User Manual

FCC ID: 2ANCG-CS63031

Users Manual

Download: PDF
FCCID_4235051

Address：6F‐1, No.447, Sec.3, WenXin Rd., TaiChung City 40667, Taiwan (R.O.C) Tel：886‐4‐3703‐6518 Fax：886‐4‐3703‐6508 MANUAL 使用手冊 CUSTOMER Item P/N CS63031 DESCRIPTION BT Module Document Number CS63031 DATE This document contains confidential and proprietary information of CORESTARCo., Ltd and shall not be duplicated or otherwise transferred to a third party without the express written consent of CORESTAR. 本文件所包含內容所屬於合興數位股份有限公司(CorsStar Co., Ltd)之規格文件及專有技術資料所有，不得未經由合興 數位公司同意而擅自轉載或以不明確的書面或其他方式轉讓給第三方。

1. Hardware overview 1.1 Main Board PCB Physical Specifications 1.2 Connector Definitions J1 CTRL CON Pin No. DESCRIPTION Pin No. DESCRIPTION Pin No. DESCRIPTION Pin No. DESCRIPTION 1 +5V 2 GND 3 HV_RXD 4 HV_TXD 5 REV Operational description 1.3 The Conter Power Board provides power to the Upper Board, which supplies power to the BT Module 1.4 Mobile phone open Fitness_Sole APP search BT Module device use。 2. Operating frequency : 2402 ~ 2480MHz 3. Modulation type: GFSK 4. PCB antenna / 2dBi page 2 / 2

Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: . Reorient or relocate the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. . Consult the dealer or an experienced radio/TV technician for help. FCC Caution: To assure continued compliance, any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. (Example ‐ use only shielded interface cables when connecting to computer or peripheral devices). End Product Labeling This transmitter module is authorized only for use in devices where the antenna may be installed such that 0.5 cm may be maintained between the antenna and users. The final end product must be labeled in visible area with the following: “Contains FCC ID: 2ANCG‐CS63031” ” End Product Manual Information The user manual for end users must include the following information in a prominent location “IMPORTANT NOTE: To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 0.5cm from all persons and must not be colocated or operating in conjunction with any other antenna or transmitter.” This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) This device may not cause harmful interference and (2) This device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE: In the event that these conditions can not be met (for example certain laptop configurations or colocation with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for reevaluating the end product (including the transmitter) and obtaining a separate FCC authorization. This device is intended only for OEM integrators under the following conditions: The antenna must be installed such that 0.5 cm is maintained between the antenna and users. As long as a condition above is met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. page 4 / 4


Document Created: 2019-04-09 16:14:02
Document Modified: 2019-04-09 16:14:02
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC