14_Chameleon TestRpt DTS-BLE

FCC ID: 2AM8GCHAMELEON

Test Report

Download: PDF

FCCID_3524985

Report No.: AGC10576170701FE08
Page 2 of 34

Report Revise Record

Report Version Revise Time Issued Date Valid Version Notes

V1.0 / July 12, 2017 Valid Original Report

Report No.: AGC10576170701FE08
Page 3 of 34

TABLE OF CONTENTS

1. VERIFICATION OF COMPLIANCE ...................................................................................................... 5
2.GENERAL INFORMATION ................................................................................................................... 6
2.1PRODUCT DESCRIPTION............................................................................................................. 6
2.2 RELATED SUBMITTAL(S)/GRANT(S) .......................................................................................... 6
2.3TEST METHODOLOGY ................................................................................................................. 6
2.4 TEST FACILITY ............................................................................................................................. 6
2.5 SPECIAL ACCESSORIES ............................................................................................................. 6
2.6 EQUIPMENT MODIFICATIONS .................................................................................................... 6
3. SYSTEM TEST CONFIGURATION ...................................................................................................... 7
3.1 CONFIGURATION OF TESTED SYSTEM ..................................................................................... 7
3.2 EQUIPMENT USED IN TESTED SYSTEM .................................................................................... 7
4. SUMMARY OF TEST RESULTS ........................................................................................................ 10
5. DESCRIPTION OF TEST MODES ..................................................................................................... 10
6. ANTENNA REQUIREMENT..............................................................................................................11
6.1. STANDARD APPLICABLE .......................................................................................................... 11
6.2. TEST RESULT ............................................................................................................................ 11
7. RADIATED EMISSION ....................................................................................................................... 12
7.1 MEASUREMENT PROCEDURE ................................................................................................. 12
7.2 TEST SETUP .............................................................................................................................. 13
7.3 LIMITS AND MEASUREMENT RESULT ..................................................................................... 14
7.4 TEST RESULT ............................................................................................................................ 14
8. BAND EDGE EMISSION .................................................................................................................... 18
8.1. MEASUREMENT PROCEDURE ................................................................................................ 18
8.2. TEST SET-UP ............................................................................................................................ 18
8.3. RADIATED TEST RESULT ............................................................................................................... 19
8.4. CONDUCTED TEST RESULT ........................................................................................................... 20
9. 6DB BANDWIDTH ............................................................................................................................. 21
9.1. TEST PROCEDURE ................................................................................................................... 21
9.2. SUMMARY OF TEST RESULTS/PLOTS .................................................................................... 21
10. CONDUCTED OUTPUT POWER ..................................................................................................... 22
10.1. MEASUREMENT PROCEDURE .............................................................................................. 22
10.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ...................................................... 22
10.3. LIMITS AND MEASUREMENT RESULT................................................................................... 22
11. MAXIMUM CONDUCTED OUTPUT POWER SPECTRAL DENSITY ............................................... 24
11.1 MEASUREMENT PROCEDURE ............................................................................................... 24
11.2 TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION) ....................................................... 24

Report No.: AGC10576170701FE08
Page 4 of 34

11.3 LIMITS AND MEASUREMENT RESULT.................................................................................... 24
12. FCC LINE CONDUCTED EMISSION TEST ..................................................................................... 24
12.1 LIMITS ....................................................................................................................................... 26
12.2 TEST SETUP............................................................................................................................. 26
12.3 PRELIMINARY PROCEDURE ................................................................................................... 27
12.4 FINAL TEST PROCEDURE ....................................................................................................... 27
12.5 TEST RESULT OF POWER LINE .............................................................................................. 28
13. CONDUCTED SPURIOUS EMISSION ............................................................................................. 30
13.1. MEASUREMENT PROCEDURE .............................................................................................. 30
13.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION)....................................................... 30
13.3. MEASUREMENT EQUIPMENT USED ..................................................................................... 30
13.4. LIMITS AND MEASUREMENT RESULT ................................................................................... 30
APPENDIX A: PHOTOGRAPHS OF TEST SETUP ............................................................................... 33

Report No.: AGC10576170701FE08
Page 6 of 34

2.GENERAL INFORMATION
2.1PRODUCT DESCRIPTION
The EUT is designed as “IP54 - IP 67 Rugged Handheld, Desktop & Tablet Device”. It is designed by way of
utilizing the FHSS technology to achieve the system operation.

A major technical description of EUT is described as following

Operation Frequency 2.402 GHz to 2.480GHz

Bluetooth Version V4.0

Modulation GFSK
Number of channels 40 Channel(37 Hopping Channel,3 advertising Channel)
Antenna Designation PIFA Antenna
Antenna Gain 0.7dBi
Hardware Version V1.3
Software Version V1.3
Power Supply DC3.7V by Built-in Li-ion Battery

2.2 RELATED SUBMITTAL(S)/GRANT(S)
This submittal(s) (test report) is intended for FCC ID: 2AM8GCHAMELEON filing to comply with Section
15.247of the FCC Part 15, Subpart C Rules.

2.3TEST METHODOLOGY
All measurements contained in this report were conducted with KDB 558074, American National Standard for
Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electronic Equipment in
the range of 9 kHz to 40 GHz.
The equipment under test (EUT) was configured to measure its highest possible emission level. The test
modes were adapted accordingly in reference to the Operating Instructions. The EUT was tested in all three
orthogonal planes and the worse case was showed.

2.4 TEST FACILITY
Site Dongguan Precise Testing Service Co., Ltd.
Building D,Baoding Technology Park,Guangming Road2,Dongcheng District,
Location
Dongguan, Guangdong, China,
FCC Registration No. 371540
The test site is constructed and calibrated to meet the FCC requirements in
Description
documents ANSI C63.10:2013.

2.5 SPECIAL ACCESSORIES
Refer to section 2.2.

2.6 EQUIPMENT MODIFICATIONS
Not available for this EUT intended for grant.

Report No.: AGC10576170701FE08
Page 7 of 34

3. SYSTEM TEST CONFIGURATION

3.1 CONFIGURATION OF TESTED SYSTEM

Configuration:

EUT Accessory

3.2 EQUIPMENT USED IN TESTED SYSTEM

Item Equipment Model No. ID or Specification Remark
IP54 - IP 67 Rugged Handheld,
1 Chameleon FCC ID: 2AM8GCHAMELEON EUT
Desktop & Tablet Devices

2 Adapter BYX-0505000M DC 5.0V/5A Accessory

3 Battery 4890108P-1S2P DC3.7V/ 13000mAh Accessory
4 USB Cable N/A N/A Accessory

ALL TEST EQUIPMENT LIST
FOR RADIATED EMISSION TEST (BELOW 1GHZ)
Radiated Emission Test Site
Serial Last Due
Name of Equipment Manufacturer Model Number
Number Calibration Calibration
EMI Test Receiver Rohde & Schwarz ESCI 101417 July 3, 2016 July 2, 2017
EMI Test Receiver Rohde & Schwarz ESCI 101417 July 2, 2017 July 1, 2018
Trilog Broadband
SCHWARZBECK VULB9160 9160-3355 July 3, 2016 July 2, 2017
Antenna (25M-1GHz)
Trilog Broadband
SCHWARZBECK VULB9160 9160-3355 July 2, 2017 July 1, 2018
Antenna (25M-1GHz)
Signal Amplifier SCHWARZBECK BBV 9475 9745-0013 July 3, 2016 July 2, 2017
Signal Amplifier SCHWARZBECK BBV 9475 9745-0013 July 2, 2017 July 1, 2018
RF Cable SCHWARZBECK AK9515E 96221 July 3, 2016 July 2, 2017
RF Cable SCHWARZBECK AK9515E 96221 July 2, 2017 July 1, 2018
3m Anechoic Chamber CHENGYU 966 PTS-001 June 2, 2017 June 1, 2018
MULTI-DEVICE
Max-Full MF-7802 MF780208339 N/A N/A
Positioning Controller
Active loop antenna Schwarzbeck FMZB1519 1519-038 June 5, 2016 June 4, 2018

Report No.: AGC10576170701FE08
Page 8 of 34

(9K-30MHz)

Spectrum analyzer Agilent E4407B MY46185649 June 2, 2017 June 1, 2018

Power Probe R&S NRP-Z23 100323 July 24,2016 July 23,2017

RF attenuator N/A RFA20db 68 N/A N/A

FOR RADIATED EMISSION TEST (1GHZ ABOVE)
Radiated Emission Test Site
Serial Last Due
Name of Equipment Manufacturer Model Number
Number Calibration Calibration
EMI Test Receiver Rohde & Schwarz ESCI 101417 July 3, 2016 July 2, 2017

EMI Test Receiver Rohde & Schwarz ESCI 101417 July 2, 2017 July 1, 2018
Horn Antenna
SCHWARZBECK BBHA9120D 9120D-1246 July 10, 2016 July 9, 2018
(1G-18GHz)
Spectrum Analyzer Agilent E4411B MY4511453 July 3, 2016 July 2, 2017
Spectrum Analyzer Agilent E4411B MY4511453 July 2, 2017 July 1, 2018
Signal Amplifier SCHWARZBECK BBV 9718 9718-269 July 6, 2016 July 5, 2017
Signal Amplifier SCHWARZBECK BBV 9718 9718-269 July 2, 2017 July 1, 2018
RF Cable SCHWARZBECK AK9515H 96220 July 7, 2016 July 6, 2017
RF Cable SCHWARZBECK AK9515H 96220 July 2, 2017 July 1, 2018
3m Anechoic Chamber CHENGYU 966 PTS-001 June 2, 2017 June 1, 2018
MULTI-DEVICE
Max-Full MF-7802 MF780208339 N/A N/A
Positioning Controller
Horn Ant (18G-40GHz) Schwarzbeck BBHA 9170 9170-181 June 5, 2016 June 4, 2018

Power Probe R&S NRP-Z23 100323 July 24,2016 July 23,2017

RF attenuator N/A RFA20db 68 N/A N/A

Conducted Emission Test Site
Name of Last
Manufacturer Model Number Serial Number Due Calibration
Equipment Calibration
EMI Test Receiver Rohde & Schwarz ESCI 101417 July 3, 2016 July 2, 2017
EMI Test Receiver Rohde & Schwarz ESCI 101417 July 2, 2017 July 1, 2018
Artificial Mains
Narda L2-16B 000WX31025 July 7, 2016 July 6, 2017
Network
Artificial Mains
Narda L2-16B 000WX31025 July 2, 2017 July 1, 2018
Network
Artificial Mains
Narda L2-16B 000WX31026 July 7, 2016 July 6, 2017
Network (AUX)
Artificial Mains Narda L2-16B 000WX31026 July 2, 2017 July 1, 2018

Report No.: AGC10576170701FE08
Page 9 of 34

Network (AUX)
RF Cable SCHWARZBECK AK9515E 96222 July 3, 2016 July 2, 2017
RF Cable SCHWARZBECK AK9515E 96222 July 2, 2017 July 1, 2018
Shielded Room CHENGYU 843 PTS-002 June 2,2017 June 1,2018

Conducted Emission Test Site
Name of Last
Manufacturer Model Number Serial Number Due Calibration
Equipment Calibration
EMI Test Receiver Rohde & Schwarz ESCI 101417 July 3, 2016 July 2, 2017
EMI Test Receiver Rohde & Schwarz ESCI 101417 July 2, 2017 July 1, 2018
Artificial Mains
Narda L2-16B 000WX31025 July 7, 2016 July 6, 2017
Network
Artificial Mains
Narda L2-16B 000WX31025 July 2, 2017 July 1, 2018
Network
Artificial Mains
Narda L2-16B 000WX31026 July 7, 2016 July 6, 2017
Network (AUX)
Artificial Mains
Narda L2-16B 000WX31026 July 2, 2017 July 1, 2018
Network (AUX)
RF Cable SCHWARZBECK AK9515E 96222 July 3, 2016 July 2, 2017
RF Cable SCHWARZBECK AK9515E 96222 July 2, 2017 July 1, 2018
Shielded Room CHENGYU 843 PTS-002 June 2,2017 June 1,2018

Report No.: AGC10576170701FE08
Page 10 of 34

4. SUMMARY OF TEST RESULTS

FCC RULES DESCRIPTION OF TEST RESULT
§15.203 Antenna Requirement Compliant
§15.209
Radiated Emission Compliant
§15.247(d)
§15.247(d) Band Edges Compliant
§15.247 6 dB Bandwidth Compliant
§15.247(b) Conducted Power Compliant
§15.247(e) Maximum Conducted Output Power SPECTRAL Density Compliant
§15.207 Line Conduction Emission Compliant

§15.207 Conduction Emission Compliant

5. DESCRIPTION OF TEST MODES

The EUT has been operated in three modulations: GFSK independently.
NO. TEST MODE DESCRIPTION
1 Low channel TX
2 Middle channel TX
3 High channel TX
4 Normal Operating (BT)
Note:
1. All the test modes can be supply by Built-in Li-ion battery, only the result of the worst case was recorded in
the report if no any records.
2. For Radiated Emission, 3axis were chosen for testing for each applicable mode.
3. Eut is operating at its maximum duty cycle>or equal 98%

Report No.: AGC10576170701FE08
Page 11 of 34

6. ANTENNA REQUIREMENT
6.1. STANDARD APPLICABLE

According to FCC 15.203, An intentional radiator shall be designed to ensure that no antenna other than that
furnished by the responsible party shall be used with the device. The use of a permanently attached antenna
or of an antenna that uses a unique coupling to the intentional radiator shall be considered sufficient to comply
with the provisions of this Section. The manufacturer may design the unit so that a broken antenna can be
replaced by the user, but the use of a standard antenna jack or electrical connector is prohibited. This
requirement does not apply to carrier current devices or to devices operated under the provisions of Sections
15.211, 15.213, 15.217, 15.219, or 15.221. Further, this requirement does not apply to intentional radiators
that must be professionally installed, such as perimeter protection systems and some field disturbance sensors,
or to other intentional radiators which, in accordance with Section 15.31(d), must be measured at the
installation site. However, the installer shall be responsible for ensuring that the proper antenna is employed
so that the limits in this Part are not exceeded.

6.2. TEST RESULT

This product has a permanent antenna, fulfill the requirement of this section.

Report No.: AGC10576170701FE08
Page 12 of 34

7. RADIATED EMISSION
7.1 MEASUREMENT PROCEDURE
1. The EUT was placed on the top of the turntable 0.8 or 1.5 meter above ground. The phase center of the
receiving antenna mounted on the top of a height-variable antenna tower was placed 3 meters far away
from the turntable.
2. Power on the EUT and all the supporting units. The turntable was rotated by 360 degrees to determine the
position of the highest radiation.
3. The height of the broadband receiving antenna was varied between one meter and four meters above
ground to find the maximum emissions field strength of both horizontal and vertical polarization.
4. For each suspected emissions, the antenna tower was scan (from 1 M to 4 M) and then the turntable was
rotated (from 0 degree to 360 degrees) to find the maximum reading.
5. Set the test-receiver system to Peak or CISPR quasi-peak Detect Function with specified bandwidth under
Maximum Hold Mode.
6. For emissions above 1GHz, use 1MHz VBW and RBW for peak reading. Then 1MHz RBW and 10Hz VBW
for average reading in spectrum analyzer. Place the measurement antenna away from each area of the
EUT determined to be a source of emissions at the specified measurement distance, while keeping the
measurement antenna aimed at the source of emissions at each frequency of significant emissions, with
polarization oriented for maximum response. The measurement antenna may have to be higher or lower
than the EUT, depending on the radiation pattern of the emission and staying aimed at the emission source
for receiving the maximum signal. The final measurement antenna elevation shall be that which maximizes
the emissions. The measurement antenna elevation for maximum emissions shall be restricted to a range
of heights of from 1 m to 4 m above the ground or reference ground plane.
7. When the radiated emissions limits are expressed in terms of the average value of the emissions, and
pulsed operation is employed, the measurement field strength shall be determined by averaging over one
complete pulse train, including blanking intervals, as long as the pulse train does not exceed 0.1 seconds.
As an alternative (provided the transmitter operates for longer than 0.1 seconds) or in cases where the
pulse train exceeds 0.1 seconds, the measured field strength shall be determined from the average
absolute voltage during a 0.1 second interval during which the field strength is at its maximum values.
8.If the emissions level of the EUT in peak mode was 3 dB lower than the average limit specified, then testing
will be stopped and peak values of EUT will be reported, otherwise, the emissions which do not have 3 dB
margin will be repeated one by one using the quasi-peak method for below 1GHz.
9. For testing above 1GHz, the emissions level of the EUT in peak mode was lower than average limit (that
means the emissions level in peak mode also complies with the limit in average mode), then testing will be
stopped and peak values of EUT will be reported, otherwise, the emissions will be measured in average
mode again and reported.
10. In case the emission is lower than 30MHz, loop antenna has to be used for measurement and the
recorded data should be QP measured by receiver. High - Low scan is not required in this case.

Report No.: AGC10576170701FE08
Page 14 of 34

7.3 LIMITS AND MEASUREMENT RESULT
15.209 Limit in the below table has to be followed
Frequencies Field Strength Measurement Distance
(MHz) (micorvolts/meter) (meters)
0.009~0.490 2400/F(KHz) 300
0.490~1.705 24000/F(KHz) 30
1.705~30.0 30 30
30~88 100 3
88~216 150 3
216~960 200 3
Above 960 500 3
Note: All modes were tested For restricted band radiated emission,
the test records reported below are the worst result compared to other modes.
7.4 TEST RESULT

RADIATED EMISSION BELOW 30MHZ
No emission found between lowest internal used/generated frequencies to 30MHz.

Report No.: AGC10576170701FE08
Page 17 of 34

RADIATED EMISSION ABOVE 1GHZ
Frequency Meter Reading Factor Emission Level Limits Margin Detector
Comment
(MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) Type
Low Channel (2402 MHz)
4804 39.87 10.44 50.31 74 -23.69 Pk Horizontal
4804 28.49 10.44 38.93 54 -15.07 AV Horizontal
7206 40.12 12.39 52.51 74 -21.49 pk Horizontal
7206 27.85 12.39 40.24 54 -13.76 AV Horizontal
4804 43.95 10.4 54.35 74 -19.65 Pk Vertical
4804 27.47 10.4 37.87 54 -16.13 AV Vertical
7206 39.70 12.75 52.45 74 -21.55 Pk Vertical
7206 27.09 12.75 39.84 54 -14.16 AV Vertical
Mid Channel (2440 MHz)
4880 40.66 10.4 51.06 74 -22.94 Pk Horizontal
4880 29.80 10.4 40.20 54 -13.80 AV Horizontal
7320 40.05 12.75 52.80 74 -21.20 Pk Horizontal
7320 29.57 12.75 42.32 54 -11.68 AV Horizontal
4880 42.80 10.39 53.19 74 -20.81 Pk Vertical
4880 27.96 10.44 38.40 54 -15.60 AV Vertical
7320 39.45 12.68 52.13 74 -21.87 Pk Vertical
7320 30.14 12.68 42.82 54 -11.18 AV Vertical
High Channel (2480 MHz)
4960 42.19 10.39 52.58 74 -21.42 pk Horizontal
4960 30.51 10.39 40.90 54 -13.10 AV Horizontal
7440 38.68 12.68 51.36 74 -22.64 pk Horizontal
7440 27.33 12.68 40.01 54 -13.99 AV Horizontal
4960 42.96 10.39 53.35 74 -20.65 pk Vertical
4960 29.32 10.39 39.71 54 -14.29 AV Vertical
7440 40.31 12.68 52.99 74 -21.01 pk Vertical
7440 29.31 12.68 41.99 54 -12.01 AV Vertical

RESULT: PASS

Note: 1~25GHz scan with GFSK. No recording in the test report at least have 20dB margin.
Factor = Antenna Factor + Cable Loss – Pre-amplifier.
Emission Level = Meter Reading + Factor
Margin = Emission - Leve Limit

Report No.: AGC10576170701FE08
Page 18 of 34

8. BAND EDGE EMISSION
8.1. MEASUREMENT PROCEDURE
1)Radiated restricted band edge measurements
The radiated restricted band edge measurements are measured with an EMI test receiver connected to the
receive antenna while the EUT is transmitting
2)Conducted Emissions at the bang edge
a)The transmitter output was connected to the spectrum analyzer
b)Set RBW=100kHz,VBW=300kHz
c)Suitable frequency span including 100kHz bandwidth from band edge

8.2. TEST SET-UP
Radiated same as 6.2

Conducted set up

EUT Spectrum analyzer
cable

Report No.: AGC10576170701FE08
Page 19 of 34

8.3. Radiated Test Result
Meter Emission
Frequency Factor Limits Margin Detector
Reading Level Comment
(MHz) (dBμV) (dB) (dBμV/m) (dBμV/m) (dB) Type
Low Channel (2402 MHz)
2399.9 65.60 -13 52.60 74 -21.40 peak Horizontal
2399.9 54.62 -13 41.62 54 -12.38 AVG Horizontal
2400 65.00 -12.99 52.01 74 -21.99 peak Horizontal
2400 52.76 -12.99 39.77 54 -14.23 AVG Horizontal
2399.9 64.57 -12.97 51.60 74 -22.40 peak Vertical
2399.9 54.28 -12.97 41.31 54 -12.69 AVG Vertical
2400 66.46 -12.94 53.52 74 -20.48 peak Vertical
2400 53.15 -12.94 40.21 54 -13.79 AVG Vertical
High Channel (2480 MHz)
2483.5 65.06 -12.78 52.28 74 -21.72 peak Horizontal
2483.5 56.62 -12.78 43.84 54 -10.16 AVG Horizontal
2483.6 66.23 -12.77 53.46 74 -20.54 peak Horizontal
2483.6 54.37 -12.77 41.60 54 -12.40 AVG Horizontal
2483.5 65.24 -12.76 52.48 74 -21.52 peak Vertical
2483.5 53.66 -12.76 40.90 54 -13.10 AVG Vertical
2483.6 65.79 -12.72 53.07 74 -20.93 peak Vertical
2483.6 55.77 -12.72 43.05 54 -10.95 AVG Vertical

RESULT: PASS
Note: Factor=Antenna Factor + Cable loss - Amplifier gain,
Emission Level = Meter Reading + Factor
Margin= Emission Level -Limit.
The “Factor” value can be calculated automatically by software of measurement system.

Report No.: AGC10576170701FE08
Page 27 of 34

12.3 PRELIMINARY PROCEDURE

1) The equipment was set up as per the test configuration to simulate typical actual usage per the user’s
manual. When the EUT is a tabletop system, a wooden table with a height of 0.8 meters is used and is
placed on the ground plane as per ANSI C63.10 (see Test Facility for the dimensions of the ground plane
used). When the EUT is a floor-standing equipment, it is placed on the ground plane which has a 3-12 mm
non-conductive covering to insulate the EUT from the ground plane.
2) Support equipment, if needed, was placed as per ANSI C63.10.
3) All I/O cables were positioned to simulate typical actual usage as per ANSI C63.10.
4) All support equipments received AC120V/60Hz power from a LISN, if any.
5) The EUT received power by adapter which received power by a LISN.
6) The test program was started. Emissions were measured on each current carrying line of the EUT using a
spectrum Analyzer / Receiver connected to the LISN powering the EUT. The LISN has two monitoring
points: Line 1 (Hot Side) and Line 2 (Neutral Side). Two scans were taken: one with Line 1 connected to
Analyzer / Receiver and Line 2 connected to a 50 ohm load; the second scan had Line 1 connected to a 50
ohm load and Line 2 connected to the Analyzer / Receiver.
7) Analyzer / Receiver scanned from 150 kHz to 30MHz for emissions in each of the test modes.
8) During the above scans, the emissions were maximized by cable manipulation.
9) The following test mode(s) were scanned during the preliminary test.
Then, the EUT configuration and cable configuration of the above highest emission level were recorded for
reference of final testing.

12.4 FINAL TEST PROCEDURE
10) EUT and support equipment was set up on the test bench as per step 2 of the preliminary test.
11) 2) A scan was taken on both power lines, Line 1 and Line 2, recording at least the six highest emissions.
Emission frequency and amplitude were recorded into a computer in which correction factors were used to
calculate the emission level and compare reading to the applicable limit. If EUT emission level was less
–2dB to the A.V. limit in Peak mode, then the emission signal was re-checked using Q.P and Average
detector.
12) 3) The test data of the worst case condition(s) was reported on the Summary Data page.

Report No.: AGC10576170701FE08
Page 30 of 34

13. CONDUCTED SPURIOUS EMISSION
13.1. MEASUREMENT PROCEDURE
1. Connect EUT RF output port to the Spectrum Analyzer through an RF attenuator
2. Set the EUT Work on the top, the Middle and the bottom operation frequency individually.
3. Set the Span = wide enough to capture the peak level of the in-band emission and all spurious emissions
from the lowest frequency generated in the EUT up through the 10th harmonic.
RBW = 100 kHz; VBW  RBW; Sweep = auto; Detector function = peak.
4. Set SPA Trace 1 Max hold, then View.
Note: The EUT was tested according to DA000705 for compliance to FCC 47CFR 15.247 requirements. Owing
to satisfy the requirements of the number of measurement points, we set the RBW=1MHz, VBW＞RBW, scan
up through 10th harmonic, and consider the tested results as the worst case, if the tested results conform to the
requirement, we can deem that the real tested results(set the RBW=100KHz, VBW＞RBW) are conform to the
requirement.

13.2. TEST SET-UP (BLOCK DIAGRAM OF CONFIGURATION)
The same as described in section 8.2

13.3. MEASUREMENT EQUIPMENT USED
The same as described in section 6

13.4. LIMITS AND MEASUREMENT RESULT
LIMITS AND MEASUREMENT RESULT
Measurement Result
Applicable Limits
Test Data Criteria
In any 100 KHz Bandwidth Outside the At least -20dBc than the limit
PASS
frequency band in which the spread spectrum Specified on the BOTTOM Channel
intentional radiator is operating, the radio frequency
power that is produce by the intentional radiator shall
be at least 20 dB below that in 100KHz bandwidth
within the band that contains the highest level of the
At least -20dBc than the limit
desired power. PASS
Specified on the TOP Channel
In addition, radiation emissions which fall in the
restricted bands, as defined in §15.205(a), must also
comply with the radiated emission limits specified
in§15.209(a))

Document Created: 2017-08-04 08:38:35
Document Modified: 2017-08-04 08:38:35

© 2025 FCC.report
This site is not affiliated with or endorsed by the FCC