Test Report

FCC ID: 2ANDR-RXPRO11805

Test Report

Download: PDF
FCCID_3870613

FCC PART 15.407 RSS-GEN, ISSUE 4, NOVEMBER 2014 RSS-247, ISSUE 2, FEBRUARY 2017 TEST REPORT For SZ DJI Osmo Technology Co.,Ltd. 12th floor,West Wing,Skyworth Semiconductor Design Building NO.18 Gaoxin South 4th Ave, Nanshan District,Shenzhen,China FCC ID: 2ANDR-RXPRO11805 IC: 23060-RXPRO11805 Report Type: Product Name: Original Report DJI Pro Wireless Receiver Report Number: RDG180507002-00B Report Date: 2018-05-17 Jerry Zhang EMC Manager Reviewed By: Bay Area Compliance Laboratories Corp. (Dongguan) Test Laboratory: No.69 Pulongcun, Puxinhu Industry Area, Tangxia, Dongguan, Guangdong, China Tel: +86-769-86858888 Fax: +86-769-86858891 www.baclcorp.com.cn Note: This test report is prepared for the customer shown above and for the device described herein. It may not be duplicated or used in part without prior written consent from Bay Area Compliance Laboratories Corp. (Dongguan). This report must not be used by the customer to claim product certification, approval, or endorsement by A2LA* or any agency of the Federal Government. * This report may contain data that are not covered by the A2LA accreditation and are marked with an asterisk “*”.

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B TABLE OF CONTENTS GENERAL INFORMATION .......................................................................................................................................3 PRODUCT DESCRIPTION FOR EQUIPMENT UNDER TEST (EUT) .....................................................................................3 OBJECTIVE ...................................................................................................................................................................3 RELATED SUBMITTAL(S)/GRANT(S) .............................................................................................................................3 TEST METHODOLOGY ..................................................................................................................................................4 MEASUREMENT UNCERTAINTY ....................................................................................................................................4 TEST FACILITY .............................................................................................................................................................4 SYSTEM TEST CONFIGURATION ..........................................................................................................................5 DESCRIPTION OF TEST CONFIGURATION ......................................................................................................................5 EQUIPMENT MODIFICATIONS .......................................................................................................................................5 EUT EXERCISE SOFTWARE ..........................................................................................................................................5 SUPPORT EQUIPMENT LIST AND DETAILS ....................................................................................................................5 SUPPORT CABLE LIST AND DETAILS ............................................................................................................................6 BLOCK DIAGRAM OF TEST SETUP ................................................................................................................................6 SUMMARY OF TEST RESULTS ...............................................................................................................................7 FCC §15.407 (f) & §1.1310 & §2.1091- MAXIMUM PERMISSIBLE EXPOSURE (MPE) ........................................8 APPLICABLE STANDARD ..............................................................................................................................................8 RSS-102 § 2.5.2 - EXEMPTION LIMITS FOR ROUTINE EVALUATION – RF EXPOSURE EVALUATION ..............................................................................................................................................................9 APPLICABLE STANDARD ..............................................................................................................................................9 FCC §15.203 ,RSS-GEN§8.3- ANTENNA REQUIREMENT..................................................................................10 APPLICABLE STANDARD ............................................................................................................................................10 ANTENNA CONNECTOR CONSTRUCTION ....................................................................................................................10 FCC §15.209, §15.205 , §15.407(b) &RSS-247 §6.2, RSS-GEN§8.10–UNWANTED EMISSION .........................11 APPLICABLE STANDARD ............................................................................................................................................11 EUT SETUP ................................................................................................................................................................13 EMI TEST RECEIVER & SPECTRUM ANALYZER SETUP ..............................................................................................14 TEST PROCEDURE ......................................................................................................................................................15 CORRECTED AMPLITUDE & MARGIN CALCULATION .................................................................................................15 TEST EQUIPMENT LIST AND DETAILS .........................................................................................................................16 TEST DATA ................................................................................................................................................................16 Page 2 of 22

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B GENERAL INFORMATION Product Description for Equipment under Test (EUT) EUT Name: DJI Pro Wireless Receiver EUT Model: RXPRO1 FCC ID: 2ANDR-RXPRO11805 IC: 23060-RXPRO11805 Rated Input Voltage: DC 5V-15V External Dimension: 63 mm (L) x 38 mm (W) x19 mm (H) Serial Number: 180507002 EUT Received Date: 2018-05-07 Objective This type approval report is prepared on behalf of SZ DJI Osmo Technology Co.,Ltd. in accordance with Part 2-Subpart J, Part 15-Subparts A and E of the Federal Communications Commission’s rules. And RSS-247, Issue 2, February 2017, RSS-Gen Issue 4, November 2014 of the Innovation, Science and Economic Development Canada. The tests were performed in order to determine compliance with FCC Rules Part 15, Subpart E, section 15.203, 15.205, 15.209 and 15.407 rules, and RSS-247, Issue 2, February 2017, RSS-Gen Issue 4, November 2014 of the Innovation, Science and Economic Development Canada. The device`s RF board is identical with the certified device: Force Pro, model: P1F1, FCC ID: 2ANDR-P1F11803, IC: 23060-P1F11803, and the changes not related with the RF parameters. All antenna port conducted tests were reduced, and please refer to the P1F1 report. Related Submittal(s)/Grant(s) FCC submissions with Part 15.247 DSS, FCC ID: 2ANDR-RXPRO11805. ISEDC submissions with RSS-247 FHSs, IC: 23060-RXPRO11805. Part of system submissions with FCC ID: 2ANDR-RS11804,IC: 23060-RS11804; FCC ID:2ANDR-R21708,IC:23060-R21708. Page 3 of 22

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B Test Methodology All measurements detailed in this Test Report were performed in accordance with ANSI C63.10-2013 “American National Standard of Procedures for Compliance Testing of Unlicensed Wireless Devices”. RSS-247, Issue 2, February 2017, RSS-Gen Issue 4, November 2014 of the Innovation, Science and Economic Development Canada. And KDB 789033 D02 General U-NII Test Procedures New Rules v02r01 All emissions measurement was performed and Bay Area Compliance Laboratories Corp. (Dongguan). Measurement Uncertainty Parameter Measurement Uncertainty Occupied Channel Bandwidth ±5 % RF output power, conducted ±0.61dB Power Spectral Density, conducted ±0.61 dB 30M~200MHz: 4.58 dB for Horizontal, 4.59 dB for Vertical Unwanted Emissions, radiated 200M~1GHz: 4.83 dB for Horizontal, 5.85 dB for Vertical 1G~6GHz: 4.45 dB, 6G~40GHz: 5.23 dB Unwanted Emissions, Conducted ±1.5 dB Temperature ±1℃ Humidity ±5% DC and low frequency voltages ±0.4% Duty Cycle 1% AC Power Lines Conducted 3.12 dB (150 kHz to 30 MHz) Emission Test Facility The Test site used by Bay Area Compliance Laboratories Corp. (Dongguan) to collect test data is located on the No.69 Pulongcun, Puxinhu Industry Area, Tangxia, Dongguan, Guangdong, China. The test site has been approved by the FCC under the KDB 974614 D01 and is listed in the FCC Public Access Link (PAL) database, FCC Registration No. : 897218,the FCC Designation No. : CN1220. The test site has been registered with ISED Canada under ISED Canada Registration Number 3062D. Page 4 of 22

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B SYSTEM TEST CONFIGURATION Description of Test Configuration The EUT was configured for testing in an engineering mode which was provided by the manufacturer. The system employed GFSK modulation in 5.8GHz band, total 58 channels was used: Frequency Frequency Channel Channel (MHz) (MHz) 1 5729 30 5787 2 5731 31 5789 3 5733 32 5791 … … … … … … … … 24 5775 53 5833 25 5777 54 5835 26 5779 55 5837 27 5781 56 5839 28 5783 57 5841 29 5785 58 5843 Test was performed with Channel: 1, 24 and 58. Equipment Modifications No modification was made to the EUT tested. EUT Exercise Software The software “Certification_HG330.exe” was used for testing, which was provided by manufacturer. The maximum power with maximum duty cycle was configured as below setting. Test Software Certification_HG330.exe Version Test Frequency 5729MHz 5775MHz 5843MHz Power Level 22 22 22 Setting Support Equipment List and Details Manufacturer Description Model Serial Number SZ DJI Osmo Ronin-s RSFW / Technology Co.,Ltd. Page 5 of 22

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B Support Cable List and Details Shielding Length Cable Description Ferrite Core From Port To Type (m) S-Bus Cable Yes No 0.6 Ronin-s EUT Block Diagram of Test Setup EUT Ronin-s Non-Conductive Table 80/150cm above Ground Plane 1.5 Meter Page 6 of 22

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B SUMMARY OF TEST RESULTS Rules Description of Test Result FCC §15.407 (f) & §1.1310 & Maximum Permissable Exposure (MPE) Compliance §2.1091 Exemption Limits For Routine Evaluation-RF RSS-102 § 2.5.2 Compliance Exposure Evaluation FCC§15.203 Antenna Requirement Compliance RSS-GEN§8.3 FCC§15.207 (a) AC Line Conducted Emissions Not Applicable* RSS-Gen §8.8 FCC§15.205& §15.209 &§15.407(b) Undesirable Emission& Restricted Bands Compliance RSS-247§6.2 FCC§15.407(b) (1),(2),(3),(4) Out Of Band Emissions Compliance* RSS-247§6.2 FCC§15.407(a) RSS-247 §6.2 Emission Bandwidth Compliance* RSS-Gen§6.6 FCC§15.407(a) Conducted Transmitter Output Power Compliance* RSS-247 §6.2 FCC§15.407 (a) Power Spectral Density Compliance* RSS-247 §6.2 FCC§15.407(g) Frequency stability Compliance* Not Applicable*: The EUT was supplied by battery. Compliance*: RF module of this device is the same as the model: P1F1( FCC ID: 2ANDR-P1F11803, IC: 23060- P1F11803), the test results please refer to report NO. RDG180325002-00C. Page 7 of 22

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B FCC §15.407 (f) & §1.1310 & §2.1091- MAXIMUM PERMISSIBLE EXPOSURE (MPE) Applicable Standard According to subpart 15.407(f)and subpart §1.1310, systems operating under the provisions of this section shall be operated in a manner that ensures that the public is not exposed to radio frequency energy level in excess of the Commission’s guidelines. Limits for Maximum Permissible Exposure (MPE) (§1.1310, §2.1091) (B) Limits for General Population/Uncontrolled Exposure Frequency Range Electric Field Magnetic Field Power Density Averaging Time (MHz) Strength (V/m) Strength (A/m) (mW/cm2) (minutes) 0.3–1.34 614 1.63 *(100) 30 1.34–30 824/f 2.19/f *(180/f²) 30 30–300 27.5 0.073 0.2 30 300–1500 / / f/1500 30 1500–100,000 / / 1.0 30 f = frequency in MHz; * = Plane-wave equivalent power density; According to §1.1310 and §2.1091 RF exposure is calculated. Calculation formula: Prediction of power density at the distance of the applicable MPE limit S = PG/4R² = power density (in appropriate units, e.g. mW/cm2); P = power input to the antenna (in appropriate units, e.g., mW); G = power gain of the antenna in the direction of interest relative to an isotropic radiator, the power gain factor, is normally numeric gain; R = distance to the center of radiation of the antenna (appropriate units, e.g., cm); Calculated Data: Conducted output power Evaluation Power MPE Frequency Antenna Gain including Tune- Distance Density Limit (MHz) up Tolerance (cm) (mW/cm2) (mW/cm2) (dBi) (numeric) (dBm) (mW) 5729-5843 4.5 2.82 22.5 177.83 20.00 0.1 1.0 Note: 2.4GHz and 5.8GHz can`t transmit simultaneously Result: The device meet FCC MPE at 20 cm distance Page 8 of 22

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B RSS-102 § 2.5.2 - EXEMPTION LIMITS FOR ROUTINE EVALUATION – RF EXPOSURE EVALUATION Applicable Standard According to RSS-102 § (2.5.2): RF exposure evaluation is required if the separation distance between the user and/or bystander and the device’s radiating element is greater than 20 cm, except when the device operates as follows: • below 20 MHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 1 W (adjusted for tune-up tolerance); • at or above 20 MHz and below 48 MHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 4.49/ƒ0.5 W (adjusted for tune-up tolerance), where ƒ is in MHz; • at or above 48 MHz and below 300 MHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 0.6 W (adjusted for tune-up tolerance); • at or above 300 MHz and below 6 GHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 1.31 x 10-2 ƒ0.6834 W (adjusted for tune-up tolerance), where ƒ is in MHz; • at or above 6 GHz and the source-based, time-averaged maximum e.i.r.p. of the device is equal to or less than 5 W (adjusted for tune-up tolerance). In these cases, the information contained in the RF exposure technical brief may be limited to information that demonstrates how the e.i.r.p. was derived. Calculated Data: The maximum power including tune-up tolerance is 22.5dBm@ 5.8GHz band, the maximum antenna gain is 4.5 dBi, so the maximum e.r.i.p. is 27.0 dBm (0.50W) Exemption from Routine Evaluation Limit is: 1.31 x 10-2 ƒ0.6834 = 1.31 x 10-2 x 57290.6834 = 4.85 > 0.50W So the device is compliance exemption from Routine Evaluation Limits –RF exposure Evaluation. Result: Compliance Page 9 of 22

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B FCC §15.203 ,RSS-GEN§8.3- ANTENNA REQUIREMENT Applicable Standard According to § 15.203, an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device. The use of a permanently attached antenna or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply with the provisions of this section. The manufacturer may design the unit so that a broken antenna can be replaced by the user, but the user of a standard antenna jack or electrical connector is prohibited. The structure and application of the EUT were analyzed to determine compliance with section §15.203 of the rules. §15.203 state that the subject device must meet the following criteria: a. Antenna must be permanently attached to the unit. b. Antenna must use a unique type of connector to attach to the EUT. Unit must be professionally installed, and installer shall be responsible for verifying that the correct antenna is employed with the unit. According to RSS-Gen §8.3, The applicant for equipment certification, as per RSP-100, must provide a list of all antenna types that may be used with the licence-exempt transmitter, indicating the maximum permissible antenna gain (in dBi) and the required impedance for each antenna. Licence-exempt transmitters that have received equipment certification may operate with different types of antennas. However, it is not permissible to exceed the maximum equivalent isotropically radiated power (e.i.r.p.) limits specified in the applicable standard (RSS) for the licence-exempt apparatus. Testing shall be performed using the highest gain antenna of each combination of licence-exempt transmitter and antenna type, with the transmitter output power set at the maximum level.9 When a measurement at the antenna connector is used to determine RF output power, the effective gain of the device’s antenna shall be stated, based on a measurement or on data from the antenna manufacturer. User manuals for transmitters equipped with detachable antennas shall also contain the following notice in a conspicuous location: This radio transmitter (identify the device by certification number or model number if Category II) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Immediately following the above notice, the manufacturer shall provide a list of all antenna types approved for use with the transmitter, indicating the maximum permissible antenna gain (in dBi). Antenna Connector Construction The EUT has a external antenna arrangement permanently attached to the unit, the antenna gain is 2.18 dBi in 2.4GHz band and 4.5 dBi in 5.8GHz band, fulfill the requirement of this section. Please refer to the EUT photos. Result: Compliance. Page 10 of 22

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B FCC §15.209, §15.205 , §15.407(b) &RSS-247 §6.2, RSS-GEN§8.10– UNWANTED EMISSION Applicable Standard According to FCC §15.407; §15.209; §15.205; (b) Undesirable emission limits. Except as shown in paragraph (b)(7) of this section, the maximum emissions outside of the frequency bands of operation shall be attenuated in accordance with the following limits: (1) For transmitters operating in the 5.15-5.25 GHz band: All emissions outside of the 5.15-5.35 GHz band shall not exceed an e.i.r.p. of −27 dBm/MHz. (2) For transmitters operating in the 5.25-5.35 GHz band: All emissions outside of the 5.15-5.35 GHz band shall not exceed an e.i.r.p. of −27 dBm/MHz. (3) For transmitters operating in the 5.47-5.725 GHz band: All emissions outside of the 5.47-5.725 GHz band shall not exceed an e.i.r.p. of −27 dBm/MHz. (4) For transmitters operating in the 5.725-5.85 GHz band: (i) All emissions shall be limited to a level of −27 dBm/MHz at 75 MHz or more above or below the band edge increasing linearly to 10 dBm/MHz at 25 MHz above or below the band edge, and from 25 MHz above or below the band edge increasing linearly to a level of 15.6 dBm/MHz at 5 MHz above or below the band edge, and from 5 MHz above or below the band edge increasing linearly to a level of 27 dBm/MHz at the band edge. (ii) Devices certified before March 2, 2017 with antenna gain greater than 10 dBi may demonstrate compliance with the emission limits in §15.247(d), but manufacturing, marketing and importing of devices certified under this alternative must cease by March 2, 2018. Devices certified before March 2, 2018 with antenna gain of 10 dBi or less may demonstrate compliance with the emission limits in §15.247(d), but manufacturing, marketing and importing of devices certified under this alternative must cease before March 2, 2020. (5) The emission measurements shall be performed using a minimum resolution bandwidth of 1 MHz. A lower resolution bandwidth may be employed near the band edge, when necessary, provided the measured energy is integrated to show the total power over 1 MHz. (6) Unwanted emissions below 1 GHz must comply with the general field strength limits set forth in §15.209. Further, any U-NII devices using an AC power line are required to comply also with the conducted limits set forth in §15.207. (7) The provisions of §15.205 apply to intentional radiators operating under this section. (8) When measuring the emission limits, the nominal carrier frequency shall be adjusted as close to the upper and lower frequency band edges as the design of the equipment permits. Page 11 of 22

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B According to RSS-247§6.2 Frequency band 5150-5250 MHz Frequency band 5250-5350 MHz Frequency bands 5470-5600 MHz and 5650-5725 MHz: Page 12 of 22

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B Frequency band 5725-5850 MHz EUT Setup Below 1 GHz: Page 13 of 22

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B 1-26.5 GHz: 26.5-40 GHz: The radiated emission tests were performed in the 3 meters chamber test site, using the setup accordance with the ANSI C63.10-2013. The specification used was the FCC 15.209, FCC 15.407 and RSS-247, RSS-Gen limits. The external I/O cables were draped along the test table and formed a bundle 30 to 40 cm long in the middle. The spacing between the peripherals was 10 cm. EMI Test Receiver & Spectrum Analyzer Setup The system was investigated from 30 MHz to 40 GHz. During the radiated emission test, the EMI test receiver & Spectrum Analyzer Setup were set with the following configurations: 30-1000MHz: Measurement RBW Video B/W IF B/W QP 120 kHz 300 kHz 120kHz Page 14 of 22

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B 1GHz- 40GHz: Measurement Duty cycle RBW Video B/W PK Any 1MHz 3 MHz >98% 1MHz 10 Hz Ave. <98% 1MHz 1/T Test Procedure Maximizing procedure was performed on the highest emissions to ensure that the EUT complied with all installation combinations. Data was recorded in Quasi-peak detection mode for frequency range of 30 MHz-1GHz, peak and Average detection modes for frequencies above 1GHz. According to KDB 789033 D02 General UNII Test Procedures New Rules v02r01, emission shall be computed as: E [dBμV/m] = EIRP[dBm] + 95.2, for d = 3 meters. According to C63.10, the above 1G test result shall be extrapolated to the specified distance using an extrapolation factor of 20dB/decade from 3m to 1.5m or 1m Distance extrapolation factor =20 log (specific distance [3m]/test distance [1.5m]) dB= 6.02 dB or Distance extrapolation factor =20 log (specific distance [3m]/test distance [1m]) dB= 9.54 dB All emissions under the average limit and under the noise floor have not recorded in the report. Corrected Amplitude & Margin Calculation For the range 30MHz-1GHz, the Corrected Amplitude is calculated by adding the Antenna Factor and Cable Loss, and subtracting the Amplifier Gain from the Meter Reading. The basic equation is as follows: Corrected Amplitude = Meter Reading + Antenna Factor + Cable Loss - Amplifier Gain The “Margin” column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of 7dB means the emission is 7dB below the limit. The equation for margin calculation is as follows: Margin = Limit - Corrected Amplitude For the range 1GHz-40GHz, Test performed at 1.5m, the Corrected Amplitude is calculated by adding the Antenna Factor and Cable Loss, and subtracting the Amplifier Gain from the Meter Reading and the Distance extrapolation factor. The basic equation is as follows: Extrapolation result = Meter Reading + Antenna Factor + Cable Loss - Amplifier Gain-Distance extrapolation factor The “Margin” column of the following data tables indicates the degree of compliance with the applicable limit. For example, a margin of 7dB means the emission is 7dB below the limit. The equation for margin calculation is as follows: Margin = Limit-Extrapolation result Page 15 of 22

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B Test Equipment List and Details Serial Calibration Calibration Manufacturer Description Model Number Date Due Date Sunol Sciences Antenna JB3 A060611-1 2017-11-10 2020-11-10 R&S EMI Test Receiver ESCI 100224 2017-12-11 2018-12-11 HP Amplifier 8447D 2727A05902 2017-09-05 2018-09-05 N/A Coaxial Cable 4m C-0400-01 2017-09-05 2018-09-05 N/A Coaxial Cable 0.75m C-0075-01 2017-09-05 2018-09-05 N/A Coaxial Cable 10m C-1000-01 2017-09-05 2018-09-05 Agilent Spectrum Analyzer E4440A SG43360054 2018-01-04 2019-01-04 ETS-Lindgren Horn Antenna 3115 000 527 35 2016-01-05 2019-01-05 AFS42-00101800- MITEQ Amplifier 2001271 2017-09-05 2018-09-05 25-S-42 Ducommun 1007726-02 Horn Antenna ARH-4223-02 2017-06-16 2020-06-15 Technolagies 1304 Ducommun 1007726-01 Horn Antenna ARH-2823-02 2016-11-18 2019-11-18 Technolagies 1302 Quinstar Amplifier QLW-18405536-JO 15964001001 2017-06-27 2018-06-27 unknown Coaxial Cable 8m C0800/01 2017-09-05 2018-09-05 R&S Spectrum Analyzer FSP 38 100478 2017-12-08 2018-12-08 Chengdu OuLi Bandrejector Filter 5725-5850 005 2017-09-05 2018-09-05 Farad Test Software EZ-EMC V1.1.4.2 N/A N/A * Statement of Traceability: Bay Area Compliance Laboratories Corp. (Dongguan) attests that all calibrations have been performed, traceable to National Primary Standards and International System of Units (SI). Test Data Environmental Conditions Temperature: 25 ~ 25.1 C Relative Humidity: 49 ~ 50 % ATM Pressure: 100.9 ~101 kPa The testing was performed by Vern Shen & Harry Yang on 2018-05-13 & 2018-05-14. Test Mode: Transmitting Page 16 of 22

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B 1) 30MHz-1GHz(Middle channel was the worst): Horizontal: Receiver Correction Cord. Frequency Limit Margin Reading Detector Factor Amp. (MHz) (dBμV/m) (dB) (dBμV) (dB/m) (dBμV/m) 30.9700 25.79 QP 0.81 26.60 40.00 13.40 57.1600 40.45 QP -12.35 28.10 40.00 11.90 103.7200 38.01 QP -7.91 30.10 43.50 13.40 156.1000 41.24 QP -5.94 35.30 43.50 8.20 252.1300 42.95 QP -6.15 36.80 46.00 9.20 366.5900 36.57 QP -2.77 33.80 46.00 12.20 Page 17 of 22

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B Vertical: Receiver Correction Cord. Frequency Limit Margin Reading Detector Factor Amp. (MHz) (dBμV/m) (dB) (dBμV) (dB/m) (dBμV/m) 30.0000 20.66 QP 1.54 22.20 40.00 17.80 57.1600 36.55 QP -12.35 24.20 40.00 15.80 86.2600 37.22 QP -11.52 25.70 40.00 14.30 101.7800 34.61 QP -8.41 26.20 43.50 17.30 156.1000 34.44 QP -5.94 28.50 43.50 15.00 367.5600 34.67 QP -2.77 31.90 46.00 14.10 Page 18 of 22

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B 2) 1-40GHz: Receiver Rx Antenna Cable Amplifier Corrected Extrapolation Frequency Limit Margin Reading Polar Factor loss Gain Amplitude result (MHz) Detector (dBμV/m) (dB) (dBμV) (H/V) (dB/m) (dB) (dB) (dBμV/m) (dBμV/m) Low Channel: 5729 MHz 5729.00 78.13 PK H 34.19 3.69 0.00 116.01 109.99 N/A N/A 5729.00 76.64 AV H 34.19 3.69 0.00 114.52 108.5 N/A N/A 5729.00 91.25 PK V 34.19 3.69 0.00 129.13 123.11 N/A N/A 5729.00 89.81 AV V 34.19 3.69 0.00 127.69 121.67 N/A N/A 5725.00 57.81 PK V 34.19 3.69 0.00 95.69 89.67 122.20 32.53 5720.00 42.36 PK V 34.19 3.69 0.00 80.24 74.22 110.80 36.58 5700.00 28.44 PK V 34.18 3.68 0.00 66.30 60.28 105.20 44.92 5650.00 25.43 PK V 34.16 3.63 0.00 63.22 57.2 68.20 11.00 11458.00 56.14 PK V 38.96 6.59 37.33 64.36 58.34 74.00 15.66 11458.00 50.45 AV V 38.96 6.59 37.33 58.67 52.65 54.00 1.35 17187.00 50.66 PK V 41.28 8.77 38.64 62.07 56.05 74.00 17.95 17187.00 44.38 AV V 41.28 8.77 38.64 55.79 49.77 54.00 4.23 Middle Channel: 5775 MHz 5775.00 75.76 PK H 34.21 3.70 0.00 113.67 107.65 N/A N/A 5775.00 74.11 AV H 34.21 3.70 0.00 112.02 106 N/A N/A 5775.00 89.62 PK V 34.21 3.70 0.00 127.53 121.51 N/A N/A 5775.00 88.17 AV V 34.21 3.70 0.00 126.08 120.06 N/A N/A 11550.00 54.83 PK V 39.00 6.61 37.42 63.02 57 74.00 17.00 11550.00 47.85 AV V 39.00 6.61 37.42 56.04 50.02 54.00 3.98 17325.00 50.65 PK V 42.09 8.80 38.54 63.00 56.98 74.00 17.02 17325.00 44.68 AV V 42.09 8.80 38.54 57.03 51.01 54.00 2.99 High Channel: 5843 MHz 5843.00 74.33 PK H 34.24 3.74 0.00 112.31 106.29 N/A N/A 5843.00 72.91 AV H 34.24 3.74 0.00 110.89 104.87 N/A N/A 5843.00 88.96 PK V 34.24 3.74 0.00 126.94 120.92 N/A N/A 5843.00 87.36 AV V 34.24 3.74 0.00 125.34 119.32 N/A N/A 5850.00 43.90 PK V 34.24 3.75 0.00 81.89 75.87 122.20 46.33 5855.00 35.18 PK V 34.24 3.75 0.00 73.17 67.15 110.80 43.65 5875.00 26.48 PK V 34.25 3.77 0.00 64.50 58.48 105.20 46.72 5925.00 24.73 PK V 34.27 3.80 0.00 62.80 56.78 68.20 11.42 11686.00 57.63 PK V 39.00 6.65 37.57 65.71 59.69 74.00 14.31 11686.00 50.75 AV V 39.00 6.65 37.57 58.83 52.81 54.00 1.19 17529.00 51.33 PK V 43.28 8.85 38.39 65.07 59.05 74.00 14.95 17529.00 44.95 AV V 43.28 8.85 38.39 58.69 52.67 54.00 1.33 Page 19 of 22

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B Worst plots(Middle channel) Horizontal Page 20 of 22

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B Vertical Page 21 of 22

Bay Area Compliance Laboratories Corp. (Dongguan) Report No.: RDG180507002-00B ***** END OF REPORT ***** Page 22 of 22


Document Created: 2018-05-29 09:14:40
Document Modified: 2018-05-29 09:14:40
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC