Test Report_DTS

FCC ID: 2ANB8-T1

Test Report

Download: PDF
FCCID_4078477

Test Report FCC ID: 2ANB8-T1 Date of issue: Oct. 22, 2018 Report Number: MTi181018E052 Sample Description: GETWELL Aerobic capacity assessment and muscle oxygen monitoring Model(s): T1 Applicant: Getwell Health Technology（Wuhu）Co., Ltd. Address: 4th Building, Service outsourcing park, new and high-tech zone, Yijiang District, Wuhu, Anhui Date of Test: Oct. 11, 2018 - Oct. 22, 2018 Shenzhen Microtest Co., Ltd. http://www.mtitest.com This test report is valid for the tested samples only. It cannot be reproduced except in full without prior written consent of Shenzhen Microtest Co., Ltd. Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 2 of 27 - Report No.: MTi181018E052 Table of Contents 1. GENERAL INFORMATION ................................................................................................................................... 4 1.1. DESCRIPTION OF EUT ................................................................................................................................................... 4 1.2. OPERATION CHANNEL LIST .............................................................................................................................................. 4 1.3. TEST CHANNEL LIST ....................................................................................................................................................... 5 1.4. ANCILLARY EQUIPMENT LIST ........................................................................................................................................... 5 1.5. DESCRIPTION OF SUPPORT UNITS .................................................................................................................................... 5 2. SUMMARY OF TEST RESULTS .......................................................................................................................... 6 3. TEST FACILITIES AND ACCREDITATIONS ...................................................................................................... 7 3.1. TEST LABORATORY ........................................................................................................................................................ 7 3.2. ENVIRONMENTAL CONDITIONS ........................................................................................................................................ 7 3.3. MEASUREMENT UNCERTAINTY ........................................................................................................................................ 7 3.4. TEST SOFTWARE ........................................................................................................................................................... 7 4. EQUIPMENT LIST ................................................................................................................................................. 8 5. TEST RESULT ....................................................................................................................................................... 9 5.1. ANTENNA REQUIREMENT ............................................................................................................................................... 9 5.1.1 Standard requirement ......................................................................................................................................... 9 5.1.2 EUT Antenna ....................................................................................................................................................... 9 5.2. CONDUCTED EMISSION ................................................................................................................................................ 10 5.2.1 Limits ................................................................................................................................................................. 10 5.2.2 Test setup .......................................................................................................................................................... 10 5.2.3 Test procedure ................................................................................................................................................... 11 5.2.4 Test results......................................................................................................................................................... 11 5.3 RADIATED SPURIOUS EMISSION...................................................................................................................................... 16 5.3.1 Limits ................................................................................................................................................................. 16 5.3.2 Test setup .......................................................................................................................................................... 17 5.3.3 Test procedure ................................................................................................................................................... 18 5.3.4 Test results......................................................................................................................................................... 19 5.3.4.1 Radiation emission ....................................................................................................................................... 19 5.3.4.2 Bandedge-radiated ....................................................................................................................................... 23 5.3.4.3 Spurious Emission in Restricted Band 3260MMHz-18000MHz ..................................................................... 24 PHOTOGRAPHS OF THE TEST SETUP ................................................................................................................................ 25 PHOTOGRAPHS OF THE EUT ............................................................................................................................................ 27 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 3 of 27 - Report No.: MTi181018E052 PRODUCT INFORMATION Applicant’s name: Getwell Health Technology（Wuhu）Co., Ltd. 4th Building, Service outsourcing park, new and high-tech zone, Yijiang Address: District, Wuhu, Anhui Manufacture's Name: Getwell Health Technology（Wuhu）Co., Ltd. 4th Building, Service outsourcing park, new and high-tech zone, Yijiang Address: District, Wuhu, Anhui Product name: GETWELL Aerobic capacity assessment and muscle oxygen monitoring Trademark: getwell Model name: T1 Standards: FCC Part15 Subpat C ANSI C63.10:2013 KDB 558074 D01 DTS Meas Guidance v05 Test Procedure: KDB 174176 D01 Line Conducted FAQ v01r01 This device described above has been tested by Shenzhen Microtest Co., Ltd and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. Note: The RF component test data for this report is based on the original test report MTi170811E069 with a date of 2017-08-11. This report only reflects the retesting part, the conduction and radiation data are updated, and the rest of the data remains unchanged. Tested by:s Leo Su Oct. 22, 2018 Reviewed by: Blue Zheng Oct. 22, 2018 Approved by: Smith Chen Oct. 22, 2018 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 4 of 27 - Report No.: MTi181018E052 1. General Information 1.1. Description of EUT GETWELL Aerobic capacity assessment and muscle Product name: oxygen monitoring Model name: T1 Serial model: N/A Difference in series N/A models: Operation frequency: 2402-2480MHz Modulation type: GFSK Bit Rate of transmitter: 1 Mbps Antenna type: FPCB Antenna Antenna gain: 2dBi Max. output power: 1.348dBm Hardware version: V01 Software version: V218 Power supply: DC 3.7V by Battery or DC 5V from adapter AC 120V/60Hz Model:SK12G-0500100U Adapter information: Input:AC100-240V~ 50/60Hz 0.2A Output:5V 1A Battery: DC 3.7V 205mA 1.2. Operation channel list Channel Frequency Channel Frequency Channel Frequency Channel Frequency No. (MHz) No. (MHz) No. (MHz) No. (MHz) 0 2402 10 2422 20 2442 30 2462 1 2404 11 2424 21 2444 31 2464 2 2406 12 2426 22 2446 32 2466 3 2408 13 2428 23 2448 33 2468 4 2410 14 2430 24 2450 34 2470 5 2412 15 2432 25 2452 35 2472 6 2414 16 2434 26 2454 36 2474 7 2416 17 2436 27 2456 37 2476 8 2418 18 2438 28 2458 38 2478 9 2420 19 2440 29 2460 39 2480 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 5 of 27 - Report No.: MTi181018E052 1.3. Test channel list Channel Channel Frequency (MHz) Low 00 2402 Middle 19 2440 High 39 2480 1.4. Ancillary equipment list Equipment Model S/N Manufacturer Certificate type Adapter SK12G-0500100U / / / 1.5. Description of Support Units The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Item Equipment Brand Model/Type No. Series No. Note / / / / / / / / / / Note: (1)The support equipment was authorized by Declaration of Confirmation. (2)For detachable type I/O cable should be specified the length in cm in『Length』column. Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 6 of 27 - Report No.: MTi181018E052 2. Summary of Test Results Test procedures according to the technical standards: No. Standard Section Test Item Result Remark 1 15.207 Conducted Emission Pass 2 15.247 (d) & 15.209 Radiated Spurious Emission Pass 3 15.203 Antenna Requirement Pass Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 7 of 27 - Report No.: MTi181018E052 3. Test Facilities and Accreditations 3.1. Test laboratory Test Laboratory Shenzhen Microtest Co., Ltd No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Location Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China FCC Registration No.: 448573 3.2. Environmental conditions Temperature: 20ºC~30ºC Humidity 30%~70% Atmospheric pressure 98kPa~101kPa 3.3. Measurement uncertainty The reported uncertainty of measurement y ± U，where expended uncertainty U is based on a standard uncertainty multiplied by a coverage factor of k=2，providing a level of confidence of approximately 95 % No. Item Uncertainty 1 Conducted Emission Test ±1.38dB 2 RF power, conducted ±0.16dB 3 Spurious emissions, conducted ±0.21dB 4 All emissions, radiated(<1G) ±4.68dB 5 All emissions, radiated(>1G) ±4.89dB 6 Temperature ±0.5°C 7 Humidity ±2% 3.4. Test software Software Manufacturer Model Version Name RF Test System Farad LZ-RF Lz_Rf 3A3 Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 8 of 27 - Report No.: MTi181018E052 4. Equipment list Equipment Equipment Manufactur Calibration Model Serial No. Due date No. Name er date Spectrum MTI-E001 Agilent E4407B MY41441082 2017/11/18 2018/11/17 Analyzer CMU 200 universal radio Rohde&schw MTI-E002 CMU 200 114587 2017/11/18 2018/11/17 communication arz tester Rohde&schw MTI-E004 EMI Test Receiver ESPI 1000314 2017/11/18 2018/11/17 arz Broadband VULB916 MTI-E006 schwarabeck 872 2017/11/18 2018/11/17 antenna 3 BBHA912 MTI-E007 Horn antenna schwarabeck 1201 2017/11/18 2018/11/17 0D MTI-E014 amplifier America 8447D 3113A06150 2017/11/18 2018/11/17 Conduction 126A1343/20 MTI-E015 Immunity Signal Schloder CDG6000 2017/11/18 2018/11/17 15 Generator Coupled CDA A2210332/20 MTI-E016 decoupling Schloder 2017/11/18 2018/11/17 M2/M3 15 network Comprehensive Rohde&schw MTI-E032 CMW500 124192 2017/11/18 2018/11/17 test instrument arz MTI-E034 amplifier Agilent 8449B 3008A02400 2017/11/22 2018/11/21 Artificial power NSLK812 MTI-E037 Schwarzbeck #841 2017/12/26 2018/12/25 network 7 Spectrum MTI-E040 Agilent N9020A MY49100060 2017/11/05 2018/11/04 analyzer MTI-E041 Signal generator Agilent N5182A MY49060455 2017/11/23 2018/11/22 Analog signal MTI-E042 Agilent E4421B GB40051240 2017/11/23 2018/11/22 generator Dare RPR3006 16I00054SN MTI-E043 Power sensor 2017/12/29 2018/12/28 Instruments W O16 MTI-E047 10dB attenuator Mini-Circuits UNAT-10+ 15542 2017/11/24 2018/11/23 spectrum Rohde&schw MTI-E049 FSP-38 100019 2017/11/18 2018/11/17 analyzer arz PSG Signal MTI-E050 Agilent E8257D MY46520873 2017/11/24 2018/11/23 generator Active Loop FMZB MTI-E051 Antenna 9kHz - Schwarzbeek 00044 2017/11/26 2018/11/25 1519 B 30MHz Chengdu 18-40GHz ZLNA-18- MTI-E052 step Micro 1608001 2017/11/18 2018/11/17 amplifier 40G-21 Technology BBHA917 BBHA91705 MTI-E053 15-40G Antenna Schwarzbeek 2017/11/18 2018/11/17 0 82 Artificial power NSLK812 MTI-E058 Schwarzbeck #841 2017/11/05 2018/11/04 network 7 Note: the calibration interval of the above test instruments is 12 months and the calibrations are traceable to international system unit (SI). Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 9 of 27 - Report No.: MTi181018E052 5. Test Result 5.1. Antenna requirement 5.1.1 Standard requirement 15.203 requirement: For intentional device, according to 15.203: an intentional radiator shall be designed to ensure that no antenna other than that furnished by the responsible party shall be used with the device 5.1.2 EUT Antenna The EUT antenna is FPCB antenna (2dBi). It comply with the standard requirement. In case of replacement of broken antenna the same antenna type must be used. Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 10 of 27 - Report No.: MTi181018E052 5.2. Conducted emission 5.2.1 Limits Class B (dBuV) FREQUENCY (MHz) Quasi-peak Average 0.15 -0.5 66 - 56 * 56 - 46 * 0.50 -5.0 56.00 46.00 5.0 -30.0 60.00 50.00 Note (1)The tighter limit applies at the band edges. (2)The limit of " * " marked band means the limitation decreases linearly with the logarithm of the frequency in the range. 5.2.2 Test setup V e r tic a l R e fe r e n c e G r o u n d P la n e T e s t R e c e iv e r EUT 40cm 80cm L IS N H o r iz o n ta l R e f e r e n c e G r o u n d P la n e N o t e : 1 .S u p p o r t u n its w e r e c o n n e c t e d t o s e c o n d L IS N . 2 .B o th o f L IS N s ( A M N ) a r e 8 0 c m fr o m E U T a n d a t le a s t 8 0 cm f r o m o t h e r u n its a n d o t h e r m e ta l p la n e s s u p p o rt. u n i ts . Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 11 of 27 - Report No.: MTi181018E052 5.2.3 Test procedure a. EUT Operating Conditions The EUT was configured for testing in a typical fashion (as a customer would normally use it). The EUT has been programmed to continuously transmit during test. This operating condition was tested and used to collect the included data. b. The following table is the setting of the receiver Receiver Parameters Setting Attenuation 10 dB Start Frequency 0.15 MHz Stop Frequency 30 MHz IF Bandwidth 9 kHz c. The EUT was placed 0.8 meters from the horizontal ground plane with EUT being connected to the power mains through a line impedance stabilization network (LISN). All other support equipments powered from additional LISN(s). The LISN provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. d. Interconnecting cables that hang closer than 40 cm to the ground plane shall be folded back and forth in the center forming a bundle 30 to 40 cm long. e. I/O cables that are not connected to a peripheral shall be bundled in the center. The end of the cable may be terminated, if required, using the correct terminating impedance. The overall length shall not exceed 1 m. f. LISN at least 80 cm from nearest part of EUT chassis. For the actual test configuration, please refer to the related Item –EUT Test Photos. 5.2.4 Test results Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 12 of 27 - Report No.: MTi181018E052 Test data GETWELL Aerobic capacity EUT： assessment and muscle oxygen Model Name. ： T1 monitoring Temperature： 26 ℃ Relative Humidity： 54% Pressure： 1010hPa Phase : L Test Voltage ： DC 5V from adapter AC 120V/60Hz Test Mode： Normal link Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 13 of 27 - Report No.: MTi181018E052 GETWELL Aerobic capacity EUT： assessment and muscle oxygen Model Name： T1 monitoring Temperature： 26 ℃ Relative Humidity： 54% Pressure： 1010hPa Phase : N Test Voltage ： DC 5V from adapter AC 120V/60Hz Test Mode： Normal link Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 14 of 27 - Report No.: MTi181018E052 GETWELL Aerobic capacity EUT： assessment and muscle oxygen Model Name. ： T1 monitoring Temperature： 26 ℃ Relative Humidity： 54% Pressure： 1010hPa Phase : L Test Voltage ： DC 5V from adapter AC 240V/60Hz Test Mode： Normal link Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 15 of 27 - Report No.: MTi181018E052 GETWELL Aerobic capacity EUT： assessment and muscle oxygen Model Name. ： T1 monitoring Temperature： 26 ℃ Relative Humidity： 54% Pressure： 1010hPa Phase : N Test Voltage ： DC 5V from adapter AC 240V/60Hz Test Mode： Normal link Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 16 of 27 - Report No.: MTi181018E052 5.3 Radiated spurious emission 5.3.1 Limits Frequency Field Strength Measurement Distance (MHz) (micorvolts/meter) (meters) 0.009~0.490 2400/F(KHz) 300 0.490~1.705 24000/F(KHz) 30 1.705~30.0 30 30 30~88 100 3 88~216 150 3 216~960 200 3 Above 960 500 3 Spectrum Parameter Setting Attenuation Auto Start Frequency 1000 MHz Stop Frequency 10th carrier harmonic RB / VB (emission in restricted 1 MHz / 1 MHz for Peak, 1 MHz / 10Hz for band) Average Receiver Parameter Setting Attenuation Auto Start ~ Stop Frequency 9kHz~150kHz / RB 200Hz for QP Start ~ Stop Frequency 150kHz~30MHz / RB 9kHz for QP Start ~ Stop Frequency 30MHz~1000MHz / RB 120kHz for QP Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 17 of 27 - Report No.: MTi181018E052 5.3.2 Test setup Radiated emission test-up frequency below 30MHz Radiated emission test-up frequency 30MHz~1GHz Radiated emission test-up frequency above 1GHz 3m Turntabl 4m e EUT 1.5 1.5 m m Amplifie Test Receiver r Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 18 of 27 - Report No.: MTi181018E052 5.3.3 Test procedure a. EUT operating conditions. The EUT tested system was configured as the statements of 2.4 Unless otherwise a special operating condition is specified in the follows during the testing. b. The measuring distance of at 3 m shall be used for measurements at frequency up to 1GHz. For frequencies above 1GHz, any suitable measuring distance may be used. c. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 3 meter shield area test site. The table was rotated 360 degrees to determine the position of the highest radiation. d. The height of the equipment or of the substitution antenna shall be 0.8 m; the height of the test antenna shall vary between 1 m to 4 m. Both horizontal and vertical polarizations of the antenna are set to make the measurement. e. The initial step in collecting conducted emission data is a spectrum analyzer peak detector mode pre-scanning the measurement frequency range. Significant peaks are then marked and then Quasi Peak detector mode re-measured. f. If the Peak Mode measured value compliance with and lower than Quasi Peak Mode Limit, the EUT shall be deemed to meet QP Limits and then no additional QP Mode measurement performed. g. For the actual test configuration, please refer to the related Item –EUT Test photos. Note: Both horizontal and vertical antenna polarities were tested and performed pretest to three orthogonal axis. The worst case emissions were reported. During the radiated emission test, the Spectrum Analyzer was set with the following configurations: Frequency Band (MHz) Function Resolution bandwidth Video Bandwidth 30 to 1000 QP 120 kHz 300 kHz Peak 1 MHz 1 MHz Above 1000 Average 1 MHz 10 Hz Note: for the frequency ranges below 30 MHz, a narrower RBW is used for these ranges but the measured value should add a RBW correction factor (RBWCF) where RBWCF [dB] =10*lg(100 [kHz]/narrower RBW [kHz]). , the narrower RBW is 1 kHz and RBWCF is 20 dB for the frequency 9 kHz to 150 kHz, and the narrower RBW is 10 kHz and RBWCF is 10 dB for the frequency 150 kHz to 30 MHz. Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 19 of 27 - Report No.: MTi181018E052 5.3.4 Test results 5.3.4.1 Radiation emission Below 30MHz GETWELL Aerobic EUT： capacity assessment and Model Name： T1 muscle oxygen monitoring Temperature： 20 ℃ Relative Humidtity：48% Pressure： 1010 hPa Test Voltage： DC 5V from adapter Test Mode： TX Polarization : -- Freq. Reading Limit Margin State (MHz) (dBuV/m) (dBuV/m) (dB) P/F -- -- -- -- Pass -- -- -- -- Pass Note: The amplitude of spurious emissions which are attenuated by more than 20dB below the permissible value has no need to be reported. Distance extrapolation factor =40 log (specific distance/test distance)(dB); Limit line = specific limits(dBuV) + distance extrapolation factor. Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 20 of 27 - Report No.: MTi181018E052 Between 30MHz – 1GHz: All the modulation modes have been tested, and the worst result was report as below: GETWELL Aerobic capacity EUT： assessment and muscle oxygen Model Name ： T1 monitoring Relative 52% Phase: H Humidity: DC 5V from adapter AC Pressure： 1010 hPa Test Voltage ： 120V/60Hz Test Mode ： Normal link Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 21 of 27 - Report No.: MTi181018E052 GETWELL Aerobic capacity EUT： assessment and muscle oxygen Model Name ： T1 monitoring Relative 52% Phase: V Humidity: DC 5V from adapter AC Pressure： 1010 hPa Test Voltage ： 120V/60Hz Test Mode ： Normal link Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 22 of 27 - Report No.: MTi181018E052 1G-25GHz Note: (1) All Readings are Peak Value (VBW=3MHz) and AV Value (VBW=10Hz). (2) Emission Level= Antenna Factor + Cable Loss + Read Level - Preamp Factor (3) All other emissions more than 20dB below the limit. All the modulation modes have been tested, and the worst result was report as below: Frequenc Read Cable Antenna Preamp Emission Limits Margin y Level loss Factor Factor Level Remark Comment (MHz) (dBμV) (dB) dB/m (dB) (dBμV/m) (dBμV/m) (dB) Low Channel (2402 MHz)-Above 1G 4804.34 62.80 5.21 35.59 44.30 59.30 74.00 -14.70 Pk Vertical 4804.34 41.49 5.21 35.59 44.30 37.99 54.00 -16.01 AV Vertical 7206.11 60.19 6.48 36.27 44.60 58.34 74.00 -15.66 Pk Vertical 7206.11 41.05 6.48 36.27 44.60 39.20 54.00 -14.80 AV Vertical 4804.17 62.99 5.21 35.55 44.30 59.45 74.00 -14.55 Pk Horizontal 4804.17 42.21 5.21 35.55 44.30 38.67 54.00 -15.33 AV Horizontal 7206.21 62.24 6.48 36.27 44.52 60.47 74.00 -13.53 Pk Horizontal 7206.21 41.04 6.48 36.27 44.52 39.27 54.00 -14.73 AV Horizontal Mid Channel (2440 MHz)-Above 1G 4880.47 62.46 5.21 35.66 44.20 59.13 74.00 -14.87 Pk Vertical 4880.47 44.26 5.21 35.66 44.20 40.93 54.00 -13.07 AV Vertical 7320.27 65.77 7.10 36.50 44.43 64.94 74.00 -9.06 Pk Vertical 7320.27 42.30 7.10 36.50 44.43 41.47 54.00 -12.53 AV Vertical 4880.37 63.05 5.21 35.66 44.20 59.72 74.00 -14.28 Pk Horizontal 4880.37 41.56 5.21 35.66 44.20 38.23 54.00 -15.77 AV Horizontal 7320.23 61.03 7.10 36.50 44.43 60.20 74.00 -13.80 Pk Horizontal 7320.23 44.04 7.10 36.50 44.43 43.21 54.00 -10.79 AV Horizontal High Channel (2480 MHz)- Above 1G 4960.48 64.30 5.21 35.52 44.21 60.82 74.00 -13.18 Pk Vertical 4960.48 43.04 5.21 35.52 44.21 39.56 54.00 -14.44 AV Vertical 7440.13 65.40 7.10 36.53 44.60 64.43 74.00 -9.57 Pk Vertical 7440.13 49.24 7.10 36.53 44.60 48.27 54.00 -5.73 AV Vertical 4960.33 62.96 5.21 35.52 44.21 59.48 74.00 -14.52 Pk Horizontal 4960.33 43.77 5.21 35.52 44.21 40.29 54.00 -13.71 AV Horizontal 7440.2 63.53 7.10 36.53 44.60 62.56 74.00 -11.44 Pk Horizontal 7440.2 45.89 7.10 36.53 44.60 44.92 54.00 -9.08 AV Horizontal Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 23 of 27 - Report No.: MTi181018E052 5.3.4.2 Bandedge-radiated Note: (1) All Readings are Peak Value (VBW=3MHz) and AV Value (VBW=10Hz). (2)Emission Level= Antenna Factor + Cable Loss + Read Level - Preamp Factor (3) All other emissions more than 20dB below the limit. All the modulation modes have been tested, and the worst result was report as below: Frequenc Meter Cable Antenna Preamp Emission Limits Margin Detector y Reading Loss Factor Factor Level Comment (MHz) (dBμV) (dB) dB/m (dB) (dBμV/m) (dBμV/m) (dB) Type GFSK 2310.00 64.17 2.97 27.80 43.80 51.14 74 -22.86 Pk Horizontal 2310.00 42.92 2.97 27.80 43.80 29.89 54 -24.11 AV Horizontal 2310.00 61.69 2.97 27.80 43.80 48.66 74 -25.34 Pk Vertical 2310.00 41.72 2.97 27.80 43.80 28.69 54 -25.31 AV Vertical 2390.00 63.70 3.14 27.21 43.80 50.25 74 -23.75 Pk Vertical 2390.00 43.29 3.14 27.21 43.80 29.84 54 -24.16 AV Vertical 2390.00 63.93 3.14 27.21 43.80 50.48 74 -23.52 Pk Horizontal 2390.00 42.37 3.14 27.21 43.80 28.92 54 -25.08 AV Horizontal 2483.50 62.43 3.58 27.70 44.00 49.71 74 -24.29 Pk Vertical 2483.50 42.26 3.58 27.70 44.00 29.54 54 -24.46 AV Vertical 2483.50 65.73 3.58 27.70 44.00 53.01 74 -20.99 Pk Horizontal 2483.50 43.51 3.58 27.70 44.00 30.79 54 -23.21 AV Horizontal Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 24 of 27 - Report No.: MTi181018E052 5.3.4.3 Spurious Emission in Restricted Band 3260MMHz-18000MHz All the modulation modes have been tested, and the worst result was report as below: Antenn Frequenc Readin Cable Preamp Emission Detecto a Limits Margin y g Level Loss Factor Level r Factor Comment (dBμ (dBμ (MHz) (dBμV) (dB) dB/m (dB) (dB) Type V/m) V/m) 3260 62.70 4.04 29.57 44.70 51.61 74 -22.39 Pk Vertical 3260 55.78 4.04 29.57 44.70 44.69 54 -9.31 AV Vertical 3260 65.42 4.04 29.57 44.70 54.33 74 -19.67 Pk Horizontal 3260 56.86 4.04 29.57 44.70 45.77 54 -8.23 AV Horizontal 3332 64.81 4.26 29.87 44.40 54.54 74 -19.46 Pk Vertical 3332 56.98 4.26 29.87 44.40 46.71 54 -7.29 AV Vertical 3332 63.84 4.26 29.87 44.40 53.57 74 -20.43 Pk Horizontal 3332 50.35 4.26 29.87 44.40 40.08 54 -13.92 AV Horizontal 17797 44.50 10.99 43.95 43.50 55.94 74 -18.06 Pk Vertical 17797 34.00 10.99 43.95 43.50 45.44 54 -8.56 AV Vertical 17788 42.95 11.81 43.69 44.60 53.85 74 -20.15 Pk Horizontal 17788 34.88 11.81 43.69 44.60 45.78 54 -8.22 AV Horizontal Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 25 of 27 - Report No.: MTi181018E052 Photographs of the Test Setup Radiated emission Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 26 of 27 - Report No.: MTi181018E052 Conducted emission Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China

- Page 27 of 27 - Report No.: MTi181018E052 Photographs of the EUT See the APPENDIX 1: EUT PHOTO in the report No.: MTi181018E051-1. ----END OF REPORT---- Tel:(86-755)88850135 Fax: (86-755) 88850136 Web: http://www.mtitest.com E-mail: mti@51mti.com Address: No.102A & 302A, East Block, Hengfang Industrial Park, Xingye Road, Xixiang, Bao'an District, Shenzhen, Guangdong, China


Document Created: 2018-11-16 14:23:12
Document Modified: 2018-11-16 14:23:12
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC