User Manual

FCC ID: 2ANDL-WR6

Users Manual

Download: PDF
FCCID_4260095

WR6 Datasheet Tuya Smart Wi-Fi Module 1 Product Overview WR6 is a low power-consuming built-in Wi-Fi module developed by Hangzhou Tuya Inc. It consists of a highly integrated RF microchip (W302 12E77H2) and an external flash chip, with a built-in Wi-Fi network protocol stack and robust library functions. WR6 also contains a low power- consuming ARM CM4F, a WLAN MAC, a 1T1R WLAN, and the maximum basic frequency of 125 MHz, and is embedded with a 256 KB SRAM, a 2 MB flash, and rich peripheral resources. WR6 is an RTOS platform that integrates all the function libraries of the Wi-Fi MAC and TCP/IP protocols. You can develop built-in Wi-Fi products as required. 1.1 Features ² Built-in low power-consuming 32-bit CPU functioning as an application processor ² Working voltage: 4.5 V to 5.5 V ² Peripherals: nine GPIOs, one UART, and one ADC ² Wi-Fi connectivity l 802.11b/g/n20/n40 l Channels 1 to 11@ 2.4 GHz l WPA/WPA2 security mode l Smart network configuration function (forAndroid and iOS devices) l Onboard PCB antenna l Working temperature: –20°C to +85°C Tuya Inc. Version 1.0.2

WR6 Datasheet 1.2 Applications ² Intelligent building ² Smart home and household appliances ² Healthcare ² Industrial wireless control ²Baby monitor ² Network camera ² Intelligent bus Tuya Inc. Version 1.0.2

WR6 Datasheet 2 Module Interfaces 2.1 Dimensions and Footprint WR6 has two rows of pins (2 x 7) with a 2 mm pin pitch. Dimensions (H x W x D) of WR6 are as follows: 4.8 mm x 37.8 mm x 21.7 mm. Figure 2-1 shows the dimensions of WR6. 2.2 Pin Definition Table 2-1 describes common pins. Table 2-1 WR6 interface pins No. Symbol I/O Type Function 1 A_14 I/O GPIOA_14 2 A_15 I/O GPIOA_15 3 EN I/O External enabled reset pin (active at low level) No. Symbol I/O Type Function 4 A_0 I/O GPIOA_0, which cannot be pulled up during power-on and can be configured after power-on 5 A_12 I/O GPIOA_12 6 ADC AI ADC port, with the maximum output power of 5 V 7 A_5 I/O GPIOA_5 8 3.3 V P Module power supply pin (3.3 V) 9 GND P Power supply reference ground pin 10 A_19 I/O GPIOA_19 11 A_22 I/O GPIOA_22 12 Log_TX I/O UART_Log_TXD (used for printing the module internal information) 13 Log_RX I/O UART_Log_RXD (used for printing the module internal information) 14 GND P Power supply reference ground pin 15 VIN P External power input (5 V) 16 GND P Power supply reference ground pin 17 RXD1 I/O UART0_RXD (user serial port) 18 TXD1 I/O UART0_TXD (user serial port) Note: P indicates power-supply pins, I/O indicates input/output pins, and AI indicates analog input pins. Tuya Inc. Version 1.0.2

WR6 Datasheet 3 Electrical Parameters 3.1 Absolute Electrical Parameters Table 3-1 Absolute electrical parameters Parameter Description Minimum Maximum Unit Value Value Ts Storage temperature –40 +125 °C VIN Power supply voltage –0.3 +5.5 V Static electricity voltage TAMB – 25°C N/A 2 kV (human body model) Static electricity voltage TAMB – 25°C N/A 0.5 kV (machine model) 3.2 Electrical Conditions Table 3-2 Normal electrical conditions Parameter Description Minimum Typical Maximum Unit Value Value Value Ta Working temperature –20 25 +85 °C VIN Working voltage 4.5 5.0 5.5 V VIL I/O low-level input –0.3 N/A +0.8 V VIH I/O high-level input 2.47 N/A 3.6 V VOL I/O low-level output N/A N/A 0.34 V VOH I/O high-level output 2.64 N/A 3.4 V Imax I/O drive current N/A N/A 16 mA Cpad Input pin capacitance N/A 2 N/A pF Tuya Inc. Version 1.0.2

WR6 Datasheet 3.3 Wi-Fi TX Power Consumption Table 3-3 TX power consumption during constant emission Symbol Mode Power Typical Value Unit IRF 802.11b 20.15dBm 287 mA IRF 802.11g 22.30dBm 255 mA IRF 802.11n BW20 21.30dBm 244 mA IRF 802.11n BW40 20.70dBm 220 mA 3.4 Wi-Fi RX Power Consumption Table 3-4 RX power consumption during constant receiving Symbol Mode Typical Value Unit IRF CPU sleep 90 mA IRF CPU active 120 mA 3.5 Working Power Consumption Table 3-5 WR6 operating current Working Working Status (Ta = 25°C) Typical Peak Unit Mode Value Value* EZ mode The module is in EZ mode, and the Wi-Fi 115 125 mA indicator quickly flashes. Idle The module is connected to the network, and 60 209 mA the Wi-Fi indicator is steady on. Connection The module is connected to the network, and 118 198 mA mode the Wi-Fi indicator is steady on. Disconnection The module is disconnected from the network, 34 192 mA mode and the Wi-Fi indicator is steady off. Note: The peak duration is about 5 µs. The preceding parameter values vary depending on the firmware functions. Tuya Inc. Version 1.0.2

WR6 Datasheet 4 RF Features 4.1 Basic RF Features Table 4-1 Basic RF features Parameter Description Frequency range 2.412 GHz to 2.462 GHz Wi-Fi standard IEEE 802.11b/g/n20/n40 (channels 1 to 11) 802.11b: 1, 2, 5.5, or 11 (Mbit/s) 802.11g: 6, 9, 12, 18, 24, 36, 48, or 54 (Mbit/s) Data transmission rate 802.11n: HT20 MCS0 to MCS7 802.11n: HT40 MCS0 to MCS7 Antenna type PCB antenna (default) 4.2Wi-Fi RX Sensitivity Table 4-2 RX sensitivity Parameter Minimum Typical Maximum Unit Value Value Value PER < 8%, 802.11b CCK 11 Mbit/s N/A –91 N/A dBm mode PER < 10%, 802.11g 54 Mbit/s N/A –75 N/A dBm OFDM mode PER < 10%, 802.11n MCS7 N/A –72 N/A dBm OFDM mode Tuya Inc. Version 1.0.2

WR6 Datasheet 5 Antenna Information 5.1 Antenna Types onboard PCB antenna 5.2 Antenna Interference Reduction To ensure optimal Wi-Fi performance when the module uses an onboard PCB antenna, it is recommended that the antenna be at least 15 mm away from other metal parts. The following figures show five common antenna routing solutions. Solutions 1 and 2 have the best test performance, and the RF performance is the same as that of a single module. If the antenna must be routed on the PCB due to restrictions, solution 3 is recommended. However, the RF performance may be attenuated by 1 to 2 dBm. Solution 5 has the poorest RF performance and is not recommended. In solution 5, the antenna is routed in the PCB frame and RF signals cannot be transmitted or received properly. Tuya Inc. Version 1.0.2

WR6 Datasheet PCB antenna PCB antenna Solution 1: Antenna routed outside the PCB Solution 2: Antenna routed along the frame frame edge with carved area below PCB antenna PCB antenna Solution 3: Antenna routed along the frame Solution 4: Antenna routed in the frame with edge without copper below carved area below PCB antenna Solution 5: Antenna routed in the frame with copper or wires below Tuya Inc. Version 1.0.2

WR6 Datasheet 6 Packaging Information and Production Instructions 6.1 Production Instructions Storage conditions of a delivered module are as follows: 1. The anti-moisture bag must be placed in an environment where the temperature is below 30°C and the relative humidity is lower than 85%. 2. The shelf life of a dry-packaged product is six months from the date when the product is packaged and sealed. Precautions: 1. Throughout the production process, each involved operator must wear an ESD wrist strap. 2. During the operation, strictly protect the module from water and strains. 6.2 Recommended Oven Temperature Curve Tuya Inc. Version 1.0.2

WR6 Datasheet Regulatory Module Integration Instructions This device complies with part 15.247 of the FCC Rules. The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The antenna is PCB Antenna and maximum gain is 2.5dBi . This module has been granted modular approval for mobile applications. OEM integrators for host products may use the module in their final products without additional FCC certification if they meet the following conditions. Otherwise, additional FCC approvals must be obtained. The host product with the module installed must be evaluated for simultaneous transmission requirements. The user’s manual for the host product must clearly indicate the operating requirements and conditions that must be observed to ensure compliance with current FCC RF exposure guidelines. To comply with FCC regulations limiting both maximum RF output power and human exposure to RF radiation, use this module only with the included onboard antenna. The final host / module combination may also need to be evaluated against the FCC Part 15B criteria for unintentional radiators in order to be properly authorized for operation as a Part 15 digital device. FC Statement FCC Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. FCC Label Instructions: The outside of final products that contains this module device must display a label referring to the enclosed module. This exterior label can use wording such as: “Contains Transmitter Module FCC ID: 2ANDL-WR6 ”,or “Contains FCC ID: 2ANDL-WR6 ”, Any similar wording that expresses the same meaning may be used. Tuya Inc. Version 1.0.2


Document Created: 2019-04-30 22:02:49
Document Modified: 2019-04-30 22:02:49
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC