RF Test Report

FCC ID: 2AN9IU6

Test Report

Download: PDF

FCCID_3729387

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

FCC TEST REPORT

FOR

Dongguan Anycon Intelligent Technology Co.,Ltd

2.4G Remote Control

Test Model: U6-ANY-001

Prepared for : Dongguan Anycon Intelligent Technology Co.,Ltd
Address : No12, Limin Road, Jinxiaotang Industrial Park, Fenggang,
Dongguan, Guangdong, China

Prepared by : Shenzhen LCS Compliance Testing Laboratory Ltd
Address : 1/F., Xingyuan Industrial Park, Tongda Road, Bao’an Avenue, Bao’an
District, Shenzhen, Guangdong, China
Tel : (+86)755-82591330
Fax : (+86)755-82591332
Web : www.LCS-cert.com
Mail : webmaster@LCS-cert.com

Date of receipt of test sample : August 21, 2017
Number of tested samples : 1
Sample number : A17051505
Date of Test : August 21, 2017- December 19, 2017
Date of Report : December 19, 2017

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 1 of 31

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

FCC -- TEST REPORT

December 19, 2017
Test Report No. : LCS170817059AE Date of issue

Test Model.............................. : U6-ANY-001

EUT......................................... : 2.4G Remote Control

Applicant............................... : Dongguan Anycon Intelligent Technology Co.,Ltd
Address.................................. : No12, Limin Road, Jinxiaotang Industrial Park, Fenggang,
Dongguan, Guangdong, China
Telephone............................... : /
Fax.......................................... : /

Manufacturer........................ : Dongguan Anycon Intelligent Technology Co.,Ltd
Address................................... : No12, Limin Road, Jinxiaotang Industrial Park, Fenggang,
Dongguan, Guangdong, China
Telephone............................... : /
Fax.......................................... : /

Factory................................... : Dongguan Anycon Intelligent Technology Co.,Ltd
Address................................... : No12, Limin Road, Jinxiaotang Industrial Park, Fenggang,
Dongguan, Guangdong, China
Telephone............................... : /
Fax.......................................... : /

Test Result Positive
The test report merely corresponds to the test sample.
It is not permitted to copy extracts of these test result without the written permission of the test
laboratory.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 3 of 31

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

Revision History

Revision Issue Date Revisions Revised By
00 December 19, 2017 Initial Issue Gavin Liang

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 4 of 31

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

TABLE OF CONTENTS

1. GENERAL INFORMATION .............................................................................................. 7
1.1. Description of Device (EUT) ...................................................................................................... 7
1.2. Support Equipment List ............................................................................................................... 7
1.3. External I/O ................................................................................................................................. 7
1.4. Description of Test Facility ......................................................................................................... 8
1.5. Statement of the measurement uncertainty.................................................................................. 8
1.6. Measurement Uncertainty ........................................................................................................... 8
1.7. Description Of Test Modes ......................................................................................................... 9
2. TEST METHODOLOGY .................................................................................................. 10
2.1. EUT Configuration .................................................................................................................... 10
2.2. EUT Exercise............................................................................................................................. 10
2.3. General Test Procedures ............................................................................................................ 10
3. CONNECTION DIAGRAM OF TEST SYSTEM ........................................................... 11
3.1. Justification ............................................................................................................................... 11
3.2. EUT Exercise Software ............................................................................................................. 11
3.3. Special Accessories ................................................................................................................... 11
3.4. Block Diagram/Schematics ....................................................................................................... 11
3.5. Equipment Modifications .......................................................................................................... 11
3.6. Test Setup .................................................................................................................................. 11
4. SUMMARY OF TEST RESULTS .................................................................................... 12
5. ANTENNA REQUIREMENT ........................................................................................... 13
5.1. Standard Applicable .................................................................................................................. 13
5.2. Antenna Connected Construction .............................................................................................. 13
6. POWER LINE CONDUCTED EMISSIONS................................................................... 14
6.1 Standard Applicable ................................................................................................................... 14
6.2 Block Diagram of Test Setup ..................................................................................................... 14
6.3 Test Results ................................................................................................................................ 14
7. RADIATED EMISSION MEASUREMENT ................................................................... 16
7.1. Standard Applicable .................................................................................................................. 16
7.2. Instruments Setting .................................................................................................................... 16
7.3. Test Procedure ........................................................................................................................... 17
7.4. Block Diagram of Test Setup .................................................................................................... 21
7.5. Test Results ............................................................................................................................... 22
7.6. Results for Radiated Emissions (Above 1GHz) ........................................................................ 24
7.7. Results for Band edge Testing................................................................................................... 25
8. 20 DB BANDWIDTH MEASUREMENT ........................................................................ 27
8.1. Standard Applicable .................................................................................................................. 27
8.2. Block Diagram of Test Setup .................................................................................................... 27
8.3. Test Procedure ........................................................................................................................... 27
8.4. Test Results ............................................................................................................................... 28
9. ANTENNA REQUIREMENTS ......................................................................................... 29
9.1 Standard Applicable ................................................................................................................... 29
9.2 Antenna Connected Construction ............................................................................................... 29
10. LIST OF MEASURING EQUIPMENTS ....................................................................... 30
11.TEST SETUP PHOTOGRAPHS ..................................................................................... 31
12. EXTERIOR PHOTOGRAPHS OF THE EUT .............................................................. 31
This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 5 of 31

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

13. INTERIOR PHOTOGRAPHS OF THE EUT ............................................................... 31

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 6 of 31

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

1.4. Description of Test Facility

FCC Registration Number. is 254912.
Industry Canada Registration Number. is 9642A-1.
ESMD Registration Number. is ARCB0108.
UL Registration Number. is 100571-492.
TUV SUD Registration Number. is SCN1081.
TUV RH Registration Number. is UA 50296516-001
NVLAP Registration Code is 600167-0

1.5. Statement of the measurement uncertainty
The data and results referenced in this document are true and accurate. The reader is
cautioned that there may be errors within the calibration limits of the equipment and
facilities. The measurement uncertainty was calculated for all measurements listed in
this test report acc. To CISPR 16 – 4 “Specification for radio disturbance and immunity
measuring apparatus and methods – Part 4: Uncertainty in EMC Measurements” and is
documented in the LCS quality system acc. To DIN EN ISO/IEC 17025. Furthermore,
component and process variability of devices similar to that tested may result in
additional deviation. The manufacturer has the sole responsibility of continued
compliance of the device.

1.6. Measurement Uncertainty
Test Item Frequency Range Uncertainty Note
9KHz~30MHz 3.10dB (1)
30MHz~200MHz 2.96dB (1)
Radiation Uncertainty :
200MHz~1000MHz 3.10dB (1)
1GHz~26.5GHz 4.00dB (1)
Conduction Uncertainty : 150kHz~30MHz 1.63dB (1)
Power disturbance : 30MHz~300MHz 1.60dB (1)

(1). This uncertainty represents an expanded uncertainty expressed at approximately the
95% confidence level using a coverage factor of k=2.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 8 of 31

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

1.7. Description Of Test Modes

The EUT operates in the unlicensed ISM band at 2.4GHz. The following operating
modes were applied for the related test items.

All test modes were tested, only the result of the worst case was recorded in the report.
It was pre-tested on the positioned of each 3 axis. The worst case was found positioned
on X-plane.

Mode of Operations Transmitting Frequency
(MHz)
2404
GFSK 2440
2480
For Conducted Emission
Test Mode TX Mode
For Radiated Emission
Test Mode TX Mode

Worst-case mode and channel used for 9kHz-1000 MHz radiated emissions was the
mode and channel with the highest output power, that was determined to be TX-High
Channel(2480MHz).

Pre-test AC conducted emission at charge from PC mode, recorded worst case.
Pre-test AC conducted emission at both voltage AC 120V/60Hz and AC 240V/50Hz,
recorded worst case.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 9 of 31

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

2. TEST METHODOLOGY
All measurements contained in this report were conducted with ANSI C63.10: 2013,
American National Standard of Procedures for Compliance Testing of Unlicensed
Wireless Devices.
The radiated testing was performed at an antenna-to-EUT distance of 3 meters. All
radiated and conducted emissions measurement was performed at Shenzhen LCS
Compliance Testing Laboratory Ltd..

2.1. EUT Configuration
The EUT configuration for testing is installed on RF field strength measurement to meet
the Commissions requirement and operating in a manner that intends to maximize its
emission characteristics in a continuous normal application.

2.2. EUT Exercise
The EUT was operated in the engineering mode to fix the TX frequency that was for the
purpose of the measurements.
According to its specifications, the EUT must comply with the requirements of the
Section 15.203, 15.205, 15.207, 15.209 and 15.249 under the FCC Rules Part 15
Subpart C.

2.3. General Test Procedures
2.3.1 Conducted Emissions
According to the requirements in Section 6.2 of ANSI C63.10: 2013, AC power-line
conducted emissions shall be measured in the frequency range between 0.15 MHz and
30MHz using Quasi-peak and average detector modes.

2.3.2 Radiated Emissions
The EUT is placed on a turn table and the turntable shall rotate 360 degrees to
determine the position of maximum emission level. EUT is set 3m away from the
receiving antenna, which varied from 1m to 4m to find out the highest emission. And
also, each emission was to be maximized by changing the polarization of receiving
antenna both horizontal and vertical. In order to find out the maximum emissions,
exploratory radiated emission measurements were made according to the requirements
in Section 6.3 of ANSI C63.10: 2013

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 10 of 31

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

3. CONNECTION DIAGRAM OF TEST SYSTEM

3.1. Justification
The system was configured for testing in a continuous transmit condition.

3.2. EUT Exercise Software
The system was configured for testing in a continuous transmits condition and change test channels
by software (MP_Kit_Smart Tool) provided by application.

3.3. Special Accessories
Length shielded/
Equipment Manufacturer Model No. Serial No. unshielded Notes

PC Lenovo Ideapad A131101550 / / DOC
Power
Lenovo CPA-A090 36200414 1.00m unshielded DOC
adapter

3.4. Block Diagram/Schematics
Please refer to the related document

3.5. Equipment Modifications
Shenzhen LCS Compliance Testing Laboratory Ltd. has not done any modification on
the EUT.

3.6. Test Setup
Please refer to the test setup photo.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 11 of 31

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

4. SUMMARY OF TEST RESULTS

FCC Rules Description Of Test Result

§15.203 Antenna Requirement Compliant

§15.207(a) Power Line Conducted Emissions Compliant
§15.205(a), §15.209(a),
Radiated Emissions Measurement Compliant
§15.249(a), §15.249(c)
§15.249 Band Edges Measurement Compliant

§15.249, §15.215 20 dB Bandwidth Compliant

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 12 of 31

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

5. ANTENNA REQUIREMENT

5.1. Standard Applicable
According to §15.203, An intentional radiator shall be designed to ensure that no
antenna other than that furnished by the responsible party shall be used with the device.
The use of a permanently attached antenna or of an antenna that uses a unique coupling
to the intentional radiator shall be considered sufficient to comply with the provisions of
this section. The manufacturer may design the unit so that a broken antenna can be
replaced by the user, but the use of a standard antenna jack or electrical connector is
prohibited.

5.2. Antenna Connected Construction
The antenna used for transmitting is permanently attached and no consideration of
replacement. Please see EUT photo for details.

Result: Compliance.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 13 of 31

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

6. POWER LINE CONDUCTED EMISSIONS

6.1 Standard Applicable
According to §15.207 (a): For an intentional radiator which is designed to be connected to the
public utility (AC) power line, the radio frequency voltage that is conducted back onto the AC
power line on any frequency or frequencies within the band 150 kHz to 30 MHz shall not exceed
250 microvolts (The limit decreases linearly with the logarithm of the frequency in the range 0.15
MHz to 0.50 MHz). The limits at specific frequency range is listed as follows:

Frequency Range Limits (dBμV)
(MHz) Quasi-peak Average
0.15 to 0.50 66 to 56 56 to 46
0.50 to 5 56 46
5 to 30 60 50

6.2 Block Diagram of Test Setup

Vert. reference
plane
EMI receiver

EUT

LISN Reference ground plane

6.3 Test Results

PASS.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 14 of 31

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

7. RADIATED EMISSION MEASUREMENT

7.1. Standard Applicable
Emissions radiated outside of the specified frequency bands, except for harmonics, shall
be attenuated by at least 50 dB below the level of the fundamental or to the general
radiated emission limits in §15.209, whichever is the lesser attenuation.
20dBc in any 100 kHz bandwidth outside the operating frequency band. In case the
emission fall within the restricted band specified on 15.205(a), then the 15.209(a) and
15.249 limit in the table below has to be followed.

Fundamental Field Strength of fundamental Field Strength of harmonics
Frequency (millivolts/meter) (microvolts/meter)
902-928MHz 50 500
2400-2483.5MHz 50 500

5725-5875MHz 50 500

24.0-24.25GHz 250 2500

Frequencies Field Strength Measurement Distance
(MHz) (microvolts/meter) (meters)
0.009~0.490 2400/F(KHz) 300
0.490~1.705 24000/F(KHz) 30
1.705~30.0 30 30
30~88 100 3
88~216 150 3
216~960 200 3
Above 960 500 3

7.2. Instruments Setting
The following table is the setting of spectrum analyzer and receiver.

Spectrum Parameter Setting
Attenuation Auto
Start ~ Stop Frequency 9kHz~150kHz / RB 200Hz for QP
Start ~ Stop Frequency 150kHz~30MHz / RB 9kHz for QP

Start ~ Stop Frequency 30MHz~1000MHz / RB 120kHz for QP

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 16 of 31

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

Spectrum Parameter Setting
Attenuation Auto
Start Frequency 1000 MHz
Stop Frequency 10th carrier harmonic
RB / VB (Emission in restricted band) 1MHz / 1MHz for Peak, 1 MHz / 10Hz for Average
RB / VB (Emission in non-restricted band) 1000KHz / 1000KHz for peak

7.3. Test Procedure
1) Sequence of testing 9 kHz to 30 MHz

Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or
described by manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 0.8 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions.
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.

Premeasurement:
--- The turntable rotates from 0°to 315°using 45°steps.
--- The antenna height is 0.8 meter.
--- At each turntable position the analyzer sweeps with peak detection to find the maximum of all
emissions

Final measurement:
--- Identified emissions during the premeasurement the software maximizes by rotating the turntable
position (0°to 360°) and by rotating the elevation axes (0°to 360°).
--- The final measurement will be done in the position (turntable and elevation) causing the highest
emissions with QPK detector.
--- The final levels, frequency, measuring time, bandwidth, turntable position, correction factor,
margin to the limit and limit will be recorded. Also a plot with the graph of the premeasurement and
the limit will be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 17 of 31

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

2) Sequence of testing 30 MHz to 1 GHz

Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or
described by manufacturer.
--- If the EUT is a tabletop system, a table with 0.8 m height is used, which is placed on the ground
plane.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.

Premeasurement:
--- The turntable rotates from 0°to 315°using 45°steps.
--- The antenna is polarized vertical and horizontal.
--- The antenna height changes from 1 to 3 meter.
--- At each turntable position, antenna polarization and height the analyzer sweeps three times in
peak to find the maximum of all emissions.

Final measurement:
--- The final measurement will be performed with minimum the six highest peaks.
--- According to the maximum antenna and turntable positions of premeasurement the software
maximize the peaks by changing turntable position (± 45°) and antenna movement between 1 and 4
meter.
--- The final measurement will be done with QP detector with an EMI receiver.
--- The final levels, frequency, measuring time, bandwidth, antenna height, antenna polarization,
turntable angle, correction factor, margin to the limit and limit will be recorded. Also a plot with the
graph of the premeasurement with marked maximum final measurements and the limit will be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 18 of 31

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

3) Sequence of testing 1 GHz to 18 GHz

Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or
described by manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 1.5 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 3 meter.
--- The EUT was set into operation.

Premeasurement:
--- The turntable rotates from 0°to 315°using 45°steps.
--- The antenna is polarized vertical and horizontal.
--- The antenna height scan range is 1 meter to 2.5 meter.
--- At each turntable position and antenna polarization the analyzer sweeps with peak detection to
find the maximum of all emissions.

Final measurement:
--- The final measurement will be performed with minimum the six highest peaks.
--- According to the maximum antenna and turntable positions of premeasurement the software
maximize the peaks by changing turntable position (± 45°) and antenna movement between 1 and 4
meter. This procedure is repeated for both antenna polarizations.
--- The final measurement will be done in the position (turntable, EUT-table and antenna polarization)
causing the highest emissions with Peak and Average detector.
--- The final levels, frequency, measuring time, bandwidth, turntable position, EUT-table position,
antenna polarization, correction factor, margin to the limit and limit will be recorded. Also a plot with
the graph of the premeasurement with marked maximum final measurements and the limit will be
stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 19 of 31

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

4) Sequence of testing above 18 GHz

Setup:
--- The equipment was set up to simulate a typical usage like described in the user manual or
described by manufacturer.
--- If the EUT is a tabletop system, a rotatable table with 1.5 m height is used.
--- If the EUT is a floor standing device, it is placed on the ground plane with insulation between both.
--- Auxiliary equipment and cables were positioned to simulate normal operation conditions
--- The AC power port of the EUT (if available) is connected to a power outlet below the turntable.
--- The measurement distance is 1 meter.
--- The EUT was set into operation.

Premeasurement:
--- The antenna is moved spherical over the EUT in different polarizations of the antenna.

Final measurement:
--- The final measurement will be performed at the position and antenna orientation for all detected
emissions that were found during the premeasurements with Peak and Average detector.
--- The final levels, frequency, measuring time, bandwidth, correction factor, margin to the
limit and limit will be recorded. Also a plot with the graph of the premeasurement and the
limit will be stored.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 20 of 31

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

7.6. Results for Radiated Emissions (Above 1GHz)

Field Strength Of Fundamental (TX-2404MHz)
Frequency Measure Result Measure Result Peak Limit AVG Limit
Pol. Result
(MHz) (PK, dBuV/m) (AVG, dBuV/m) (dBuV/m) (dBuV/m)
2404 H 85.44 79.47 114 94 Pass
2404 V 88.74 81.25 114 94 Pass

Reading Ant. Pre. Cab. Limit
Freq. Measured Margin
Level Fac. Fac. Loss dBuV/ Remark Pol.
MHz dBuV/m dB
dBuV dB/m dB dB m
4808.00 45.93 33.06 35.04 3.94 47.89 74 -26.11 Peak Horizontal
4808.00 35.84 33.06 35.04 3.94 37.80 54 -16.20 Average Horizontal
4808.00 46.03 33.06 35.04 3.94 47.99 74 -26.01 Peak Vertical
4808.00 37.95 33.06 35.04 3.94 39.91 54 -14.09 Average Vertical

Field Strength Of Fundamental (TX-2440MHz)
Frequency Measure Result Measure Result Peak Limit AVG Limit
Pol. Result
(MHz) (PK, dBuV/m) (AVG, dBuV/m) (dBuV/m) (dBuV/m)
2440.00 H 82.56 79.46 114 94 Pass
2440.00 V 85.30 80.35 114 94 Pass

Reading Ant. Pre. Cab. Limit
Freq. Measured Margin
Level Fac. Fac. Loss dBu Remark Pol.
MHz dBuV/m dB
dBuV dB/m dB dB V/m
4880.00 43.62 33.16 35.15 3.96 45.59 74 -28.41 Peak Horizontal
4880.00 36.96 33.16 35.15 3.96 38.93 54 -15.07 Average Horizontal
4880.00 48.92 33.16 35.15 3.96 50.89 74 -23.11 Peak Vertical
4880.00 40.90 33.16 35.15 3.96 42.87 54 -11.13 Average Vertical

Field Strength Of Fundamental (TX-2480MHz)
Frequency Measure Result Measure Result Peak Limit AVG Limit
Pol. Result
(MHz) (PK, dBuV/m) (AVG, dBuV/m) (dBuV/m) (dBuV/m)
2480.00 H 87.56 83.33 114 94 Pass
2480.00 V 89.33 85.45 114 94 Pass

Readin
Ant. Pre. Cab. Limit
Freq. g Measured Margin
Fac. Fac. Loss dBuV/ Remark Pol.
MHz Level dBuV/m dB
dB/m dB dB m
dBuV
4960.00 45.93 33.26 35.14 3.98 48.03 74 -25.97 Peak Horizontal
4960.00 36.89 33.26 35.14 3.98 38.99 54 -15.01 Average Horizontal
4960.00 50.39 33.26 35.14 3.98 52.49 74 -21.51 Peak Vertical
4960.00 41.56 33.26 35.14 3.98 43.66 54 -10.34 Average Vertical
Notes:
1. Measuring frequencies from 9k~10th harmonic (ex. 26GHz), No emission found between lowest internal used/generated
frequency to 30MHz.
2. Radiated emissions measured in frequency range from 9k~10th harmonic (ex. 26GHz) were made with an instrument
using Peak detector mode.
3. No emission was be recorded above 18GHz means the reading of emissions are attenuated more than 20dB below the
permissible limits or the field strength is too small to be measured.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 24 of 31

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

7.7. Results for Band edge Testing
Only record the worst test case as following:
GFSK
Covert
Ground
Conducted Antenna Radiated E
Frequency Reflection Limit
Power Gain Level At Detector Verdict
(MHz) Factor (dBuV/m)
(dBm) (dBi) 3m
(dB)
(dBuV/m)
2310.000 -50.484 2.0 0.0 46.776 Peak 74.00 PASS
2310.000 -62.559 2.0 0.0 34.701 AV 54.00 PASS
2390.000 -52.303 2.0 0.0 44.957 Peak 74.00 PASS
2390.000 -62.120 2.0 0.0 35.140 AV 54.00 PASS
2483.500 -48.775 2.0 0.0 48.485 Peak 74.00 PASS
2483.500 -60.270 2.0 0.0 36.990 AV 54.00 PASS
2500.000 -50.730 2.0 0.0 46.530 Peak 74.00 PASS
2500.000 -61.903 2.0 0.0 35.357 AV 54.00 PASS

NOTE: Since the out-of-band characteristics of the EUT transmit antenna will often be unknown, the
use of a conservative antenna gain value is necessary. Thus, when determining the EIRP based on the
measured conducted power, the upper bound on antenna gain for a device with a single RF output shall
be selected as the maximum in-band gain of the antenna across all operating bands, or 2 dBi,
whichever is greater. However, for devices that operate in multiple frequency bands while using the
same transmit antenna, the highest gain of the antenna within the operating band nearest in frequency
to the restricted band emission being measured may be used in lieu of the overall highest gain when the
emission is at a frequency that is within 20 percent of the nearest band edge frequency, but in no case
shall a value less than 2 dBi be used.
Please refer to following test plots;

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 25 of 31

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

9. ANTENNA REQUIREMENTS

9.1 Standard Applicable
According to antenna requirement of §15.203.

An intentional radiator shall be designed to ensure that no antenna other than that furnished by the
responsible party shall be used with the device. The use of a permanently attached antenna or of
an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to
comply with the provisions of this Section. The manufacturer may design the unit so that a broken
antenna can be re-placed by the user, but the use of a standard antenna jack or electrical connector
is prohibited. This requirement does not apply to carrier current devices or to devices operated
under the provisions of Sections 15.211, 15.213, 15.217, 15.219, or 15.221. Further, this
requirement does not apply to intentional radiators that must be professionally installed, such as
perimeter protection systems and some field disturbance sensors, or to other intentional radiators
which, in accordance with Section 15.31(d), must be measured at the installation site. However,
the installer shall be responsible for ensuring that the proper antenna is employed so that the limits
in this Part are not exceeded.

And according to §15.247(4)(1), system operating in the 2400-2483.5MHz bands that are used
exclusively for fixed, point-to-point operations may employ transmitting antennas with directional
gain greater than 6dBi provided the maximum peak output power of the intentional radiator is
reduced by 1 dB for every 3 dB that the directional gain of the antenna exceeds 6dBi.

9.2 Antenna Connected Construction
9.2.1. Standard Applicable

According to §15.203, an intentional radiator shall be designed to ensure that no antenna other
than that furnished by the responsible party shall be used with the device.

9.2.2. Antenna Connector Construction

The directional gains of antenna used for transmitting is -3.0dBi, and the antenna is an External
PCB antenna connect to PCB board and no consideration of replacement. Please see EUT photo
for details.

9.2.3. Results: Compliance.

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 29 of 31

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AN9IU6 Report No.: LCS170817059AE

11.TEST SETUP PHOTOGRAPHS
Please refer to separated files for Test Setup Photos of the EUT.

12. EXTERIOR PHOTOGRAPHS OF THE EUT
Please refer to separated files for External Photos of the EUT.

13. INTERIOR PHOTOGRAPHS OF THE EUT
Please refer to separated files for Internal Photos of the EUT.

------------THE END OF TEST REPORT----------

This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd.
Page 31 of 31

Document Created: 2018-01-26 09:31:35
Document Modified: 2018-01-26 09:31:35

© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC