User Manual

FCC ID: 2ALHR005

Users Manual

Download: PDF
FCCID_4065596

2ALHR005Module User's Manual 1. Features ‐ On‐chip low power microcontroller ‐ 128KB of In‐system programmable flash ‐ 8KB SRAM ‐ On board crystal and PCB Antenna 2. Application ‐ Mobile device accessories (Android/ iOS) ‐ Wireless data communication ‐ Remote sensors 3. Pin definition (from right to left) Pin No. Description Pin Type Functions 1 BLE_RX Digital I/O UART RX 2 BLE_TX Digital I/O UART TX 3 WAKE_UP Output Digital I/O 4 STATUS Input Digital I/O 5 GND Digital I/O GND 6 V+ Digital I/O VDD 7 BLE_EN Digital I/O VDD Enable 4. How to use: ‐ Before sending any UART Command, "WAKE_UP 1  0" must be done by external MCU. ‐ If the RF module is connected to Smart Devices (Android/ iOS), the pin STATUS will be logic "1" to inform external MCU.

‐ Beacon 1. Send Command 'R' to send live measured data from external through Beacon. 2. This is default mode, and RF module send data only. Cannot receive any data. ‐ BLE 1. Send Command 'M' to switch mode from Beacon to BLE. 2. After the mode switch successfully, the external MCU can receive data from Smart phone. ‐ Receiver 1. Send Command 'E'/'G'/'I' to switch mode from Beacon to Receiver. 2. Only specific Beacon data can be received, and the external MCU receives the data from UART 5. Protocol: ‐ UART Baud Rate: 115200, 8, N, 1 ‐ Commands 'M': Mode Switch External MCU RF Module Starter Len OP S/N CK End # M (0D 0A)h External MCU RF Module Starter Len OP Indi CK End > M (0D 0A)h

'I':Scan Product Information of multiple products External MCU RF Module Starter Len OP Filter1 Filter2 Filter3 Filter4 Filter5 '#' 'I' Filter6 Filter7 Filter8 CK End (0D 0A)h External MCU RF Module Starter Len OP Beacon Data RSSI CK End '>' 'I' (0D 0A)h 'C': Scan stop External MCU RF Module Starter Len OP CK End '#' 'C' (0D 0A)h External MCU RF Module Starter Len OP CK End '>' 'C' (0D 0A)h 'X': Setting RF Module parameter External MCU RF Module Starter Len OP Setting FP Prod. S/N Cal. Date Tx Power CK End # X (0D 0A)h External MCU RF Module Starter Len OP FP Prod SN Cal Date Tx Power BLE_Ver CK End > X (0D 0A)h 'R': Send Beacon data External MCU RF Module Starter Len OP Beacon Data CK End '#' 'R' (0D 0A)h External MCU RF Module Starter Len OP Indi CK End '>' 'R' (0D 0A)h

'E': Scan beacon information of one product External MCU RF Module Starter Len OP Product Code CK End '#' 'E' (0D 0A)h External MCU RF Module Starter Len OP Beacon Data RSSI CK End '>' 'E' (0D 0A)h 'G': Scan beacon information of all products External MCU RF Module Starter Len OP CK End '#' 'G' (0D 0A)h External MCU RF Module Starter Len OP Beacon Data RSSI CK End '>' 'G' (0D 0A)h FCC Compliance and Advisory Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: . Reorient or relocate the receiving antenna. . Increase the separation between the equipment and receiver. . Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. . Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. The module is limited to OEM installation ONLY. This module is intended for OEM integrators under the following conditions: 1. This module is restricted to installation in products for use only in mobile and fixed applications. 2. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons. 3. The antenna(s) used for this transmitter must not transmit simultaneously with any other antenna or transmitter. The OEM integrator is still responsible for 1. ensuring that the end-user has no manual instructions to remove or install module 2. the FCC compliance requirement of the end product, which integrates this module. 3. Appropriate measurements (e.g. 15 B compliance) and if applicable additional equipment authorizations (e.g. Verification, Doc) of the host device to be addressed by the integrator/manufacturer. 4. The separate approval is required for all other operating configurations, including portable configurations with respect to Part 2.1093 and different antenna configurations Guidance to the Host Manufacturer: 1. Module grantee (the party responsible for the module grant) shall provide guidance to the host manufacturer for ensuring compliance with the Part 15 Subpart B requirements. The user manual of the end product should include 1. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. 2. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter.

3. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. 4. The FCC part 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Label of the end product: The final end product must be labeled in a visible area with the following " Contains TX FCC ID: 2ALHR005 ". The end product shall bear the following 15.19 statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. L’émetteur/récepteur exempt de licencecontenudans le présentappareilestconforme aux CNR d’Innovation, Sciences et Développementéconomique Canada applicables aux appareils radio exempts de licence. L’exploitationestautorisée aux deux conditions suivantes : 1. L’appareil ne doit pas produire de brouillage; 2. L’appareildoitaccepter toutbrouillageradioélectriquesubi, mêmesi le brouillageest susceptible d’encompromettre le fonctionnement. IMPORTANT NOTE: IC Radiation Exposure Statement: This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Cetéquipementestconforme aux limitesd’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cetéquipementdoitêtreinstallé et utilisé avec un minimum de 20cm de distance entre la source de rayonnement et votre corps

OEM integrator is still responsible for testing their end product for any additional compliance requirements required with this module installed (for example, digital device emissions, PC peripheral requirements, etc.). IMPORTANT NOTE: In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the IC authorization is no longer considered valid and the IC No. cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate IC authorization. Modular OEM Integrator Notice End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains transmitter module IC: IC: 22518-BT005”. Contient le module d'émission IC: IC: 22518-BT005 This device is intended only for OEM integrators under the following conditions: 1) The antenna must be installed such that 20cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. Cetappareilestconçuuniquement pour les intégrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antennedoitêtreinstallée de tellesortequ'une distance de 20cm estrespectée entre l'antenne et les utilisateurs, et 2) Le module émetteurpeut ne pas êtrecoïmplanté avec unautreémetteurouantenne. CAN ICES-3 (B)/NMB-3(B)


Document Created: 2018-10-30 17:11:03
Document Modified: 2018-10-30 17:11:03
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC