18_CA099A RFExp

FCC ID: 2AMH2-CA099A

RF Exposure Info

Download: PDF
FCCID_3963741

Page 1 of 28 FCC Test Report Report No.: AGC00737180729FE01 FCC ID : 2AMH2-CA099A APPLICATION PURPOSE : Original Equipment PRODUCT DESIGNATION : Wireless Charger Car Mount BRAND NAME : MPOW MODEL NAME : CA099A CLIENT : MPOW TECHNOLOGY CO., LIMITED DATE OF ISSUE : Jul. 31, 2018 STANDARD(S) : FCC Part 15 Rules TEST PROCEDURE(S) REPORT VERSION : V1.0 Attestation of Global Compliance (Shenzhen) Co., Ltd CAUTION: This report shall not be reproduced except in full without the written permission of the test laboratory and shall not be quoted out of context.

Report No.: AGC00737180729FE01 Page 2 of 28 REPORT REVISE RECORD Report Version Revise Time Issued Date Valid Version Notes V1.0 / Jul. 31, 2018 Valid Initial Release

Report No.: AGC00737180729FE01 Page 3 of 28 TABLE OF CONTENTS 1. VERIFICATION OF CONFORMITY .......................................................................................................................... 4 2. GENERAL INFORMATION ....................................................................................................................................... 5 2.1. PRODUCT DESCRIPTION ................................................................................................................................ 5 3. MEASUREMENT UNCERTAINTY ............................................................................................................................ 6 4. DESCRIPTION OF TEST MODES ............................................................................................................................ 7 5. SYSTEM TEST CONFIGURATION........................................................................................................................... 8 5.1. CONFIGURATION OF EUT SYSTEM ................................................................................................................ 8 5.2. EQUIPMENT USED IN EUT SYSTEM ............................................................................................................... 8 5.3. SUMMARY OF TEST RESULTS ........................................................................................................................ 8 6. TEST FACILITY ......................................................................................................................................................... 9 7. RADIATED EMISSION ............................................................................................................................................ 10 7.1TEST LIMIT ........................................................................................................................................................ 10 7.2. MEASUREMENT PROCEDURE ...................................................................................................................... 11 7.3. TEST SETUP .................................................................................................................................................... 12 7.4. TEST RESULT .................................................................................................................................................. 13 8. 20DB BANDWIDTH ................................................................................................................................................ 16 8.1. MEASUREMENT PROCEDURE ...................................................................................................................... 16 8.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ............................................................................. 16 8.3. MEASUREMENT RESULTS ............................................................................................................................ 17 9. FCC LINE CONDUCTED EMISSION TEST ........................................................................................................... 18 9.1. LIMITS OF LINE CONDUCTED EMISSION TEST ........................................................................................... 18 9.2. BLOCK DIAGRAM OF LINE CONDUCTED EMISSION TEST ......................................................................... 18 9.3. PRELIMINARY PROCEDURE OF LINE CONDUCTED EMISSION TEST ...................................................... 19 9.4. FINAL PROCEDURE OF LINE CONDUCTED EMISSION TEST..................................................................... 19 9.5. TEST RESULT OF LINE CONDUCTED EMISSION TEST ............................................................................... 20 APPENDIX A: PHOTOGRAPHS OF TEST SETUP ................................................................................................... 21 APPENDIX B: PHOTOGRAPHS OF EUT .................................................................................................................. 22

Report No.: AGC00737180729FE01 Page 4 of 28 1. VERIFICATION OF CONFORMITY Applicant MPOW TECHNOLOGY CO., LIMITED RM 603, 6/F, HANG PONT COMM BLDG 31 TONKIN ST, CHEUNG SHA WAN Address KL, HK,CHINA Manufacturer MPOW TECHNOLOGY CO., LIMITED RM 603, 6/F, HANG PONT COMM BLDG 31 TONKIN ST, CHEUNG SHA WAN Address KL, HK,CHINA Product Designation Wireless Charger Car Mount Brand Name MPOW Test Model CA099A Date of test Jul. 25, 2018 to Jul. 31, 2018 Deviation None Condition of Test Sample Normal Test Result Pass We hereby certify that: The above equipment was tested by Attestation of Global Compliance (Shenzhen) Co., Ltd. The test data, data evaluation, test procedures, and equipment configurations shown in this report were made in accordance with the procedures given in ANSI C63.10 (2013) and the energy emitted by the sample EUT tested as described in this report is in compliance with Section 15.207, 15.209, 15.203 of the FCC Part 15, Subpart C Rules. The results of testing in this report apply to the product/system which was tested only. Tested By Steven Zhou(Zhou Pengyun) Jul. 31, 2018 Reviewed By Bart Xie(Xie Xiaobin) Jul. 31, 2018 Approved By Forrest Lei(Lei Yonggang) Jul. 31, 2018 Authorized Officer

Report No.: AGC00737180729FE01 Page 5 of 28 2. GENERAL INFORMATION 2.1. PRODUCT DESCRIPTION A major technical description of EUT is described as following Operation Frequency 146.4KHz Maximum field strength 53.55dBuV/m(Peak)@3m Number of channels 1 Antenna Designation Integrated Antenna (Met 15.203 Antenna requirement) Hardware Version CA099A_V0.2 Software Version V1.0 Power Supply DC5V

Report No.: AGC00737180729FE01 Page 6 of 28 3. MEASUREMENT UNCERTAINTY The uncertainty is calculated using the methods suggested in the “Guide to the Expression of Uncertainty in measurement” (GUM) published by CISPR and ANSI. - Uncertainty of Conducted Emission, Uc = ±3.2 dB - Uncertainty of Radiated Emission below 1GHz, Uc = ±3.9 dB - Uncertainty of Radiated Emission above 1GHz, Uc = ±4.8 dB

Report No.: AGC00737180729FE01 Page 7 of 28 4. DESCRIPTION OF TEST MODES NO. TEST MODE DESCRIPTION 1 Wireless charging Mode(Full load) 2 Wireless charging Mode(half load) 3 Wireless charging Mode(Null load) Note: 1. The mode 1 was the worst case and only the data of the worst case record in this report.

Report No.: AGC00737180729FE01 Page 8 of 28 5. SYSTEM TEST CONFIGURATION 5.1. CONFIGURATION OF EUT SYSTEM Configure : EUT Accessory 5.2. EQUIPMENT USED IN EUT SYSTEM Item Equipment Model No. ID or Specification Remark 1 Wireless Charger CA099A 2AMH2-CA099A EUT Wireless electronic 2 -- Maximum power 10W Support Load 5.3. SUMMARY OF TEST RESULTS FCC RULES DESCRIPTION OF TEST RESULT §15.209 Radiated Emission Compliant §15.215 20dB bandwidth Compliant §15.207 Conducted Emission Compliant

Report No.: AGC00737180729FE01 Page 9 of 28 6. TEST FACILITY Test Site Attestation of Global Compliance (Shenzhen) Co., Ltd 1-2F., Bldg.2, No.1-4, Chaxi Sanwei Technical Industrial Park, Gushu, Xixiang, Location Bao’an District B112-B113, Bldg.12, Baoan Bldg Materials Center, No.1 of Xixiang Inner Ring Road, Baoan District, Shenzhen 518012 NVLAP LAB CODE 600153-0 Designation Number CN5028 FCC Test Firm 682566 Registration Number Attestation of Global Compliance(Shenzhen) Co., Ltd is accredited by National Description Voluntary Laboratory Accreditation program, NVLAP Code 600153-0 TEST EQUIPMENT OF RADIATED EMISSION TEST Equipment Manufacturer Model S/N Cal. Date Cal. Due TEST RECEIVER R&S ESCI 10096 Jun.12, 2018 Jun.11, 2019 EXA Signal Aglient N9010A MY53470504 Dec.08, 2017 Dec.07, 2018 Analyzer preamplifier ChengYi EMC184045SE 980508 Sep.15, 2017 Sep.14, 2018 Loop Antenna A.H.Systems,Inc SAS-562B -- Feb. 27, 2018 Feb. 26, 2019 Broadband SCHWARZBECK BBV 9718 9718-205 Jun.12, 2018 Jun.11, 2019 Preamplifier ANTENNA SCHWARZBECK VULB9168 D69250 Sep.28, 2017 Sep.27, 2018 TEST EQUIPMENT OF CONDUCTED EMISSION TEST Equipment Manufacturer Model S/N Cal. Date Cal. Due TEST RECEIVER R&S ESPI 101206 Jun.12, 2018 Jun.11, 2019 LISN R&S ESH2-Z5 100086 Aug.21, 2017 Aug.20, 2018

AG °s — x m Attestation of Global Compliance Report No.: AGC00737180729FEO1 Page 10 of 28 7. RADIATED EMISSION 7.A1TEST LIMIT Standard FCC 15.209 Frequency Distance Field Strengths Limit (MHz) Meters u V/m dB(pV)/m 0.009 ~ 0.490 300 2400/F (KHz) 0.490 ~ 1.705 30 24000/F(kHz) 1.705 ~ 30 30 30 30 ~ 88 3 100 40.0 88 ~ 216 3 150 43.5 216 ~ 960 3 200 46.0 960 ~ 1000 3 500 54.0 Above 1000 3 Other:74.0 dB(uV)/m (Peak) 54.0 dB(uV)/m (Average) Remark: (1) Emission level dBu V = 20 log Emission level u V/m (2) The smaller limit shall apply at the cross point between two frequency bands. (3) Distance is the distance in meters between the measuring instrument, antenna and the closest point of any part of the device or system. The results ’m,6tison| o thisfeaost report refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued by/A C§€ this docu/m it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed tfittp://www.agc-«& t.com. o Attestatic >ginpliance Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@agc—cert.com @ 400 089 2118 Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

Report No.: AGC00737180729FE01 Page 11 of 28 7.2. MEASUREMENT PROCEDURE 1. The EUT was placed on the top of the turntable 0.8 or 1.5 meter above ground. The phase center of the receiving antenna mounted on the top of a height-variable antenna tower was placed 3 meters far away from the turntable. 2. Power on the EUT and all the supporting units. The turntable was rotated by 360 degrees to determine the position of the highest radiation. 3. The height of the broadband receiving antenna was varied between one meter and four meters above ground to find the maximum emissions field strength of both horizontal and vertical polarization. 4. For each suspected emissions, the antenna tower was scan (from 1 M to 4 M) and then the turntable was rotated (from 0 degree to 360 degrees) to find the maximum reading. 5. Set the test-receiver system to Peak or CISPR quasi-peak Detect Function with specified bandwidth under Maximum Hold Mode. 6. In case the emission is lower than 30MHz, loop antenna has to be used for measurement and the recorded data should be QP measured by receiver. High - Low scan is not required in this case. The following table is the setting of spectrum analyzer and receiver. Spectrum Parameter Setting Start ~Stop Frequency 9KHz~150KHz/RB 200Hz for QP Start ~Stop Frequency 150KHz~30MHz/RB 9KHz for QP Start ~Stop Frequency 30MHz~1000MHz/RB 120KHz for QP Receiver Parameter Setting Start ~Stop Frequency 9KHz~150KHz/RB 200Hz for QP Start ~Stop Frequency 150KHz~30MHz/RB 9KHz for QP Start ~Stop Frequency 30MHz~1000MHz/RB 120KHz for QP

Report No.: AGC00737180729FE01 Page 12 of 28 7.3. TEST SETUP Radiated Emission Test-Setup Frequency Below 30MHz RADIATED EMISSION TEST SETUP 30MHz-1000MHz

Report No.: AGC00737180729FE01 Page 13 of 28 7.4. TEST RESULT RADIATED EMISSION BELOW 30MHZ Factor Level Limit Frequency Reading Margin Polarization dB dB(uV/m) dB(uV/m) Pass/Fail MHz dB(uV) dB (1/m) Peak Average 0.1464 Face 43.15 10.4 53.55 104.64 51.09 Pass 0.1464 Side 38.39 10.4 48.79 104.64 55.85 Pass Note: No other emissions found between lowest internal used/generated frequencies to 30MHz. The peak level of the emission is less than the average limit, so the average level shall be less than the limit without test.

® A\G # 7 H 1 i * * Attestation of Global Compliance Report No.: AGC00737180729FEO01 Page 14 of 28 RADIATED EMISSION 30MHz— 1GHZ EUT : Wireless Charger Model Name. : CAO9g9A Temperature : 20 °C Relative Humidtity: [48% Pressure : 1010 hPa Test Voltage : Normal Test Mode : Mode 1 Polarization : Horizontal 66.9 dBuy/m Limat: — Marginc a== 27 4 f 2 13 30.000 127.00 224.00 321.00 418.00 515.00 G12.00 709.00 05. O0 1000.00 MH=z 20. Antenna| Table Freq. Readi Factor |Measurement| Limit Ov T No. |MKk] E9 ng| ra SV *‘ petector |_Height Degree Comment MHz dBu dBim dBuVim dBu\im d em degree i > 42923 #»119 117 3290 |40.00 —7.10| peak 3 ar.9000 isi7 838 2255 |43.50 |—19.95| peak 3 1299233 918 1517 3435 |43.50 |—19.15| peak 4 i9i.s66r a67 1181 2128 4350 |—2222| peak 5 2951333 913 1458 7371 |46.00 |—22.29| peak 6 500.4500 022 21 14 2136 46.00 |24.64) peak RESULT: PASS The results "V«Sticor| o thisfesost report refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued by/A C§€ this docu’t& it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed tfittp://www.agc-% t.com. o Attestatic o pliance Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@agc—cert.com @ 400 089 2118 iN¥ Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

® A\G # 7 H 1 i * * Attestation of Global Compliance Report No.: AGC00737180729FEO01 Page 15 of 28 EUT : Wireless Charger Model Name. : CAO9g9A Temperature : 20 C Relative Humidtity : (48% Pressure : 1010 hPa Test Voltage : Normal Test Mode : Mode 1 Polarization : Vertical 66.9 dBu¥/m Limak: === Manginc _ 30.000 127.00 224.00 32700 418.00 515.00 G12.00 209.00 06. O0 1000.00 MHz \|Mik] Frea |Reading] Factor |Measurement| Limit Over Daemwflrl?m Comment MHz dBuW dBim dBu\im dBuvim| 4B om degree 1 429333 2344 871 3215 |40.00 |—7.85| peak 2 sesess 1600 416 2016 40.00 |—19.84| peak 3| * 1480167 2164 1525 3689 |43.50 661| peak 4 i9i.66e7 &9 1111 20.02 |43.50 |—23.48| peak 5 2434000 820 13225 2145 |46.00 —24.55| peak 6 2951333 1146 1526 2672 |46.00 |—19.28| peak RESULT: PASS Note: Factor=Antenna Factor + Cable loss, Margin=Result—Limit. The "Factor" value can be calculated automatically by software of measurement system. The results "V«Sticor| o thisfesost report refer only to the sample(s) tested unless otherwise stated and the sample(s) are retained for 30 days only. The document is issued by/A C§€ this docu’t& it cannot be reproduced except in full with our prior written permission. The more details and the authenticity of the report will be confirmed tfittp://www.agc-% t.com. o Attestatic o pliance Tel: +86—755 2908 1955 Fax: +86—755 2600 8484 E—mail: agc@agc—cert.com @ 400 089 2118 iN¥ Add: 2/F. , Building 2, No.1—4, Chaxi Sanwei Technical Industrial Park,Gushu, Xixiang, Bacan District, Shenzhen, Guangdong China

Report No.: AGC00737180729FE01 Page 16 of 28 8. 20DB BANDWIDTH 8.1. MEASUREMENT PROCEDURE 1. The EUT was placed on the top of the turntable 0.8 meter above ground. The phase center of the receiving antenna mounted on the top of a height-variable antenna tower was placed 3 meters far away from the turntable. 2, Set the EUT Work on operation frequency. 3. Set Span = approximately 2 to 5 times the 20 dB bandwidth, centered on a channel The nominal IF filter bandwidth (3 dB RBW) shall be in the range of 1% to 5% of the OBW and video bandwidth (VBW) shall be approximately three times RBW; Sweep = auto; Detector function = peak 4. Set SPA Trace 1 Max hold, then View. 8.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION)

Report No.: AGC00737180729FE01 Page 17 of 28 8.3. MEASUREMENT RESULTS TEST ITEM 20DB BANDWIDTH TEST MODULATION FSK Frequency (KHz) Test Data (Hz) Criteria 146.4 555 PASS TEST PLOT OF BANDWIDTH

Report No.: AGC00737180729FE01 Page 18 of 28 9. FCC LINE CONDUCTED EMISSION TEST 9.1. LIMITS OF LINE CONDUCTED EMISSION TEST Maximum RF Line Voltage Frequency Q.P.( dBuV) Average( dBuV) 150kHz~500kHz 66-56 56-46 500kHz~5MHz 56 46 5MHz~30MHz 60 50 Note: 1. The lower limit shall apply at the transition frequency. 2. The limit decreases linearly with the logarithm of the frequency in the range 0.15 MHz to 0.50MHz. 9.2. BLOCK DIAGRAM OF LINE CONDUCTED EMISSION TEST EUT & Support Units

Report No.: AGC00737180729FE01 Page 19 of 28 9.3. PRELIMINARY PROCEDURE OF LINE CONDUCTED EMISSION TEST 1. The equipment was set up as per the test configuration to simulate typical actual usage per the user’s manual. When the EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and is placed on the ground plane as per ANSI C63.10 (see Test Facility for the dimensions of the ground plane used). When the EUT is a floor-standing equipment, it is placed on the ground plane which has a 3-12 mm non-conductive covering to insulate the EUT from the ground plane. 2. Support equipment, if needed, was placed as per ANSI C63.10. 3. All I/O cables were positioned to simulate typical actual usage as per ANSI C63.10. 4. All support equipments received AC120V/60Hz power from a LISN, if any. 5. The EUT received charging voltage by adapter which received 120V/60Hzpower by a LISN.. 6. The test program was started. Emissions were measured on each current carrying line of the EUT using a spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two monitoring points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1 connected to Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line 1 connected to a 50 ohm load and Line 2 connected to the Analyzer / Receiver. 7. Analyzer / Receiver scanned from 150 kHz to 30MHz for emissions in each of the test modes. 8. During the above scans, the emissions were maximized by cable manipulation. 9. The test mode(s) were scanned during the preliminary test. Then, the EUT configuration and cable configuration of the above highest emission level were recorded for reference of final testing. 9.4. FINAL PROCEDURE OF LINE CONDUCTED EMISSION TEST 1. EUT and support equipment was set up on the test bench as per step 2 of the preliminary test. 2. A scan was taken on both power lines, Line 1 and Line 2, recording at least the six highest emissions. Emission frequency and amplitude were recorded into a computer in which correction factors were used to calculate the emission level and compare reading to the applicable limit. If EUT emission level was less –2dB to the A.V. limit in Peak mode, then the emission signal was re-checked using Q.P and Average detector. 3. The test data of the worst case condition(s) was reported on the Summary Data page.

Report No.: AGC00737180729FE01 Page 20 of 28 9.5. TEST RESULT OF LINE CONDUCTED EMISSION TEST N/A

Report No.: AGC00737180729FE01 Page 21 of 28 APPENDIX A: PHOTOGRAPHS OF TEST SETUP FCC RADIATED EMISSION TEST SETUP 9kHz-30MHz FCC RADIATED EMISSION TEST SETUP 30MHz-1000MHz

Report No.: AGC00737180729FE01 Page 22 of 28 APPENDIX B: PHOTOGRAPHS OF EUT ALL VIEW OF EUT TOP VIEW OF EUT

Report No.: AGC00737180729FE01 Page 23 of 28 BOTTOM VIEW OF EUT FRONT VIEW OF EUT

Report No.: AGC00737180729FE01 Page 24 of 28 BACK VIEW OF EUT LEFT VIEW OF EUT

Report No.: AGC00737180729FE01 Page 25 of 28 RIGHT VIEW OF EUT OPEN VIEW-1 OF EUT

Report No.: AGC00737180729FE01 Page 26 of 28 INTERNAL VIEW-1 OF EUT INTERNAL VIEW-2 OF EUT

Report No.: AGC00737180729FE01 Page 27 of 28 INTERNAL VIEW-3 OF EUT INTERNAL VIEW-4 OF EUT

Report No.: AGC00737180729FE01 Page 28 of 28 INTERNAL VIEW-5 OF EUT ----END OF REPORT----


Document Created: 2018-08-13 14:47:47
Document Modified: 2018-08-13 14:47:47
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC