3.5 BV Band reject filter 5N45-2441/T83-0/0 WHK3.0/18G-10EF TE00932 3.5 Pre-amplifier Miteq Js4-18004000-30-8P-A1 TE11131 3.5 Pre-amplifier Miteq AFS42-041001800-29-OP-42 TE00092 3.6 Software DARE Instruments Radimation 2016.2.8 -- 3.5 Software DARE Instruments Radimation 2017.2.5 -- 3.6 Artificial Mains Rohde & Schwarz ESH3-Z5 TE00208 3.6 Network (AMN) Pulse Limiter Rohde & Schwarz ESH3-Z2 TE00756 3.6 Page 10 of 27

Report number: 180201427 002 v3.00 2.5 Sample calculation Field Strength Measurement example: Frequency (GHz) Polarization Height(m) Peak (dBµV/m) 7,236 Horizontal 2 52.5 The following relation applies: E (dBµV/m) = U(dBµV) + AF (dB/m) – G (dB) + CL (dB) Where: E = Electric field strength U = Measuring receiver voltage AF = Antenna factor G = Gain of the pre-amplifier CL = Cable loss (52.5 = 48.12 + 36.1 - 37.42 + 5.7) Page 11 of 27

Report number: 180201427 002 v3.00 3 Test results 3.1 6dB bandwidth Measurement 3.1.1 Limit The minimum 6 dB Bandwidth shall be at least 500 kHz. 3.1.2 Measurement instruments The measurement instruments are listed in chapter 2.4 of this report. 3.1.3 Test setup The test setup is as shown in chapter 2.3 of this report. 3.1.4 Test procedure The testing follows FCC KDB Publication No. 558074 D01 DTS Meas. Guidance v04. IRN 017 - Occupied bandwidth (Hz) Method 4 – DTS Bandwidth. 3.1.5 Test Results of the 6 dB bandwidth Measurement Frequency 6dB bandwidth Technology Std. Channel Data rate (MHz) (kHz) 1 2402 1 Mbps 651.6 Bluetooth Low energy 18 2440 1 Mbps 652.0 39 2480 1 Mbps 651.0 Uncertainty ± 36.2 kHz Page 12 of 27

Report number: 180201427 002 v3.00 3.2 99% Occupied Bandwidth 3.2.1 Limit According to RSS-Gen 6.6 3.2.2 Measurement instruments The measurement instruments are listed in chapter 2.4 of this report. 3.2.3 Test setup The test setup is as shown in chapter 2.3 of this report. 3.2.4 Test procedure IRN 017 - Occupied bandwidth (Hz) Method 1 – XX % power bandwidth. 1. Set the centre frequency to the nominal EUT channel centre frequency 2. Set span = 1.5 times to 0.5 times the Occupied Bandwidth 3. Set VBW ≥ 3x RBW 4. Video averaging is not permitted. Where practical, detection and single sweep mode shall be used. Otherwise, peak detection and max hold mode (until the trace stabilizes) shall be used. 3.2.5 Test results of the 99% occupied bandwidth measurement Frequency 99% bandwidth Technology Std. Channel Data rate (MHz) (kHz) 1 2402 1 Mbps 1008 Bluetooth Low energy 18 2440 1 Mbps 1012 39 2480 1 Mbps 1008 Uncertainty ± 12 kHz Page 13 of 27

Report number: 180201427 002 v3.00 3.2.6 Plots of the 99% occupied bandwidth measurement Channel 1 Page 14 of 27

Report number: 180201427 002 v3.00 Channel 18 Channel 39 Page 15 of 27

Report number: 180201427 002 v3.00 3.3 Output Power Measurement 3.3.1 Limit For systems using digital modulation in the 2400-2483.5 MHz, the limit for the peak output power is 30 dBm. If transmitting antenna of directional gain greater than 6 dBi is used, the peak output power from the intentional radiator shall be reduced below the above stated value by the amount in dB that the directional gain of the antenna exceeds 6 dBi. In case of point to point operation, the limit has to be reduced by 1 dB for every 3 dB that the directional gain of the antenna exceeds 6 dBi. 3.3.2 Measurement instruments The measurement instruments are listed in chapter 2.4 of this report. 3.3.3 Test setup The test setup is as shown in chapter 2.3 of this report. 3.3.4 Test procedure The testing follows FCC KDB Publication No. 558074 D01 DTS Meas. Guidance v04. IRN 014 - RF power (W) - Method 1 – AVGSA (DTS) according to ANSI C63.10. 3.3.5 Test results of Output Power Measurement Peak method Frequency Peak output power Technology Std. Channel Data rate (MHz) (dBm) 1 2402 1 Mbps -1.47 Bluetooth Low Energy 18 2440 1 Mbps -0.53 39 2480 1 Mbps -0.16 Uncertainty ±0.71 dB Page 16 of 27

Report number: 180201427 002 v3.00 3.4 Power Spectral Density 3.4.1 Limit The peak power spectral density shall not be greater than 8 dBm in any 3 kHz band at any time interval of continuous transmission. 3.4.2 Measurement instruments The measurement instruments are listed in chapter 2.4 of this report. 3.4.3 Test setup The test setup is as shown in chapter 2.3 of this report. 3.4.4 Test procedure The testing follows FCC KDB Publication No. 558074 D01 DTS Meas. Guidance v04. IRN 030 - Spectral power density (W per n.Hz) - Method 5 – Peak method PKPSD (PSD in 3 kHz band) 3.4.5 Test results of Power Spectral Density Measurement Peak Power spectral density Frequency PSD/3 kHz Technology Std. Channel Data rate (MHz) (dBm) 1 2402 1 Mbps -17.69 Bluetooth Low 18 2440 1 Mbps -16.61 Energy 39 2480 1 Mbps -16.61 Uncertainty ±2 dB Page 17 of 27

Report number: 180201427 002 v3.00 3.5 Band edge Measurement 3.5.1 Limit Band edge: At the edge of the authorized band the RF power shall be at least 20 dB down. 3.5.2 Measurement instruments The measurement instruments are listed in chapter 2.4 of this report. 3.5.3 Test setup The test setup is as shown in chapter 2.3 of this report. 3.5.4 Test procedure According to KDB Publication 558074 V04, sections 11.3 and 12.1. IRN 026 - Radiated electrical disturbance (V per m) Method 6 – Radiated electrical disturbance at the Authorized band edge. 3.5.5 Measurement Uncertainty ± 5.7 dB. 3.5.6 Plots of the Band edge Measurements See next page Page 18 of 27

Report number: 180201427 002 v3.00 BLE Lower band edge (Channel 1) BLE Upper band edge (Channel 39) Page 19 of 27

Report number: 180201427 002 v3.00 3.6 Radiated Spurious Emissions Measurement 3.6.1 Limit The emissions from an intentional radiator shall not exceed the field strength levels specified in the following table: 15.209 Frequency (MHz) Field strength (µV/m) Measurement distance(m) 0.009 – 0.490 2400/F(kHz) 300 0.490 – 1.705 24000/F(kHz) 30 1.705 - 30 30 30 30 -88 100 3 88 - 216 150 3 216-960 200 3 Above 960 500 3 3.6.2 Measurement instruments The measurement instruments are listed in chapter 2.4 of this report. 3.6.3 Test setup The test setup is as shown in chapter 2.3 of this report. 3.6.4 Test procedure The emission limits shown in the above table are based on measurements employing a CISPR quasi-peak detector except for the frequency bands 9–90 kHz, 110–490 kHz and above 1000 MHz. Radiated emission limits in these three bands are based on measurements employing an average detector. Other details are according to KDB Publication 558074 V04, sections 11.3 and 12.1. IRN 026 - Radiated electrical disturbance (V per m) Method 1 – 30 MHz – 1 GHz in SAR. IRN 026 - Radiated electrical disturbance (V per m) Method 2 – 1 - 18 GHz in SAR. IRN 026 - Radiated electrical disturbance (V per m) Method 3 – 18 - 26.5 GHz in SAR. 3.6.5 Notes • In the frequency range of 1 – 26 GHz the green trace is measured using a peak detector and the red trace is measured using an average detector. The top limit line represent the peak limit and the bottom limit represents the average limit • The peak exceeding the spurious limits at 2.4 GHz in the 1-18 GHz plots is the transmission frequency, and therefore not subject to the limit. Page 20 of 27

Report number: 180201427 002 v3.00 3.6.6 Plots of the Radiated Spurious Emissions 30 MHz to 1 GHz Vertical polarization 15.209/15.247 RBW: 120 kHz, Vertical Max Peak 65 60 55 50 45 Electrical Field (dBµV/m) 40 Low ch 35 30 25 20 15 10 5 30 M 50 M 100 M 200 M 300 M 500 M 1G Frequency (Hz) 15.209/15.247 RBW: 120 kHz, Vertical Max Peak 65 60 55 50 45 Electrical Field (dBµV/m) 40 35 Mid ch 30 25 20 15 10 5 30 M 50 M 100 M 200 M 300 M 500 M 1G Frequency (Hz) 15.209/15.247 RBW: 120 kHz, Vertical Max Peak 65 60 55 50 45 Electrical Field (dBµV/m) 40 35 High ch 30 25 20 15 10 5 30 M 50 M 100 M 200 M 300 M 500 M 1G Frequency (Hz) Page 21 of 27

Report number: 180201427 002 v3.00 30 MHz to 1 GHz Horizontal polarization 15.209/15.247 RBW: 120 kHz, Horizontal Max Peak 65 60 55 50 45 Electrical Field (dBµV/m) 40 Low ch 35 30 25 20 15 10 5 30 M 50 M 100 M 200 M 300 M 500 M 1G Frequency (Hz) 15.209/15.247 RBW: 120 kHz, Horizontal Max Peak 60 50 40 Electrical Field (dBµV/m) Mid ch 30 20 10 0 30 M 50 M 100 M 200 M 300 M 500 M 1G Frequency (Hz) 15.209/15.247 RBW: 120 kHz, Horizontal Max Peak 60 50 40 Electrical Field (dBµV/m) High ch 30 20 10 0 30 M 50 M 100 M 200 M 300 M 500 M 1G Frequency (Hz) Page 22 of 27

Report number: 180201427 002 v3.00 1 GHz to 18 GHz Vertical polarization Limit Average 1 - 18 GHz Limit Peak 1 - 18 GHz RBW: 1 MHz, Vertical Max Average RBW: 1 MHz, Vertical Max Peak 90 80 70 Electrical Field (dBµV/m) 60 Low ch 50 40 30 20 10 1G 2G 3G 5G 10 G 18 G Frequency (Hz) Limit Average 1 - 18 GHz Limit Peak 1 - 18 GHz RBW: 1 MHz, Vertical Max Average RBW: 1 MHz, Vertical Max Peak 100 90 80 70 Electrical Field (dBµV/m) 60 Mid ch 50 40 30 20 10 1G 2G 3G 5G 10 G 18 G Frequency (Hz) Limit Average 1 - 18 GHz Limit Peak 1 - 18 GHz RBW: 1 MHz, Vertical Max Average RBW: 1 MHz, Vertical Max Peak 90 80 70 Electrical Field (dBµV/m) 60 High ch 50 40 30 20 10 1G 2G 3G 5G 10 G 18 G Frequency (Hz) Page 23 of 27

Report number: 180201427 002 v3.00 1 GHz to 18 GHz Horizontal polarization Limit Average 1 - 18 GHz Limit Peak 1 - 18 GHz RBW: 1 MHz, Horizontal Max Average RBW: 1 MHz, Horizontal Max Peak 100 90 80 70 Electrical Field (dBµV/m) 60 Low ch 50 40 30 20 10 1G 2G 3G 5G 10 G 18 G Frequency (Hz) Limit Average 1 - 18 GHz Limit Peak 1 - 18 GHz RBW: 1 MHz, Horizontal Max Average RBW: 1 MHz, Horizontal Max Peak 100 90 80 70 Electrical Field (dBµV/m) 60 Mid ch 50 40 30 20 10 1G 2G 3G 5G 10 G 18 G Frequency (Hz) Limit Average 1 - 18 GHz Limit Peak 1 - 18 GHz RBW: 1 MHz, Horizontal Max Average RBW: 1 MHz, Horizontal Max Peak 100 90 80 70 Electrical Field (dBµV/m) 60 High ch 50 40 30 20 10 1G 2G 3G 5G 10 G 18 G Frequency (Hz) Page 24 of 27

Report number: 180201427 002 v3.00 18 GHz to 26 GHz Limit Average 18 - 26 GHz Limit Peak 18 - 26 GHz RBW: 100 kHz, Vertical Max Average RBW: 100 kHz, Vertical Max Peak 85 80 75 70 65 Electrical Field (dBµV/m) Vertical 60 polarization 55 50 Mid ch 45 40 35 30 25 18 G 19 G 20 G 21 G 22 G 23 G 24 G 25 G 26 G Frequency (Hz) Limit Average 18 - 26 GHz Limit Peak 18 - 26 GHz RBW: 100 kHz, Horizontal Max Average RBW: 100 kHz, Horizontal Max Peak 85 80 75 70 65 Electrical Field (dBµV/m) Horizontal 60 polarization 55 50 Mid ch 45 40 35 30 25 18 G 19 G 20 G 21 G 22 G 23 G 24 G 25 G 26 G Frequency (Hz) 3.6.7 Measurement Uncertainty Measurement uncertainty Radiated emissions below 1 GHz Horizontal polarization 30 – 200 MHz 4.5 dB 200 – 1000 MHz 3.6 dB Vertical polarization 30 – 200 MHz 5.4 dB 200 – 1000 MHz 4.6 dB Measurement uncertainty Radiated emissions above 1 GHz 1000- 18000 MHZ 5.7 dB 18000 – 26000 MHZ 3.9 dB Page 25 of 27

Report number: 180201427 002 v3.00 3.7 AC conducted mains measurement 3.7.1 Limit According to 15.207 (c) An intentional radiator that is designed to be connected to the public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC power line on any frequency or frequencies, within the band 150 kHz to 30 MHz, shall not exceed the limits in the following table. 3.7.2 Measurement instruments The measurement instruments are listed in chapter 2.4 of this report. 3.7.3 Test setup The test setup is as shown in chapter 2.3 of this report. 3.7.4 Test procedure According to ANSI C63.4: 2014, section 13.3. IRN 029 - Conducted disturbance (V) Method 1 – AC mains conducted disturbance. 3.7.5 Test results and plots of the AC conducted mains measurement The EUT normally receives power from another device that in turn connects to the public-utility ac power lines, therefore the measurements are made with a representative charger with the EUT in operation to ensure that the device continues to comply with the appropriate limits while providing the EUT with power. The test results can be found on the next page. 3.7.6 Measurement uncertainty +/- 3.6 dB. Page 26 of 27

Report number: 180201427 002 v3.00 3.7.7 Plots of the AC conducted spurious measurement Phase 15.207 15.207 avg RBW: 9 kHz, Line 1 Max Average RBW: 9 kHz, Line 1 Max Peak 80 70 60 50 Voltage (dBµV) 40 30 20 10 0 150 k 300 k 500 k 600 k 1M 2M 3M 5M 10 M 20 M 30 M Frequency (Hz) Neutral 15.207 15.207 avg RBW: 9 kHz, Neutral Max Average RBW: 9 kHz, Neutral Max Peak 80 70 60 50 Voltage (dBµV) 40 30 20 10 0 150 k 300 k 500 k 600 k 1M 2M 3M 5M 10 M 20 M 30 M Frequency (Hz) Page 27 of 27


Document Created: 2019-09-23 09:23:56
Document Modified: 2019-09-23 09:23:56
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC