Users Manual

FCC ID: 2ANDL-WR1E

Users Manual

Download: PDF

FCCID_4313946

WR1E User Manual

2. Dimensions and Footprint

2.1Dimensions

WR1E has 2 columns of Pins (2*9).The distance between each Pin is1.5 mm.
Size of WR1E: 18 mm (W)×23.5 mm (L) ×3.3 mm (H)

2.2 Pin Definition

Table 1 shows the general pin attributes of WR1E
Table 1. The typical pin definition of WR1E
PIN NAME TYP DISCREPTION
NO. E
1 VCC P UART0_TXDThe power conversion（5V or 3.3V）
2 UART0_TXD I/O UART0_TXD
3 UART0_RX I/O UART0_RXD
D
4 VD33 P （3.3V）
5 GND P Power supply
6 GPIOA_14 I/O GPIOA_14
7 GPIOA_15 I/O GPIOA_15
8 LOG_TXD I/O UART_Log_TXD
9 GPIOA_12 I/O GPIOA_12
10 GPIOA_5 I/O GPIOA_5
11 LOG_RXD I/O UART_Log_RXD
12 GPIOA_19 I/O GPIOA_19
13 GPIOA_22 I/O GPIOA_22
14 GND P Power supply
15 GND P Power supply
16 CHIP_EN I/O
17 ADC AI ADC，max 5V
18 GND P Power supply

Note: S: Power supply pins; I/O: Digital input or output pins; AI: Analog input.

WR1E User Manual

3. Electrical Characteristics

3.1 Absolute Maximum Ratings

Table 3.1. Absolute Maximum Ratings
PARAMETERS DESCRIPTION MIN MAX UNIT
Ts Storage temperature ‐40 105 ℃
VCC Supply voltage ‐0.3 3.6 V
Static electricity voltage TAMB‐25℃ ‐ 2 KV
(human model)
Static electricity voltage TAMB‐25℃ ‐ 0.5 KV
(machine model)

3.2 Electrical Conditions

Table 3.2. Electrical Conditions
PARAMETERS DESCRIPTION MIN TYPICAL MAX UNIT
Ta Working temperature ‐20 ‐ 85 ℃
VCC Working voltage 3 ‐ 3.6 V
VIL IO low level input ‐0.3 ‐ VDD*0.25 V
VIH IO high level input VDD*0.75 ‐ VDD V
VOL IO low level output ‐ ‐ VDD*0.1 V
VoH IO high level output VDD*0.8 ‐ V V
Imax IO drive current ‐ ‐ 16 mA
Cpad Input capacitor ‐ 2 ‐ pF

WR1E User Manual

3.3 Wi-Fi Receiving CurrentConsumptions

Table 3.3. Wi-Fi RX currentconsumption
PARAMETERS MODE TYPICAL UNIT
IRF CPU sleep 90 mA
IRF CPU active 120 mA

3.4 Working Mode CurrentConsumptions

Table 3.4. The module working currentconsumption
WORK MODE AT TA=25℃ TYPICAL MAX* UNIT

EZ Mode WR1E is under EZ paring mode, Wi‐Fi indicator 115 125 mA
light flashes quickly
Standby Mode WR1E is connected, Wi‐Fi indicator light is on 60 209 mA

Operation Mode WR1E is connected, Wi‐Fi indicator light is on 118 198 mA
Disconnection WR1E is disconnected, Wi‐Fi indicator light is 34 192 mA
Mode off
Note: peak continuous time is about 5us.
The parameter shown above will vary dependingon different firmware functions.

4. WLAN Radio Specification

4.1 Basic Radio Frequency Characteristics

Table 41.Basic Radio frequency characteristics
PARAMETERS DESCRIPTION
Frequency band 2412MHz-2462MHz
Wi‐Fi standard IEEE 802.11n/g/b (Terminal 1‐11)
Data transmitting rate 11b:1,2,5.5,11(Mbps)
11g:6,9,12,18,24,36,48,54(Mbps)
11n:HT20,MCS0~7
11n:HT40,MCS0~7
Antenna type PCB antenna (default)
U.FL RF connector external antenna

WR1E User Manual

4.2Wi-Fi TransmittingPower
Table 4.2. Wi-Fi transmitting power

RF output power

802.11b:20.72dBm
802.11g:24.98dBm
802.11n20:23.82dBm
802.11n40:22.03dBm

4.3Wi-Fi Receiving Sensitivity

Table 4.3. Wi-Fi Receiving sensitivity
PARAMETERS MIN TYPICAL MAX UNI
T
PER<8%, Receiving sensitivity, 802.11b CCK Mode 11M ‐ ‐91 ‐ dBm
PER<10%, Receiving sensitivity, 802.11g OFDM Mode 54M ‐ ‐75 ‐ dBm
PER<10%, Receiving sensitivity, 802.11n OFDM Mode MCS7 ‐ ‐72 ‐ dBm

WR1E User Manual

Regulatory Module Integration Instructions

2.2 List of applicable FCC rules

This device complies with part 15.247 of the FCC Rules.

2.3 Summarize the specific operational use conditions

This module can be used in household electrical appliances as well as lighting equipments.

The input voltage to the module should be nominally 3.0 to 3.6VDC ,typical value

3.3VDC and the ambient temperature of the module should not exceed 85℃.

TOn-board PCB antenna, and IPEX connector for external antenna with 2.5dBi gain.Other antenna

arrangement is not covered by this certification.

The antenna is not field replaceable. If the antenna needs to be changed, the certification

should be re-applied.

2.4 Limited module procedures

Not applicable

2.5 Trace antenna designs

Not applicable

2.6 RF exposure considerations

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment .This equipment should be installed and operated with minimum distance

20cm between the radiator& your body. If the device built into a host as a portable usage,

the additional RF exposure evaluation may be required as specified by§ 2.1093.

WR1E User Manual

2.7 Antennas

The module have a PCB antenna or IPEX connector for external antenna.

2.8 Label and compliance information

The outside of final products that contains this module device must display a label

referring to the enclosed module. This exterior label can use wording such as: “Contains

Transmitter Module FCC ID: 2ANDL-WR1E ”,or “Contains FCC ID: 2ANDL-WR1E ”, Any

similar wording that expresses the same meaning may be used.

2.9 Information on test modes and additional testing requirements

a) The modular transmitter has been fully tested by the module grantee on the required

number of channels, modulation types, and modes, it should not be necessary for the

host installer to re-test all the available transmitter modes or settings. It is

recommended that the host product manufacturer, installing the modular transmitter,

perform some investigative measurements to confirm that the resulting composite

system does not exceed the spurious emissions limits or band edge limits (e.g., where a

different antenna may be causing additional emissions).

b) The testing should check for emissions that may occur due to the intermixing of

emissions with the other transmitters, digital circuitry, or due to physical properties of

the host product (enclosure). This investigation is especially important when integrating

multiple modular transmitters where the certification is based on testing each of them in

a stand-alone configuration. It is important to note that host product manufacturers

should not assume that because the modular transmitter is certified that they do not

WR1E User Manual

have any responsibility for final product compliance.

c) If the investigation indicates a compliance concern the host product manufacturer is

obligated to mitigate the issue. Host products using a modular transmitter are subject to

all the applicable individual technical rules as well as to the general conditions of

operation in Sections 15.5, 15.15, and 15.29 to not cause interference. The operator of

the host product will be obligated to stop operating the device until the interference has

been corrected

Below are steps for TX verification：

wpriv mp_start //enter MP mode

iwpriv mp_channel 1 //set channel to 1 . 2, 3, 4~11 etc.

iwpriv mp_bandwidth 40M=0,shortGI=0 //40M=0 set 20M mode and long GI，

40M=1 set 40M mode

iwpriv mp_ant_tx a //select antenna A for operation

iwpriv mp_txpower patha=44,pathb=44 //set path A and path B Tx power level

iwpriv mp_rate 108 //set OFDM data rate to 54Mbps,ex:

CCK 1M = 2, CCK 5.5M = 11, KK, OFDM54M = 108 N Mode: MCS0 = 128, MCS1

= 129…..etc.

iwpriv mp_ctx background,pkt //start packet continuous Tx

iwpriv mp_ctx stop //stop continuous Tx

2.10 Additional testing, Part 15 subpart B disclaimer

The final host / module combination need to be evaluated against the FCC Part 15B

criteria for unintentional radiators in order to be properly authorized for operation as a Part

15 digital device.

WR1E User Manual

The host integrator installing this module into their product must ensure that the final

composite product complies with the FCC requirements by a technical assessment or

evaluation to the FCC rules, including the transmitter operation and should refer to

guidance in KDB 996369.

Frequency spectrum to be investigated

For host products with certified modular transmitter, the frequency range of investigation

of the composite system is specified by rule in Sections 15.33(a)(1) through (a)(3), or the

range applicable to the digital device, as shown in Section 15.33(b)(1), whichever is the

higher frequency range of investigation.

Operating the host product

When testing the host product, all the transmitters must be operating.The transmitters can

be enabled by using publicly-available drivers and turned on, so the transmitters are

active. In certain conditions it might be appropriate to use a technology-specific call box

(test set) where accessory devices or drivers are not available.

When testing for emissions from the unintentional radiator, the transmitter shall be placed

in the receive mode or idle mode, if possible. If receive mode only is not possible then, the

radio shall be passive (preferred) and/or active scanning. In these cases, this would need

to enable activity on the communication BUS (i.e., PCIe, SDIO, USB) to ensure the

unintentional radiator circuitry is enabled. Testing laboratories may need to add

attenuation or filters depending on the signal strength of any active beacons (if applicable)

from the enabled radio(s). See ANSI C63.4, ANSI C63.10 and ANSI C63.26 for further

WR1E User Manual

general testing details.

The product under test is set into a link/association with a partnering WLAN device, as per

the normal intended use of the product. To ease testing, the product under test is set to

transmit at a high duty cycle, such as by sending a file or streaming some media content.

FCC Statement

Any Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment. This device complies

with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause undesired operation

Document Created: 2019-06-11 23:35:54
Document Modified: 2019-06-11 23:35:54

© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC