Test Report

FCC ID: 2ANKDJCHR35H5

Test Report

Download: PDF
FCCID_4046338

MRT Technology (Suzhou) Co., Ltd Report No.: 1809WU006-U1 Phone: +86-512-66308358 Report Version: V01 Web: www.mrt-cert.com Issue Date: 09-12-2018 MEASUREMENT REPORT FCC PART 15.249 FCC ID: 2ANKDJCHR35H5 APPLICANT: ZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY CO., LTD Application Type: Certification Product: RF Remote control Model No.: JCHR35H5-1, JCHR35H5-2, JCHR35H5-3, JCHR35H5-4 FCC Classification: Low Power Communication Device Transmitter (DXX) FCC Rule Part(s): Part 15.249 Test Procedure(s): ANSI C63.10 - 2013 Test Date: September 6 ~ 11, 2018 Reviewed By : ( Kevin Guo ) Approved By : ( Robin Wu ) The test results relate only to the samples tested. This equipment has been shown to be capable of compliance with the applicable technical standards as indicated in the measurement report and was tested in accordance with the measurement procedures specified in ANSI C63.10-2013. Test results reported herein relate only to the item(s) tested. The test report shall not be reproduced except in full without the written approval of MRT Technology (Suzhou) Co., Ltd. FCC ID: 2ANKDJCHR35H5 Page Number: 1 of 34

Report No.: 1809WSU006-U1 Revision History Report No. Version Description Issue Date Note 1809WSU006-U1 Rev. 01 Initial report 09-12-2018 Valid FCC ID: 2ANKDJCHR35H5 Page Number: 2 of 34

Report No.: 1809WSU006-U1 CONTENTS Description Page 1. INTRODUCTION ..................................................................................................................... 6 1.1. Scope ........................................................................................................................... 6 1.2. MRT Test Location ....................................................................................................... 6 2. PRODUCT INFORMATION ..................................................................................................... 7 2.1. Equipment Description.................................................................................................. 7 2.2. Operation Frequency and Channel List......................................................................... 7 2.3. Test Configuration ........................................................................................................ 7 2.4. Test Software ............................................................................................................... 7 2.5. EMI Suppression Device(s)/Modifications ..................................................................... 7 2.6. Labeling Requirements ................................................................................................. 7 3. DESCRIPTION OF TEST ........................................................................................................ 8 3.1. Evaluation Procedure ................................................................................................... 8 3.2. AC Line Conducted Emissions ..................................................................................... 8 3.3. Radiated Emissions ...................................................................................................... 9 4. ANTENNA REQUIREMENTS ................................................................................................ 10 5. TEST EQUIPMENT CALIBRATION DATE .............................................................................11 6. MEASUREMENT UNCERTAINTY ......................................................................................... 12 7. TEST RESULT ...................................................................................................................... 13 7.1. Summary .................................................................................................................... 13 7.2. Conducted Emission ................................................................................................... 14 7.2.1. Test Limit ................................................................................................................ 14 7.2.2. Test Setup............................................................................................................... 14 7.2.3. Test Result .............................................................................................................. 14 7.3. Radiated Emission ...................................................................................................... 15 7.3.1. Test Limit ................................................................................................................ 15 7.3.2. Test Setup............................................................................................................... 16 7.3.3. Test Result .............................................................................................................. 17 7.4. Radiated Restricted Band Edge Measurement ........................................................... 22 7.4.1. Test Limit ................................................................................................................ 22 7.4.2. Test Setup............................................................................................................... 23 7.4.3. Test Result .............................................................................................................. 24 7.5. 20dB Spectrum Bandwidth Measurement ................................................................... 28 7.5.1. Test Limit ................................................................................................................ 28 FCC ID: 2ANKDJCHR35H5 Page Number: 3 of 34

Report No.: 1809WSU006-U1 7.5.2. Test Procedure used ............................................................................................... 28 7.5.3. Test Setting ............................................................................................................. 28 7.5.4. Test Setup............................................................................................................... 28 7.5.5. Test Result .............................................................................................................. 29 7.6. 99% Bandwidth Measurement .................................................................................... 30 7.6.1. Test Limit ................................................................................................................ 30 7.6.2. Test Procedure used ............................................................................................... 30 7.6.3. Test Setting ............................................................................................................. 30 7.6.4. Test Setup............................................................................................................... 30 7.6.5. Test Result .............................................................................................................. 31 8. CONCLUSION....................................................................................................................... 32 Appendix A – Test Setup Photograph......................................................................................... 33 Appendix B – EUT Photograph ................................................................................................... 34 FCC ID: 2ANKDJCHR35H5 Page Number: 4 of 34

Report No.: 1809WSU006-U1 §2.1033 General Information Applicant: ZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY CO., LTD Applicant Address: No.19 XinTao Road, Provincial High Tech Park XinChangcounty,ZheJiang Province Manufacturer: ZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY CO., LTD Manufacturer Address: No.19 XinTao Road, Provincial High Tech Park XinChangcounty,ZheJiang Province Test Site: MRT Technology (Suzhou) Co., Ltd Test Site Address: D8 Building, Youxin Industrial Park, No.2 Tian’edang Rd., Wuzhong Economic Development Zone, Suzhou, China FCC Registration No.: 893164 Test Device Serial No.: N/A Production Pre-Production Engineering Test Facility / Accreditations Measurements were performed at MRT Laboratory located in Tian’edang Rd., Suzhou, China.  MRT facility is a FCC registered (MRT Reg. No. 893164) test facility with the site description report on file and has met all the requirements specified in ANSI C63.4-2014.  MRT facility is an IC registered (MRT Reg. No. 11384A-1) test laboratory with the site description on file at Industry Canada.  MRT facility is a VCCI registered (R-20025, G-20034, C-20020, T-20020) test laboratory with the site description on file at VCCI Council.  MRT Lab is accredited to ISO 17025 by the American Association for Laboratory Accreditation (A2LA) under the American Association for Laboratory Accreditation Program (A2LA Cert. No. 3628.01) in EMC, Telecommunications, Radio and SAR testing. FCC ID: 2ANKDJCHR35H5 Page Number: 5 of 34

Report No.: 1809WSU006-U1 1. INTRODUCTION 1.1. Scope Measurement and determination of electromagnetic emissions (EMC) of radio frequency devices including intentional and/or unintentional radiators for compliance with the technical rules and regulations of the Federal Communications Commission and the Industry Canada Certification and Engineering Bureau. 1.2. MRT Test Location The map below shows the location of the MRT LABORATORY, its proximity to the Taihu Lake. These measurement tests were conducted at the MRT Technology (Suzhou) Co., Ltd. Facility located at D8 Building, No.2 Tian’edang Rd., Wuzhong Economic Development Zone, Suzhou, China. The measurement facility compliant with the test site requirements specified in ANSI C63.4-2014. FCC ID: 2ANKDJCHR35H5 Page Number: 6 of 34

Report No.: 1809WSU006-U1 2. PRODUCT INFORMATION 2.1. Equipment Description Product Name RF Remote control Model No. JCHR35H5-1, JCHR35H5-2, JCHR35H5-3, JCHR35H5-4 Frequency Range 2404 ~ 2479 MHz Channel Number 5 Type of Modulation GFSK Note: Product supports transmitter only. 2.2. Operation Frequency and Channel List Channel Frequency Channel Frequency 01 2404 MHz 02 2419 MHz 03 2454 MHz 04 2469 MHz 05 2479 MHz --- --- 2.3. Test Configuration The EUT was tested as described in this report is in compliance with the requirements limits of FCC Rules Part 15.207, 15.209, 15.215 and 15.249. ANSI C63.10-2013 was used to reference the appropriate EUT setup for radiated spurious emissions testing and AC line conducted testing. 2.4. Test Software N/A 2.5. EMI Suppression Device(s)/Modifications No EMI suppression device(s) were added and/or no modifications were made during testing. 2.6. Labeling Requirements Per 2.1074 & 15.19; Docket 95-19 The label shall be permanently affixed at a conspicuous location on the device; instruction manual or pamphlet supplied to the user and be readily visible to the purchaser at the time of purchase. However, when the device is so small wherein placement of the label with specified statement is not practical, only the FCC ID must be displayed on the device per Section 15.19(a)(5). Please see attachment for FCC ID label and label location. FCC ID: 2ANKDJCHR35H5 Page Number: 7 of 34

Report No.: 1809WSU006-U1 3. DESCRIPTION OF TEST 3.1. Evaluation Procedure The measurement procedures described in the American National Standard for Testing Unlicensed Wireless Devices (ANSI C63.10-2013), and the requirements provided in FCC 15.207, 15.209, 15.215 and 15.249 were performed in the report of the EUT. Deviation from measurement procedure…………………………….....................................None 3.2. AC Line Conducted Emissions The line-conducted facility is located inside an 8'x4'x4' shielded enclosure. A 1m x 2m wooden table 80cm high is placed 40cm away from the vertical wall and 80cm away from the sidewall of the shielded room. Two 10kHz-30MHz, 50Ω/50uH Line-Impedance Stabilization Networks (LISNs) are bonded to the shielded room floor. Power to the LISNs is filtered by external high-current high-insertion loss power line filters. These filters attenuate ambient signal noise from entering the measurement lines. These filters are also bonded to the shielded enclosure. The EUT is powered from one LISN and the support equipment is powered from the second LISN. All interconnecting cables more than 1 meter were shortened to a 1 meter length by non-inductive bundling (serpentine fashion) and draped over the back edge of the test table. All cables were at least 40cm above the horizontal reference ground-plane. Power cables for support equipment were routed down to the second LISN while ensuring that that cables were not draped over the second LISN. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. The RF output of the LISN was connected to the receiver and exploratory measurements were made to determine the frequencies producing the maximum emission from the EUT. The receiver was scanned from 150kHz to 30MHz. The detector function was set to peak mode for exploratory measurements while the bandwidth of the analyzer was set to 9kHz. The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each emission. Each emission was also maximized by varying: power lines, the mode of operation or data exchange speed, or support equipment whichever determined the worst-case emission. Once the worst case emissions have been identified, the one EUT cable configuration/arrangement and mode of operation that produced these emissions are used for final measurements on the same test site. The analyzer is set to CISPR quasi-peak and average detectors with a 9kHz resolution bandwidth for final measurements. An extension cord was used to connect to a single LISN which powered by EUT. The extension cord was calibrated with LISN, the impedance and insertion loss are compliance with the requirements as stated in ANSI C63.10-2013. FCC ID: 2ANKDJCHR35H5 Page Number: 8 of 34

Report No.: 1809WSU006-U1 3.3. Radiated Emissions The radiated test facilities consisted of an indoor 3 meter semi-anechoic chamber used for final measurements and exploratory measurements, when necessary. The measurement area is contained within the semi-anechoic chamber which is shielded from any ambient interference. For measurements above 1GHz absorbers are arranged on the floor between the turn table and the antenna mast in such a way so as to maximize the reduction of reflections. For measurements below 1GHz, the absorbers are removed. A MF Model 210SS turntable is used for radiated measurement. It is a continuously rotatable, remote controlled, metallic turntable and 2 meters (6.56 ft.) in diameter. The turn table is flush with the raised floor of the chamber in order to maintain its function as a ground plane. An 80cm high PVC support structure is placed on top of the turntable. For all measurements, the spectrum was scanned through all EUT azimuths and from 1 to 4 meter receive antenna height using a broadband antenna from 30MHz up to the upper frequency shown in 15.33(b)(1) depending on the highest frequency generated or used in the device or on which the device operates or tunes. For frequencies above 1GHz, linearly polarized double ridge horn antennas were used. For frequencies below 30MHz, a calibrated loop antenna was used. When exploratory measurements were necessary, they were performed at 1 meter test distance inside the semi-anechoic chamber using broadband antennas, broadband amplifiers, and spectrum analyzers to determine the frequencies and modes producing the maximum emissions. Sufficient time for the EUT, support equipment, and test equipment was allowed in order for them to warm up to their normal operating condition. The test set-up for frequencies below 1GHz was placed on top of the 0.8 meter high, 1 x 1.5 meter table; and test set-up for frequencies 1-25GHz was placed on top of the 1.5 meter high, 1 x 1.5 meter table. The EUT, support equipment, and interconnecting cables were arranged and manipulated to maximize each emission. Appropriate precaution was taken to ensure that all emissions from the EUT were maximized and investigated. The system configuration, clock speed, mode of operation or video resolution, if applicable, turntable azimuth, and receive antenna height was noted for each frequency found. Final measurements were made in the semi-anechoic chamber using calibrated, linearly polarized broadband and horn antennas. The test setup was configured to the setup that produced the worst case emissions. The spectrum analyzer was set to investigate all frequencies required for testing to compare the highest radiated disturbances with respect to the specified limits. The turntable containing the EUT was rotated through 360 degrees and the height of the receive antenna was varied 1 to 4 meters and stopped at the azimuth and height producing the maximum emission. Each emission was maximized by changing the orientation of the EUT through three orthogonal planes and changing the polarity of the receive antenna, whichever produced the worst-case emissions. According to 3dB Beam-Width of horn antenna, the horn antenna should be always directed to the EUT when rising height. FCC ID: 2ANKDJCHR35H5 Page Number: 9 of 34

Report No.: 1809WSU006-U1 4. ANTENNA REQUIREMENTS Excerpt from §15.203 of the FCC Rules/Regulations: “An intentional radiator antenna shall be designed to ensure that no antenna other than that furnished by the responsible party can be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section.”  The antenna of the EUT is permanently attached.  There are no provisions for connection to an external antenna. Conclusion: This unit complies with the requirement of §15.203. FCC ID: 2ANKDJCHR35H5 Page Number: 10 of 34

Report No.: 1809WSU006-U1 5. TEST EQUIPMENT CALIBRATION DATE Conducted Emissions - SR2 Instrument Manufacturer Type No. Asset No. Cali. Interval Cali. Due Date EMI Test Receiver R&S ESR3 MRTSUE06185 1 year 2019/04/20 Two-Line V-Network R&S ENV 216 MRTSUE06002 1 year 2019/06/15 Two-Line V-Network R&S ENV 216 MRTSUE06003 1 year 2019/06/15 Thermohygrometer Testo 608-H1 MRTSUE06404 1 year 2019/08/15 Shielding Anechoic Chamber Mikebang Chamber-SR2 MRTSUE06214 N/A N/A Radiated Emission - AC1 Instrument Manufacturer Type No. Asset No. Cali. Interval Cal. Due Date PXA Signal Analyzer Keysight 9030B MRTSUE06395 1 year 2019/09/06 EMI Test Receiver R&S ESR7 MRTSUE06001 1 year 2019/08/14 Loop Antenna Schwarzbeck FMZB 1519 MRTSUE06025 1 year 2018/11/20 EXA Signal Analyzer Agilent N9020A MRTSUE06106 1 year 2019/04/20 Microwave System Amplifier Agilent 83017A MRTSUE06076 1 year 2018/11/17 Bilog Period Antenna Schwarzbeck VULB 9168 MRTSUE06172 1 year 2019/04/12 Broad Band Horn Antenna Schwarzbeck BBHA9120D MRTSUE06023 1 year 2018/10/21 Broad Band Horn Antenna Schwarzbeck BBHA 9170 MRTSUE06024 1 year 2018/12/14 Amplifier Schwarzbeck BBV 9721 MRTSUE06121 1 year 2019/06/13 Thermohygrometer Testo 608-H1 MRTSUE06403 1 year 2019/08/15 Anechoic Chamber TDK Chamber-AC1 MRTSUE06212 1 year 2019/05/08 Conducted Test Equipment - TR3 Instrument Manufacturer Type No. Asset No. Cali. Interval Cali. Due Date EXA Signal Analyzer Agilent N9020A MRTSUE06106 1 year 2019/04/20 Thermohygrometer Testo 608-H1 MRTSUE06401 1 year 2019/08/15 Software Version Function e3 V8.3.5 EMI Test Software FCC ID: 2ANKDJCHR35H5 Page Number: 11 of 34

Report No.: 1809WSU006-U1 6. MEASUREMENT UNCERTAINTY Where relevant, the following test uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR 16-4-2. This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k = 2. AC Conducted Emission Measurement - SR2 Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 150kHz~30MHz: 3.46dB Radiated Emission Measurement - AC1 Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 9kHz ~ 1GHz: 4.18dB 1GHz ~ 25GHz: 4.76dB 20dB Spectrum Bandwidth - TR3 Measuring Uncertainty for a Level of Confidence of 95% (U=2Uc(y)): 0.28% FCC ID: 2ANKDJCHR35H5 Page Number: 12 of 34

Report No.: 1809WSU006-U1 7. TEST RESULT 7.1. Summary Company Name: ZHEJIANG JIECANG LINEAR MOTION TECHNOLOGY CO., LTD Product: RF Remote control FCC Part Test Description Test Limit Test Test Reference Section(s) Condition Result AC Conducted Emissions Line Section 15.207 < FCC 15.207 limits N/A 150kHz - 30MHz Conducted 7.2 General Field Strength Emissions in restricted 15.209 Limits (Restricted Bands bands must meet the Section Radiated Pass 15.249 and Radiated Emission radiated limits detailed in 7.3 & 7.4 Limits) 15.209 & clause 8.10 20 dB bandwidth of the 20dB Spectrum Section 15.215(c) emission in the specific Conducted Pass Bandwidth 7.5 band Section 15.215(c) 99% Occupied Bandwidth N/A Conducted Pass 7.6 Notes: 1. All modes of operation and data rates were investigated. For radiated emission test, every axis (X, Y, Z) was also verified. The test results shown in the following sections represent the worst case emissions. 2. The analyzer plots shown in this section were all taken with a correction table loaded into the analyzer. The correction table was used to account for the losses of the cables and attenuators used as part of the system to connect the EUT to the analyzer at all frequencies of interest. FCC ID: 2ANKDJCHR35H5 Page Number: 13 of 34

Report No.: 1809WSU006-U1 7.2. Conducted Emission 7.2.1.Test Limit FCC 15.207 Limits Frequency (MHz) QP (dBuV) AV (dBuV) 0.15 ~ 0.50 66 ~ 56 56 ~ 46 0.50 ~ 5.0 56 46 5.0 ~ 30 60 50 Note 1: The lower limit shall apply at the transition frequencies. Note 2: The limit decreases linearly with the logarithm of the frequency in the range 0.15MHz to 0.5MHz. 7.2.2.Test Setup 7.2.3.Test Result The EUT is powered by battery, so this requirement does not apply. FCC ID: 2ANKDJCHR35H5 Page Number: 14 of 34

Report No.: 1809WSU006-U1 7.3. Radiated Emission 7.3.1.Test Limit FCC Part 15 Subpart C Paragraph 15.249 & RSS-210 Fundamental Frequency Field Strength of Fundamental Field Strength of Harmonics (MHz) (mV/m) (uV/m) 902 ~ 908 50 500 2400 ~ 2483.5 50 500 5725 ~ 5875 50 500 24000 ~ 24250 250 2500 FCC Part 15.249 (d), Emissions radiated outside of the specified frequency bands, except for harmonics, shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emission limits in §15.209, whichever is the lesser attenuation. FCC Part 15 Subpart C Paragraph 15.209 & RSS-Gen Frequency (MHz) Field Strength (uV/m) Measurement Distance (m) 0.009 ~ 0.490 2400/F(kHz) 300 0.490 ~ 1.705 24000/F(kHz) 30 1.705 ~ 30.0 30 30 30 ~ 80 100** 3 80 ~ 216 150** 3 216 ~ 960 200** 3 Above 960 500 3 Note 1: The lower limit shall apply at the transition frequency. Note 2: Distance refers to the distance in meters between the measuring instrument antenna and the closed point of any part of the device or system. Note 3: E field strength (dBuV/m) = 20 log E field strength (uV/m). FCC ID: 2ANKDJCHR35H5 Page Number: 15 of 34

Report No.: 1809WSU006-U1 7.3.2.Test Setup 9kHz ~ 30MHz Test Setup: 30MHz ~ 1GHz Test Setup: 1GHz ~ 25GHz Test Setup: FCC ID: 2ANKDJCHR35H5 Page Number: 16 of 34

Report No.: 1809WSU006-U1 7.3.3.Test Result Product RF Remote control Temperature 24°C Test Engineer Ternence Wang Relative Humidity 59% Test Site AC1 Test Date 2018/09/10 Time On One Period Duty Cycle Duty Cycle Factor (ms) (ms) (%) (dB) 13.5 100 13.50 -17.39 Note 1: Duty Cycle Factor = 20*Log (Duty Cycle) Note 2: Time On(ms)=0.3*45=13.5 ms Channel 2454MHz -- -- FCC ID: 2ANKDJCHR35H5 Page Number: 17 of 34

Report No.: 1809WSU006-U1 Product RF Remote control Temperature 25°C Test Engineer Ternence Wang Relative Humidity 52% Test Site AC1 Test Date 2018/09/07 Remark: Fundamental Radiated Emission Frequency Reading Factor Duty Cycle Measure Limit Margin Detector Polarization (MHz) Level (dB) Factor Level (dBμV/m) (dB) (dBμV) (dB) (dBμV/m) 58.4 32.3 N/A 90.7 114 -23.3 PK Horizontal 58.4 32.3 -17.4 73.3 94 -20.7 AV Horizontal 2404 43.6 32.3 N/A 75.9 114 -38.1 PK Vertical 43.6 32.3 -17.4 58.5 94 -35.5 AV Vertical 57.8 32.3 N/A 90.1 114 -23.9 PK Horizontal 57.8 32.3 -17.4 72.7 94 -21.3 AV Horizontal 2454 51.9 32.3 N/A 84.2 114 -29.8 PK Vertical 51.9 32.3 -17.4 66.8 94 -27.2 AV Vertical 58.0 32.3 N/A 90.4 114 -23.6 PK Horizontal 58.0 32.3 -17.4 73.0 94 -21.0 AV Horizontal 2479 51.6 32.3 N/A 84.0 114 -30.0 PK Vertical 51.6 32.3 -17.4 66.6 94 -27.4 AV Vertical Note 1: Peak Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Average Measure Level = Peak Measure Level + Duty Cycle Factor Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) Note 2: All readings below 1GHz are peak, above 1GHz are performed with peak and/or average measurements as necessary. FCC ID: 2ANKDJCHR35H5 Page Number: 18 of 34

Report No.: 1809WSU006-U1 Product RF Remote control Temperature 25°C Test Engineer Ternence Wang Relative Humidity 52% Test Site AC1 Test Date 2018/09/07 Remark: Harmonics Radiated Emission - 2404MHz Frequency Reading Factor Duty Cycle Measure Limit Margin Detector Polarization (MHz) Level (dB) Factor Level (dBμV/m) (dB) (dBμV) (dB) (dBμV/m) 118.2 2.2 13.0 N/A 15.3 43.5 -28.2 QP Horizontal 157.1 0.0 15.3 N/A 15.3 43.5 -28.2 QP Horizontal 44.5 0.3 14.3 N/A 14.6 40.0 -25.4 QP Vertical 122.2 5.2 13.4 N/A 18.6 43.5 -24.9 QP Vertical 4808.0 44.0 5.9 N/A 49.9 74.0 -24.1 PK Horizontal 7212.0 34.6 12.6 N/A 47.2 74.0 -26.8 PK Horizontal 9616.0 34.0 15.4 N/A 49.4 74.0 -24.6 PK Horizontal 12012.0 34.4 17.4 N/A 51.8 74.0 -22.2 PK Horizontal 4808.0 41.1 5.9 N/A 47.0 74.0 -27.0 PK Vertical 7212.0 34.8 12.6 N/A 47.4 74.0 -26.6 PK Vertical 9616.0 34.1 15.4 N/A 49.5 74.0 -24.5 PK Vertical 12012.0 33.2 17.4 N/A 50.6 74.0 -23.4 PK Vertical Note 1: Peak Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Average Measure Level = Peak Measure Level + Duty Cycle Factor Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) – Pre Amplifier Gain (dB) Note 2: Average measurement was not performed when the peak level lower than average limit. Note 3: The test trace is same as the ambient noise (the test frequency range: 9 kHz ~ 30 MHz and 18 GHz ~ 25 GHz), therefore no data appear in the report. FCC ID: 2ANKDJCHR35H5 Page Number: 19 of 34

Report No.: 1809WSU006-U1 Product RF Remote control Temperature 25°C Test Engineer Ternence Wang Relative Humidity 52% Test Site AC1 Test Date 2018/09/07 Remark: Harmonics Radiated Emission - 2454MHz Frequency Reading Factor Duty Cycle Measure Limit Margin Detector Polarization (MHz) Level (dB) Factor Level (dBμV/m) (dB) (dBμV) (dB) (dBμV/m) 117.5 3.0 13.0 N/A 16.0 43.5 -27.5 QP Horizontal 161.1 0.1 15.2 N/A 15.3 43.5 -28.2 QP Horizontal 123.0 6.2 13.4 N/A 19.7 43.5 -23.8 QP Vertical 729.4 2.6 22.5 N/A 25.1 46.0 -20.9 QP Vertical 4908.0 40.4 6.1 N/A 46.5 74.0 -27.5 PK Horizontal 7362.0 34.6 12.7 N/A 47.2 74.0 -26.8 PK Horizontal 9816.0 34.3 16.4 N/A 50.7 74.0 -23.3 PK Horizontal 12270.0 33.7 17.4 N/A 51.1 74.0 -22.9 PK Horizontal 4908.0 38.9 6.1 N/A 45.0 74.0 -29.0 PK Vertical 7362.0 34.9 12.7 N/A 47.6 74.0 -26.4 PK Vertical 9816.0 33.1 16.4 N/A 49.5 74.0 -24.5 PK Vertical 12270.0 33.4 17.4 N/A 50.8 74.0 -23.2 PK Vertical Note 1: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Average Measure Level = Peak Measure Level + Duty Cycle Factor Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) – Pre Amplifier Gain (dB) Note 2: Average measurement was not performed when the peak level lower than average limit. Note 3: The test trace is same as the ambient noise (the test frequency range: 9 kHz ~ 30 MHz and 18 GHz ~ 25 GHz), therefore no data appear in the report. FCC ID: 2ANKDJCHR35H5 Page Number: 20 of 34

Report No.: 1809WSU006-U1 Product RF Remote control Temperature 25°C Test Engineer Ternence Wang Relative Humidity 52% Test Site AC1 Test Date 2018/09/07 Remark: Harmonics Radiated Emission - 2479MHz Frequency Reading Factor Duty Cycle Measure Limit Margin Detector Polarization (MHz) Level (dB) Factor Level (dBμV/m) (dB) (dBμV) (dB) (dBμV/m) 39.2 0.5 14.5 N/A 15.1 40.0 -24.9 QP Horizontal 123.2 2.6 13.4 N/A 16.0 43.5 -27.5 QP Horizontal 39.2 0.5 14.5 N/A 15.1 40.0 -24.9 QP Vertical 123.5 5.7 13.5 N/A 19.1 43.5 -24.4 QP Vertical 4958.0 39.8 6.1 N/A 45.9 74.0 -28.1 PK Horizontal 7437.0 35.2 12.9 N/A 48.1 74.0 -25.9 PK Horizontal 9916.0 33.3 16.6 N/A 50.0 74.0 -24.0 PK Horizontal 12395.0 34.1 17.2 N/A 51.3 74.0 -22.7 PK Horizontal 4958.0 39.6 6.1 N/A 45.7 74.0 -28.4 PK Vertical 7437.0 34.1 12.9 N/A 46.9 74.0 -27.1 PK Vertical 9916.0 34.2 16.6 N/A 50.8 74.0 -23.2 PK Vertical 12395.0 34.5 17.2 N/A 51.7 74.0 -22.3 PK Vertical Note 1: Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Average Measure Level = Peak Measure Level + Duty Cycle Factor Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) – Pre Amplifier Gain (dB) Note 2: Average measurement was not performed when the peak level lower than average limit. Note 3: The test trace is same as the ambient noise (the test frequency range: 9 kHz ~ 30 MHz and 18 GHz ~ 25 GHz), therefore no data appear in the report. FCC ID: 2ANKDJCHR35H5 Page Number: 21 of 34

Report No.: 1809WSU006-U1 7.4. Radiated Restricted Band Edge Measurement 7.4.1.Test Limit For 15.205 requirement: Radiated emissions which fall in the restricted bands, as defined in Section 15.205(a) of FCC part 15, must also comply with the radiated emission limits specified in Section 15.209(a). Frequency Frequency Frequency Frequency (MHz) (MHz) (MHz) (GHz) 0.090 - 0.110 16.42 - 16.423 399.9 - 410 4.5 - 5.15 1 0.495 - 0.505 16.69475 - 16.69525 608 - 614 5.35 - 5.46 2.1735 - 2.1905 16.80425 - 16.80475 960 - 1240 7.25 - 7.75 4.125 - 4.128 25.5 - 25.67 1300 - 1427 8.025 - 8.5 4.17725 - 4.17775 37.5 - 38.25 1435 - 1626.5 9.0 - 9.2 4.20725 - 4.20775 73 - 74.6 1645.5 - 1646.5 9.3 - 9.5 6.215 - 6.218 74.8 - 75.2 1660 - 1710 10.6 - 12.7 6.26775 - 6.26825 108 - 121.94 1718.8 - 1722.2 13.25 - 13.4 6.31175 - 6.31225 123 - 138 2200 - 2300 14.47 - 14.5 8.291 - 8.294 149.9 - 150.05 2310 – 2390 15.35 - 16.2 8.362 - 8.366 156.52475 - 156.525 2483.5 - 2500 17.7 - 21.4 8.37625 - 8.38675 156.7 - 156.9 2690 - 2900 22.01 - 23.12 8.41425 - 8.41475 162.0125 - 167.17 3260 - 3267 23.6 - 24.0 12.29 - 12.293 167.72 - 173.2 3332 - 3339 31.2 - 31.8 12.51975 - 12.52025 240 - 285 3345.8 - 3358 36.43 - 36.5 12.57675 - 12.57725 322 - 335.4 3600 - 4400 (2) 13.36 - 13.41 -- -- -- FCC ID: 2ANKDJCHR35H5 Page Number: 22 of 34

Report No.: 1809WSU006-U1 All out of band emissions appearing in a restricted band as specified in Section 15.205 of the Title 47 CFR must not exceed the limits shown in Table per Section 15.209. FCC Part 15 Subpart C Paragraph 15.209 Frequency [MHz] Field Strength [uV/m] Measured Distance [Meters] 0.009 ~ 0.490 2400/F (kHz) 300 0.490 ~ 1.705 24000/F (kHz) 30 1.705 ~ 30 30 30 30 ~ 88 100 3 88 ~ 216 150 3 216 ~ 960 200 3 Above 960 500 3 7.4.2.Test Setup 1GHz ~ 18GHz Test Setup: FCC ID: 2ANKDJCHR35H5 Page Number: 23 of 34

Report No.: 1809WSU006-U1 7.4.3.Test Result Site: AC1 Time: 2018/09/07 - 23:21 Limit: FCC_Part15.209_RE(3m) Engineer: Messiah Li Probe: BBHA9120D_1-18GHz Polarity: Horizontal EUT: RF Remote control Power: By Battery Test Mode: Transmit at low channel 2404MHz No Flag Mark Frequency Reading Factor Duty Measure Limit Over Limit Type (MHz) Level (dB) Cycle Level (dBuV/m) (dB) (dBuV) Factor (dBuV/m) (dB) 1 2374.386 27.629 32.349 N/A 59.978 74.000 -14.022 PK 2374.386 27.629 32.349 -17.39 42.588 54.000 -11.412 AV 2 2390.000 25.839 32.327 N/A 58.166 74.000 -15.834 PK 2390.000 25.839 32.327 -17.39 40.776 54.000 -13.224 AV 3 2400.000 33.943 32.309 N/A 66.252 74.000 -7.748 PK 2400.000 33.943 32.309 -17.39 48.862 54.000 -5.138 AV 4 * 2403.982 58.436 32.301 N/A 90.737 114.000 -23.263 PK Note: Peak Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Average Measure Level = Peak Measure Level + Duty Cycle Factor Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) FCC ID: 2ANKDJCHR35H5 Page Number: 24 of 34

Report No.: 1809WSU006-U1 Site: AC1 Time: 2018/09/07 - 23:32 Limit: FCC_Part15.209_RE(3m) Engineer: Messiah Li Probe: BBHA9120D_1-18GHz Polarity: Vertical EUT: RF Remote control Power: By Battery Test Mode: Transmit at low channel 2404MHz No Flag Mark Frequency Reading Factor Duty Measure Limit Over Limit Type (MHz) Level (dB) Cycle Level (dBuV/m) (dB) (dBuV) Factor (dBuV/m) (dB) 1 2385.509 26.066 32.333 N/A 58.399 74.000 -15.601 PK 2385.509 26.066 32.333 -17.39 41.009 54.000 -12.991 AV 2 2390.000 24.092 32.327 N/A 56.419 74.000 -17.581 PK 2390.000 24.092 32.327 -17.39 39.029 54.000 -14.971 AV 3 2400.000 25.358 32.309 N/A 57.667 74.000 -16.333 PK 2400.000 25.358 32.309 -17.39 40.277 54.000 -13.723 AV 4 * 2403.982 43.583 32.301 N/A 75.884 114.000 -38.116 PK Note: Peak Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Average Measure Level = Peak Measure Level + Duty Cycle Factor Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) FCC ID: 2ANKDJCHR35H5 Page Number: 25 of 34

Report No.: 1809WSU006-U1 Site: AC1 Time: 2018/09/07 - 23:52 Limit: FCC_Part15.209_RE(3m) Engineer: Messiah Li Probe: BBHA9120D_1-18GHz Polarity: Horizontal EUT: RF Remote control Power: By Battery Test Mode: Transmit at high channel 2479MHz No Flag Mark Frequency Reading Factor Duty Measure Limit Over Limit Type (MHz) Level (dB) Cycle Level (dBuV/m) (dB) (dBuV) Factor (dBuV/m) (dB) 1 * 2479.024 58.041 32.322 N/A 90.363 114.000 -23.637 PK 2 2483.500 33.913 32.340 N/A 66.253 74.000 -7.747 PK 2483.500 33.913 32.340 -17.39 48.863 54.000 -5.137 AV 3 2483.968 34.247 32.341 N/A 66.588 74.000 -7.412 PK 2483.968 34.247 32.341 -17.39 49.198 54.000 -4.802 AV Note: Peak Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Average Measure Level = Peak Measure Level + Duty Cycle Factor Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) FCC ID: 2ANKDJCHR35H5 Page Number: 26 of 34

Report No.: 1809WSU006-U1 Site: AC1 Time: 2018/09/07 - 23:55 Limit: FCC_Part15.209_RE(3m) Engineer: Messiah Li Probe: BBHA9120D_1-18GHz Polarity: Vertical EUT: RF Remote control Power: By Battery Test Mode: Transmit at high channel 2479MHz No Flag Mark Frequency Reading Factor Duty Measure Limit Over Limit Type (MHz) Level (dB) Cycle Level (dBuV/m) (dB) (dBuV) Factor (dBuV/m) (dB) 1 * 2479.012 51.635 32.322 N/A 83.957 114.000 -30.043 PK 2 2483.500 26.400 32.340 N/A 58.740 74.000 -15.260 PK 2483.500 26.400 32.340 -17.39 41.350 54.000 -12.650 AV 3 2484.352 28.569 32.342 N/A 60.911 74.000 -13.089 PK 2484.352 28.569 32.342 -17.39 43.521 54.000 -10.479 AV Note: Peak Measure Level (dBμV/m) = Reading Level (dBμV) + Factor (dB) Average Measure Level = Peak Measure Level + Duty Cycle Factor Factor (dB) = Cable Loss (dB) + Antenna Factor (dB/m) FCC ID: 2ANKDJCHR35H5 Page Number: 27 of 34

Report No.: 1809WSU006-U1 7.5. 20dB Spectrum Bandwidth Measurement 7.5.1.Test Limit Intentional radiators must be designed to ensure that the 20 dB bandwidth of the emission in the specific band (2400 ~ 2483.5MHz). 7.5.2.Test Procedure used ANSI C63.10 Clause 6.9.2 7.5.3.Test Setting 1. Set the spectrum span range to overlap the nominal center frequency 2. Set RBW = 100 kHz 3. VBW ≥ 3 × RBW 4. Detector = Peak 5. Trace mode = max hold 6. Sweep = auto couple 7. Allow the trace was allowed to stabilize and marker the highest level. 8. Determine the display level (the highest level - 20dB) and place two markers, one at the lowest frequency and the other at the highest frequency. 7.5.4.Test Setup FCC ID: 2ANKDJCHR35H5 Page Number: 28 of 34

Report No.: 1809WSU006-U1 7.5.5.Test Result Product RF Remote control Temperature 24°C Test Engineer Ternence Wang Relative Humidity 59% Test Site TR3 Test Date 2018/09/08 Frequency Frequency Range Frequency Range Result (MHz) (MHz) (MHz) 2404 2403.31 --- Pass 2479 --- 2479.63 Pass 20dB Spectrum Bandwidth Measurement 2404 MHz 2479 MHz FCC ID: 2ANKDJCHR35H5 Page Number: 29 of 34

Report No.: 1809WSU006-U1 7.6. 99% Bandwidth Measurement 7.6.1.Test Limit N/A 7.6.2.Test Procedure used ANSI C63.10 Section 6.9 7.6.3.Test Setting 1. The analyzers’ automatic bandwidth measurement capability was used to perform the 99% bandwidth measurement. The bandwidth measurement was not influenced by any intermediated power nulls in the fundamental emission. 2. RBW = approximately 1% to 5% of the OBW. 3. VBW ≥ 3 × RBW. 4. Detector = Peak. 5. Trace mode = max hold. 7.6.4.Test Setup FCC ID: 2ANKDJCHR35H5 Page Number: 30 of 34

Report No.: 1809WSU006-U1 7.6.5.Test Result Product RF Remote control Temperature 24°C Test Engineer Ternence Wang Relative Humidity 59% Test Site TR3 Test Date 2018/09/08 Frequency (MHz) 99% Bandwidth (MHz) 2404 1.16 2454 1.08 2479 1.06 99% Occupied Bandwidth 2404 MHz 2454 MHz 2479 MHz FCC ID: 2ANKDJCHR35H5 Page Number: 31 of 34

Report No.: 1809WSU006-U1 8. CONCLUSION The data collected relate only the item(s) tested and show that the device is in compliance with Part 15C of the FCC Rules. The End FCC ID: 2ANKDJCHR35H5 Page Number: 32 of 34

Report No.: 1809WSU006-U1 Appendix A – Test Setup Photograph Refer to “1809WSU006-UT” file. FCC ID: 2ANKDJCHR35H5 Page Number: 33 of 34

Report No.: 1809WSU006-U1 Appendix B – EUT Photograph Refer to “1809WSU006-UE” file. FCC ID: 2ANKDJCHR35H5 Page Number: 34 of 34


Document Created: 2018-10-11 17:14:49
Document Modified: 2018-10-11 17:14:49
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC