Modular Approval Request

FCC ID: 2AN9Q-THIAMISX

Cover Letter(s)

Download: PDF
FCCID_3983319

FCC Modular Approval Request To the FCC or FCC TCB handling this application Hereby we, Company (grantee) Netronix Group.INC Add resss 3401 Greys Ferry Avenue Philadelphia, PA 19146 City / ZIP / State / Country United States request modular approval for the certification of our equipment within this application, identified by: FCC ID: 2ANYQ—THIAMISX The table below contains justification for modular approval of this equipment. Requirement per DA 00—1407 Explanation from grantee 1. The modular transmitter must have its own RF shielding. Has RF shielding. 2.The modular transmitter must have buffered modulation/data inputs (if such inputs are The modular have buffered provided) to ensure that the module will comply with Part 15 requirements under conditions modulation/data of excessive data rates or over—modulation. inputs.(TM4C129CNCZADI3R) 3. The modular transmitter must have its own power supply regulation. The modular transmitter haveits own power supply regulation.(Chip MCARD regulation DC 3.3V) 4.The modular transmitter must comply with the antenna requirements of Section 15.203 and This module is equipped with a chip 15.204(c). The antenna must either be permanently attached or employ a "unique" antenna antenna, the two antenna connectors are coupler (at all connections between the module and the antenna, including the cable).. not connected to the external antenna, please refer to the External Photo for the detail. 5. The modular transmitter must be tested in a stand—alone configuration, l.e., the module The module was tested in a stand—alone must not be inside another device during testing. This is intended to demonstrate that the configuration, please refer to the Setup module is capable of complying with Part 15 emission limits regardless of the device into Photo for the detail which it is eventually installed. 6. The modular transmitter must be labeled with its own FCC ID number, and, if the FCC ID Please refer to label sample exhibit — host is not visible when the module is installed inside another device, then the outside of the labeling is described in integration manual device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: "Contains Transmitter Module FCC ID: 2AN3Q—THIAMISX" or "Contains FCC ID: 2AN3Q—THIAMISX." Any similar wording that expresses the same meaning may be used. The Grantee may either provide such a label, an example of which must be included in the application for equipment authorization, or, must provide adequate instructions along with the module which explain this requirement. In the latter case, a copy of these instructions must be included in the application for equipment authorization. 7. The modular transmitter must comply with any specific rule or operating requirements The required FCC rule has been fulfilled applicable to the transmitter and the manufacturer must provide adequate instructions along and all the instructions for the maintaining with the module to explain any such requirements. A copy of these instructions must be compliance have been clearly stated in the included in the application for equipment authorization. For example, there are very strict User Manual. operational and timing requirements that must be met before a transmitter is authorized for operation under Section 15.231. For instance, data transmission is prohibited, except for operation under Section 15.231(e), in which case there are separate field strength level and timing requirements. Compliance with these requirements must be assured. 8. The modular transmitter must comply with any applicable RF exposure requirements. For The MPE evaluation with 20cm distance example, FCC Rules in Sections 2.1091, 2.1093 and specific Sections of Part 15, including restriction is submitted for the compliance 15.319(i), 15.407(f), 15.253(f) and 15.255(g), require that Unlicensed PCS, UNII and of RF Exposure requirement. millimetre wave devices perform routine environmental evaluation for RF Exposure to demonstrate compliance. In addition, spread spectrum transmitters operating under Section 15.247 are required to address RF Exposure compliance in accordance with Section 15.247(b)(4). Modular transmitters approved under other Sections of Part 15, when necessary, may also need to address certain RF Exposure concerns, typically by providing specific installation and operating instructions for users, installers and other interested parties to ensure compliance. Attestation (by grantee} City and Country: Date: Name: Function: Signature: (this must be a person) (or official company stamp) Philadelphia/USA 2018.08.23 Vasileios Nasis President j/‘/[,5


Document Created: 2018-08-29 08:59:51
Document Modified: 2018-08-29 08:59:51
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC