BLE Smart watch Device HD01 BLE 15.249 FCC Test Report)

FCC ID: 2AMPH-HDWATCH

Test Report

Download: PDF
FCCID_4110736

Page 1 of 24Report No.:UNIA201812060405FR-01 FCC RADIO TEST REPORT FCC ID: 2AMPH-HDWATCH Product： BLE Smart watch Trade Name： N/A Model Name： HD01 HD Watch, moka, HD02, HD03, HD04, HD05, HD06, HD07, HD08, HD09, HD10, HD11, HD12, HD13, HD14, HD15, HD16, Serial Model： HD17, HD18, HD19, HD20, HD21, HD22, HD23, HD24, HD25, HD26, HD27, HD28, HD29, HD30 Report No.： UNIA201812060405FR-01 Prepared for Shenzhen AOWO Technology Co., LTD Room 305, Zhongxi ECO International Building, Xixiang, Baoan, Shenzhen, China Prepared by Shenzhen United Testing Technology Co., Ltd. 2F, Annex Bldg, Jiahuangyuan Tech Park, #365 Baotian 1 Rd, Tiegang Community, Xixiang Str, Bao'an District, Shenzhen, China

Page 2 of 24Report No.:UNIA201812060405FR-01 TEST RESULT CERTIFICATION Applicant’s name.................... : Shenzhen AOWO Technology Co., LTD Room 305, Zhongxi ECO International Building, Xixiang, Baoan, Address...................................... : Shenzhen, China Manufacture's Name.............. : Shenzhen EXE Technology Co.,Ltd F6, Bldg4, HuaFeng No.1 Science&Technology Zone, Baoan, Address...................................... : Shenzhen Product description Product name............................... : BLE Smart watch Trade Mark.................................: N/A HD01, HD Watch, moka, HD02, HD03, HD04, HD05, HD06, HD07, HD08, HD09, HD10, HD11, HD12, HD13, HD14, Model and/or type reference . : HD15, HD16, HD17, HD18, HD19, HD20, HD21, HD22, HD23, HD24, HD25, HD26, HD27, HD28, HD29, HD30 FCC Rules and Regulations Part 15 Subpart C Section 15.249, Standards..................................: ANSI C63.10: 2013 This device described above has been tested by Shenzhen United Testing Technology Co., Ltd., and the test results show that the equipment under test (EUT) is in compliance with the FCC requirements. And it is applicable only to the tested sample identified in the report. This report shall not be reproduced except in full, without the written approval of UNI, this document may be altered or revised by Shenzhen United Testing Technology Co., Ltd., personnel only, and shall be noted in the revision of the document. Date of Test............................................... : Date (s) of performance of tests...............: Dec. 06, 2018 ~ Dec. 13, 2018 Date of Issue.............................................. : Dec.13, 2018 Test Result.................................................. : Pass Prepared by: Kahn yang/Editor Reviewer: Sherwin Qian/Supervisor Approved & Authorized Signer: Liuze/Manager

Page 3 of 24Report No.:UNIA201812060405FR-01 Table of Contents Page 1 . TEST SUMMARY 4 2 . GENERAL INFORMATION 5 2.1 GENERAL DESCRIPTION OF EUT 5 2.2 Carrier Frequency of Channels 6 2.3 Operation of EUT during testing 6 2.4DESCRIPTION OF TEST SETUP 6 2.5MEASUREMENT INSTRUMENTS LIST 7 3 . CONDUCTED EMISSIONS TEST 8 3.1 Conducted Power Line Emission Limit 8 3.2 Test Setup 8 3.3 Test Procedure 8 3.4 Test Result 8 4 RADIATED EMISSION TEST 11 4.1 Radiation Limit 11 4.2 Test Setup 11 4.3 Test Procedure 12 4.4 Test Result 12 5 BAND EDGE 18 5.1 Limits 18 5.2 Test Procedure 18 5.3 Test Result 18 6 OCCUPIED BANDWIDTH MEASUREMENT 20 6.1 Test Setup 20 6.2 Test Procedure 20 6.3 Measurement Equipment Used 20 6.4 Test Result 20 7 ANTENNA REQUIREMENT 22 8 PHOTOGRAPH OF TEST 23 8.1 Radiated Emission 23 8.2Conducted Emission 24

Page 4 of 24Report No.:UNIA201812060405FR-01 1. TEST SUMMARY TEST PROCEDURES AND RESULTS DESCRIPTION OF TEST RESULT CONDUCTED EMISSIONS TEST COMPLIANT RADIATED EMISSION TEST COMPLIANT BAND EDGE COMPLIANT OCCUPIED BANDWIDTH MEASUREMENT COMPLIANT ANTENNA REQUIREMENT COMPLIANT TEST FACILITY Test Firm : Shenzhen United Testing Technology Co., Ltd. Address :2F, Annex Bldg, Jiahuangyuan Tech Park, #365 Baotian 1 Rd,Tiegang Community, Xixiang Str, Bao'an District, Shenzhen, China The testing quality ability of our laboratory meet with "Quality Law of People's Republic of China" Clause 19.The testing quality system of our laboratory meets with ISO/IEC-17025 requirements, which is approved by CNAS. This approval result is accepted by MRA of APLAC. Our test facility is recognized, certified, or accredited by the following organizations: CNAS-LAB Code: L6494 The EMC Laboratory has been assessed and in compliance with CNAS-CL01 accreditation criteria for testing Laboratories (identical to ISO/IEC 17025:2017 General Requirements) for the Competence of testing Laboratories. Designation Number: CN1227 Test Firm Registration Number: 674885 The EMC Laboratory has been registered and fully described in a report filed with the (FCC) Federal Communications commission. The acceptance letter from the FCC is maintained in our files. MEASUREMENT UNCERTAINTY Measurement Uncertainty Conducted Emission Expanded Uncertainty = 2.23dB, k=2 Radiated emission expanded uncertainty(9kHz-30MHz) = 3.08dB, k=2 Radiated emission expanded uncertainty(30MHz-1000MHz) = 4.42dB, k=2 Radiated emission expanded uncertainty(Above 1GHz) = 4.06dB, k=2

Page 5 of 24Report No.:UNIA201812060405FR-01 2. GENERAL INFORMATION GENERAL DESCRIPTION OF EUT Equipment BLE Smart watch Trade Mark N/A Model Name HD01 HD Watch, moka, HD02, HD03, HD04, HD05, HD06, HD07, HD08, HD09, HD10, HD11, HD12, HD13, HD14, Serial No. HD15, HD16, HD17, HD18, HD19, HD20, HD21, HD22, HD23, HD24, HD25, HD26, HD27, HD28, HD29, HD30 All model’s the function, software and electric circuit are the Model Difference same, only with a product color and model named different. Test sample model: HD01. FCC ID 2AMPH-HDWATCH Antenna Type Integral Antenna Antenna Gain 0dBi Frequency Range 2402~2480MHz Number of Channels 40CH Modulation Type GFSK Battery DC3.7V, 90mAh DC3.7V from Battery or DC 5V from adapter with PowerSource AC 120(240)V/60Hz M/N: P12USB050200 Adapter Model Input: AC 100-240V, 50/60Hz, 0.3A Output: DC 5V, 2.0A Note: 1.The EUT consists of a pair of headphones, divided into left and right headphone. The software and electric circuit of the two headphones are the same. 2.This report shows the right headphone.

Page 6 of 24Report No.:UNIA201812060405FR-01 Carrier Frequency of Channels Channel List Frequency Frequency Frequency Frequency Channel Channel Channel Channel (MHz) (MHz) (MHz) (MHz) 01 2402 11 2422 21 2442 31 2462 02 2404 12 2424 22 2444 32 2464 03 2406 13 2426 23 2446 33 2466 04 2408 14 2428 24 2448 34 2468 05 2410 15 2430 25 2450 35 2470 06 2412 16 2432 26 2452 36 2472 07 2414 17 2434 27 2454 37 2474 08 2416 18 2436 28 2456 38 2476 09 2418 19 2438 29 2458 39 2478 10 2420 20 2440 30 2460 40 2480 Operation of EUT during testing Operating Mode The mode is used: Transmitting mode Low Channel: 2402MHz Middle Channel: 2440MHz High Channel: 2480MHz DESCRIPTION OF TEST SETUP Operation of EUT during Conducted testing: AC Power Adapter EUT Operation of EUT duringRadiation testing: EUT Table forauxiliary equipment: Equipment Description Manufacturer Model Calibration Due Date Adapter XinShenHai P12USB020200 N/A

Page 7 of 24Report No.:UNIA201812060405FR-01 MEASUREMENT INSTRUMENTS LIST Item Equipment Manufacturer Model No. Serial No. Calibrated until CONDUCTED EMISSIONS TEST 1 AMN Schwarzbeck NNLK8121 8121370 2019.9.9 2 AMN ETS 3810/2 00020199 2019.9.9 EMI TEST 3 Rohde&Schwarz ESCI 101210 2019.9.9 RECEIVER 4 AAN TESEQ T8-Cat6 38888 2019.9.9 RADIATED EMISSION TEST 1 Horn Antenna Sunol DRH-118 A101415 2019.9.29 2 BicoNILog Antenna Sunol JB1 Antenna A090215 2019.9.29 3 PREAMP HP 8449B 3008A00160 2019.9.9 4 PREAMP HP 8447D 2944A07999 2019.9.9 EMI TEST 5 Rohde&Schwarz ESR3 101891 2019.9.9 RECEIVER VECTOR Signal 6 Rohde&Schwarz SMU200A 101521 2019.9.28 Generator 7 Signal Generator Agilent E4421B MY4335105 2019.9.28 8 MXA Signal Analyzer Agilent N9020A MY50510140 2019.9.28 9 MXA Signal Analyzer Agilent N9020A MY51110104 2019.9.9 ANT Tower&Turn 10 Champro EM 1000 60764 2019.9.28 table Controller 11 Anechoic Chamber Taihe Maorui 9m*6m*6m 966A0001 2019.9.9 12 Shielding Room Taihe Maorui 6.4m*4m*3m 643A0001 2019.9.9 13 RF Power sensor DARE RPR3006W 15I00041SNO88 2019.3.14 14 RF Power sensor DARE RPR3006W 15I00041SNO89 2019.3.14 15 RF power divider Anritsu K241B 992289 2019.9.28 Wideband radio 16 Rohde&Schwarz CMW500 154987 2019.9.28 communication tester 17 Biconical antenna Schwarzbeck VHA 9103 91032360 2019.9.8 18 Biconical antenna Schwarzbeck VHA 9103 91032361 2019.9.8 Broadband Hybrid 19 Schwarzbeck VULB9163 VULB9163#958 2019.9.8 Antennas 20 Horn Antenna Schwarzbeck BBHA9120D 9120D-1680 2019.1.12 Active Receive Loop 21 Schwarzbeck FMZB 1919B 00023 2019.11.1 Antenna 22 Horn Antenna Schwarzbeck BBHA 9170 BBHA9170651 2019.03.14 Microwave 23 Broadband Schwarzbeck BBV 9721 100472 2019.10.10 Preamplifier 24 Active Loop Antenna Com-Power AL-130R 10160009 2019.05.10 25 Power Meter KEYSIGHT N1911A MY50520168 2019.05.10 26 Frequency Meter VICTOR VC2000 997406086 2019.05.10 27 DC Power Source HYELEC HY5020E 055161818 2019.05.10

Page 8 of 24Report No.:UNIA201812060405FR-01 3. CONDUCTED EMISSIONS TEST 3.1 Conducted Power Line Emission Limit For unintentional device, according to § 15.107(a) Line Conducted Emission Limits is as following Maximum RF Line Voltage(dBV) Frequency CLASS A CLASS B (MHz) Q.P. Ave. Q.P. Ave. 0.15~0.50 79 66 66~56* 56~46* 0.50~5.00 73 60 56 46 5.00~30.0 73 60 60 50 * Decreasing linearly with the logarithm of the frequency For intentional device, according to §15.207(a) Line Conducted Emission Limit is same as above table. 3.2 Test Setup 3.3 Test Procedure 1, The equipment was set up as per the test configuration to simulate typical actual usage per the user’smanual. The EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and is placed onthe ground plane as per ANSI C63.10. 2, Support equipment, if needed, was placed as per ANSI C63.10. 3, All I/O cables were positioned to simulate typical actual usage as per ANSI C63.10. 4,If a EUT received DC power from the USB Port of Notebook PC, the PC’s adapter received AC120V/60Hzpower through a Line Impedance Stabilization Network (LISN) which supplied power source and wasgrounded to the ground plane. 5, All support equipments received AC power from a second LISN, if any. 6, The EUT test program was started. Emissions were measured on each current carrying line of the EUTusing a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has twomonitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line 1connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver. 7, Analyzer / Receiver scanned from 150 KHz to 30MHz for emissions in each of the test modes. 3.4 Test Result Pass Remark: 1. All modes were tested at AC 120V and 240V, only the worst result of AC 120V was reported. 2. All modes of Low, Middle, and High channel were tested, only the worst result of High Channel was reported as below:

Page 9 of 24Report No.:UNIA201812060405FR-01 Temperature: 24℃ Relative Humidity: 45% Test Date: Dec.13, 2018 Pressure: 1010hPa Test Voltage: AC 120V, 60Hz Phase: Line Test Mode: Transmitting mode of GFSK 2480MHz Remark: Factor = Insertion Loss + Cable Loss, Result=Reading + Factor, Margin=Result – Limit.

Page 10 of 24Report No.:UNIA201812060405FR-01 Temperature: 25℃ Relative Humidity: 47% Test Date: Dec.13, 2018 Pressure: 1010hPa Test Voltage: AC 120V, 60Hz Phase: Neutral Test Mode: Transmitting mode of GFSK 2480MHz Remark: Factor = Insertion Loss + Cable Loss, Result=Reading + Factor, Margin=Result – Limit.

Page 11 of 24Report No.:UNIA201812060405FR-01 4 RADIATED EMISSION TEST 4.1 Radiation Limit For unintentional device, according to § 15.109(a), except for Class A digital devices, the field strength ofradiated emissions from unintentional radiators at a distance of 3 meters shall not exceed the followingvalues： Frequency Distance Radiated Radiated (MHz) (Meters) (dBμV/m) (μV/m) 30-88 3 40 100 88-216 3 43.5 150 216-960 3 46 200 Above 960 3 54 500 For intentional device, according to § 15.209(a), the general requirement of field strength of radiatedemissions from intentional radiators at a distance of 3 meters shall not exceed the above table. 4.2 Test Setup 1. Radiated Emission Test-Up Frequency Below 30MHz 2. Radiated Emission Test-Up Frequency 30MHz~1GHz

Page 12 of 24Report No.:UNIA201812060405FR-01 3. Radiated Emission Test-Up Frequency Above 1GHz 4.3 Test Procedure 1. Below 1GHz measurement the EUT is placed on turntable which is 0.8m above ground plane. And above 1GHz measurement EUT was placed on low permittivity and low tangent turn table which is 1.5m above ground plane. 2. The turntable shall be rotated for 360 degrees to determine the position of maximum emission level. 3. EUT is set 3m away from the receiving antenna, which is varied from 1m to 4m to find out the highestemissions. 4. Maximum procedure was performed on the six highest emissions to ensure EUT compliance. 5. And also, each emission was to be maximized by changing the polarization of receiving antenna bothhorizontal and vertical. 6. Repeat above procedures until the measurements for all frequencies are complete. 7. The test frequency range from 9KHz to25GHz per FCC PART 15.33(a). Note: For battery operated equipment, the equipment tests shall be performed using a new battery. 4.4 Test Result PASS Remark: 1. All the test modes completed for test. The worst case of Radiated Emissionis High channel, the test data of this mode was reported. 2. By preliminary testing and verifying three axis (X, Y and Z) position of EUT transmitted status, it was found that “Z axis” position was the worst, and test data recorded in this report. 3. Radiated emission test from 9KHz to 10th harmonic of fundamental was verified, and no emission found except system noise floor in 9KHz to 30MHz and not recorded in this report.

Page 13 of 24Report No.:UNIA201812060405FR-01 Below 1GHz Test Results: Temperature: 24℃ Relative Humidity: 45% Test Date: Nov. 13, 2018 Pressure: 1010hPa Test Voltage: DC 3.7V from Battery Polarization: Horizontal Test Mode: Transmitting mode of GFSK 2480MHz Remark: Absolute Level= Reading Level+ Factor, Margin= Absolute Level – Limit Factor=Ant. Factor + Cable Loss – Pre-amplifier

Page 14 of 24Report No.:UNIA201812060405FR-01 Temperature: 25℃ Relative Humidity: 47% Test Date: Nov. 13, 2018 Pressure: 1010hPa Test Voltage: DC 3.7V from Battery Polarization: Vertical Test Mode: Transmitting mode of GFSK 2480MHz Remark: Absolute Level= Reading Level+ Factor, Margin= Absolute Level – Limit Factor=Ant. Factor + Cable Loss – Pre-amplifier Remark： (1) Measuring frequencies from 9 KHz to the 1 GHz, Radiated emission test from 9KHz to 30MHzwas verified, and no any emission was found except system noise floor. (2) * denotes emission frequency which appearing within the Restricted Bands specified in provision of 15.205, then the general radiated emission limits in 15.209 apply. (3) The IF bandwidth of EMI Test Receiver between 30MHz to 1GHz was 120KHz, 1 MHz for measuring above 1 GHz, below 30MHz was 10KHz.

Page 15 of 24Report No.:UNIA201812060405FR-01 Above 1 GHz Test Results: CH Low (2402MHz) Horizontal: Emission Frequency Meter Reading Factor Limits Margin Level Detector Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 2402 108.32 -5.84 102.48 114 -11.52 peak 2402 81.12 -5.84 75.28 94 -18.72 AVG 4804 61.13 -3.64 57.49 74 -16.51 peak 4804 50.16 -3.64 46.52 54 -7.48 AVG 7206 59.16 -0.95 58.21 74 -15.79 peak 7206 46.12 -0.95 45.17 54 -8.83 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin= Absolute Level – Limit Vertical: Emission Frequency Meter Reading Factor Limits Margin Level Detector Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 2402 107.36 -5.84 101.52 114 -12.48 peak 2402 81.91 -5.84 76.07 94 -17.93 AVG 4804 61.33 -3.64 57.69 74 -16.31 peak 4804 50.32 -3.64 46.68 54 -7.32 AVG 7206 57.14 -0.95 56.19 74 -17.81 peak 7206 46.51 -0.95 45.56 54 -8.44 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin= Absolute Level – Limit

Page 16 of 24Report No.:UNIA201812060405FR-01 CH Middle (2440MHz) Horizontal: Emission Frequency Meter Reading Factor Limits Margin Level Detector Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 2440 109.21 -5.71 103.50 114 -10.50 peak 2440 81.71 -5.71 76.00 94 -18.00 AVG 4880 61.12 -3.51 57.61 74 -16.39 peak 4880 50.43 -3.51 46.92 54 -7.08 AVG 7320 59.32 -0.82 58.50 74 -15.50 peak 7320 45.91 -0.82 45.09 54 -8.91 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin= Absolute Level – Limit Vertical: Emission Frequency Meter Reading Factor Limits Margin Level Detector Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 2440 107.65 -5.71 101.94 114 -12.06 peak 2440 81.99 -5.71 76.28 94 -17.72 AVG 4880 61.11 -3.51 57.60 74 -16.40 peak 4880 50.65 -3.51 47.14 54 -6.86 AVG 7320 56.71 -0.82 55.89 74 -18.11 peak 7320 46.39 -0.82 45.57 54 -8.43 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin= Absolute Level – Limit

Page 17 of 24Report No.:UNIA201812060405FR-01 CH High (2480MHz) Horizontal: Emission Frequency Meter Reading Factor Limits Margin Level Detector Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 2480 110.14 -5.65 104.49 114 -9.51 peak 2480 81.88 -5.65 76.23 94 -17.77 AVG 4960 61.45 -3.43 58.02 74 -15.98 peak 4960 50.39 -3.43 46.96 54 -7.04 AVG 7440 58.01 -0.75 57.26 74 -16.74 peak 7440 46.61 -0.75 45.86 54 -8.14 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin= Absolute Level – Limit Vertical: Emission Frequency Meter Reading Factor Limits Margin Level Detector Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 2480 108.19 -5.65 102.54 114 -11.46 peak 2480 82.33 -5.65 76.68 94 -17.32 AVG 4960 61.42 -3.43 57.99 74 -16.01 peak 4960 50.87 -3.43 47.44 54 -6.56 AVG 7440 56.16 -0.75 55.41 74 -18.59 peak 7440 47.01 -0.75 46.26 54 -7.74 AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Margin= Absolute Level – Limit Remark： (1) Measuring frequencies from 1 GHz to the 25 GHz. (2) “F” denotes fundamental frequency; “H” denotes spurious frequency. “E” denotes band edge frequency. (3) * denotes emission frequency which appearing within the Restricted Bands specified in provision of 15.205, then the general radiated emission limits in 15.209 apply. (4) Data of measurement within this frequency range shown “--- ” in the table above means the reading of emissions are attenuated more than 20dB below the permissible limits or the field strength is too small to be measured. (5) The IF bandwidth of EMI Test Receiver between 30MHz to 1GHz was 120KHz, 1 MHz for measuring above 1 GHz, below 30MHz was 10KHz.The resolution bandwidth of test receiver/spectrum analyzer is 1MHzand video bandwidth is 3MHz for peak measurement with peak detectorat frequency above 1GHz.The resolution bandwidth of test receiver/spectrum analyzer is 1MHzand video bandwidth is 10Hz for Average measurement with peak detection at frequency above 1GHz. (6) When the test results of Peak Detected below the limits of Average Detected, the Average Detected is not need completed. For example: Top Channel at Fundamental 73.16dBuV/m(PK Value) <93.98(AV Limit), at harmonic 53.20 dBuV/m(PK Value) <54 dBuV/m(AV Limit), the Average Detected not need to completed. (7)All modes of operation were investigated and the worst-case emissionsare reported.

Page 18 of 24Report No.:UNIA201812060405FR-01 5 BAND EDGE 5.1 Limits FCC PART 15.249(d) Emissions radiated outside of the specified frequency bands, except for harmonics,shall be attenuated by at least 50 dB below the level of the fundamental or to the general radiated emissionlimits in §15.209, whichever is the lesser attenuation. 5.2 Test Procedure The band edge compliance of RF radiated emission should be measured by following the guidance in ANSIC63.10 with respect to maximizing the emission by rotating the EUT, measuring the emission while the EUT issituated in three orthogonal planes (if appropriate), adjusting the measurement antenna height andpolarization etc. Set RBW to 100KHz and VBM to 300KHz to measure the peak field strength and setRBW to 1MHz and VBW to 10Hz to measure the average radiated field strength.The conducted RF band edge was measured by using a spectrum analyzer. Set span wide enough to capture the highest in-band emission and the emission at the band edge. Set RBW to 100 KHz and VBW to 300 KHz,to measure the conducted peak band edge. 5.3 Test Result PASS Radiated Band Edge Test: Operation Mode: TX CH Low (2402MHz) Horizontal: Meter Emission Frequency Factor Limits Margin Detector Reading Level Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 2310 55.13 -5.81 49.32 74 -24.68 peak 2310 / -5.81 / 54 / AVG 2390 56.35 -5.84 50.51 74 -23.49 peak 2390 / -5.84 / 54 / AVG 2400 57.12 -5.84 51.28 74 -22.72 peak 2400 / -5.84 / 54 / AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Vertical: Meter Emission Frequency Factor Limits Margin Detector Reading Level Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 2310 55.39 -5.81 49.58 74 -24.42 peak 2310 / -5.81 / 54 / AVG 2390 55.27 -5.84 49.43 74 -24.57 peak 2390 / -5.84 / 54 / AVG 2400 56.34 -5.84 50.5 74 -23.5 peak 2400 / -5.84 / 54 / AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier.

Page 19 of 24Report No.:UNIA201812060405FR-01 Operation Mode: TX CH High (2480MHz) Horizontal: Meter Emission Detector Frequency Factor Limits Margin Reading Level Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 2483.5 57.11 -5.65 51.46 74 -22.42 peak 2483.5 / -5.65 / 54 / AVG 2500 56.39 -5.72 50.67 74 -20.42 peak 2500 / -5.72 / 54 / AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier. Vertical: Meter Emission Frequency Factor Limits Margin Detector Reading Level Type (MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) 2483.5 56.39 -5.65 50.74 74 -23.26 peak 2483.5 / -5.65 / 54 / AVG 2500 56.66 -5.72 50.94 74 -23.06 peak 2500 / -5.72 / 54 / AVG Remark: Factor = Antenna Factor + Cable Loss – Pre-amplifier.

Page 20 of 24Report No.:UNIA201812060405FR-01 6 OCCUPIED BANDWIDTH MEASUREMENT 6.1 Test Setup Same asRadiated Emission Measurement 6.2 Test Procedure 1. The EUT was placed on a turn table which is 0.8m above ground plane. 2. Set EUT as normal operation. 3. Based on ANSI C63.10 section 6.9.2: RBW=30KHz. VBW=100KHz, Span=3MHz. 4. The useful radiated emission from the EUT was detected by the spectrum analyzer with peak detector. 6.3 Measurement Equipment Used Same asRadiated Emission Measurement 6.4 Test Result PASS Frequency 20dB Bandwidth Result (MHz) (MHz) 2402 1.130 PASS 2440 1.130 PASS 2480 1.128 PASS CH: 2402MHz

Page 21 of 24Report No.:UNIA201812060405FR-01 CH: 2440MHz CH: 2480MHz

Page 22 of 24Report No.:UNIA201812060405FR-01 7 ANTENNA REQUIREMENT Standard Applicable: For intentional device, according to FCC 47 CFR Section 15.203, an intentional radiator shall be designed toensure that no antenna other than that furnished by the responsible party shall be used with the device. Antenna Connected Construction The antenna used in this product is anInternal Antenna, The directional gains of antenna used for transmitting is 0dBi. ANTENNA:

Page 23 of 24Report No.:UNIA201812060405FR-01 8 PHOTOGRAPH OF TEST 8.1 Radiated Emission

Page 24 of 24Report No.:UNIA201812060405FR-01 8.2Conducted Emission ***End of Report***


Document Created: 2018-12-19 14:05:58
Document Modified: 2018-12-19 14:05:58
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC