User Manual

FCC ID: 2ANDL-TYAUXJ

Users Manual

Download: PDF
FCCID_4192647

DATASHEET TuyaSmartWi-Fi Module 1. Product Overview TYAUX_J is a low power consumption module with built-in Wi-Fi connectivity solution designed by Hangzhou Tuya Information Technology Co., Ltd. for serial communication between 12V level and 3.3V level. The Wi-Fi Module consists of a highly integrated wireless radio chip W302 I119UP1 and some extra flash that has been programed with Wi-Fi network protocol and plenty of software examples. TYAUX_J in clude a ARM CM4F, WLAN MAC, 1T1R WLAN, maximum frequency reaches 125MHz, 256K SRAM, 2M byte flash and various peripheral resources. TYAUX_J is a RTOS platform, embedded with all the Wi-Fi MAC and TCP/IP protocol function examples, users can customize their Wi-Fi product by using these software examples. 1.1 Features  Integrated low power consumption 32-bit CPU, also known as application processor  Basic frequency of the CPU can support 125 MHz  Supply voltage range: 12V  Peripherals: 1 UART  Wi-Fi connectivity:  802.11 B/G/N20/N40  Channel 1 to 11 @ 2.4GHz  Support WPA/WPA2  Support Smart Config function for both Android and IOS devices  Pass CE, FCC, SRRC certifications  Operating temperature range: -20℃ to 85℃ 1.2 Main ApplicationFields  Intelligent Building  Intelligent home, Intelligent household applications  Healthy devices  Industrial wireless control  Baby monitor  Webcam  Intelligent bus

DATASHEET 2. Dimensions and Footprint 2.1Dimensions TYAUX_J has 2 columns of Pins (2*7).The distance between each Pin is 2 mm. Size of TYAUX_J: 19.5mm(W)*35.5mm(L)*3.5mm(H) Figure 2.1 shows the dimensions of TYAUX_J. Figure 2.1. The dimensions of TYAUX_J 2.2 Pin Definition Table 1 shows the general pin attributes of TYAUX_J Table 1. The typical pin definition of TYAUX_J

DATASHEET PIN NAME TYPE DISCREPTION NO. 1 GND P Ground 4 TX I/O UART0_TXD 5 RX I/O UART0_RXD 12 VIN P Module 12V power input pin Note: P: Power supply pins; I/O: Digital input or output pins;

DATASHEET 3. Electrical Characteristics 3.1 Absolute Maximum Ratings Table 3.1. Absolute Maximum Ratings PARAMETERS DESCRIPTION MIN MAX UNIT Ts Storage temperature -40 125 ℃ VCC Supply voltage -0.3 18 V Static electricity voltage TAMB-25℃ - 2 KV (human model) Static electricity voltage TAMB-25℃ - 0.5 KV (machine model) 3.2 Electrical Conditions Table 3.2. Electrical Conditions PARAMETERS DESCRIPTION MIN TYPICAL MAX UNIT Ta Working temperature -20 - 85 ℃ VIN Working voltage 4.5 - 18 V VIL IO low level input -0.3 - 0.8 V VIH IO high level input 2.47 - 3.6 V VOL IO low level output - - 0.34 V VoH IO high level output 2.64 - 3.4 V Imax IO drive current - - 16 mA Cpad Input capacitor - 2 - pF 3.3 Wi-Fi Transmitting Current Consumptions Table 3.3. Wi-Fi TX current consumption PARAMETERS MODE RATE Transmitting power TYPICAL UNIT IRF 11b 1Mbps +21.89dBm 287 mA IRF 11g 6Mbps +22.15dBm 255 mA IRF 11n-HT20 MCS0 +21.27dBm 244 mA IRF 11n-HT40 MCS0 +21.03dBm 220 mA

DATASHEET 3.4 Wi-Fi Receiving Current Consumptions Table 3.4. Wi-Fi RX currentcon sumption PARAMETERS MODE TYPICAL UNIT IRF CPU sleep 90 mA IRF CPU active 120 mA 3.5 Working Mode Current Consumptions Table 3.5. The module working currentcon sumption WORK MODE AT TA=25℃ TYPICAL MAX* UNIT EZ Mode TYAUX_J is under EZ paring mode, Wi- 115 125 mA Fi indicator light flashes quickly Standby Mode TYAUX_J is connected, Wi-Fi indicator light is on 60 209 mA Operation Mode TYAUX_J is connected, Wi-Fi indicator light is on 118 198 mA Disconnection TYAUX_J is disconnected, Wi-Fi indicator light 34 192 mA Mode is off Note: peak continuous time is about 5us. The parameter shown above will vary depending on different firmware functions. 4. WLAN Radio Specification 4.1 Basic Radio Frequency Characteristics Table 41.Basic Radio frequency characteristics PARAMETERS DESCRIPTION Frequency band 2.412GHz to 2.462GHz Wi-Fi standard IEEE 802.11n/g/b (Terminal 1-11) Data transmitting rate 11b:1,2,5.5,11(Mbps) 11g:6,9,12,18,24,36,48,54(Mbps) 11n:HT20,MCS0~7 11n:HT40,MCS0~7 Antenna type On-board PCB Antenna 4.2Wi-Fi Receiving Sensitivity Table 4.2. Wi-Fi Receiving sensitivity PARAMETERS MIN TYPICAL MAX UNI T PER<8%, Receiving sensitivity, 802.11b CCK Mode 11M - -91 - dBm PER<10%, Receiving sensitivity, 802.11g OFDM Mode 54M - -75 - dBm PER<10%, Receiving sensitivity, 802.11n OFDM Mode MCS7 - -72 - dBm

DATASHEET 5. Antenna Information 5.1 Antenna Type Antenna can be connected using On-board PCB antenna. 5.2 Reduce Antenna Interference While using the On-board PCB antenna, in order to have the best Wi-Fi performance, it’s recommended to keep a minimum15mm distance between the antenna part and the other metal pieces.

DATASHEET 6. Packaging Information And Production Guide 6.1 Mechanical Dimensions Figure 6.1. Top view of the module 6.2 Production Guide  The storage for the delivered module should meet the following condition: 1. The anti-moisture bag should be kept in the environment with temperature< 30℃ and humidity< 85% RH. 2. The expiration date is 6 months since the dry packaging products was sealed.  Cautions: 1. All the operators should wear electrostatic ringin the whole process of production. 2. While operating, water and dirt should not have any contact with the modules. 6.3 Recommended furnace temperature curve Figure 6.4. PCB Package Drawing Recommended furnace temperature curve

DATASHEET FCC Statement Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. FCC Label Instructions: The outside of final products that contains this module device must display a label referring to the enclosed module. This exterior label can use wording such as: “Contains Transmitter Module FCC ID: 2ANDL-TYAUXJ”,or “Contains FCC ID: 2ANDL-TYAUXJ”, Any similar wording that expresses the same meaning may be used.


Document Created: 2019-03-06 14:53:02
Document Modified: 2019-03-06 14:53:02
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC