User Manual

FCC ID: 2ALGRPLX-GV70

Users Manual

Download: PDF
FCCID_3391104

Cell Phone Signal Solutions Cell Phone Signal Solutions Installation Of Omni—directional Antenna 5. Indoo installatio Proper antennas shell be selected according to the site condtions and the requirement. And more than one antenna can be used with the repeater, especialy for repeaters equal wih or over 208m, and 30dBm can be connected wih up to 10 antennas in order to send the signals to larger areas or distrbute the signals equally. Please consult our professional engineers about the soluton if you want to connect more than one antenna. Test the call quality of Outdoor antenna (for professional installation team only) (1) Indoor celing Omni antennais sutable to be installd in the conter and raiate all directins. Lightening Fix the Outdoor antennaafter selecting the best position, and adjust slightly its height or angles in order to get the signals with suitable input power level and caling quality. 4.3.Cable layout and connector assembly (1) Keep the type, specifications, routing direction, location, and curvature radius of cables in compliance with the design requirement, Place cables in good order, bend them smoothly, and protect the outer skin: against any damage. (2) Bind cables in good order when laying them on cable racks When leading cables in or out of roughs, use a hole—opener to open cable troughs and then install PVC lock—nuts to protect them. (3)Keep horizontal cables straight and fasten them stably with a fixing clip every 1 to 1.5 meters , with a proper stress. (4)Bind and fasten vertical cables every two to three meters to avoid damaging cables or connectors owing to their own heavy weight. Take back the cables and re—lay them when you have difficulty in pulling (2) Itis betterto use a directional panel antenna when the coverage shape is long and narrow (cortidors, long them, and avoid using a strong force to pull them. tow of houses in two sides, tunnels or elevators or rural open space). 5) Separate RF cables from power cables . Take properisolation measuresif they haveto be placed on the same cable racks owing to the site condition restriction. (6) Correctly fasten all connection parts ofthe whole system , from the antenna to active interfaces to passive interfaces, and keep electrical interfaces well contacted . Give waterproof treatment to Outdoor connection parts. (7) Take lightning protection measures for the antenna and feeder system in accordance with the design requirement. Avoid deforming the antenna feeder where grounding clips are placed, and give waterproof treatment to the feeder. (8) Keep exposed Indoor cables in good order Install PVC troughs or tubes if the exposed cables are more than 1 meter long. Place small passive RF parts such as power splitter in cable troughs. (9) Process both ends of RF coaxial cables as follows: @Keep the same redundant cable length and keep the length of stripped cables to agree with the corresponding connectors. @ Use a proper force to cut the Jacket layer or insulation layer and avoid damaging the braid shielded net and cores. eWeld cores firmly and smoothly with a proper amount of solder, without solder projections or nodules. Assemble coaxia! cables strietly in accordance with the installation specifications. © Keep a moderate length of heat—shrinkable tubes and heat—shrink the tubes eveny when adding heat— shrinkable tubes to the end of cables. © Protect the ends of cables against water and dampness. Use waterproof tape to give waterproof treatment to exposed cable ends. Cut off the end i it is dampened or water—soaked.

Cell Phone Signal Solutions Cell Phone Signal Solutions 3) The small whip antenna is suitable to be installed use for small room or apartment. Iis very convenient for 5.1.2. Repeater‘s ports description simple use wth a good resutt 1) Outdoor Port connected wih the outdoor antonna by cable. 2). Indoor Port connected with indoor antenna diectly or by cable: 3) DG Port connected with power supply Outdoor Antenna« Ci=) ourbooR ANTENNA 3 /L Boosters 5.1. Repeater Installation 5.1.3. Accessories selection 5.1.1. Installation Steps Please pay attention to the two poins of"frequency"andimpedance."uring the selection of the accessories. The Repeater shallbe installed in Indoor areas only All accessories shall support the repeater‘s frequencies from feeder ine, antenna and spliter to combiners etc. For example, the repeater‘s frequency is GSM900, so all the accessories must support the GSM900 1). Gonnect the power supply and the cables property to the repeater ports. frequency. And the repeater‘s impedance is 50ohm, so the accessories shall all be 50chm, To use any other impedance of coax will put an extra load on your repeater, shorten its e span and decrease the system 2): Check again to make sure the repeater is installed fimly and repeater alarm LED must stay green. pertormance. 5.1.4. Switch on power After poweris on, check firstly the alarm and power LEDs. Status and definition of POWER indicators: Status Definition Green Normal Off DC power problem EP

Cell Phone Signal Solutions Cell Phone Signal Solutions @Remark: 5.1.5. Check whether the coverage is good Increase the output power® ———recommended ways: adjust the Outdoor antenna direction (1) Have a test wih mobile phone or data card (engineering mobile phone is preferred), If the signals in most [ location, or replace with higher gain antenna to increase input signal strength. areas have not been improved, please check below again: 5.16Repeater does not communicate in Power—ON status © The weak input signal leads to the low output power. Change the direction of Outdoor antenna or ts installation postion or replace Outdoor antenna with higher gain antenna to increase input signal (1)The power is on but can not to call the phones. power lvel. it shallbe caused by the insufcient isolation between Outdoor antenna and serve antenna. © Check whother it is necessary to add more. Indoor antennas since bariers block the signal Please take below measures: penetration, also check whether the repeater s powsis enough; please install more Indoor antennas Firsty check whether the connection is correct. or replace with a repeater of higher power level. 4; Secondly adjust the antennas‘ directions orlocations or enlarge the distance between them. (2) If the signals in small part of the areas have not been improved, please check below: Thirdly replace a lower gain repeater if you have one backup. © Check whether the service antenna is installed correctly or not, you may try to move the antenna The following measures can also be tried: location to improve coverage. ¥ Use the roof ofthe building to enlarge the isolation (Please try t place the Outdoor antenna and Indoor © Check i itis necessary to adjust the direction of the sever antenna. antenna in different floors). © Check whetheritis necessary to add one or more antenna to enhance the coverage of special areas. J Use some obstacies (Such as wal). (2) The repeater‘s poweris on but the phone is not connected into the network and still cannot communicate. Reason 1: There are loose or wrong connections in the repeater system. ¥ Solution: Please try to fasten the connections between the different parts of the system. ¥ Reason 2: The signals received by Outdoor antenna of other operators nearby are too strong. 1)Move service antenna (For example, the other operators‘ signals are 10 dB strongerthan the needed signals.) 2)Increase. the number. of % Solution 1: Change the direction of Outdoor antenna or its installation position, so that the service antennas gap of signal strength is reduced between operators. 3)Increase the output power Solution 2: Use bartiers (like buildings) to block signals of other operators. 4 1)Move serviceantenna 2)Increase the. number. of Check call service antennas qualiy 3)Increase the output power Completion —14—

SAFETY INFORMATION CONNECTING THE BOOSTER The Federal Communications Commission(FCC) has tested this product and found The outside antenna receives a signal form the cell tower and passes them to the it to comply with their RF Exposure Requirements,pursuant to FCC Part 22 and 24. booster, which amplifies the signal and transmits it to your cell phone via the internal antenna. The inside antenna receives the outgoing signal from your cell phone and To comply with the FCC RF exposure requirements, keep the human user‘s passes it to the booster, which amplifies the signal and sends it to the outside antenna. body at least 8" (20cm) from the indoor antenna of the booster. The outside antenna transmits the signal back to the cell tower Don‘t expose this product to extreme low or high temperature (—20°C and 55°C). There are no consumer serviceable or modifiable parts inside this booster product Alteration or abuseof the booster or other components will void this product‘s warranty, and could be dangerous to the user. 1.Connect the Outside Antenna :The magnetic antenna is for outdoor use only. Select an outside mounting location. For best performance, keep the antenna on top of the vehicle. The outside antenna should be located in an area with at least 12" (30cm) of PACKAGE CON space on all sides that is free of obstructions, and other radiating elements such as a radio antenna. Screw the outside antenna to the outdoor connector of the booster, and then tighten it until snug. Do not over—tihhten. ® 40db Booster © Magnetic Mount Antenna ® Patch Antenna ®@ Velcro And Screw Mounting Kit 2.Connect the Inside Antenna: The patch antenna is intended for indoor use only. Do not mount on a surface within 4"(10em) of metal. Screw the patch antenna to the Indoor @ User Manual (This Document) connector on the booster. The patch antenna must be placed directly on the cell phone or cellular data card with the VELCRO provided for best results. The cable is long enough to reach the booster and cradle location for convenience of use. The booster is designed to be used while the cell phoneis in its cradle or connected to a cellular modem. If the phone is disconnected from the cradle , reception will significantly decrease. Note: The inside and outside antennas should be at least 6‘ (2 m)apart, if possible. 3.Connect the Power Cord: Connectthe DC power cord into the vehicle‘ s DC power source, Verify that all of the connections to the boosterare tight and secure, plugging the power cord to the booster, the green LED light will glow, indicating that the booster is ready to use. Note: You may purchase an optional AC power supply if you wantto use the booster as an indoordesktop system. WARNING: The booster is rated for DCBV input voltage. DO NOT use the booster with a higher—voltage power supply. This could damage the booster or cause personal injury. 4.Mounting the booster (optional): Select a location to install the booster that is away form excessive heat, direct sunlight or moisture and that has proper ventilation. Recommended installation locations are: Usually you should get the Mobile Booster kit like picture I or I, it includes everything Under the seat you need for installation. Before using it , please confirm yourBooster‘s frequency Under the dash range is correct with your service network, otherwise, the amplifier will not proper working for you. 15— ~16—

WarningThus us a CONSUMER device.BEFORE USE, you MUST REGISTER THIS DEVICE with your wireless provider and have your provider's consent. Most wireless providers consent to the use of signal boosters. Some providers may not consent to the use of this device on their network. If you are unsure, contact your provider. You MUST operate this device with approved antennas and cables as specified by the manufacturer.Antennas MUST be installed at least 20 cm (8 inches) from any person. You MUST cease operating the device immediately if requested by the FCC or a licensed wireless service provider.WARNING. E911 location infomation may not be provided or may be inaccurate for calls served by using the device.


Document Created: 2017-04-01 18:23:33
Document Modified: 2017-04-01 18:23:33
© 2024 FCC.report
This site is not affiliated with or endorsed by the FCC