test report

FCC ID: 2ANHI-P18

Test Report

Download: PDF
FCCID_4382513

Shenzhen B CTC Testing Co., Ltd. Report No.: BCTC-LH190600353E FCC Part 15C Test Report FCC ID:2ANHI-P18 Product Name: Dog Training Collar Trademark: N/A Model Name : P18 Prepared For : Shenzhen Smart Pet Technology Co., Ltd Floor 3, B Building, No. 25, Xingda Road, Egongling Community, Pinghu Address : Street, Longgang District, Shenzhen, Guangdong, China Prepared By : Shenzhen BCTC Testing Co., Ltd. BCTC Building & 1-2F, East of B Building, Pengzhou Industrial, Fuyuan 1st Address : Road, Qiaotou Community, F uyong Street, Bao’an District, Shenzhen, China Test Date: Jun. 17, 2019 to Jul. 02, 2019 Date of Report : Jul. 02, 2019 Report No.: BCTC-LH190600353E

@ tealtelnl BGTGTEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC—LH1 90600353E VERIFICATION OF COMPLIANCE Applicant‘s name ........ Shenzhen Smart Pet Technology Co., Ltd AQUF@SS ... Floor 3, B Building, No. 25, Xingda Road, Egongling Community, Pinghu Street, Longgang District, Shenzhen, Guangdong, China Manufacture‘s Name——. Shenzhen Smart Pet Technology Co., Lid AUUF@SS ... cce Floor 3, B Building, No. 25, Xingda Road, Egongling Community, Pinghu Street, Longgang District, Shenzhen, Guangdong, China Product description Product name................ Dog Training Collar Trademark: N/A Model Name: P18 FCC Part15.231 Test Standards: ANSI C63.10—2013 This device described above has been tested by BCTC, and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of BCTC, this document may be altered or revised by BCTC, personal only, and shall be noted in the revision of the document. TeSt RBSU.. .....2 .cc ceeeeermerereee Pass Prepared by(Engineer): Leke Xie Reviewer(S upervisor): Eric Yang Approved(Manager): Zero Zhou Test Report Tel:; 400—788—9558 Web: https /Avww.bctc—lab.com BCTC/RF—EMC—007 Ver.: A.0 Page 2 of 31

(Q) tealten BCTC TEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E Table of Contents Page 1 . SUMMARY OF TEST RESULTS a 1.1 TEST FACILITY o 1.2 MEASUREMENT UNCERTAINTY o . GENERAL INFORMATION ~ 2.1 GENERAL DESCRIPTION OF EUT ~ 2.2 DESCRIPTION OF TEST MODES o 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED o 2.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) c 2.5 EQUIPMENTS LIST FOR ALL TEST TEMS © 3. EMC EMISSION TEST e O 3.1 CONDUCTED EMISSION MEASUREMENT ekook ob ob ob eb oa 122 12 5 — 0 0 3.1.1 POWER LINE CONDUCTED EMISSION LIMITS 3.1.2 TEST PROCEDURE 3.1.3 DEVIATION FROM TEST STANDARD 3.1.4 TEST SETUP 3.1.5 EUT OPERATING CONDITIONS 3.1.6 TEST RESULTS 3.2 RADIATED EMISSION MEASUREMENT abock ob ob eb ok & O B t N N 3.2.1 RADIATED EMISSION LIMITS 3.2.2 TEST PROCEDURE 3.2.3 TEST SETUP 3.2.4 EUT OPERATING CONDITIONS 3.2.5 TEST RESULTS 4 . BANDWIDTH TEST NJ to 4.1 APPLIED PROCEDURES / LIMIT No NoN N N N B t 0 t t t 4.1.1 TEST PROCEDURE 4.1.2 DEVIATION FROM STANDARD 4.1.3 TEST SETUP 4.1.4 EUT OPERATION CONDITIONS 4.1.5 TEST RESULTS 5 . CALCULATION OF AVERAGE FACTOR No in 6 . DWELL TIME n on n N NNN N 6.1 DEVIATION FROM STANDARD 6.2 TEST SETUP 6.3 EUT OPERATION CONDITIONS Test Report Tel: 400—788—9558 Web: https Awww.bctc—lab.com BCTC/RF—EMC—007 \er: A.0 Page 3 of 31

(Q) tamltanl BCTC TEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E Table of Contents Page 6.4 TEST RESULTS 28 7 . ANTENNAREQUIREMENT 29 7.1 STAND ARD REQUIREMENT 29 7.2 EUT ANTENNA 29 8 . EUT TEST PHOTO 30 9 . EUT PHOTO 31 APPENDIX—PHOTOGRAPHS OF EUT CONSTRUCTIONAL DETAILS Test Report Tel: 400—788—9558 Web: https Awww.bctc—lab.com BCTC/RF—EMC—007 \Ver: A.0 Page 4 of 31

(Q) tamltanl BCTC TEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E 1. SUMMARY OF TEST RESULTS Test procedures according to the technical standards: FCC Part15 (15.231), Subpart C Standard Section Test tem Judgment Remark 15.207 Conducted Emision N/A Fundamental &Radiated Spurious Emission 15.209,15.231b PA 09. Meas urement SS 15.231c Occupy Bandwidth PASS 15.231a Dwell time PASS 15.203 Antenna Requirement PASS NOTE: (1)" N/A" denotes test is not applicable in this Test Report Test Report Tel: 400—788—9558 Web: https Awww.bctc—lab.com BCTC/RF—EMC—007 \er: A.0 Page 5 of 31

(Q) tamltanl BCTC TEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E 1.1 TEST FACILITY Shenzhen BCTC Testing Co., Ltd. Add.: BCTC Building & 1—2F, East of B Building, Pengzhou Industrial, Fuyuan 1st Road, Qiactou Community, Fuyong Street, Bac‘an District, Shenzhen, China FCC Test Firm Registration Number: 712850 IC Registered No.: 23583 1.2 MEASUREMENT UNCERTAINTY The reported uncertainty of measurement y * U > where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2 > providing a level of confidence of approximately 95 % > No. ktem Uncertainty 3m camber Radiated spurious _ 1 emission(3OMHz—1 GHz) U=4.3dB 3m chamber Radiated spurious 2 emission(1GHz—18GHz) U=4.5dB 3m chamber Radiated spurious _ 3 emission(18GHz—40GHz) U=3.340B A Conducted Adjacent channel U=1.38dB power Conducted output power _ 5 uncertainty Above 1G U=1.570dB Conducted output power _ 6 uncertainty below 1G U=1.28dB 7 humidity uncertainty U=5.3% 8 Temperature uncertainty U=0.59°C Test Report Tel: 400—788—9558 Web: https Awww.bctc—lab.com BCTC/RF—EMC—007 \er: A.0 Page 6 of 31

&us Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E 2. GENERAL INFORMATION 21 GENERAL DESCRIPTION OF EUT Equipment Dog Training Collar Trade Name N/A Model Name P18 Serial Model N/A Model Difference N/A Operation Frequency: 1433.92MHz Modulation Type: ASK Antenna Type: Spring Antenna Product Description — Antenna Gain: 10Bi Based on the application, features, or specification exhibited in User‘s Manual, the EUT is considered as an ITE/Computing Device. More details of EUT technical specification, please refer to the User‘s Manual. Ratings DC 3./1V Connecting VO Port(s) Please refer to the User‘s Manual hardware version N/A Software version N/A Serial number N/A Note: 1. For a more detailed features description, please refer to the manufacturer‘s specifications or the User‘s Manual. Test Report Tel: 400—788—9558 Web: https Awww.bctc—lab.com BCTC/RF—EMC—007 \Ver: A.0 Page 7 of 31

&s 2.2 DESCRIPTION OF TEST MODES Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E For All Emission Final Test Mode Description Mode 1 TX Mode Note: (1) Fully—charged battery is used during the test 2.3 BLOCK DIGRAM SHOWING THE CONFIGURATION OF SYSTEM TESTED Spurious emissions E—1 EUT 2.4 DESCRIPTION OF SUPPORT UNITS(CONDUCTED MODE) The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. kem Equipment Mr/Brand ModeV/TypeNo.| Series No. Note E—1 [Dog Training Collar N/A P18 N/A EUT Note: (1) The support equipment was authorized by Declaration of Confirmation. (2) For detachable type VO cable should be specified the length in cm in "Length 4 column. (3) "YES" is means "shielded" "with core"; "NO" is means "unshielded" "without core". Test Report Tel: 400—788—9558 Web: https Awww.bctc—lab.com BCTC/RF—EMC—007 \er: A.0 Page 8 of 31

C tealtan BCTCTEST Shenzhen BCTC Testing Co., Ltd. 25 EQUIPMENTS LIST FOR ALL TEST MEMS Report No.: BCTG—LH190600353E Radiation Test equipment ; . Last ; . kem Equipment Manufacturer Type No. Serial No. calibration Calibrated until Spectrum 1 Analyzer Agilent E4407B MY45109572 2019.06.13 2020.06.12 (OkHz—26.5GHz) Test Receiver 2 (OKHz—7GHz) R&S ESR7 101154 2019.06.13 2020.06.12 Bilog Antenna |SCHWARZBE VULBI163—94 3 (30MHz—3GHz) CK VULB9163 > 2019.06.13 2020.06.12 Horn Antenna SCHWARZBE 4 (1GHz—18GHz) CK BBHAQ120D 1541 2019.06.13 2020.06.12 Horn Antenna SCHWARZBE 5 (18GHz—40GHz) CK BBHAQ170 822 2019.06.13 2020.06.12 Amplifier SCHWARZBE 6 (IKHz—6GHz) CK BBV9744 9744—0037 2019.06.13 2020.06.12 Amplifier SCHWARZBE _ 7 (0.5GHz—18GHz) CK BBV9718 9718—309 2019.06.13 2020.06.12 Amplifier TTA1840—35— 8 (18GHz—40GHz) MITEQ HG 2034381 2019.06.13 2020.06.12 Loop Antenna —|SCHWARZBE 9 (OKHz—30MHz) CK FMZB1519B 014 2019.06.17 2020.0616 RF cables1 B1702988—000 10 (OkHz—30MH2z) Huber+Suhnar 9kHz—30MHz 8 2019.06.17 2020.0616 RF cables2 11 (30MHz—1GHz) Huber+Suhnar |[30MHz—1GHz| 1486150 2019.06.17 2020.0616 RF cables3 12 (1GHz—40GHz) Huber+Suhnar |1GHz—40GHz 1607106 2019.06.17 2020.0616 13 Power Metter Keysight E4419 \ 2019.06.17 2020.0616 14 P°""T;\Sl)e”50r Keysight E9 300A \ 2019.06.17 2020.0616 Signal Analyzer 15 POkHz—26.5GHz KEYSIGHT N9020A MY49100060 2019.06.13 2020.06.12 Spectrum 16 Analyzer Aglient FSP40 100363 2019.06.13 2020.0612 9kHz—40GHz D.C. Power . 17 Supply LongWei TPR—6405D \ \ \ 18 Software Frad EZ—EMC FA—O3A2 RE \ \ Test Report Tel: 400—788—9558 Web: https Awww.bctc—lab.com BCTC/RF—EMC—007 \er: A.0 Page 9 of 31

C tealtan BCTCTEST Conduction Test equipment Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E kem Equipment Manufacturer Type No. Serial No. Last calibration Ca{flfited 1 Test Receiver R&s ESR3 102075 2019.06.13 2020.06.12 2 usn |SCHWARZBEO) meixgi27 s1277se 2019.0613 2020.06.12 3 LISN R&S ENV216 101375 2019.06.13 2020.06.12 4 RF cables Huber+Suhnar 9kHz—30MHz B170%9888'00 2019.06.25 2020.06.24 5 Software Frad ezeme EM§CON \ \ 3. EMC EMISSION TEST 3.1 CONDUCTED EMISSION MEASUREMENT 3.1.1 POWER LINE CONDUCTED EMISSION Limits (Frequency Range 150KHz—30MHz) Limit (dBuV) FREQU NCY (MHz) — Standard Quasi—peak Average 0.15 —0.5 66 — 56 * 56 — 46 * FCC 0.50 —5.0 56.00 46.00 FCC 5.0 —30.0 60.00 50.00 FCC Note: (1) The tighter limit applies at the band edges. (2) The limit of " * " marked band means the limitation decreases linearly with the logarithm of the frequency in the range. The following table is the setting of the receiver Receiver Parameters Setting Attenuation 10 dB Start Frequency 0.15 MHz Stop Frequency 30 MHz IF Bandwidth 9 kHz Test Report Tel: 400—788—9558 Web: https Awww.bctc—lab.com BCTC/RF—EMC—007 \Ver: A.0 Page 10 of 31

(Q) tamltanl BCTC TEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E 3.1.2 TEST PROCEDURE a. The EUT was placed 0.8 meters from the horizontal ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long. c. /O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. d. LISN at least 80 cm from nearest part of EUT chassis. e. For the actualtest configuration, please refer to the related Item —EUT Test Photos. 3.1.3 DEVIATION FROM TEST STANDARD No deviation 3.1.4 TEST SETUP Vertical Reference Ground Plane Test Receiver EC___—I3 o o o o EUT M“" o e o o || s0cm || 1 1 11 N 1— \ Horizontal Reference Ground Plane Note: 1.Support uniis were connected to second LISN. 2.60th of LISNs (AMN) are 80 ocm from EUT and at least 80 from other units and other metal planes 3.1.5 EUT OPERATING CONDITIONS The EUT was configured for testing in a typical fashion (as a customer would normally use it}. The EUT has been programmed to continuously transmit during test. This operating condition was tested and used to collect the included data. 3.1.6 TEST RESULTS NOTE: This EUT is powered by the battery only, this test item is not applicable. Test Report Tel: 400—788—9558 Web: htips Awww.bctc—lab.com BCTC/RF—EMC—007 Ver: A.0 Page 11 of 31

&us Shenzhen BCTC Testing Co., Ltd. 3.2 RADIATED EMISSION MEASUREMENT Report No.: BCTC—LH190600353E 3.2.1 RADIATED EMISSION LIMITS (Frequency Range 9kHz—1000MHz) 20dBc in any 100 kHz bandwidth outside the operating frequency band. In case the emission fall within the restricted band specified on 15.205(a), then the 15.231(b) limit in the table below has to be followed. Frequencies(MHz) Field Strength{micorvolts/meter) Measurement Distance(meters) 0.009~0.490 2400/F(KHz) 300 0.490~1.705 24000/F(KHz) 30 1.705~30.0 30 30 30~88 100 3 88~216 150 3 216~960 200 3 Above 960 500 3 LIMITS OF RADIATED EMISSION MEASUREMENT (Above 1000MHz) Limit (dBuV/m) (at 3M) FREQUENCY (MHz) PEAK AVERAGE Above 1000 74 54 Notes: (1) The limit for radiated test was performed according to FCC PART 15C. (2) The tighter limit applies at the band edges. (3) Emission level (dBuV/m)=20l0g Emission level (uV/m). FUNDAMENTAL AND HARMONICS EMISSION LIMITS Fundamental Field Strength of Field Strength of Frequency Fundamental Spurious Emissions (MHz) (microvolts/meter) (microvolts/meter) 40.66 — 40.70 2,.250 225 70 — 130 1,250 125 130 — 174 1.250 to 3.750 ** 125 to 375 ** 174 — 260 3.750 375 260 — 470 3.750 to 12.500 ** 375 to 1.250 ** Above 470 12.500 1,250 ** linear interpolations [Where F is the frequency in MHz, the formulas for calculating the maximum permitted fundamental field strengths are as follows: for the band 130—174 MHz, pV/im at 3 meters = 56.81818(F) — 6136.3636; for the band 260—470 MHz, pV/im at 3 meters = 41.6667(F) — 7083.3333. The maximum permitted unwanted emission level is 20 dB below the maximum permitted fundamental level.] Test Report Tel: 400—788—9558 Web: htips /Avww.bctc—lab.com BCTO/RF—EMC—007 \er.: A.0 Page 12 of31

(Q) tealten BCTC TEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E FREQUENCY RANGE OF RAD IATED MEASUREMENT (For unintentional radiators) Highest frequency generated or Upper frequency of measurement used in the device or on which Range (MHz) the device operates or tunes (MHz) Below 1.705 30 1.705— 108 1000 108 — 500 2000 500 — 1000 5000 th i i Above 1000 5" harmonic ofwficmgi\:grsgrlgevu;ncy or 40 GHz, Spectrum Parameter Setting Attenuation Auto Start Frequency 1000 MHz Stop Frequency 10th carrier harmonic RBW / VBW setting 1 MHz /1 MHz for Peak, 1 MHz / 10Hz for Average Receiver Parameter Setting Attenuation Auto Start ~ Stop Frequency OkHz~150kHz / RB 200Hz for QP Start ~ Stop Frequency 150kHz~30MHz / RB 9kHz for QP Start ~ Stop Frequency 30MHz~1000MHz / RB 120kHz for QP 3.2.2 TEST PROCEDURE a. The measuring distance of at 3 m shall be used for measurements at frequency up to 1GHz. For frequencies above 1 GHz, any suitable measuring distance may be used. b. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter open area test site. The table was rotated 360 degrees to determine the position of the highest radiation. . The height of the equipment or of the substitution antenna shall be 0.8 m; above 1GHz, the height was 1.5m, the height of the test antenna shall vary between 1 m to 4 m. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. The initial step in collecting conducted emission data is a spectrum analyzer peak detector mode pre—scanning the measurement frequency range. Significant peaks are then marked and then Quasi Peak detector mode re—measured. e. If the Peak Mode measured value compliance with and lower than Quasi Peak Mode Limit, the EUT shall be deemed to meet QP Limits and then no additional QP Mode measurement performed. f. For the actual test configuration, please refer to the related ftem —EUT Test Photos. Note: Both horizontal and vertical antenna polarities were tested and performed pretest to three orthogonal axis. The worst case was X axis and the emissions were reported Test Report Tel: 400—788—9558 Web: htips Awww.bctc—lab.com BCTC/RF—EMC—007 Ver: A.0 Page 13 of 31

@ tamltanl BCTC TEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E 3.2.3 TEST SETUP (A) Radiated Emission Test—Up Frequency Below 30MHz $ 1 ] m— 3m —»i Turntable 1m to 4m Spectrum \ ________ Analyzer —‘_r IO 8m | a ____—— Ground Plane Coaxial Cable Test Report Tel: 400—788—9558 Web: https Awww.bctc—lab.com BCTC/RF—EMC—007 Ver: A.0 Page 14 of 31

&us Shenzhen BCTC Testing Co., Ltd. (C) Radiated Emission Test—Up Frequency Above 1 GHz Report No.: BCTG—LH190600353E Turntable 3m X Spectrum Analyzer Ground Plane A Coaxial Cable 3.2.4 EUT OPERATING CONDIT IONS The EUT tested system was configured as the statements of 2.4 Unless otherwise a special operating condition is specified in the follows during the testing. Test Report Tel: 400—788—9558 Web: https Awww.bctc—lab.com BCTC/RF—EMC—007 Ver: A.0 Page 15 of 31

(Q) tamltanl BCTC TEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E 3.2.5 TEST RESULTS Radiated Spurious Emission (Below 9KHz — 30MHz ) Temperature : 26 °C Relative Humidity : 54% Pressure : 101 kPa Polarization : Test Voltage :_ JDC 3.7V Test Mode : TX Mode Freq. Reading Limit Margin State (MHz) (dBuV/im) (dBuV/im) (dB) P/F —— —— —— —— PASS —— —— —— —— PASS NOTE: The amplitude of spurious emissions which are attenuated by more than 20dB below the permissible value has no need to be reported. Distance extrapolation factor =40 log (specific distance/test distance)(dB); Limit line = specific limits(dBuv) + distance extrapolation factor. Test Report Tel: 400—788—9558 Web: https Awww.bctc—lab.com BCTC/RF—EMC—007 Ver: A.0 Page 16 of 31

@&: fealten BCTCTEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E Radiated Spurious Emission (Between 30MHz — 1GHz) Temperature : 26 °C Relative Humidity : 54% Pressure : 101 kPa Polarization : Horizontal Test Voltage DC 3.7V Test Mode TX Mode Frequency Meter Reading Factor Emission Level Limils Margin Detector Type (MHz) (dBuV) (dB) (dBuVim) (dBuVim) (dB) 57.5938 26.40 ~15.65 10.75 40.00 <29.25 aP 102.3597 25.02 ~16.43 8.59 43.50 —34.91 aP 199.2855 30.37 —16.35 14.02 43.50 —29.48 aP 329.0390 53.83 ~12.80 41.03 46.00 4.97 aP 361.7139 46.10 —11.96 34.14 46.00 ~11.86 aP 433.9221 90.29 —~10.33 79.96 100.8 —20.84 peak 541.3724 40.30 —7.90 32.40 46.00 ~13.60 aP 867.8692 30.13 213 28.00 80.8 —52.80 peak Remark: Factor = Antenna Factor + Correct Factor. Correct Factor= Cable Loss — Pre—amplifier 80.0 dBu¥/m 0_ 6 _ FCC 433 QP Margin —6.dB 40 & 7 8 fl' M ferie! mww w,.h a. U«“"y W "‘\W\.\*\, 30.000 40 50 60 70 80 (MHz] 400 500 600 700 1000.000 Test Report Tel: 400—788—9558 Web: htips Jvww.betc—lab.com BCTC/RF—EMC—007 Ver: A.0 Page 17 of 31

Q faallt&0) < BGTC Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E Temperature : 26 °C Relative Humidity : 54% Pressure : 101 kPa Polarization : Vertical Test Voltage : |DC 3.7V Test Mode : TX Mode Frequency Meter Reading Factor Emission Level Limils Margin Detector Type (MHz) (dBuV) (dB) (dBuVim) (dBuVim) (dB) 35.0048 30.31 ~16.34 13.97 40.00 —26.03 aP 53.1313 26.22 ~15.18 11.04 40.00 —28.96 aP 89.5899 31.71 —18.19 13.52 43.50 —29.98 aP 196.5098 27.12 ~16.52 10.60 43.50 —32.90 aP 250.301 1 27.49 —15.14 12.35 46.00 —33.65 aP 331.3546 41.01 —12.74 28.27 46.00 ~17.73 aP 433.9261 79.10 —10.33 68.77 100.8 —32.03 peak 867.8333 29.21 213 27.08 80.8 —53.72 peak Remark: Factor = Antenna Factor + Correct Factor. Correct Factor= Cable Loss — Pre—amplifier 80.0 dBu¥/m e e FCC 433 @P Margin —6. 6B 40 8 8 e W‘A W"‘ io J’\}/%W 30.000 5o 60 70 80 (MHz) 400 500— 600 700 1000.000 Test Report Tel: 400—788—9558 Web: htips Awww.bctc—lab.com BCTC/RF—EMC—007 Ver: A.0 Page 18 of 31

(Q) tamltanl BCTC TEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E For average Emission Peak Duty Frequency AverageLevel Level cycle Limit Margin Polarization MHz dBuV/im dBuV/im factor AV 433.92 79.96 —8.64 71.32 80.8 —9.48 Horizontal 867.84 28.00 —8.64 19.36 60.8 —41.44 Horizontal Notes: 1. Average emission Level = Peak Level + Duty cycle factor 2.Duty cycle level please see clause 5. Peak Duty Frequency AverageLevel Level cycle Limit Margin Polarization MHz dBuV/im dBuV/im factor AV 433.92 68.77 —8.64 60.13 80.8 —20.67 Vertical 867.84 27.08 —8.64 18.44 60.8 —42.36 Vertical Notes: 1. Average emission Level = Peak Level + Duty cycle factor 2. Duty cycle level please see clause 5. Test Report Tel: 400—788—9558 Web: htips Awww.bctc—lab.com BCTC/RF—EMC—007 Ver: A.0 Page 19 of 31

(Q) tamltanl BCTC TEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E Radiated Spurious Emission ( 1GHz to 10°" harmonics}) Peak Duty Average Lim t Margin dB Frequency Level cycle Level Polarization MHz PK AV PK AV dBuV/im factor dBuV/m 1301.71 51.68 —8.64 43.04 80.8 60.8 |—29.12 —17.76 Vertical 1735.24 52.04 —8.64 43.40 80.8 60.8 |—28.76 —17.40 Vertical 2603.57 50.48 —8.64 41.84 80.8 60.8 |—30.32 —18.96 Vertical 3037.43 50.84 —8.64 42.20 80.8 60.8 |—29.96 —18.60 Vertical 3471.34 50.07 —8.64 41 43 80.8 60.8 |—30.73 —19.37 Vertical 3905.28 47.71 —8.64 39.07 80.8 60.8 |—33.09 —21.73 Vertical 1301.71 47.38 —8.64 38.74 80.8 60.8 |—33.42 —22.06 Horizontal 1735.24 47.25 —8.64 38.61 80.8 60.8 |—33.55 —22.19 Horizontal 2603.57 49.89 —8.64 41.25 80.8 60.8 |—30.91 —19.55 Horizontal 3037.43 49.11 —8.64 4047 80.8 60.8 |—31.69 —20.33 Horizontal 3471.34 47.24 —8.64 38.60 80.8 60.8 |—33.56 —22.20 Horizontal 3905.28 48.38 —8.64 39.74 80.8 60.8 |—32.42 —21.06 Horizontal Notes: 1.Average emission Level = Peak Level + Duty cycle factor 2.Duty cycle level please see clause 5. 3. Pulse Desensitization Correction Factor Pulse Width (PW) = 43.50ms 2/PW = 2/43.50ms =0.046 kHz RBW (100 kHz) > 2/PW (0.046kHz) Therefore PDCF is not needed 4.Other harmonics emissions are lower than 20dB below the allowable limit. Test Report Tel: 400—788—9558 Web: https Awww.bctc—lab.com BCTC/RF—EMC—007 \Ver: A.0 Page 20 of 31

@,} fln R BGTGTEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E CONDUCTED EMISSION MEASUREME NT 433.92MHz i AgrentSpectum rraer— svep sn Next Peak Next PKRight Next P Left] Marker Delta Mkr—CF Mkr—RefLyl More 1 or2 Start 9 kHz Stop 30.00 MHz #Res BW 100 kHz Sweep 2.867 ms (1001 pts) PNio.resr C0°Trig: FreeRun AvalHold:>100/100 IFGain:tow Atten: 10 dB Next Peak Next PKRight Next P Left] Marker Delta Mkr—CF Mkr—RefLyl More 1 or2 Bsns Stop 1.0000 GHz #Res BW 100 kHz #VBW 300 kHz Sweep 92.73 ms (1001 pts) use Test Report Tel: 400—788—9558 Web: htips /Ayww.bctc—lab.com BCTC/RF—EMC—007 Ver: A.0 Page 21 of 31

felf&l BCTCTEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E 433.92MHz ppppremmayremsenmeers _1e> sucn auto 109320 a0002 2019 se Marker 1 1.828000000000 GHz . Aug Type: Log.Pwr PNO:res C2). Trig: FreeRun AvalHold: 141100 IEGaindLow ~*—_ Atten: 10 dB Ref 0.00 dBm Start 1.000 GHz Stop 7.000 GHz #Res BW 100 kHz #VBW 300 kHz Sweep 573.5 ms (1001 pts) luse 1 File <PICTURE.PNG> saved Testams Test Report Tel: 400—788—9558 Web: htips /Ayww.bctc—lab.com BCTC/RF—EMC—007 Ver: A.0 Page 22 of 31

(Q) tamltanl BCTC TEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E 4. BANDWIDTH TEST 4.1 APPLIED PROCEDURES / LIMIT According to FCC 15.231(c) requirement: The bandwidth of the emission shall be no wider than 0.25% of the center frequency for devices operating between 70 MHz to 900 MHz. Those devices operating above 900 MHz, the emission spurious shall be no wider than 0.5% of the center frequency. Bandwidth is determined at the points 20 dB down from the modulated carrier. B.W (20dBc) Limit = 0.25% * f(MHz) = 0.25% * 433.92MHz = 1.0848MHz m Parameter tting Attenuation Auto Frequenc > Measurement Bandwidth or Channel Separation RB 3OkHz VB > Detector Peak Trace Max Hold Sw Time Auto 4.1.1 TEST PROCEDURE a. The EUT was directly connected to the spectrum analyzer and antenna output port as show in the block diagram below, b. Spectrum Setting : RBW= 30kHz, VBW>z RBW, Sweep time = Auto. 4.1.2 DEVIATION FROM STANDARD No deviation. 4.1.3 TEST SETUP EUT SPECTRUM ANALYZER 4.1.4 EUT OPERATION CONDIT IONS The EUT tested system was configured as the statements of 2.4 Unless otherwise a special operating condition is specified in the follows during the testing. Test Report Tel: 400—788—9558 Web: htips Awww.bctc—lab.com BCTC/RF—EMC—007 Ver: A.0 Page 23 of 31

C fellt&n BCTCTEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E 4.1.5 TEST RESULTS Temperature : 26 °C Relative Humidity : (54% Pressure : 101kPa Test Voltage DC 3.7V Test Mode TX Mode 200B Bandwidth Limit Frequency Result (KHz) (MHz) 433.9MHz 348.8 1.0848 PASS Mode 1 wucn auto 11327 an rloe, 2010 Span 2.0000 MHz Genter Freq: 435.200000 MHz Radio Std: None Aesppccce C2Y C Trig: FreeRun AvglHold:>»1010 #1EGain:Low #Atten: 10 4B Radio Device: BTS Ref 10.00 dBm VBW 300 kHz Occupied Bandwidth Looty —2.67 dBm 308.33 kHz Transmit Freq Error OeCsS OBW Power 99.00 % x dB Bandwidth 348.8 kHz x dB —20.00 dB Test Report Tel: 400—788—9558 Web: https /Avww.bctc—lab.com BCTC/REF—EMC—007 Ver: A.0 Page 24 of 31

(Q) im BGTGTEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E 5. CALCULATION OF AVERAGE FACTOR The output field strengths of specification in accordance with the FCC rules specify measurements with an average detector. During the test, a spectrum analyzer incorporating a peak detector was used. Therefore, a reduction factor can be applied to the resultant peak signal level and compared to the limit for measurement instrumentation incorporating an average detector. The duty cycle is measured in 100 ms or the repetition cycle period, whichever is a shorter time frame. The duty cycle is measured by placing the spectrum analyzer to set zero span at 100kHz resolution bandwidth. Averaging factor in dB =20log (duty cycle) The duration of one cycle =43.50ms The duty cycle is simply the on—time divided the duration of one cycle Duty Cycle = (0.910ms*10+0.310ms*23)/ 43.50 ms =16.23ms / 43.50ms =0.37 Therefore, the averaging factor is found by 2010g0.37=—8.640B Test plot as follows: Note: During the 100ms, the amount of pulse and on—time of pulse are the same for every pulse train. Cycle i rotertipectom ns sn —15 Es sucu abto Marker 1 A 43.5000 ms . Avg Type: Log.Pwr PNO:Fast ~»~ Trig: FreeRun IFGain:tow Atten: 10 dB Ref 0.00 dBm Center 433.920000 MHz Span 0 Hz CC utd VBW 3.0 MHz Sweep 150.0 ms (1001 pts) use Lstams Test Report Tel: 400—788—9558 Web: htips /Ayww.bctc—lab.com BCTC/RF—EMC—007 Ver: A.0 Page 25 of 31

(@fealienl BGTG Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E Pulse [E Agient Spectom Avair: suepi on TCTSkS aulcil auto 103602 A10ut05, 2019 Avg Type: Log—Pur ueccso PNO.ract «>= Trig: FreeRun s on Atten: 10 dB sele(:tTra(:e> 10 derdiv Ref 0.00 dBm i View BIank} Trace On esc Loo d i enmine sn e auciauto Marker 3 A 310 000 us . Avg Type: Log.Pwr PNO:Fast ~»~ Trig: FreeRun iGaintow Atten: 10 dB 10 dardiv Ref 0.00 dBm i Center 433.920000 MHz Span 0 Hz, Res BW 1.0 MHz VBW 3.0 MHz Sweep 5.000 ms (1001 pts) m move Tre s Fuxcron Fuxcronwom roxcronvae — 1m-n 910.0 us (A 1280dB 805.0 us #o64dBm| _______|_______|_______| nm-mmm B 230 aB]_______|_________ t]________2.000 Te27dBm|_______|_______|________| [LPPOR |nnpenmmmmneEnpenee Test Report Tel: 400—788—9558 Web: htips /Ayww.bctc—lab.com BCTC/RF—EMC—007 Ver: A.0 Page 26 of 31

(Q) tamltanl BCTC TEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E 6. DWELL TIME APPLIC ABLE STAND ARD According to FCC 15.231(a) requirement: A manually operated transmitter shall employ a switch that will automatically deactivate the transmitter within not more than 5 seconds of being released. TEST PROCEDURE a) Check the calibration of the measuring instrument using either an internal calibrator or a known signal from an external generator. C) Position the EUT without connection to measurement instrument. Turn on the EUT and connectits antenna terminal to measurement instrument via a low loss cable. Then set it to any one measured frequency within its operating range, and make sure the instrument is operated in its linear range. Set RBW to 100 kHz and VBW of spectrum analyzer to 300 kHz with a convenient frequency span including 100 kHz bandwidth from band edge. d) Measure the highest amplitude appearing on spectral display and set it as a reference level. Plot the graph with marking the highest point and edge frequency. e) Repeat above procedures until all measured frequencies were complete. 6.1 DEVIATION FROM STANDARD No deviation. 6.2 TEST SETUP EUT SPECTRUM ANALYZER 6.3 EUT OPERATION CONDITIONS The EUT tested system was configured as the statements of 2.4 Unless otherwise a special operating condition is specified in the follows during the testing. Test Report Tel: 400—788—9558 Web: https Awww.bctc—lab.com BCTC/RF—EMC—007 Ver: A.0 Page 27 of 31

(Q) im BGTGTEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E 6.4 TEST RESULTS Dwell time (second) Limit (second) Result 0.280s <5s Pass Test plot as follows: i RieGprtam meqrn sucu abto Marker 1 A 280.000 ms . Avg Type: LogPwr PNO: Fast ~»~ Trig: FreeRun IFGaintow Atten: 10 dB Ref 0.00 dBm oo es Res BW 1.0 MHz VBW 3.0 MHz plo eS is w wooe mre sat x Fonchonvrunchonwor 280.0 ms (A 203 4B)________| 100.0 ms T2.68 dBm|________| |npEe Test Report Tel: 400—788—9558 Web: htips /Ayww.bctc—lab.com BCTC/RF—EMC—007 Ver: A.0 Page 28 of 31

(Q) tamltanl BCTC TEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTG—LH190600353E 7. ANTENNA REQUIREMENT 7.1 STANDARD REQUIREMENT 15.203 requirement: For intentional device, according to 15.203: an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. 7.2 EUT ANTENNA The EUT antenna is the Spring Antenna. It comply with the standard requirement. Test Report Tel: 400—788—9558 Web: https Awww.bctc—lab.com BCTC/RF—EMC—007 Ver: A.0 Page 29 of 31

feltd BCTCTEST Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC—LH1 90600353E 8. EUT TEST PHOTO Radiated Measurement Photos Test Report Tel: 400—788—9558 Web: https /www.bctc—lab.com BCTC/RF—EMC—007 Ver.: A.0 Page 30 of 31

@ tEalleln BGTG Shenzhen BCTC Testing Co., Ltd. Report No.: BCTC—LH1 90600353E 9. EUT PHOTO 12 13 14 15 16 17 18 joofi on 415 d6 17 18| 19 20 21 22 : Iudulntulnt ul uodols ul 405060708 9 10 f1 1293 14 5 16 1 ulustul | KKXXX END OF REPORT KXXX Test Report Tel: 400—788—9558 Web: https /www.bctc—lab.com BCTC/RF—EMC—007 Ver.: A.0 Page 31 of 31


Document Created: 2019-07-31 07:59:29
Document Modified: 2019-07-31 07:59:29
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC