I19Z61642-SEM01_HAC_Rev0_Part2

FCC ID: 2AM86U307AS

Test Report

Download: PDF
FCCID_4503352

No.I19Z61642-SEM01 ANNEX E DIPOLE CALIBRATION CERTIFICATE Dipole 835 MHz ©Copyright. All rights reserved by CTTL. Page 134 of 149

. . §3 Calibration Laboratory of {\\“\@’/s G Schweizerischer Kalibrierdienst Schmid & Partner ila\\é/{&% ( Service suisse d‘étalonnage Engineering AG C SS 5 Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland {'/"/fi\“\? Swiss Calibration Service uhstabe Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates References [1] ANSI—C63.19—2011 American National Standard, Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids. Methods Applied and Interpretation of Parameters: e Coordinate System: y—axis is in the direction of the dipole arms. z—axis is from the basis of the antenna (mounted on the table) towards its feed point between the two dipole arms. x—axis is normal to the other axes. In coincidence with the standards [1], the measurement planes (probe sensor center) are selected to be at a distance of 15 mm above the top metal edge of the dipole arms. e Measurement Conditions: Further details are available from the hardcopies at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. The forward powerto the dipole connector is set with a calibrated power meter connected and monitored with an auxiliary power meter connected to a directional couple®t While the dipole under test is connected, the forward power is adjusted to the same level. e Antenna Positioning: The dipole is mounted on a HAC Test Arch phantom using the matching dipole positioner with the arms horizontal and the feeding cable coming from the floor. The measurements are performed in a shielded room with absorbers around the setup to reduce the reflections. It is verified before the mounting of the dipole under the Test Arch phantom, thatits arms are perfectly in a line. It is installed on the HAC dipole positioner with its arms parallel below the dielectric reference wire and able to move elastically in vertical direction without changing its relative position to the top center of the Test Arch phantom. The vertical distance to the probe is adjusted after dipole mounting with a DASYS Surface Check job. Before the measurement, the distance between phantom surface and probe tip is verified. The proper measurement distance is selected by choosing the matching section of the HAC Test Arch phantom with the proper device reference point (upper surface of the dipole) and the matching grid reference point (tip of the probe) considering the probe sensor offset. The vertical distance to the probe is essential for the accuracy. e Feed Point Impedance and Return Loss: These parameters are measured using a Vector Network Analyzer. The impedance is specified at the SMA connector of the dipole. The influence of reflections was eliminating by applying the averaging function while moving the dipole in the air, at least 70cm away from any obstacles. e E—field distribution: E field is measured in the x—y—plane with an isotropic E—field probe with 100 mW forward power to the antenna feed point. In accordance with [1], the scan area is 20mm wide, its length exceeds the dipole arm length (180 or 9Omm). The sensor centeris 15 mm (in z) above the metal top of the dipole arms. Two 3D maxima are available near the end of the dipole arms. Assuming the dipole arms are perfectly in one line, the average of these two maxima (in subgrid 2 and subgrid 8) is determined to compensate for any non— parallelity to the measurement plane as well as the sensor displacement. The E—field value stated as calibration value represents the maximum of the interpolated 3D—E—field, in the plane above the dipole surface. The reported uncertainty of measurementis stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: CD835V3—1023_Aug19 Page 2 of 5

mm @7/"7L CAIET | Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASY5 V52.10.2 Phantom HAC Test Arch Distance Dipole Top — Probe Center 15 mm Scan resolution dx, dy = 5 mm Frequency 835 MHz # 1 MHz Input power drift <0.05 dB Maximum Field values at 835 MHz E—field 15 mm above dipole surface condition Interpolated maximum Maximum measured above high end 100 mW input power 106.7 V/im = 40.56 dBV/m Maximum measured above low end 100 mW input power 106.6 V/im = 40.56 dBV/m Averaged maximum above arm 100 mW input power 106.7 V/im £ 12.8 % (k=2) Appendix (AdditionaT assessments outside the scope of SCS 0108) Antenna Parameters » Frequency Return Loss Impedance 800 MHz 17.2 dB 41.4 Q — 9.3 jQ 835 MHz 25.2 dB 52.6 Q + 5.0 jQ 880 MHz 16.4 dB 62.6 Q —11.7 jQ 900 MHz 16.2 dB 52.8 Q — 15.9 jQ 945 MHz 24.1 dB 45.6 Q + 4.0 jQ 3.2 Antenna Design and Handling The calibration dipole has a symmetric geometry with a built—in two stub matching network, which leads to the enhanced bandwidth. The dipole is built of standard semirigid coaxial cable. The internal matching line is open ended. The antenna is therefore open for DC signals. Do not apply force to dipole arms, as they are liable to bend. The soldered connections near the feedpoint may be damaged. After excessive mechanical stress or overheating, check the impedance characteristics to ensure that the internal matching network is not affected. After long term use with 40W radiated power, only a slight warming of the dipole near the feedpoint can be measured. Certificate No: CD835V3—1023_Aug19 Page 3 of 5

Impedance Measurement Plot File View Channel Sweep Calibration Trace Scale Marker ~System Window Help s to.co (Beei 1: 200.000000 MHz —17 228 4B 5.00 2s cbooos sas 16.30048 3: $80.000000 MHz —16.370.48 0.00 — 5.00 _ hen y 00 halkt d 121 48 L10.00 — L15.00 X { \ 22. F20 00 T\ \ / css {/ L25.00 3 s L30.00 fas.co L40.00 Ch 1 Ava= |20 Ch1: Start 335.000 MHz ——— Stop 1.33500 GHz 1: £00.000000 MHz 41 .407 n ® 21455pF <q272e 0 »2; $25.000000 MHz 525620 953.81 pH 50041 a 3: $00.000000 MHz 625920 15451 pF —1.7050 » 4: 900,000000 MHz s281e n 11.120pF 453000 5; $45.000000 MHz as.5e0 n 665.57 pH sases n Ch1Avg= 20 Chi: Start 295.000 MHz —— Stop 1.33500 GHz Status CH 1: 11 ) C* 1—Port Avg=20 Delay LCL Certificate No: CD835V3—1023_Aug19 Page 4 of 5

DASY5 E—field Result Date: 26.08.2019 Test Laboratory: SPEAG Lab2 DUT: HAC—Dipole 835 MHz; Type: CD835V3; Serial: CD835V3 — SN: 1023 Communication System: UID 0 — CW ; Frequency: 835 MHz Medium parameters used: 0 = 0 S/m, & = 1; p =0 kg/m‘ Phantom section: RF Section Measurement Standard: DASYS (IEEE/IEC/ANSI €63.19—2011) DASY52 Configuration: Probe: EF3DV3 — SN4013; ConvF(1, 1, 1) @ 835 MHz; Calibrated: 03.01.2019 o Sensor—Surface: (Fix Surface) e Electronics: DAE4 Sn781; Calibrated: 09.01.2019 e Phantom: HAC Test Arch with AMCC; Type: SD HAC PO1 BA; Serial: 1070 e DASY52 52.10.2(1504); SEMCAD X 14.6.12(7470) e Dipole E—Field measuremen't @ 83S5MHz/E—Scan — 835MHz d=15mm/Hearing Aid Compatibility Test (41x361x1): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0, —6.3 mm Reference Value = 127.9 V‘/m; Power Drift=—0.01 dB Applied MIF = 0.00 dB RF audio interference level = 40.56 dBV/m Emission category: M3 MIF scaled E—field Grid 1 M3 Grid 2 M3 Grid 3 M3 40.08 dBV/m|40.56 dBV/m[40.51 dBV/m Grid 4 M4 Grid 6 M4 35.34 dBV/m 35.67 dBV/m Grid 7 M3 Grid 8 M3 Grid 9 M3 40.23 dBV/m|40.56 dBV/m |40.49 dBV/m A.91 —3.82 —5.74 —1.65 —9.56 0 dB = 106.7 V/m = 40.56 dBV/m Certificate No: CD835V3—1023_Aug19 Page 5 of 5

TTL CAIECT ; ; sys Calibration Laboratory of at i\_JL’wl G Schweizerischer Kalibrierdienst : $ ~ Schmid & Partner $y 2 Service suisse d‘étalonnage Engineering AG iboevex 2 znye C5 Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland ‘»,1/7;\?\\\\3 Swiss Calibration Service ulutals Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates Client (GTTH/(Auden)~ , Certificate No: CD1880V3—1018_Aug19 CALIBRATION CERTIFICATE Object CD1880V3 — SN: 1018 Calibration procedure(s) QA CAL—20.v7 Calibration Procedure for Validation Sources in air Calibration date: * (August26, 2019 This calibration certificate documentsthe traceability to national standards, which realize the physicalunits of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environmenttemperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter NRP SN: 104778 03—Apr—19 (No. 217—02892/02893) Apr—20 Power sensor NRP—291 SN: 103244 03—Apr—19 (No. 217—02892) Apr—20 Power sensor NRP—291 SN: 103245 03—Apr—19 (No. 217—02893) Apr—20 Reference 20 dB Attenuator SN: 5058 (20k) 04—Apr—19 (No. 217—02894) Apr—20 Type—N mismatch combination SN: 5047.2 / 06327 04—Apr—19 (No. 217—02895) Apr—20 Probe EF3DV3 SN: 4013 03—Jan—19 (No. EF3—4013_Jan19) Jan—20 DAE4 SN: 781 09—Jan—19 (No. DAE4—781_Jan19) Jan—20 Secondary Standards ID # Check Date (in house) Scheduled Check Power meter Agilent 44198 SN: GB42420191 09—Oct—09 (in house check Oct—17) In house check: Oct—20 Power sensor HP E4412A SN: US$38485102 05—Jan—10 (in house check Oct—17) In house check: Oct—20 Power sensor HP 8482A SN: US37205597 09—Oct—09 (in house check Oct—17) In house check: Oct—20 RF generator R&S SMT—06 SN: 837633/005 10—Jan—19 (in house check Jan—19) In house check: Oct—22 Network Analyzer Agilent E8358A SN: US41080477 31—Mar—14 (in house check Oct—18) In house check: Oct—19 Name Function Signature Calibrated by: Leif Klysner Laboratory Technician Approved by: Katja Pokovic Technical Manager /W; Issued: August 27, 2019 This calibration certificate shall not be reproduced exceptin full without written approval of the laboratory. Certificate No: CD1880Vv3—1018_Aug19 Page 1 of 5 ty —

Calibration Laboratory of &Fuy \\—_fi >, S Schweizerischer Kalibrierdienst Schmid & Partner i&z—/mfi% ( Service suisse d‘étalonnage Engineering AG zns 5 Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland "/"/fi\“\\\ Swiss Calibration Service Whilals Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreement for the recognition of calibration certificates References [1] ANSI—C63.19—2011 American National Standard, Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids. Methods Applied and Interpretation of Parameters: e Coordinate System: y—axis is in the direction of the dipole arms. z—axis is from the basis of the antenna (mounted on the table) towards its feed point between the two dipole arms. x—axis is normal to the other axes. In coincidence with the standards [1], the measurement planes (probe sensor center) are selected to be at a distance of 15 mm above the top metal edge of the dipole arms. e Measurement Conditions: Further details are available from the hardcopies at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. The forward powerto the dipole connector is set with a calibrated power meter connected and monitored with an auxiliary power meter connected to a directional couple® While the dipole under test is connected, the forward power is adjusted to the same level. e Antenna Positioning: The dipole is mounted on a HAC Test Arch phantom using the matching dipole positioner with the arms horizontal and the feeding cable coming from the floor. The measurements are performed in a shielded room with absorbers around the setup to reduce the reflections. It is verified before the mounting of the dipole under the Test Arch phantom, that its arms are perfectly in a line. It is installed on the HAC dipole positioner with its arms parallel below the dielectric reference wire and able to move elastically in vertical direction without changing its relative position to the top center of the Test Arch phantom. The vertical distance to the probe is adjusted after dipole mounting with a DASY5 Surface Check job. Before the measurement, the distance between phantom surface and probe tip is verified. The proper measurement distance is selected by choosing the matching section of the HAC Test Arch phantom with the proper device reference point (upper surface of the dipole) and the matching grid reference point (tip of the probe) considering the probe sensoroffset. The vertical distance to the probe is essential for the accuracy. e Feed Point Impedance and Return Loss: These parameters are measured using a Vector Network Analyzer. The impedance is specified at the SMA connector of the dipole. The influence of reflections was eliminating by applying the averaging function while moving the dipole in the air, at least 7Ocm away from any obstacles. ® E—field distribution: E field is measured in the x—y—plane with an isotropic E—field probe with 100 mW forward power to the antenna feed point. In accordance with [1], the scan area is 20mm wide, its length exceeds the dipole arm length (180 or 9Omm). The sensor center is 15 mm (in z) above the metal top of the dipole arms. Two 3D maxima are available near the end of the dipole arms. Assuming the dipole arms are perfectly in one line, the average of these two maxima (in subgrid 2 and subgrid 8) is determined to compensate for any non— parallelity to the measurement plane as well as the sensor displacement. The E—field value stated as calibration value represents the maximum of the interpolated 3D—E—field, in the plane above the dipole surface. The reported uncertainty of measurementis stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: CD1880Vv3—1018_Aug19 Page 2 of 5

Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASYS V52.10.2 Phantom HAC Test Arch Distance Dipole Top — Probe Center 15 mm Scan resolution dx, dy = 5 mm Frequency 1880 MHz & 1 MHz Input power drift <0.05 dB Maximum Field values at 1880 MHz E—field 15 mm above dipole surface condition Interpolated maximum Maximum measured above high end 100 mW input power 88.0 V/im = 38.89 dBV/m Maximum measured above low end 100 mW input power 86.5 V/im = 38.74 dBV/m Averaged maximum above arm 100 mW input power 87.3 V/im £ 12.8 % (k=2) Appendix (Additiona‘ assessments outside the scope of SCS 0108) Antenna Parameters » Frequency Return Loss Impedance 1730 MHz 27.8 dB 54.3 Q + 0.3 jQ 1880 MHz 21.6 dB 55.4 Q + 7.0 jQ 1900 MHz 22.8 dB 56.3 Q + 4.5 jQ 1950 MHz 33.3 dB 52.2 0 —0.1 jQ 2000 MHz 19.4 dB 47.6 Q + 10.2 jQ 3.2 Antenna Design and Handling The calibration dipole has a symmetric geometry with a built—in two stub matching network, which leads to the enhanced bandwidth. The dipole is built of standard semirigid coaxial cable. The internal matching line is open ended. The antenna is therefore open for DC signals. Do not apply force to dipole arms, as they are liable to bend. The soldered connections near the feedpoint may be damaged. After excessive mechanical stress or overheating, check the impedance characteristics to ensure that the internal matching network is not affected. After long term use with 40W radiated power, only a slight warming of the dipole near the feedpoint can be measured. Certificate No: CD1880V3—1018_Aug19 Page 3 of 5

TTL éCAIEFT y Impedance Measurement Plot Eile View Channel Sweep Calibration Trace Scale Marker ~System Window Help & mm m 7.00 aest1 1: 1.f30000 GHe 27.75448 240 ; $s0000 ou 24.570.40 3 1 trak eresar f3.00 — [¥ ts E2e hxon —]— _ afk 2 are L13.00 —=~. 3 L18.00 s Fa § £ es.00 on & \ / 3 * es .00 > * L33.00 1\+—f \ + 1 / 4 |as.00 tf— V} Lis.00 Ch 1 Avg= |20 Chi: Start 1.38000 GHa —— Stop 2.38000 GHz £ 1.730000 GHz s4.2ee n * 23.605pH 2574 m0 »2: 1.820000 GHz s5.377 0 590.65pH 6.9770 n 3: 1.900000 GHe se.27e n 376.44pH 4.4940 n » a 1.950000 GHz s2218 0 1.4376nF 46 5: 2.000000 GHz #10.79pH 10.183 0 Ch1Avg= 20 Ch1: Start 1.38000 GHz —— Stop 2.38000 GHz Status CH 1: 811 ] C" 1—Port Avg=20 Delay LCL Certificate No: CD1880V3—1018_Aug19 Page 4 of 5

@777 CA ET DASY5 E—field Result Date: 26.08.2019 Test Laboratory: SPEAG Lab2 DUT: HAC Dipole 1880 MHz; Type: CD1880V3; Serial: CD1880V3 — SN: 1018 Communication System: UID 0 — CW ; Frequency: 1880 MHz Medium parameters used: 0 = 0 S/m, & = 1; p = 0 kg/m‘ Phantom section: RF Section Measurement Standard: DASYS (IEEE/IEC/ANSI €63.19—2011) DASYS52 Configuration: Probe: EF3DV3 — SN4013; ConvF(1, 1, 1) @ 1880 MHz; Calibrated: 03.01.2019 e Sensor—Surface: (Fix Surface) o Electronics: DAE4 Sn781; Calibrated: 09.01.2019 e Phantom: HAC Test Arch with AMCC; Type: SD HAC PO1 BA; Serial: 1070 e DASY52 52.10.2(1504); SEMCAD X 14.6.12(7470) e Dipole E—Field measureme:t @ 1880MHz/E—Scan — 1880MHz d=15mm/Hearing Aid Compatibility Test (41x181x1): Interpolated grid: dx=0.5000 mm, dy=0.5000 mm Device Reference Point: 0, 0, —6.3 mm Reference Value = 151.1 V,/m; Power Drift=—0.01 dB Applied MIF = 0.00 dB RF audio interference level = 38.89 dBV/m Emission category: M2 MIF scaled E—field Grid 1M2 |erid 2 m2 |Grid 3 M2 38.47 dBV/m|38.89 dBV/m|38.86 dBV/m Grid 4 M2 | m Grid 6 M2 35.88 dBV/m 35.97 dBV/m Grid 7 M2 Grid 8 M2 Grid 9 M2 38.51 dBV/m|38.74 dBV/m|38.6 dBV/m —1.00 —2.01 —3.01 —4.02 —5.02 0 dB = 88.04 V/m = 38.89 dBV/m Certificate No: CD1880V3—1018_Aug19 Page 5 of 5

E"TTL CA ET /R Calibration Laboratory of Si/4 S Schweizerischer Kalibrierdienst Schmid & Partner il;: t‘//:"E—!“. C Service suisse d‘étalonnage Engineering AG $ mss 5 Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland {)"/1///_\?\\“? Swiss Calibration Service Ahilaks Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates Client (CTTE(Auden) Certificate No: CD2600V3—1017_Aug19 Object CD2600V3 — SN: 1017 Calibration procedure(s) QA CAL—20.v7 Calibration Procedure for Validation Sources in air * Calibration date: °_ August 23, 2019 This calibration certificate documents the traceability to national standards, which realize the physical units of measurements (S1). The measurements and the uncertainties with confidence probability are given on the following pages and are part of the certificate. All calibrations have been conducted in the closed laboratory facility: environmenttemperature (22 + 3)°C and humidity < 70%. Calibration Equipment used (M&TE critical for calibration) Primary Standards ID # Cal Date (Certificate No.) Scheduled Calibration Power meter NRP SN: 104778 03—Apr—19 (No. 217—02892/02893) Apr—20 Power sensor NRP—Z91 SN: 103244 03—Apr—19 (No. 217—02892) Apr—20 Power sensor NRP—Z91 SN: 103245 03—Apr—19 (No. 217—02893) Apr—20 Reference 20 dB Attenuator SN: 5058 (20k) 04—Apr—19 (No. 217—02894) Apr—20 Type—N mismatch combination SN: 5047.2 / 06327 04—Apr—19 (No. 217—02895) Apr—20 Probe EF3DV3 SN: 4013 03—Jan—19 (No. EF3—4013_Jan19) Jan—20 DAE4 SN: 781 09—Jan—19 (No. DAE4—781_Jan19) Jan—20 Secondary Standards ID # Check Date (in house) Scheduled Check Power meter Agilent 44198 SN: GB42420191 09—Oct—09 (in house check Oct—17) In house check: Oct—20 Power sensor HP E4412A SN: US38485102 05—Jan—10 (in house check Oct—17) In house check: Oct—20 Power sensor HP 8482A SN: US37205597 09—Oct—09 (in house check Oct—17) In house check: Oct—20 RF generator R&S SMT—06 SN: 837633/005 10—Jan—19 (in house check Jan—19) In house check: Oct—22 Network Analyzer Agilent E8358A SN: US41080477 31—Mar—14 (in house check Oct—18) In house check: Oct—19 Name Function Signature Calibrated by: Leif Klysner Laboratory Technician W %éé Approved by: Katja Pokovie Technical Manager %@ Issued: August 27, 2019 This calibration certificate shall not be reproduced except in full without written approval of the laboratory. Certificate No: CD2600V3—1017_Aug19 Page 1 of 5

éCADIEFT Calibration . Laboratory of wWSY s \\:///3 S Schweizerischer Kalibrierdienst Schmid & Partner ila\é.{&% C Service suisse d‘étalonnage Engineering AG T ag 5 Servizio svizzero di taratura Zeughausstrasse 43, 8004 Zurich, Switzerland ‘f,,/fi\\x‘ Swiss Calibration Service hilabs Accredited by the Swiss Accreditation Service (SAS) Accreditation No.: SCS 0108 The Swiss Accreditation Service is one of the signatories to the EA Multilateral Agreementfor the recognition of calibration certificates References [1] ANSI—C63.19—2011 American National Standard, Methods of Measurement of Compatibility between Wireless Communications Devices and Hearing Aids. Methods Applied and Interpretation of Parameters: e Coordinate System: y—axis is in the direction of the dipole arms. z—axis is from the basis of the antenna (mounted on the table) towards its feed point between the two dipole arms. x—axis is normal to the other axes. In coincidence with the standards [1], the measurement planes (probe sensor center) are selected to be at a distance of 15 mm above the top metal edge of the dipole arms. e Measurement Conditions: Further details are available from the hardcopies at the end of the certificate. All figures stated in the certificate are valid at the frequency indicated. The forward powerto the dipole connector is set with a calibrated power meter connected and monitored with an auxiliary power meter connected to a directional couple®. While the dipole under test is connected, the forward power is adjusted to the same level. e Antenna Positioning: The dipole is mounted on a HAC Test Arch phantom using the matching dipole positioner with the arms horizontal and the feeding cable coming from the floor. The measurements are performed in a shielded room with absorbers around the setup to reduce the reflections. It is verified before the mounting of the dipole under the Test Arch phantom, that its arms are perfectly in a line. It is installed on the HAC dipole positioner with its arms parallel below the dielectric reference wire and able to move elastically in vertical direction without changing its relative position to the top center of the Test Arch phantom. The vertical distance to the probe is adjusted after dipole mounting with a DASY5 Surface Check job. Before the measurement, the distance between phantom surface and probe tip is verified. The proper measurement distance is selected by choosing the matching section of the HAC Test Arch phantom with the proper device reference point (upper surface of the dipole) and the matching grid reference point (tip of the probe) considering the probe sensoroffset. The vertical distance to the probe is essential for the accuracy. e Feed Point Impedance and Return Loss: These parameters are measured using a Vector Network Analyzer. The impedance is specified at the SMA connector of the dipole. The influence of reflections was eliminating by applying the averaging function while moving the dipole in the air, at least 70cm away from any obstacles. ® E—field distribution: E field is measured in the x—y—plane with an isotropic E—field probe with 100 mW forward power to the antenna feed point. In accordance with [1], the scan area is 20mm wide, its length exceeds the dipole arm length (180 or 9Omm). The sensor centeris 15 mm (in z) above the metal top of the dipole arms. Two 3D maxima are available near the end of the dipole arms. Assuming the dipole arms are perfectly in one line, the average of these two maxima (in subgrid 2 and subgrid 8) is determined to compensate for any non— parallelity to the measurement plane as well as the sensor displacement. The E—field value stated as calibration value represents the maximum of the interpolated 3D—E—field, in the plane above the dipole surface. The reported uncertainty of measurement is stated as the standard uncertainty of measurement multiplied by the coverage factor k=2, which for a normal distribution corresponds to a coverage probability of approximately 95%. Certificate No: CD2600V3—1017_Aug19 Page 2 of 5

éAIEFT Measurement Conditions DASY system configuration, as far as not given on page 1. DASY Version DASYS V52.10.2 Phantom HAC Test Arch Distance Dipole Top — Probe Center 15 mm Scan resolution dx, dy = 5 mm Frequency 2600 MHz # 1 MHz Input power drift <0.05 dB Maximum Field values at 2600 MHz E—field 15 mm above dipole surface condition Interpolated maximum Maximum measured above high end 100 mW input power 84.8 V/im = 38.57 dBV/m Maximum measured above low end 100 mW input power 83.4 V/im = 38.42 dBV/m Averaged maximum above arm 100 mW input power 84.1 V/im £ 12.8 % (k=2) Appendix (Additionafi assessments outside the scope of SCS 0108) Antenna Parameters x Frequency Return Loss Impedance 2450 MHz 24.2 dB 44.3 Q + 1.0 jQ 2550 MHz 22.2 dB 57.1 Q + 4.4 jQ 2600 MHz 20.7 dB 59.5 Q — 3.5 jQ 2650 MHz 19.3 dB 55.4 Q —10.1 jQ 2750 MHz 15.6 dB 40.8 Q — 12.1 jQ 3.2 Antenna Design and Handling The calibration dipole has a symmetric geometry with a built—in two stub matching network, which leads to the enhanced bandwidth. The dipole is built of standard semirigid coaxial cable. The internal matching line is open ended. The antenna is therefore open for DC signals. Do not apply force to dipole arms, as they are liable to bend. The soldered connections near the feedpoint may be damaged. After excessive mechanical stress or overheating, check the impedance characteristics to ensure that the internal matching network is not affected. After long term use with 40W radiated power, only a slight warming of the dipole near the feedpoint can be measured. Certificate No: CD2600V3—1017_Aug19 Page 3 of 5

éAIEFT Impedance Measurement Plot File View Channel Sweep Calibration Trace Scale Marker ~System Window Help 7.00 tesu 2450000 GHe 24207 4B 2.00 Acoses ou 0148 $: 2400000 GHz _|_—20.570494 f3.00 3 T He |zsds s.00 e & — ~CTSANON GH= «15 57A *~. L13.00 ~ 3 =~ F1s.00 .. ,,_,/::/ L2s.00 Las oo : LG&OU Las.co 00 Ch 1 Avg= |20 Ch1: Start 2.10000 GHz —— Stop 3.10000 GHz 1 2.450000 GHz 44.278 0 ® 64.845pH 998.22m0 8: 2550000 GHz 57 .069 n 27351 pH 43823 0 >3 2600000 GHz 59.524 0 17519pF 449410 # 4: 2.650000 GHz s5 .437 n 59082pF A0.1140 s 2.750000 GHz 47723 pF Ch1Avg= 20 Chi: Start 2.10000 GHz —— Stop 3.10000 GHz en Status CH 1: 511 | C" 1—Port Avg=20 Delay ECE Certificate No: CD2600V3—1017_Aug19 Page 4 of 5


Document Created: 2019-10-30 15:35:37
Document Modified: 2019-10-30 15:35:37
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC